On this page
ADs that cite it · 1
Newest first, with the revision each names, as OpenAirDocs read it from the AD’s text: check it against the AD.
Also cited in 1 proposed AD.
Text · 16
From the PDF’s text layer: layout, tables and figures are lost. The PDF is the document. © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2022-1646; AD 2023-04-01 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '2c7c574426b975d707b052b61308a63206ca5097d3a28a85cbd5ac3fcfe233ce' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '2c7c574426b975d707b052b61308a63206ca5097d3a28a85cbd5ac3fcfe233ce' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
SPECIAL CHECK/REWORK – PASSENGER DOOR –
INSPECT AND MEASURE THE STEPS & GAPS AND DOOR STOPS RIGGING The information below is provided for your reference. For full details, including labor and part coverage, please see corresponding paragraph contained within this bulletin.
RECOMMENDED
SPECIFIED TIME COMPLIANCE
COMPLIANCE TIME Within 72 months from this Service Bulletin release date (Basic Issue) EFFECTIVITY: A/C Serial No. 70006 to 70061 MANPOWER: Refer to Paragraph 1.F.
CONTINUED AIRWORTHINESS (CAW)
FLEET CAMPAIGN YES NO
AIRWORTHINESS LIMITATIONS (AWL) NOYES KITS and/or PARTS NOYES
TOOLING/GSE YES NO PLANNING INFORMATION: See important information at the start of Paragraph 1. YES NO
DEDICATED SCHEDULE NOYES PREREQUISITE SERVICE BULLETINS: NA NOTE: This Service Bulletin may be subject to an Airworthiness Directive which will make it necessary to implement this Service Bulletin.
SERVICE BULLETIN SUMMARY my.businessaircraft.bombardier.com MODEL BD−700−2A12 (BD−700) ATA 52−11 DOORS Basic Issue: Jul 22/2022 700−52−7511 Page 1 of 1 This Service Bulletin is available at:
SPECIAL CHECK/REWORK – PASSENGER DOOR –
INSPECT AND MEASURE THE STEPS & GAPS AND DOOR STOPS RIGGING
1. PLANNING INFORMATION NOTES:1 . Before you do this Service Bulletin, examine all STC, STA or equivalent action changes to make sure that this Service Bulletin can be completed.
2. All aircraft must send the recorded measurements to Bombardier Customer Support Engineering.
A. Effectivity BD−700−2A12 Aircraft Serial No. 70006 to 70061.
NOTE: The instructions given in this Service Bulletin are only applicable to the systems and parts installed at the time of delivery of the aircraft or as changed by Bombardier Aviation Service Bulletin(s).
B. Reason
1. Condition:
Rigging of the door pressure stop fittings and the steps and gaps can be affected by the aircraft’s loading condition whether on jacks or Weight−on−Wheels (WoW). A number of aircraft may be affected by this rigging as it was not performed in the final WoW configuration.
2. Objective/Benefit:
This Service Bulletin instructs to measure the passenger door steps and gaps, and rigging of door stops. If the measurements are not within the limits, re−adjustment to be done to obtain the necessary limits.
SERVICE BULLETIN my.businessaircraft.bombardier.com MODEL BD−700−2A12 (BD−700) ATA 52−11 DOORS Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations and/or acceptable industry standards.
This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior written consent of Bombardier Inc. and/or its affiliates.
2022 Bombardier Inc. All rights reserved Learjet, Challenger, Global, are registered trademarks of Bombardier Inc. or its subsidiaries.
Basic Issue: Jul 22/2022 700−52−7511 Page 1 of 13 This Service Bulletin is available at:
C. Description This Service Bulletin gives instructions in PART A to:
− Measure and record the passenger door steps and gaps, − Send the recorded measurements to Bombardier Customer Support Engineering.
This Service Bulletin gives instructions in PART B to:
− If the measurements are not within limits, re−adjust (rigging) to get the necessary limits, and − Send the recorded measurements to Bombardier Customer Support Engineering.
This Service Bulletin gives instructions in PART C to:
− Measure and record the passenger door stops rigging, − Send the recorded measurements to Bombardier Customer Support Engineering.
This Service Bulletin gives instructions in PART D to:
− If the measurements are not within limits, re−adjust (rigging) to get the necessary limits, and − Send the recorded measurements to Bombardier Customer Support Engineering.
D. Compliance Specified Time Compliance Recommended within 72 months from this Service Bulletin release date (Basic Issue).
NOTE: If it is not possible to complete all the instructions in this Service Bulletin because of the aircraft configuration, submit an SRPSA for analysis and to get an approved disposition to complete this Service Bulletin. Standard SRPSA fees may apply. Refer to the Services section of the Bombardier customer portal for the latest prices, rates and fees.
E. Approval The technical content of this Service Bulletin has been approved under the authority of Transport Canada Civil Aviation (TCCA) Design Approval Organization (DAO) No. DAO #93−Q−02.
NOTES: 1. The technical content of this Service Bulletin is accepted by the FAA under the Canada/USA bilateral Aviation Safety Agreement.
2. The technical content of this Service Bulletin is accepted by EASA under the Canada/EU bilateral Aviation Safety Agreement.
MODEL BD−700−2A12 (BD−700) Basic Issue: Jul 22/2022 700−52−7511 Page 2 of 13
F. Manpower NOTES: 1. The man−hours given are to help you schedule the tasks given in this Service Bulletin. The man−hours are for direct labor performed by an experienced crew and do not include the time for familiarization, planning, aircraft preparation in hangar such as towing and positioning of scaffolds, removal of interior furnishings, repainting, supervision and inspection.
For more information related to the manpower, refer to SB 700−00−7502.
2. Labor hours are based on the fact that the modification will be done at the next scheduled maintenance task or inspection. Therefore no man−hours are allotted to prepare the aircraft for maintenance or to prepare for this Service Bulletin.
02 man−hours are necessary to do PART A of this Service Bulletin.
28 man−hours are necessary to do PART B of this Service Bulletin.
02 man−hours are necessary to do PART C of this Service Bulletin.
12 man−hours are necessary to do PART D of this Service Bulletin.
The labor required to do this Service Bulletin is at no cost if:
− the work is done during new aircraft warranty period, and − the work is done at Bombardier Business Aviation Services (BBAS) or Authorized Service Facilities (ASF), and G. Material − Cost and Availability No kit or parts are necessary to do this Service Bulletin. For material data, refer to Paragraph 3.C.
H. Tooling The equipment and tools listed below are necessary to do this Service Bulletin:
SGSE/GSE REFERENCE NO. PART NO. DESCRIPTION 20−00−03 − Force gauge (2 to 100 lbs) 20−00−04 950−315 Digital Inclinometer 21X78K−21−01 − Fuselage−pressurizationadapter−panel kit 21X−00−05 − Safety net MODEL BD−700−2A12 (BD−700) Basic Issue: Jul 22/2022 700−52−7511 Page 3 of 13
SGSE/GSE REFERENCE NO. PART NO. DESCRIPTION 21X78K−00−02 − Safety netpressurization−baggage−door 21X78K−00−01 − Cabin pressurization cart 52X78K−11−02 − Manual−release−system NLGquadrant/PAX−door rig pin Commercially Available STD−0150 Digital stopwatch Commercially Available STD−0084 Feeler Gauge Commercially Available STD−0044 Ruler or Straightedge Commercially Available STD−0020 Torque Wrench NOTES: 1. Refer to the Global 7500 Illustrated Tool and Equipment Publication (ITEP) to make sure that you use the correct equipment configuration.
2. Refer to the Liability Statement in the ITEP for the G7500 for acceptable GSE equivalents.
3. This list is provided for quick reference. In case of discrepancy between this list and the tools called in the AMP, WM, Chapter 20, then the tools called in the AMP, WM prevail. Other approved alternative tools are acceptable and can also be used.
I. Weight and Balance No change.
J. Electrical Load Data No change.
K. References − TCCA Airworthiness Directive, (pending).
− Bombardier Aviation, Restriction and/or Special Instruction (RSI), C−70623, Rev. −−.
− Bombardier Aviation, Functional Test Engineering Requirement, FTER−CC700−521002, Rev. K.
− Global 7500 Aircraft Maintenance Publication (AMP), Chapters 6, 20, 24 and 52.
− Global 7500 Aircraft Structure Repair Publication (ASRP), Chapter 51.
MODEL BD−700−2A12 (BD−700) Basic Issue: Jul 22/2022 700−52−7511 Page 4 of 13
L. Other Publications Affected None.
M. Equivalent Service Bulletins None.
2. ACCOMPLISHMENT INSTRUCTIONS NOTES: 1. All TASKs given in the procedures that follow are from the Global 7500 BD−700−2A12, Aircraft Maintenance Publication (AMP) unless otherwise specified.
2. All references made to zones, access panels and/or doors, are from the Global 7500 BD−700−2A12 Aircraft Maintenance Publication (AMP), Chapter 6.
A. Aircraft Setup
(1) Obey all electrical/electronic safety precautions. Refer to BD700−A−J24−00−00−00AAA−012A−A.
(2) Obey all passenger−door safety precautions. Refer to BD700−A−J52−11−00−00AAA−012A−A.
(3) Obey all landing−gear safety precautions. Refer to BD700−A−J32−00−00−00AAA−012A−A.
B. PART A — Measurement of Passenger Door Steps and Gaps
(1) Measure and record the passenger door steps and gap values on each lateral side of the door at 8 points, and on the lower and upper side of the door at 4 points. Refer to Figure 1 and the table below:
MODEL BD−700−2A12 (BD−700) Basic Issue: Jul 22/2022 700−52−7511 Page 5 of 13
DOOR POINTS GAP VALUE STEP VALUE P1 to P8 (Between door skin forward−edge and fuselage skin)
0.070 to 0.170 in
(1.78 to 4.31 mm) −0.116 to −0.004 in (−2.95 to −0.10 mm) P13 to P20 (Between the door lower−skin edge and the fuselage lower−skin edge) P9 to P12 (Between the door lower−skin edge and the fuselage lower−skin edge)
0.090 to 0.170 in
(2.29 to 4.31 mm P21 to P24 (Between the door upper−skin edge and the fuselage upper−skin edge)
0.140 to 0.220 in
(3.56 to 5.58 mm) NOTES: 1. The values are for “Before Pressurization”, this is to comply with final values mentioned in airframe aerodynamics smoothness per ASRP BD700−A−J51−14−04−00AAA−361A−A, when aircraft is “Pressurized”.
2. At least three of the four guide rollers must contact the guides on the inboard surface during steps measure.
The gap on the fourth roller must be 0.000 to 0.020 in (0.00 to
0.50 mm).
3. Measure points to be at 1 in (25.4 mm), from the skin radius corner.
4. Measure point to be at 1 in (25.4 mm), above fasteners row due to the skin fuselage overlap.
(2) Send all the recorded values to Bombardier Customer Support Engineering through SRPSA by e−mail at SRPSA@aero.bombardier.com.
(3) If the above measurement is within the limits, go to PART C.
(4) If the above measurement is not within the limits, go to PART B.
C. PART B — Re−adjustment of Passenger Door Steps and Gaps NOTE: If the aircraft has a paint stripe running through the passenger door, doing a vertical rigging may result in mismatch of paint stripe.
MODEL BD−700−2A12 (BD−700) Basic Issue: Jul 22/2022 700−52−7511 Page 6 of 13
(1) If any of the measurement obtained from PART A is not within the limits, re−adjust to obtain the necessary values. Do as follow:
1. Do the rigging of passenger door. Refer to Step 3, 4, 5, 6, 7, 8 and 9 from BD700−A−J52−11−01−00AAA−275A−A.
2. Do the adjust procedure for passenger−door closed proximity−sensor.
Refer to BD700−A−J52−72−03−00AAA−271A−A.
3. Do the function test procedure for passenger door handles. Refer to BD700−A−J52−11−05−02AAA−340A−A.
4. Do the operational test procedure for the passenger door. Refer to BD700−A−J52−11−01−00AAA−320A−A.
5. Do the procedure to pressurize the cabin to a differential pressure of 4.00 psid (27,58 kPa). Refer to BD700−A−J21−31−00−00AAA−364A−A.
(2) Send all the recorded values to Bombardier Customer Support Engineering through SRPSA by e−mail at SRPSA@aero.bombardier.com.
(3) No further action required for PART C and D. Go to Close−out.
D. PART C — Measurement of Passenger Door Stops NOTE: PART C and D should be disregarded if the passenger door is re−rigged in PART B.
(1) With the door in closed position, measure and record the passenger door stops gaps. Refer to Figure 2 and the table below:
LOCATION GAP VALUE Between all the 10 lateral door stops and the fuselage stop fittings.
Refer to Figure 2, Detail E.
0.001 to 0.005 in
(0.03 to 0.12 mm) Between the 2 lower door stops and the fuselage stop fittings.
Refer to Figure 2, Detail D.
0.001 to 0.005 in
(0.03 to 0.12 mm) Between the 2 upper door stops and the fuselage stop fittings.
Refer to Figure 2, Detail B.
0.001 to 0.025 in
(0.03 to 0.63 mm) Between the lateral side of upper door stops and the fuselage stops.
Refer to Figure 2, Detail C.
0.100 in Minimum
(2.54 mm)
(2) Send all the recorded values to Bombardier Customer Support Engineering through SRPSA by e−mail at SRPSA@aero.bombardier.com.
(3) If the above measurement is within the limits, no further action is required.
MODEL BD−700−2A12 (BD−700) Basic Issue: Jul 22/2022 700−52−7511 Page 7 of 13
(4) If the above measurement is not within the limits, go to PART D.
E. PART D — Re−adjustment of Passenger Door Stops
(1) If any of the measurement obtained from PART C is not within the limits, do the door stops rigging to obtain the necessary values. Refer to Step 5 of BD700−A−J52−11−01−00AAA−275A−A.
(2) Do the adjust procedure for passenger−door closed proximity−sensor. Refer to BD700−A−J52−72−03−00AAA−271A−A.
(3) Do the function test procedure for passenger door handles. Refer to BD700−A−J52−11−05−02AAA−340A−A.
(4) Do the operational test procedure for the passenger door. Refer to BD700−A−J52−11−01−00AAA−320A−A.
(5) Do the procedure to pressurize the cabin to a differential pressure of 4.00 psid (27,58 kPa). Refer to BD700−A−J21−31−00−00AAA−364A−A.
(6) Send all the recorded values to Bombardier Customer Support Engineering through SRPSA by e−mail at SRPSA@aero.bombardier.com.
F. Testing No testing is required.
G. Close−out
(1) Remove all tools, equipment and unwanted materials from the aircraft.
H. Recording You can do each PART of this Service Bulletin independently. When any PART of this Service Bulletin is completed, make an entry in the aircraft log and send the attached Incorporation Notice to Bombardier Business Aircraft Customer Services (BBACS).
For information, corrections, comments and/or feedback regarding Service Bulletins released on the Customer Portal, please contact the Service Bulletin Group at the following email address:
bbad_SBgroup@aero.bombardier.com
3. MATERIAL INFORMATION A. Kit No kits required.
B. Parts No parts required.
MODEL BD−700−2A12 (BD−700) Basic Issue: Jul 22/2022 700−52−7511 Page 8 of 13
C. Material The materials that follow, or equivalent, are necessary to do this Service Bulletin.
These can be purchased from a local supplier. Bombardier Aviation does not pay for these consumable.
DESCRIPTION PART NO./NAME (SEE NOTE)
SPECIFICATION QUANTITY SUPPLIER Protective tape, polyurethane flame retardant (Patco 9425FR) 10−009 BAMS 553−007,Type VI As Necessary Code: A Cotter pin (MS24665−88) 05−030 MS24665 As Necessary Code: B Cotter pin (MS24665−304) 05−394 MS24665 As Necessary Code: B Lockwire (MS20995C32) (Alternate for safety cable) 05−005 NASM20995 As Necessary Code: B Safety cable kit (AS3510−0118K) 05−242 AS3510 As Necessary Code: B Safety cable kit (AS3510−0218K) 05−083 AS3510 As Necessary Code: B Safety cable kit (AS3510−0218C) 05−052 AS3510 As Necessary Code: B Sealant 06−002 MIL−PRF−81733, Type IV, Class 1, Grade A As Necessary Code: B Sealant 06−151 BAMS 552−002,Class B As Necessary Code: B NOTES: 1. Refer to the table that follows for each suppliers address listed by codes.
2. The Curing Time (CT), if applicable, for each consumable material is indicated with the description of each product.
MODEL BD−700−2A12 (BD−700) Basic Issue: Jul 22/2022 700−52−7511 Page 9 of 13
3. At time of release of this Service Bulletin, the information on the supplier was valid and accurate. In the event that this information has changed, the operator is encouraged to use the World Wide Web to find a local supplier.
SUPPLIERS ADDRESSES BY CODES Code: A Berry Global Inc.
51 Ballou Blvd, Bristol, RI − 02809 United States.
Code: B Commercially Available
4. For details refer to consumable reference code listed in AMP BD700−A−J51−31−00−00AAA−070A−A.
D. Publications No publications required.
MODEL BD−700−2A12 (BD−700) Basic Issue: Jul 22/2022 700−52−7511 Page 10 of 13
P9 P10 P11 P12 P1 P2 P3 P4 P5 P6 P7 P8 P21 P22 P23 P24 P20 P19 P18 P17 P16 P15 P14 P13 SB700−52−7511_001 A FWD A MODEL BD−700−2A12 (BD−700) Passenger Door Steps and Gaps Figure 1 Basic Issue: Jul 22/2022 700−52−7511 Page 11 of 13