Other document · Bombardier

No revision namedQ300 AMM TR 52-042 · 44 pages · 959 KB

© Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2018-0586, the docket of AD 2018-20-11. Not covered by OpenAirDocs’ CC0 dedication.

Docket FAA-2018-0586 (document 0006) · AD 2018-20-11

Manufacturer
Bombardier
Type
Temporary Revision
Number
Q300 52-042

A newer revision may exist than any OpenAirDocs knows of: check with the manufacturer.

On this page

Text · 44Partly OCR

Some pages are OCR from a scan. OCR can misread letters and numbers. © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2018-0586, the docket of AD 2018-20-11. Not covered by OpenAirDocs’ CC0 dedication.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '06a7df664f50c0bcc16120ac6c3cc2dbb0445e76b05680d52641a7c3990cc8bc'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

TEMPORARY REVISION 52−042 FILING INSTRUCTIONS: This Temporary Revision (TR52−042) replaces TR52−041. Put this Temporary Revision against pageblock AMM52−20−16−02, page

201.

Record the insertion of this Temporary Revision on the yellow RECORD OF TEMPORARY REVISIONS sheet at the front of this chapter.

DESCRIPTION: This Temporary Revision replaces TR52−041 to correct and clarify the access panels for replacement of bearings from their respective lever assemblies.

**ON A/C ALL FORWARD EMERGENCY EXIT DOOR − MAINTENANCE PRACTICES

1. General The maintenance procedures that follow are for the type I emergency exit door, type I emergency exit door seal and the type I emergency exit door bearings. The door is installed on the right hand side of the fuselage opposite to the passenger airstair door. The door incorporates a window and can be opened by either the internal or the external handles.

These procedures include:

– Removal and installation of the type I emergency exit door – Removal and installation of the type I emergency exit door seal – Removal and installation of the type I emergency exit door assist handle – Replacement of the bearings installed in the type I emergency exit door handle mechanism – Rigging of the type I emergency exit door operating mechanism – Inspection of the type I emergency exit door.

2. Removal/Installation Equipment and Materials:

– Force Gauge − 0 to 50 lbf (0 to 222.41 N) – Solvent – Plastic Scraper – Cloth, Lint−free – Adhesive − EC1357N or EC847 – Sealant − RTV 102 or RTV 732 A. Remove Forward Emergency Exit Door Refer to Figure 201.

DSERIES 300

AIRCRAFT MAINTENANCE MANUAL MASTER EFFECTIVITY: See First Page of TR# 52−042 52−20−16 Page 1 of 44 Apr 10/2018 TR# 52−042

TEMPORARY

REVISION

TEMPORARY

REVISION Series 300

CAUTION: DOOR WILL FALL FREELY FROM AIRCRAFT WHEN OPERATING HANDLE IS ACTUATED. ENSURE ADEQUATE SUPPORT IS AVAILABLE TO PREVENT DAMAGE TO DOOR STRUCTURE.

(1) Operate internal door handle (EMERGENCY PULL) to rotate the lift and latch shaft rollers in their respective followers.

NOTE: When type I emergency exit is opened for maintenance purposes, make sure that two persons are available to hold the weight of the door. The type I door is heavier than the type II exit doors and there is no counterbalance system.

NOTE: The maximum force necessary to fully operate the internal door handle is less than 40 lbf (177.92 N).

(2) Lift door upward and outward to clear opening in fuselage.

B. Install Forward Emergency Exit Door Refer to Figure 201.

(1) Move external operating handle to "fully open" position.

(2) Position door at door surround by locating upper and lower cam followers in their respective cams (AB) and (AC) and two spigots in guide cams (AD).

(3) Move external handle to "fully closed" position to close door, and return handle to recess.

(4) Make sure that the forward emergency exit door seal inflates correctly.

NOTE: If necessary, pressurize the door seal reservoir to 18 psi (124.1 kPa) at the charging valve in the wardrobe.

**ON A/C 100, 108, 116, 124, 131, 137, 143, 149, 154, 159, 164, 169, 174, 180, 182, 184, 186, 188, 190, 192, 194, 196, 198, 200, 202, 210, 216, 221, 224, 230, 232, 234, 240, 242, 244, 246, 248, 250, 252, 254, 256−257, 259, 261−262, 264, 266−267, 269, 271−272, 274, 276, 278−279, 281, 283−284, 286, 288, 290−291, 293, 295−296, 298, 300−301, 303, 305, 307, 309, 311, 313, 315, 319−320, 323, 325, 332, 334, 336, 338, 340, 342, 348, 350, 352, 354, 356, 358, 368, 370, 374−375, 379, 381, 385, 393, 395, 397, 399−402, 404−406, 408, 410, 412, 414−416, 420, 422−423, 438, 442−443, 451, 458, 462, 464, 466−467, 474, 481, 483, 485, 487, 489, 499, 503, 505, 508, 517, 519, 521, 523, 525, 527, 531, 533−534, 538−539, 543−546, 548−549, 552−557, 560−565, 567−571, 573−578, 580−583, 586−590, 592 Pre SB8−52−60 C. Remove Forward Emergency Exit Door Seal Refer to Figure 202

(1) Remove the emergency exit door from the aircraft (refer to para. 2. A).

(2) Put the door on a applicable work bench.

(3) Remove the door and window trim panels as necessary to get access to the pneumatic connector assembly.

(4) Loosen the clamp (4) on the air inlet hose (6) which connects the air valve (2) to the seal (1).

(5) Disconnect the air inlet hose (6) from the air valve (2) and remove the sleeve (5) and the clamp (4). Keep the removed hardware for the installation procedure.

(6) Put a protective plug on the open end of the elbow (3).

(7) Hold the seal (1) tightly with the fingers. Remove the air inlet assembly through the inlet hole.

DSERIES 300

AIRCRAFT MAINTENANCE MANUAL MASTER EFFECTIVITY: See First Page of TR# 52−042 52−20−16 Page 2 of 44 Apr 10/2018 TR# 52−042

TEMPORARY

REVISION

TEMPORARY

REVISION Series 300

(8) Remove the seal (1) from the seal retainer until the seal is free from the door.

(9) Discard the seal (1).

D. Install Forward Emergency Exit Door Seal Refer to Figure 202

(1) Examine the new seal (1) for the good condition.

(2) If necessary, clean the seal (1) with the solvent (Refer to AMM51−27−01).

(3) Dry the seal (1) with a lint free cloth before the solvent dries.

(4) Clean the used adhesive from the seal retainer with the plastic scraper.

(5) Clean the seal retainer with solvent (Refer to AMM51−27−01).

(6) Dry the seal retainer with a lint free cloth before the solvent dries.

(7) Apply adhesive to the bonding surface of the seal retainer.

(8) Install the air inlet assembly of the seal (1) through the air inlet hole.

(9) Compress the seal (1) with your fingers into the seal retainer.

NOTE: During installation, do not twist or stretch the seal.

(10) Connect the air inlet hose (6) to the air valve (2) as follows:

(a) Remove the protective plug from the open end of the elbow (3).

(b) Put the clamp (4) and the sleeve (5) on the air inlet hose (6).

(c) Install the air inlet hose (6) with the sleeve (5) to the air valve (2). This connects the air valve (2) to the seal (1).

(d) Tighten the clamp (4) on the air inlet hose (6).

(11) Install the emergency exit door (refer to para. 2. B).

(12) Do the pressurization leak test (Refer to AMM21−30−00).

**ON A/C 594−605, 607−611, 613−625, 627−636, 638−645, 647−648, 650−654, 656−660, 662−663, 667−672 and ON A/C 100, 108, 116, 124, 131, 137, 143, 149, 154, 159, 164, 169, 174, 180, 182, 184, 186, 188, 190, 192, 194, 196, 198, 200, 202, 210, 216, 221, 224, 230, 232, 234, 236, 238, 240, 242, 244, 246, 248, 250, 252, 254, 256−257, 259, 261−262, 264, 266−267, 269, 271−272, 274, 276, 278−279, 281, 283−284, 286, 288, 290−291, 293, 295−296, 298, 300−301, 303, 305, 307, 309, 311, 313, 315, 319−320, 323, 325, 332, 334, 336, 338, 340, 342, 348, 350, 352, 354, 356, 358, 365, 368, 370, 374−375, 379, 381, 385, 393, 395, 397, 399−402, 404−408, 410, 412, 414−416, 420, 422−423, 438, 442−443, 451, 458, 462, 464, 466−467, 474, 481, 483, 485, 487, 489, 491, 493, 495, 499, 503, 505, 508, 517, 519, 521, 523, 525, 527, 531−535, 538−539, 543−546, 548−549, 552−557, 560−565, 567−571, 573−578, 580−592 Post SB8−52−60 E. Remove Forward Emergency Exit Door Seal Refer to Figure 203

(1) Remove the emergency exit door from the aircraft (refer to para. 2. A).

(2) Put the door on a applicable work bench.

(3) Remove the door and window trim panels as necessary to get access to the pneumatic connector assembly.

(4) Loosen the clamp (3) on the air inlet hose (2) which connects the air valve to the seal (1).

(5) Disconnect the air inlet hose (2) from the coupling (4).

DSERIES 300

AIRCRAFT MAINTENANCE MANUAL MASTER EFFECTIVITY: See First Page of TR# 52−042 52−20−16 Page 3 of 44 Apr 10/2018 TR# 52−042

TEMPORARY

REVISION

TEMPORARY

REVISION Series 300

(6) Remove the clamp (3). Keep the removed hardware for the installation procedure.

(7) Put a protective plug on the open end of the coupling (4).

(8) Hold the seal (1) tightly with the fingers. Remove the air inlet assembly through the inlet hole.

(9) Remove the seal (1) from the seal retainer until the seal is free from the door.

(10) Discard the seal (1).

F. Install Forward Emergency Exit Door Seal Refer to Figure 203

(1) Examine the new seal (1) for the good condition.

(2) If necessary, clean the seal (1) with solvent (Refer to AMM51−27−01).

(3) Dry the seal (1) with a lint free cloth before the solvent dries.

(4) Clean the used adhesive from the seal retainer with the plastic scraper.

(5) Clean the seal retainer with solvent (Refer to AMM51−27−01).

(6) Dry the seal retainer with a lint free cloth before the solvent dries.

(7) Apply adhesive to the bonding surface of the seal retainer.

(8) Install the air inlet assembly of the seal (1) through the air inlet hole.

(9) Compress the seal (1) with your fingers into the seal retainer.

NOTE: During installation, do not twist or stretch the seal.

(10) Connect the air inlet hose (2) as follows:

(a) Remove the protective plug from the open end of the coupling (4).

(b) Put the clamp (3) on the air inlet hose (2).

(c) Install the air inlet hose (2) to the coupling (4). This connects the air valve to the seal (1).

(d) Tighten the clamp (3) on the air inlet hose (2).

(11) Install the emergency exit door (refer to para. 2. B).

(12) Remove all the tools, equipment and unwanted materials from the work area.

(13) Do the pressurization leak test (Refer to AMM21−30−00).

**ON A/C 438, 442, 466, 481, 483, 485 Post SB8−25−154 and ON A/C 527, 531, 553−554, 584−585, 594 Post SB8−25−282 G. Remove the assist handle from the type I emergency exit door as follows:

Refer to Figure 204

(1) Turn the nylon nuts (5) clockwise to remove the handle (1).

(2) Remove the bolts (2), washers (3), bushings (6), nylon nuts (5), washers (4) and the shims (7) from the handle (1) and door.

H. Install the assist handle from the type I emergency exit door as follows:

Refer to Figure 204

(1) Install the nylon nuts (5) with the washers (4), bushings (6), washers (3), bolt (2) and the shims (7).

(2) Tighten the bolt (2).

DSERIES 300

AIRCRAFT MAINTENANCE MANUAL MASTER EFFECTIVITY: See First Page of TR# 52−042 52−20−16 Page 4 of 44 Apr 10/2018 TR# 52−042

TEMPORARY

REVISION

TEMPORARY

REVISION Series 300

(3) Put the handle (1) on the nylon nuts (5).

(4) Turn the nylon nuts (5) counterclockwise to install the handle (1) to the door.

**ON A/C ALL I. Replacement of the bearing installed in the type I emergency exit door handle mechanism.

Refer to Figure 205

(1) Equipment and materials:

– 04−03 − Grease, aircraft and instrument, gear and actuator screw – 04−06 − Synthetic grease − General purpose, wide temperature range – 07−01 − F 13 Coating − Compound, corrosion preventive, (hard, soft film, moisture displacing) – 08−26 − Solvent − MPK (Methyl n−Propyl Ketone, by Eastman Chemical) – 14−02 − Wiper cloth − white cotton (lint free)

(2) Remove the type I emergency exit door (Refer to para 2.A).

(3) Remove the type I emergency exit door panel (Refer to AMM 25−22−05).

(4) There are no covers on panels (5), (6), (7), and (8). However, you may have to remove the panel cover (18) and brackets (19) for other bearings, if required (Refer to Figure 205, sheet 1 of 6).

WARNING: YOU MUST WEAR EYE PROTECTION WHEN YOU CUT THE COTTER PIN. WHEN YOU CUT THE COTTER PIN, PIECES CAN HIT YOUR EYES AND CAUSE INJURIES.

WARNING: YOU MUST WEAR EYE PROTECTION WHEN YOU CUT THE LOCKWIRE. WHEN YOU CUT THE LOCKWIRE, PIECES CAN HIT YOUR EYES AND CAUSE INJURIES.

(5) Replace the bearings (1) and (2) from the upper crank (4) as follows:

(a) Remove the upper crank (4) as follows:

1 Remove the nuts (11), washers (10) and bolts (9), (12) from the center shaft (13).

2 Remove the upper crank (4) from the type I emergency exit door (15).

3 If necessary, remove the washers (20) from the upper crank (4).

(b) Remove the bearings (1) from the housings (3) (Refer to AMM 20−19−02).

(c) Remove the bearings (2) from the housings (14) (Refer to AMM 20−19−02).

(d) If the bearings (1) and (2) are corroded, discard them.

(e) Clean the housings (3) and (14) with a lint free cloth moist in the solvent.

(f) Apply corrosion preventive compound (07−01) to the housings (3) and (14) (Refer to AMM 20−16−01).

(g) Apply grease (04−03) or (04−06) to the bearings (1) and (2).

(h) Install the bearings (1) and (2) to the housings (3) and (14) (Refer to AMM 20−19−02).

(i) If removed, install the washers (20) to the upper crank (4).

DSERIES 300

AIRCRAFT MAINTENANCE MANUAL MASTER EFFECTIVITY: See First Page of TR# 52−042 52−20−16 Page 5 of 44 Apr 10/2018 TR# 52−042

TEMPORARY

REVISION

TEMPORARY

REVISION Series 300

(j) Connect the upper crank (4) with the center shaft (13) with the bolts (9), (12), washers (10) and the nuts (11).

(6) Replace the bearings (16) and (17) from the lower crank (27) as follows:

(a) Remove the lower crank (27) as follows:

1 Remove the nuts (26), washers (25) and bolts (24) from the lower shaft

(28).

2 Remove the lower crank (27) from the type I emergency exit door (15).

3 If necessary, remove the washers (21) from the lower crank (27).

(b) Remove the bearings (16) from the housings (22) (Refer to AMM 20−19−02).

(c) Remove the bearings (17) from the housings (23) (Refer to AMM 20−19−02).

(d) If the bearings (16) and (17) are corroded, discard them.

(e) Clean the housings (22) and (23) with a lint free cloth moist in the solvent.

(f) Apply corrosion preventive compound (07−01) to the housings (22) and (23) (Refer to AMM 20−16−01).

(g) Apply grease (04−03) or (04−06) to the bearings (16) and (17).

(h) Install the bearings (16) and (17) to the housings (22) and (23) (Refer to AMM 20−19−02).

(i) If removed, install the washers (21) to the lower crank (27).

(j) Connect the lower crank (27) with the lower shaft (28) with the bolts (24), washers (25) and the nuts (26).

(7) Replace the bearing (30) from the handle assembly (31) as follows:

(a) Remove and discard the cotter pin (29).

(b) Remove the nut (44), washers (43), (41), bushing (42) and the bolt (40) from the rod assembly (39).

(c) Disconnect the rod assembly (39) from the handle assembly (31).

(d) Remove and discard the cotter pin (37).

(e) Remove the nut (36), washers (33), (35), bushing (34) and the bolt (32) from the handle assembly (31).

(f) Remove the handle assembly (31) from the support plate (38).

(g) Remove the bearing (30) from the handle assembly (31) (Refer to AMM 20−19−02).

(h) If the bearing (30) is corroded, discard it.

(i) Clean the handle assembly (31) and the support plate (38) with a lint free cloth moist in the solvent.

(j) Apply corrosion preventive compound (07−01) to the handle assembly (31) and the support plate (38) (Refer to AMM 20−16−01).

(k) Apply grease (04−03) or (04−06) to the bearing (30).

(l) Install bearing (30) to the handle assembly (31) (Refer to AMM 20−19−02).

(m) Install the handle assembly (31) to the support plate (38) with the bolt (32), washers (33), (35), bushing (34) and the nut (36).

DSERIES 300

AIRCRAFT MAINTENANCE MANUAL MASTER EFFECTIVITY: See First Page of TR# 52−042 52−20−16 Page 6 of 44 Apr 10/2018 TR# 52−042

TEMPORARY

REVISION

TEMPORARY

REVISION Series 300

(n) Safety the nut (36) with the new cotter pin (37).

(o) Install the rod assembly (39) to the handle assembly (31) with the bolt (40), washers (43), (41), bushing (42) and nut (44).

(p) Safety the nut (44) with the new cotter pin (29).

(8) Replace the bearings (45) and (46) from the lever assembly (52) as follows:

NOTE: Keep the removed hardware for the installation procedure.

(a) Remove and discard the cotter pin (50) from the nut (49).

(b) Remove the nut (49), bolt (47), washer (48) and the bushing (51).

(c) Disconnect the rod assemblies (61) and (62) from the lever assembly (52).

(d) Remove and discard the lockwire from the bolt (54).

(e) Remove the bolt (54), washers (58) and (111) and the bushing (59).

(f) Remove the nut (57), washer (56) and the bolt (55) to remove the housing

(53).

(g) Remove lever assembly (52) from the housing (53).

(h) If the bearings (45) and (46) are corroded, discard them.

(i) If necessary, remove the spacer (60) from the lever assembly (52).

(j) Clean the area and apply corrosion preventive compound (07−01) on the lever assembly (52) (Refer to AMM 20−16−01).

(k) If removed, install the spacer (60) to the lever assembly (52).

(l) Install new bearings (45) and (46) on the lever assembly (52).

(m) Apply grease (04−03) or (04−06) to the bearings (45) and (46) (Refer to AMM 20−16−01 and AMM 20−19−02).

(n) Install the housing (53) with the bolt (55), washer (56) and the nut (57).

(o) Install the bolt (54), washers (58) and (111) and the bushing (59) to connect the lever assembly (52) with the housing (53).

(p) Safety the bolt (54) with lockwire.

(q) Install rod assemblies (61) and (62) to the lever assembly (52) with the bolt

(47), washer (48), nut (49) and the bushing (51).

(r) Safety the nut (49) with the new cotter pin (50).

(9) Replace the bearings (63) and (64) from the lever assembly (67) as follows:

NOTE: Keep the removed hardware for the installation procedure.

(a) Remove and discard the cotter pins (78) from the nuts (77).

(b) Remove the nuts (77), bolts (75), washers (76) and the bushings (79).

(c) Disconnect the rod assemblies (65) and (66) from the lever assembly (67).

(d) Remove and discard the lockwire from the bolt (68).

(e) Remove the bolt (68), washers (69) and (81) and the bushing (70).

(f) Remove the nut (74), washer (73) and the bolt (72) to remove the housing

(80).

(g) Remove the lever assembly (67) from the housing (80).

DSERIES 300

AIRCRAFT MAINTENANCE MANUAL MASTER EFFECTIVITY: See First Page of TR# 52−042 52−20−16 Page 7 of 44 Apr 10/2018 TR# 52−042

TEMPORARY

REVISION

TEMPORARY

REVISION Series 300

(h) If the bearings (63) and (64) are corroded, discard them.

(i) If necessary, remove the spacer (71) from the lever assembly (67).

(j) Clean the area and apply corrosion preventive compound (07−01) on the lever assembly (67) (Refer to AMM 20−16−01).

(k) If removed, install the spacer (71) to the lever assembly (67).

(l) Install new bearings (63) and (64) on the lever assembly (67).

(m) Apply grease (04−03) or (04−06) to the bearings (63) and (64) (Refer to AMM 20−16−01 and AMM 20−19−02).

(n) Install lever assembly (67) to the housing (80) with the bolt (68), washers (69) and (81) and the bushing (70).

(o) Safety the bolt (68) with lockwire.

(p) Install the housing (80) with the bolt (72), washer (73) and the nut (74).

(q) Install rod assemblies (65) and (66) to the lever assembly (67) with the bolts

(75), washers (76), nuts (77) and the bushings (79).

(r) Safety the nuts (77) with the new cotter pins (78).

(10) Replace the bearings (86) and (87) from lever assemblies (88) and (89) as follows:

NOTE: Keep the removed hardware for the installation procedure.

(a) Remove the bolts (84), (102) and the washers (85), (103).

(b) Remove the cover plate (83).

(c) Remove and discard lockwire from the bolts (95) and (92).

(d) Remove bolts (95) and washers (96).

(e) Remove the bolt (92), washers (93), spacer (110) and the bushing (94).

(f) Remove the housing (91).

(g) Remove the lever assemblies (88) and (89) from the housing (91).

(h) Remove and discard the cotter pin (100) from the nut (99).

(i) Remove the nut (99), bolt (97), washers (98) and (112) and the bushings

(101).

(j) Disconnect the rod assembly (105) from the lever assembly (88).

(k) If the bearing (86) is corroded, discard it.

(l) Clean the area and apply corrosion preventive compound (07−01) on the lever assembly (88) (Refer to AMM 20−16−01).

(m) Install new bearing (86) on the lever assembly (88).

(n) Apply grease (04−03) or (04−06) to the bearing (86) (Refer to AMM 20−16−01 and AMM 20−19−02).

(o) Remove and discard the cotter pin (82) from the nut (109).

(p) Remove the nut (109), bolt (106), washer (108) and the bushing (107).

(q) Disconnect the rod assembly (104) from lever assembly (89).

(r) If the bearing (87) is corroded, discard it.

(s) Clean the area and apply corrosion preventive compound (07−01) on the lever assembly (89) (Refer to AMM 20−16−01).

DSERIES 300

AIRCRAFT MAINTENANCE MANUAL MASTER EFFECTIVITY: See First Page of TR# 52−042 52−20−16 Page 8 of 44 Apr 10/2018 TR# 52−042

TEMPORARY

REVISION

TEMPORARY

REVISION Series 300

(t) Install new bearing (87) on the lever assembly (89).

(u) Apply grease (04−03) or (04−06) to the bearing (87) (Refer to AMM 20−16−01 and AMM 20−19−02).

(v) Install the lever assemblies (88) and (89) and the housing (91) with the bolt

(92), washers (93), spacer (110) and the bushing (94).

(w) Connect the rod assembly (105) to the lever assembly (88) with the bolt (97), washers (98) and (112), nut (99) and the bushing (101).

(x) Safety the nut (99) with the new cotter pin (100).

(y) Connect the rod assembly (104) to the lever assembly (89) with the bolt (106), washer (108), nut (109) and the bushing (107).

(z) Safety the nut (109) with the new cotter pin (82).

(aa) Install the bolts (95) and the washers (96) to the housing (91).

(ab) Safety the bolts (95) and (92) with the lockwire.

(ac) Install the cover plate (83) with the bolts (84), (102) and the washers (85),

(103).

(11) Install the access panels (5), (6), (7), (8), (18) and (19), as applicable (Refer to SRM 52−30−11).

(12) Install the type I emergency exit door panel (Refer to AMM 25−22−05).

(13) Install the type I emergency exit door (Refer to para 2.B).

(14) Do an adjustment test of the type I emergency exit door (15) (Refer to Para 3).

(15) Open and close the door two times to make sure smooth movement with no interference to the liners.

(16) Do a handle preload check (Refer to Para 3.I).

(17) Remove all tools, equipment and unwanted materials from the work area.

DSERIES 300

AIRCRAFT MAINTENANCE MANUAL MASTER EFFECTIVITY: See First Page of TR# 52−042 52−20−16 Page 9 of 44 Apr 10/2018 TR# 52−042

TEMPORARY

REVISION

TEMPORARY

REVISION Series 300

dam03_5220162_001.dg, rt/vk, nov25/2010 AD AB N

FUSELAGE SKIN

0.030 in. (0.76 mm)

MINIMUM

DOOR SKIN SPIGOT

GUIDE CAM

PRESSURE

STOPLIFT CAM ROLLER

RETAINER SEAL

FILLET SEAL

ADHESIVE AC T

SERRATED

PLT & SHIM

PROXIMITY SENSOR TARGET GAP

ADJUSTING NUT LATCH CAM WITHOUT DOOR INSTALLED MIN. GAP 0.250 in.

(6.35 mm) WITH DOOR INSTALLED & LOCKED POSITION GAP 0.010 in − 0.020 in. (0.25 − 0.51 mm).

NOTE DSERIES 300

AIRCRAFT MAINTENANCE MANUAL FORWARD EMERGENCY EXIT − INSTALLATION AND RIGGING Figure 201 (Sheet 1 of 7) MASTER EFFECTIVITY: See First Page of TR# 52−042 52−20−16 Page 10 of 44 Apr 10/2018 TR# 52−042

TEMPORARY

REVISION

TEMPORARY

REVISION Series 300

CLOSED

STOP BOLT OPEN

STOP BOLT

LOWER TORQUE

TUBE ASSY

PUSH ROD LEVER

STOP FITTING A3

RIGGING PIN dam03_5220162_002.dg, rt, 24/02/04 DSERIES 300

AIRCRAFT MAINTENANCE MANUAL FORWARD EMERGENCY EXIT − INSTALLATION AND RIGGING Figure 201 (Sheet 2 of 7) MASTER EFFECTIVITY: See First Page of TR# 52−042 52−20−16 Page 11 of 44 Apr 10/2018 TR# 52−042

TEMPORARY

REVISION

TEMPORARY

REVISION Series 300

LEVER

PUSH ROD

RIGGING PIN

UPPER TORQUE

TUBE ASSY

PUSH ROD LEVER

RIGGING PIN STOP

FITTING CLOSED

STOP BOLT OPEN

STOP BOLT

PUSH ROD

LOWER TORQUE

TUBE ASSY

LEVER ASSY

PUSH ROD

RIGGING PIN

INNER DOOR HANDLE

IN CLOSED & LOCKED

POSITION

INNER DOOR HANDLE

IN OPENED POSITION A2 A1 A3 dam03_5220162_003.dg, rt/kmw, jun16/2011 F1 F2 DSERIES 300

AIRCRAFT MAINTENANCE MANUAL FORWARD EMERGENCY EXIT − INSTALLATION AND RIGGING Figure 201 (Sheet 3 of 7) MASTER EFFECTIVITY: See First Page of TR# 52−042 52−20−16 Page 12 of 44 Apr 10/2018 TR# 52−042

TEMPORARY

REVISION

TEMPORARY

REVISION Series 300