Text
From the PDF’s text layer: layout, tables and figures are lost. The PDF is the document.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'ec86eff49d374958530e5c008b9df595ec319a2cf0821410ed74a0b77f9b5310' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'ec86eff49d374958530e5c008b9df595ec319a2cf0821410ed74a0b77f9b5310' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
NONDESTRUCTIVE TESTING MANUAL Part 4 - Ultrasonic Part 4 Part 5 Part 6 Part 7 Part 8 Part 9 53- 61- 152 EFFECTIVITY: SEE PARAGRAPH 2 TR 53- 132 TEMPORARY REVISION 53 - 132 FILING INSTRUCTIONS: Insert this Temporary Revision facing TASK Part 4, 53- 61- 152.
Record the incorporation of this Temporary Revision on the yellow RECORD OF TEMPORARY REVISIONS sheet at the front of this volume.
Keep this Temporary Revision until Revision 45 incorporates this information into the Nondestructive Testing Manual.
DESCRIPTION: This Temporary Revision revises TASK Part 4, 53- 61- 152
ALTERNATE MEANS OF COMPLIANCE (AMOC) TO AD CF- 2001- 26R1 (SERVICE BULLETIN 601R- 53- 071), INSPECTION
OF THE UPPER AND LOWER WEBS AND DOUBLERS, AND AFT WEB OF THE REPAIR ENGINE SUPPORT BEAM AT FS640.00 to introduce a new calibration reference standard (CRS) and make other miscellaneous changes.
Part 4Page 1 of 23 Sep 15/23
NONDESTRUCTIVE TESTING MANUAL Part 4 − Ultrasonic Part 4 53−61−152 EFFECTIVITY: SEE PARAGRAPH 2 ALTERNATIVE MEANS OF COMPLIANCE (AMOC) TO AD CF−2001−26R1 (SERVICE BULLETIN 601R−53−071), INSPECTION OF THE UPPER AND LOWER WEBS AND DOUBLERS, AND AFT WEB OF THE REPAIR ENGINE SUPPORT BEAM AT FS640.00
1. General A. Function
(1) This inspection procedure is used to detect subsurface cracks in the engine support beam (ESB) at the following locations:
NOTE: The expected crack propagation is in the forward−to−aft direction at the top and bottom surfaces and in the up−to−down (vertical) direction on the side surfaces of the ESB.
− First outer forward row of fastener holes in the upper and lower webs covered by the inner rib flanges, along WL119.09 and WL111.12 at BL18.00 and BL0.00 at FS640.00 − First outer forward and aft (along FS640.00) rows of fastener holes in the upper and lower doublers or splice angles − horizontal flange covered by the external longitudinal stiffeners, along WL119.12 and WL111.09 at BL31.41 (upper doubler angle only), BL27.50, BL22.30, BL18.00, BL13.30, BL9.50, BL4.28, and BL0.00 at FS640.00.
− Lower row of fastener holes in the aft web at the upper doubler angle − vertical flange covered by the inner ribs at BL18.00 and BL0.00 at FS640.00 − Upper row of fastener holes in the aft web at the lower doubler − vertical flange covered by the inner ribs at BL18.00 and BL0.00 at FS640.00 − Upper and lower rows of fastener holes in the upper doubler − vertical flange covered by the external vertical stiffeners at BL27.50 and BL9.50 at FS640.00 − Upper and lower rows of fastener holes in the lower doubler − vertical flange covered by the external vertical stiffeners at BL27.50 and BL9.50 at FS640.00 − Upper and lower webs of the first two forward fasteners covered by the transversal angles along WL119.12 and WL111.09 between LBL38.00 and RBL38.00 at FS625.30.
NOTE: The inspection applies to both sides of the aircraft.
(2) The inspection procedure is applicable to aircraft with the post modifications listed in Table 1.
Table 1 − Aircraft Post Modification Configurations
MODIFICATION SUMMARY/REO KIT DRAWING/CONDITION REFER TOFIGURE NO.
TC601R16420 K601R35011 for Aircraft already repaired perREO 601R−53−61−345 Figure 2 TC601R16486 K601R35012 Figure 3 REO 601R−53−61−870 Replaces REO 601R−53−61−345 Figure 4
TR 53- 132 AWL 53-61-152 Page 2 of 23 Sep 15/23
NONDESTRUCTIVE TESTING MANUAL Part 4 − Ultrasonic Part 4 53−61−152 EFFECTIVITY: SEE PARAGRAPH 2 B. Reference Information For additional data that is necessary to do this inspection, refer to the manuals that follow:
− Nondestructive Testing Manual (NDTM), Part 1−General Information − Structural Repair Manual (SRM) − Aircraft Maintenance Manual (AMM).
This inspection must be done by a Level II or Level III ultrasonic qualified individual certified to an NDT Standard approved by the National Airworthiness Authority.
C. Location The engine support beam is located in Zone 310 (Refer to NDTM Part 1, 51−01−03).
D. Access
(1) Access to the inspection area is through the aft−equipment compartment door 311BB (Refer to Part 1, 51−01−04).
(2) It is recommended that the auxiliary power unit (APU) and the complete APU enclosure be removed to gain access to the engine support beam.
E. Parts Examined in This Procedure For aircraft repaired per TC601R16420 or kit K601R35011, refer to Table 2.
For aircraft repaired per TC601R16486 or kit K601R35012, refer to Table 3.
For aircraft repaired per REO 601R−53−61−870, refer to Table 4.
Table 2 − Part Identification Data for Aircraft Post TC601R16420 (Kit Drawing K601R35011)
ITEM NO. [1] DESCRIPTION DRAWING OR PARTNUMBER [2] MATERIAL SPECIFICATION 1 Upper web 601−35006−3 7075−T62 Al AlloyAlcd Sheet QQ−A−250/13 2 Upper doubler 601R−53−61−345−1 2024−T42 Al Alloy QQ−A−250/53 Lower doubler 601R−53−61−345−6 ySheet QQ−A−250/5 4 Lower web 601−35006−5 7075−T62 Al AlloyAlcd Sheet QQ−A−250/13 NOTE [1]: Parts that do not include an item number are not identified in Figure 2.
NOTE [2]: Numbers that do not include a dashed suffix are drawing numbers.
TR 53- 132 Page 3 of 23 Sep 15/23
NONDESTRUCTIVE TESTING MANUAL Part 4 − Ultrasonic Part 4 53−61−152 EFFECTIVITY: SEE PARAGRAPH 2 Table 2 − Part Identification Data for Aircraft Post TC601R16420 (Kit Drawing K601R35011) − (Continued) ITEM NO. [1] SPECIFICATIONMATERIALDRAWING OR PARTNUMBER [2]DESCRIPTION 5 Aft web 601−35006−9 6 Upper splice 601R350112−1 Upper splice 601R350112−2 7 Upper doubler 601R350111−1 2024 T42 Al AlloyUpper doubler 601R350111−2 2024−T42 Al AlloySheet QQ−A−250/5 8 Lower doubler 601R350113−1 Sheet Lower doubler 601R350113−2 9 Lower splice 601R350114−1 Lower splice 601R350114−2 NOTE [1]: Parts that do not include an item number are not identified in Figure 2.
NOTE [2]: Numbers that do not include a dashed suffix are drawing numbers.
Table 3 − Part Identification Data for Aircraft Post TC601R16486 (Kit Drawing K601R35012)
ITEM NO. [1] DESCRIPTION DRAWING OR PARTNUMBER [2] MATERIAL SPECIFICATION 1 Upper web 601−35006−3 7075−T62 Al AlloyAlcd Sheet QQ−A−250/13 2 Upper doubler 601R350115−1 2024−T42 Al AlloySheet QQ−A−250/5 3 Lower doubler 601R350116−1 2024−T42 Al AlloySheet QQ−A−250/5 4 Lower web 601−35006−5 7075−T62 Al AlloyAlcd Sheet QQ−A−250/13 5 Aft web 601−35006−9 2024−T42 Al AlloySheet QQ−A−250/5 NOTE [1]: Parts that do not include an item number are not identified in Figure 3 NOTE [2]: Numbers that do not include a dashed suffix are drawing numbers.
Table 4 − Part Identification Data for Aircraft with REO 601R53−61−870 Incorporated
ITEM NO. [1] DESCRIPTION DRAWING OR PARTNUMBER [2] MATERIAL SPECIFICATION 1 Upper web 601−35006−3 7075−T62 Al AlloyAlcd Sheet QQ−A−250/13 2 Upper doubler 601R−53−61−870−1 2024−T42 Al AlloySheet QQ−A−250/5
TR 53- 132 Page 4 of 23 Sep 15/23
NONDESTRUCTIVE TESTING MANUAL Part 4 − Ultrasonic Part 4 53−61−152 EFFECTIVITY: SEE PARAGRAPH 2 Table 4 − Part Identification Data for Aircraft with REO 601R53−61−870 Incorporated − (Continued) ITEM NO. [1] SPECIFICATIONMATERIALDRAWING OR PARTNUMBER [2]DESCRIPTION 3 Lower doubler 601R−53−61−870−6 2024−T42 Al AlloySheet QQ−A−250/5 4 Lower web 601−35006−5 7075−T62 Al AlloyAlcd Sheet QQ−A−250/13 5 Aft web 601−35006−9 2024−T42 Al AlloySheet QQ−A−250/5 NOTE [1]: Parts that do not include an item number are not identified in Figure 4.
NOTE [2]: Numbers that do not include a dashed suffix are drawing numbers.
2. Effectivity All aircraft post TC601R16420 (kit drawing K601R35011). TC601R16486 (kit drawing K601R35012), or REO 601R−53−61−870.
NOTE: NDTM Part 6, 53−61−152 and NDTM Part 9, 53−61−152 must be accomplished in order to complete the full inspection.
3. Tools and Equipment Use the items identified as follows, or their equivalent (Refer to NDTM Part 1, 51−20−04):
NOTE: Equivalent ultrasonic equipment may be used provided that it satisfies the requirements of this procedure and is capable of resolving the reference notch in the calibration standard at the required level of resolution.
− Ultrasonic Flaw Detector Sonatest Model: UFDS − Miniature angle beam transducer, 5.0 MHz frequency, 45 degrees refractive angle in aluminum, contact surface 0.250 in. (6.35 mm) by 0.375 in. (9.52 mm) VM Products Model: VM 7−121 − Coaxial cable (BNC to microdot) − Inspectech LTD Gorptech Industrial Ultrasonic Couplant Gel − MHI RJ Aviation calibration reference standard No. EXCM601R30039, containing electrical discharge machined (EDM) notches − High intensity light source.
4. Preparation and Cleaning A. Prepare the inspection area as follows:
(1) Identify the location of the area to be inspected.
(2) Open the aft−equipment compartment door 311BB to get access to the engine support beam (Refer to the AMM, 06−42−00−00).
TR 53- 132 Page 5 of 23 Sep 15/23
NONDESTRUCTIVE TESTING MANUAL Part 4 − Ultrasonic Part 4 53−61−152 EFFECTIVITY: SEE PARAGRAPH 2
(3) Remove the APU and the complete APU enclosure (Refer to the AMM, 49−11−01−000−801).
WARNING: MAKE SURE THAT THERE IS A GOOD FLOW OF CLEAN AIR AND SUFFICIENT FIRE PROTECTION. USE APPROVED BODY PROTECTION WHEN YOU USE SOLVENTS. ALL SOLVENTS ARE POISONOUS AND SOME ARE FLAMMABLE.
(4) Clean the inspection surfaces (Refer to the SRM, 51−26−00).
NOTE: It is not necessary to remove the finish from the parts unless they show deterioration or local damage.
(5) If the finish in the area to be inspected is damaged or deteriorated, remove the finish, complete the inspection, and then replace the finish (refer to the SRM, Chapter 51).
NOTE: It is not necessary to remove the finish from the parts unless it shows deterioration or local damage.
(6) If the finish in the area to be inspected is damaged or deteriorated, remove the finish (Refer to the SRM, chapter 51).
TR 53- 132 Page 6 of 23 Sep 15/23
NONDESTRUCTIVE TESTING MANUAL Part 4 − Ultrasonic Part 4 53−61−152 EFFECTIVITY: SEE PARAGRAPH 2
5. Inspection for Subsurface Cracks Initiating From the First Outer Row of Fasteners of the Repair in the 0.032−in (0.81−mm) Thick Section of the Upper and Lower Webs Along WL119.12 and WL111.09 at BL0.00, FS640.00 and Inspection of the First Two Forward Fasteners Aft of FS625.30 at BL0.00 and BL4.28 A. Equipment Calibration Refer to Figure 1.
(1) Calibrate the ultrasonic equipment as follows:
(a) Connect the transducer (VM 7−121) to the ultrasonic instrument with the coaxial cable.
(b) Turn the power ON and set the instrument to pulse−echo test mode and 5 MHz test frequency.
(c) Apply an even layer of couplant gel on the 0.032−in (0.813−mm) thick section of the −3 web adjacent to the −4 and −5 angles (0.62−in (15.75−mm) edge distance side) of reference standard EXCM601R30039.
(d) Do the instrument calibration on the reference standard as follows:
1 Place the front of the transducer against the −4 angle so that the sound beam is directed at EDM notch A (Notch Echo A (NEA)) (Refer to Transducer Placement 1 in Figure 1). Manipulate the transducer by swiveling the transducer toward and away from the NEA to obtain a maximized amplitude signal.
2 Adjust the instrument GAIN control to obtain a 100% full screen height (FSH) signal from NEA.
3 Use the instrument DELAY and RANGE controls to set the leading edge of the reflection signal from NEA at 20% of the horizontal limit on the baseline.
TR 53- 132 Page 7 of 23 Sep 15/23
NONDESTRUCTIVE TESTING MANUAL Part 4 − Ultrasonic Part 4 53−61−152 EFFECTIVITY: SEE PARAGRAPH 2 rnd5361152_027.dg, lr, 01/11/05
0.62 in.
(15.75 mm)
0.62 in.
(15.75 mm)
TRANSDUCER PLACEMENT 1 A B
TRANSDUCER PLACEMENT 2 −3 WEB
CHEM MILL LINE (REF)
0.050 in.
(1.27 mm)
0.25 in.
(6.35 mm) −4 ANGLE −5 ANGLE −3 WEB
EDM NOTCH NEA
CRT DISPLAY IP EFH IP NEB TRANSDUCER PLACEMENT 2 50 1000 TRANSDUCER PLACEMENT 1 50 1000 NOTES 50 100
SIGNAL AMPLITUDE 50 100
SIGNAL AMPLITUDE IP = Initial pulse.
NEA = Notch echo from EDM notch A.
CRT DISPLAY
0.032 in.
(0.81 mm) (4 PLACES) NEB = Notch echo from EDM notch B.
EFH = Echo from fastener hole.
Calibration Reference Standard EXCM601R30039 and Transducer Placement, and CRT Displays of Calibration Notch Signals Figure 1
TR 53- 132 Page 8 of 23 Sep 15/23
NONDESTRUCTIVE TESTING MANUAL Part 4 − Ultrasonic Part 4 53−61−152 EFFECTIVITY: SEE PARAGRAPH 2B . Inspection Procedure Refer to Figure 1 and Figure 2, Figure 3, or Figure 4.
NOTE: For parts to be examined, refer to Table 2, Table 3, or Table 4.
The numbers in the brackets [ ] correspond to the item numbers found in Figure 2, Figure 3, and Figure 4 as well as Table 2, Table 3, and Table 4.
A nonrelevant indication from the fastener hole may or may not appear when the sound beam is in−line with the center of the fastener, but the indication will always appear closer to the initial pulse or left side of the CRT screen than a relevant discontinuity indication.
(1) Inspect the first outer forward row of fasteners under the repair doublers [2] and [3] (for K601R35012 and REO 601R53−61−870) and [2], [3], [8], and [9] (for K601R35011) in the 0.032−in (0.81−mm) thick section of the upper web [1] and lower web [4] along WL119.12 and WL111.09 at BL0.00 as follows:
NOTE: There are a total of two fastener locations symbolized as that require inspection. One is located at the lower web and one is located at the upper web. Refer to Sheets 1 and 2 of Figure 2, Figure 3, or Figure 4.
Inspection of the upper and lower webs under the repair doublers are performed internally via the lightening holes in the aft web.
(a) After calibration as outlined in paragraph 5.A., apply an even layer of couplant gel on the 0.032−in (0.81−mm) thick section of the upper web [1] and lower web [4] adjacent to the edge of the upper and lower rib flanges of the first forward outer row of fasteners at BL0.00, approximately at FS633.00.
(b) Couple the transducer to the upper web [1] with the front of the transducer against the rib flange at BL0.00. Scan both sides of the forward outer fastener with a slight swivel movement towards and away from the fastener.
NOTE: Use the edge of the rib flange as a transducer guide.
(c) Repeat step 5.B.(1)(b) for the fastener identified with the symbol on the lower web [4]at BL0.00.
(d) Note all relevant indications 50% FSH or greater and its location on the part.
NOTE: Ensure the indication is not from the fastener hole.
(2) Inspect the first two forward fasteners of the upper web [1] and lower web [4] aft of FS625.30 along BL0.00 and BL4.28 as follows:
NOTE: There are a total of 12 fastener locations symbolized as that require inspection. The lower web has 6 of the fasteners (2 fasteners each at BL0.00, LBL4.28, and RBL4.28). The other 6 fasteners are on the upper web (2 fasteners each at BL0.00, LBL4.28, and RBL4.28). Refer to Sheets 1 and 2 of Figure 2, Figure 3, or Figure 4 for the modification configuration applicable to the aircraft to be inspected.
Inspection of the upper and lower webs for the two forward fasteners aft of FS625.30 are performed externally.
(a) After calibration as outlined in paragraph 5.A., apply an even layer of couplant gel on the 0.032−in (0.81−mm) thick section of the upper web [1] and lower web [4] adjacent to the edge of the upper and lower longitudinal stiffener angle flanges of the first two forward fasteners along BL0.00, LBL4.28 and RBL4.28, aft of FS625.30.
TR 53- 132 Page 9 of 23 Sep 15/23
NONDESTRUCTIVE TESTING MANUAL Part 4 − Ultrasonic Part 4 53−61−152 EFFECTIVITY: SEE PARAGRAPH 2 rnd5361152_005.dg, lr, 02/11/05
VIEW LOOKING DOWN
ON TOP SURFACE OF ENGINE SUPPORT BEAM
INSPECTSYMBOL LEGEND
6. Upper splice.
7. Upper doubler.
Inspect upper web via lightening holes in the aft web both sides of these fasteners.
Inspect upper doubler and/or splice angle Inspect upper web externally both sides Inspect upper doubler or splice (horizontal flange) externally both sides of these LBL36.20 LBL9.50 BL0.00 LBL4.28LBL31.41 LBL27.50 LBL22.30 LBL18.00 LBL13.30 FS
625.30 FS
640.00
0.063 in. (1.60 mm)
THICKNESS
SECTION OF WEB
CHEM MILL LINE (REF)
0.050 in. (1.27 mm)
THICKNESS SECTION OF WEB 0.032 in. (0.81 mm)THICKNESS
SECTION OF WEB
CHEM MILL LINE (REF) 1 7
1. Upper web.
2. Upper doubler (existing 6 2 (horizontal flange) externally both sides of A of these fasteners.
GREO 601R−53−61−345−1).
A
TYPICAL TRANSDUCER
PLACEMENT AND MOVEMENT
BOTH SIDES OF FASTENER
TO BE INSPECTED
TRANSDUCER these fasteners.
fasteners.
Inspection Locations of the Engine Support Beam for Aircraft Post TC601R16420 (Repair Kit K601R35011) Figure 2 (Sheet 1)
TR 53- 132 Page 10 of 23 Sep 15/23
NONDESTRUCTIVE TESTING MANUAL Part 4 − Ultrasonic Part 4 53−61−152 EFFECTIVITY: SEE PARAGRAPH 2
VIEW LOOKING UP
ON LOWER WEB OF ENGINE SUPPORT BEAM LEGEND
8. Lower doubler.
3. Lower doubler (existing LBL18.00 LBL9.50 BL0.00LBL13.30 LBL4.28 FS
625.30 FS
640.00 LBL27.50 LBL22.30
INSPECTSYMBOL Inspect lower web via lightening holes in the aft web both sides of these fasteners.
Inspect lower doubler (horizontal flange) Inspect lower web externally both sides
0.032 in. (0.81 mm)
THICKNESS
SECTION OF WEB
0.050 in. (1.27 mm)
THICKNESS
SECTION OF WEB 4 9
0.063 in. (1.60 mm)
THICKNESS
SECTION OF WEB rnd5361152_007.dg, lr, 02/11/05 8
4. Lower web.
9. Lower splice.
3 Inspect lower doubler or splice (horizontal flange) externally both sides of these GREO 601R−53−61−345−6).
of these fasteners.
externally both sides of these fasteners.
B
TYPICAL TRANSDUCER
PLACEMENT AND MOVEMENT
BOTH SIDES OF FASTENER
TO BE INSPECTED
TRANSDUCER B fasteners.
Inspection Locations of the Engine Support Beam for Aircraft Post TC601R16420 (Repair Kit K601R35011) Figure 2 (Sheet 2)
TR 53- 132 Page 11 of 23 Sep 15/23
NONDESTRUCTIVE TESTING MANUAL Part 4 − Ultrasonic Part 4 53−61−152 EFFECTIVITY: SEE PARAGRAPH 2 rnd5361152_006.dg, lr, 02/11/05
INSPECTSYMBOL Inspect aft web (covered by inner ribs) via lightening holes in the aft web both sides of these fasteners.
Inspect lower doubler angle (vertical flange) Inspect upper doubler angle (vertical flange) LEGEND
2. Upper doubler (existing REO 601R−53−61−345−1).
7. Upper doubler.
LBL36.20 LBL31.41 LBL27.50 LBL22.30 LBL18.00 LBL13.30 LBL9.50 LBL4.28 BL0.00 WL
119.12 WL
111.09 2 9 6 58
8. Lower doubler.
3. Lower doubler (existing
9. Lower splice.
6. Upper splice.
7 3 externally both sides of these fasteners.
externally both sides of these fasteners.
5. Aft web.
REO 601R−53−61−345−6).
C
TYPICAL TRANSDUCER
PLACEMENT AND MOVEMENT
BOTH SIDES OF FASTENER
TO BE INSPECTED
TRANSDUCER C
VIEW LOOKING FORWARD AT FS640.00 ON AFT WEB Inspection Locations of the Engine Support Beam for Aircraft Post TC601R16420 (Repair Kit K601R35011) Figure 2 (Sheet 3)
TR 53- 132 Page 12 of 23 Sep 15/23