Copy · CFM Service Bulletin LEAP-1A-72-0460R0 Dated 4-1-2022 · 17 pages

© CFM International. Filed by the FAA in regulations.gov docket FAA-2022-0877; AD 2022-15-04 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Text

From the PDF’s text layer: layout, tables and figures are lost. The PDF is the document.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '6ab08f7c0d645de3c95a1b95f443b80d31f23cac8b6d6906bfbbd4e7794dd7ec'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

LEAP - 1A - 72 - 00 - 0460 - 01A - 930A - D HIGH

PRESSURE

TURBINE ROT OR

ASSEMBL Y (72 - 52 -

00) -

INSPECTION OF HPT MODULE T O

DETERMINE HPT ROT OR

INTERST AGE SEAL AND HPT ROT OR ST AGE 2 DISK

REPLACEMENT

SERVICE

BULLETIN T able of contents

1.

REVISION

INFORMA TION .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

2.

SUMMAR Y .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

3 A.

Reason .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

3.

PLANNING

INFORMA TION .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

3 A.

Applicability .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

3 B.

Concurrent requirements .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

3 C.

Reason .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

3 D.

Description .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

4 E.

Compliance .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

4 F .

Approval .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

4 G.

Manpower .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

4 H.

W eight and balance .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

4 I.

Electrical load data .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

4 J.

Software accomplishment summary .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

4 K.

Referenced documentation .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

4 L.

Documentation af fected .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

5 M.

Industry support information .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

5 N.

Interchangeability .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

4.

MA TERIAL

INFORMA TION .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

5.

ACCOMPLISHMENT

INSTRUCTIONS .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

5 A.Engine Inspection Instructions .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

5 B.In - Shop Disassembly , Inspection, and Removal .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

6.

ADDITIONAL

INFORMA TION .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

17 A.

Additional information .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

17 List of tables T able:

References .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

2 T able 1:

Engine Inspection Threshold for the HPT Rotor Interstage Seal .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

5 T able 2:

Engine Inspection Threshold for the HPT Rotor Stage 2 Disk .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

6 T able 3:

CFM Contact Information .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

17 LEAP - 1A - 72 - 00 - 0460 - 01A - 930A - D Page 1/ 17 Issue 001 - 00 - 2022 - 04 - 01 © CFM

PROPRIET AR Y

INFORMA TION:

Subject to the restrictions on the media.

LEAP - 1A - 72 - 00 - 0460 - 01A - 930A - D List of figures Figure 1 (Sheet 1/2):

HPT Rotor Assembly Piece - part Inspection .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

9 Figure 1 (Sheet 2/2):

HPT Rotor Assembly Piece - part Inspection .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

10 Figure 2:

Engine Threshold Removal Calculation .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

1 1 Figure 3 (Sheet 1/2):

Stage 2 HPT Nozzle Assembly Location .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

12 Figure 3 (Sheet 2/2):

Stage 2 HPT Nozzle Assembly Location .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

13 Figure 4:

Shop Actions to Determine Serviceability of HPT Hardware .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

14 Figure 5 (Sheet 1/2):

HPT Stator Stationary Seal Location .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

15 Figure 5 (Sheet 2/2):

HPT Stator Stationary Seal Location .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

16 CFM

PROPRIET AR Y

INFORMA TION The information contained in this document is CFM proprietary information and is disclosed in confidence.

It is the property of CFM and shall not be used, disclosed to others or reproduced without the express written consent of CFM, including, but without limitation, it is not to be used in the creation, manufacture, development, or derivation of any repairs, modifications, spare parts, design, or configuration changes or to obtain F AA or any other government or regulatory approval to do so.

If consent is given for reproduction in whole or in part, this notice and the notice set forth on each page of this document shall appear in any such reproduction in whole or in part.

The information contained in this document may also be controlled by U.S.

export control laws.

Unauthorized export or re - export is prohibited.

References T able:

References T echnical Publication LEAP - 1A - 05 - 1 1 - 00 - 01A - 040A - C LEAP - 1A - 72 - 00 - 00 - 01A - 530A - C LEAP - 1A - 72 - 00 - 02 - 51A - 52AA - C LEAP - 1A - 72 - 00 - 53 - 01A - 663B - C LEAP - 1A - 72 - 53 - 00 - 01A - 530A - C LEAP - 1A - 72 - 53 - 00 - 01A - 710A - C LEAP - 1A - 72 - 52 - 00 - 01A - 530A - C LEAP - 1A - 72 - 52 - 00 - 01A - 710A - C LEAP - 1A - 72 - 54 - 00 - 01A - 530A - C LEAP - 1A - 72 - 54 - 00 - 01A - 710A - C Management information Manufacturer recommendation:

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

Recommended LEAP - 1A - 72 - 00 - 0460 - 01A - 930A - D Page 2/ 17 Issue 001 - 00 - 2022 - 04 - 01 © CFM

PROPRIET AR Y

INFORMA TION:

Subject to the restrictions on the media.

LEAP - 1A - 72 - 00 - 0460 - 01A - 930A - D T ask type:

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

Inspection Original issue date:

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

2022 - 04 - 05

1.

REVISION

INFORMA TION Not Applicable.

2.

SUMMAR Y A.

Reason T o reduce significant events.

3.

PLANNING

INFORMA TION A.

Applicability This Service Bulletin is applicable to:

• Engine type:

LEAP - 1A

• Engine model(s):

LEAP - 1A23,LEAP - 1A24,LEAP - 1A24E1,LEAP - 1A26,LEAP - 1A26CJ,LEAP - 1A26E1,LEAP - 1A29,LEAP - 1A29CJ,LEAP - 1A30,LEAP - 1A32,LEAP - 1A33,LEAP - 1A33B2,LEAP - 1A35A This Service Bulletin is applicable to these LEAP - 1A engines:

• LEAP - 1A engines, serial numbers 598 - 280, 598 - 283, 598 - 284, 598 - 291, 598 - 300, 598 - 302, 598 - 327, 598 - 572, 598 - 629, 598 - 648, 598 - 659, 598 - 667, 598 - 909, and 599 -

192.

These serial numbers are the best available data.

Engine models are defined as follows:

Group 1:

LEAP - 1A30, LEAP - 1A32, LEAP - 1A33, LEAP - 1A33B2, and LEAP - 1A35A.

Group 2:

LEAP - 1A23, LEAP - 1A24, LEAP - 1A24E1, LEAP - 1A26, LEAP - 1A26CJ, LEAP - 1A26E1, LEAP - 1A29, and LEAP - 1A29CJ.

The high pressure turbine (HPT) rotor interstage seals and HPT rotor stage 2 disks listed in T able 1 and T able 2 are af fected by this Service Bulletin.

B.

Concurrent requirements None.

C.

Reason

(1) Objective:

T o reduce significant events.

(2) Condition:

A LEAP - 1A in - service engine has experienced higher than anticipated operating temperatures on the HPT rotor , resulting in distress to the HPT rotor interstage seal and potential creep.

(3) Cause:

More open operating clearances contributed to the HPT rotor interstage seal operating at elevated temperatures.

(4) Improvement and inspection:

This Service Bulletin provides a list of af fected population of 14 LEAP - 1A engines that have potential impact to chapter 05 life of HPT rotor interstage seal and HPT rotor stage 2 disk and required inspection procedures to determine their serviceability .

LEAP - 1A - 72 - 00 - 0460 - 01A - 930A - D Page 3/ 17 Issue 001 - 00 - 2022 - 04 - 01 © CFM

PROPRIET AR Y

INFORMA TION:

Subject to the restrictions on the media.

LEAP - 1A - 72 - 00 - 0460 - 01A - 930A - D

(5) Substantiation:

Substantiation is by analysis.

D.

Description This Service Bulletin provides a list of af fected population of 14 LEAP - 1A engines that had non - synchronous vibrations in the past and could have an impact on the HPT rotor interstage seal and HPT rotor stage 2 disk low cycle fatigue (LCF) life due to higher HPT rotor interstage seal and HPT stator stationary seal operating clearances.

This Service Bulletin recommends engine inspection prior to thresholds defined in T able 1 and T able 2 for inspecting the HPT module for stage 2 HPT nozzle assembly honeycomb and HPT stator stationary seal honeycomb rub depths to determine if replacement of the HPT rotor interstage seal and HPT rotor stage 2 disk is required.

E.

Compliance Category 2 CFM recommends that you do this Service Bulletin at next shop visit but before inspection thresholds specified in T able 1 for the HPT rotor interstage seal and in T able 2 for the HPT rotor stage 2 disk.

Impact A This recommendation is to address a condition that may af fect Flight Safety .

NOTE:

Stage 2 nozzle honeycomb seal and HPT stator stationary honeycomb seal on each affected engine must be inspected before the most limiting thresholds between T able 1 for the HPT rotor interstage seal and T able 2 for the HPT rotor stage 2 disk.

NOTE:

This Service Bulletin can be done in shop.

This Service Bulletin is of fered to improve the reliability or performance of your CFM product, or to help prevent the occurrence of the event or condition described in this Service Bulletin.

If the operator elects not to participate in the bulletin, that decision will be taken into consideration by CFM in evaluating future product performance issues that may arise in the operator ’ s fleet.

F .

Approval The technical content of this Service Bulletin is approved by the F AA and under the Authority of DOA No.

EASA.21J.086.

G.

Manpower After you get access to the HPT module, you will need approximately 6 man - hours to do the inspection portion of this Service Bulletin.

H.

W eight and balance W eight and balance are not changed.

I.

Electrical load data Not Applicable.

J.

Software accomplishment summary Not Applicable.

K.

Referenced documentation LEAP - 1A - 72 - 00 - 0460 - 01A - 930A - D Page 4/ 17 Issue 001 - 00 - 2022 - 04 - 01 © CFM

PROPRIET AR Y

INFORMA TION:

Subject to the restrictions on the media.

LEAP - 1A - 72 - 00 - 0460 - 01A - 930A - D CFM LEAP - 1A Engine Shop Manual (ESM), CFM - TP - 610 SM.20 L.

Documentation affected None.

M.

Industry support information None.

N.

Interchangeability Not Applicable.

4.

MA TERIAL

INFORMA TION List of material sets Not Applicable.

List of support equipment Not Applicable.

List of supplies Not Applicable.

List of spares Not Applicable.

List of removed spares Not Applicable.

5.

ACCOMPLISHMENT

INSTRUCTIONS A.

Engine Inspection Instructions

(1) The inspection threshold for each ESN is listed in T able 1 for the HPT rotor interstage seal (1, Figure 1 ) (SIN:

157B0) and T able 2 for the HPT rotor stage 2 disk

(3) (SIN:

158B0).

The LEAP - 1A engine must be inspected before this threshold.

T able 1:

Engine Inspection Threshold for the HPT Rotor Interstage Seal ESN Current Engine Rating HPT Rotor Interstage Seal S/N Inspection Threshold for Group 1 (CSN) Inspection Threshold for Group 2 (CSN) 598 - 280 1A26 WESF2870 4,000 1 1,100 598 - 283 1A26 WESF3374 4,000 1 1,100 598 - 284 1A26 WESF3926 4,000 1 1,100 598 - 291 1A26 WESF3381 2,200 1 1,100 598 - 300 1A26 WESF3563 4,000 1 1,100 to be continued ...

LEAP - 1A - 72 - 00 - 0460 - 01A - 930A - D Page 5/ 17 Issue 001 - 00 - 2022 - 04 - 01 © CFM

PROPRIET AR Y

INFORMA TION:

Subject to the restrictions on the media.

LEAP - 1A - 72 - 00 - 0460 - 01A - 930A - D ESN Current Engine Rating HPT Rotor Interstage Seal S/N Inspection Threshold for Group 1 (CSN) Inspection Threshold for Group 2 (CSN) 598 - 302 1A32 WESF3383 4,000 1 1,100 598 - 327 1A26 WESF3932 4,000 1 1,100 598 - 572 1A26 WESF6688 4,000 1 1,100 598 - 629 1A32 FIA15TGA 1 1,100 1 1,100 598 - 648 1A26 XAE018BJ 700 1 1,100 598 - 659 1A26 WESF7141 4,000 1 1,100 598 - 667 1A26 XAE013BJ 700 1 1,100 598 - 909 1A26 FIA18FMH 3,300 1 1,100 599 - 192 1A26 WESF8994 700 1 1,100 NOTE:

Group 1:

LEAP - 1A30, LEAP - 1A32, LEAP - 1A33, LEAP - 1A33B2, and LEAP - 1A35A.

Group 2:

LEAP - 1A23, LEAP - 1A24, LEAP - 1A24E1, LEAP - 1A26, LEAP - 1A26CJ, LEAP - 1A26 E1, LEAP - 1A29, and LEAP - 1A29CJ.

T able 2:

Engine Inspection Threshold for the HPT Rotor Stage 2 Disk ESN Current Engine Rating HPT Rotor Stage 2 Disk S/N Inspection Threshold for Group 1 (CSN) Inspection Threshold for Group 2 (CSN) 598 - 280 1A26 TMT3NC79 8,900 9,900 598 - 283 1A26 TMT3NC84 8,900 9,900 598 - 284 1A26 TMTF0548 8,900 9,900 598 - 291 1A26 TMT3NC82 8,200 9,900 598 - 300 1A26 TMT10M3T 8,900 9,900 598 - 302 1A32 TMT3NC75 8,900 9,900 598 - 327 1A26 TMTF0534 8,900 9,900 598 - 572 1A26 TMT124P0 8,900 9,900 598 - 629 1A32 TMT1 1C51 8,900 9,900 598 - 648 1A26 TMT124NP 6,300 9,900 598 - 659 1A26 TMT12D31 8,900 9,900 598 - 667 1A26 TMT12HK7 6,300 9,900 598 - 909 1A26 TMT14EFH 8,200 9,900 599 - 192 1A26 TMT13RLL 6,300 9,900 LEAP - 1A - 72 - 00 - 0460 - 01A - 930A - D Page 6/ 17 Issue 001 - 00 - 2022 - 04 - 01 © CFM

PROPRIET AR Y

INFORMA TION:

Subject to the restrictions on the media.

LEAP - 1A - 72 - 00 - 0460 - 01A - 930A - D NOTE:

Group 1:

LEAP - 1A30, LEAP - 1A32, LEAP - 1A33, LEAP - 1A33B2, and LEAP - 1A35A.

Group 2:

LEAP - 1A23, LEAP - 1A24, LEAP - 1A24E1, LEAP - 1A26, LEAP - 1A26CJ, LEAP - 1A26 E1, LEAP - 1A29, and LEAP - 1A29CJ.

(2) If an engine re - rating has not occurred, use the thresholds from T able 1 and T able 2 as appropriate.

In case of engine re - rating from Group 2 to Group 1 or vice - versa, use the Miner's rule to calculate the modified inspection threshold for the HPT rotor interstage seal

(1) (SIN:

157B0) and HPT rotor stage 2 disk

(3) (SIN:

158B0).

Threshold values from T able 1 or T able 2 must be used appropriately to calculate new threshold.

Refer to the LEAP - 1A ESM, 05 - 1 1 - 00,

DESCRIPTION ( Refer to:

LEAP - 1A - 05 - 1 1 - 00 - 01A - 040A - C ) and flowchart 1 in Figure 2 .

B.

In - Shop Disassembly , Inspection, and Removal

(1) Remove the core module assembly (SIN:

00104) from the engine assembly (SIN:

00002).

Refer to the LEAP - 1A ESM, 72 - 00 - 00,

DISASSEMBLE

PROCEDURE ( Refer to:

LEAP - 1A - 72 - 00 - 00 - 01A - 530A - C ).

(2) Remove the HPT rotor assembly (SIN:

15000, Figure 1 ) from the core module assembly (SIN:

00104).

Refer to the LEAP - 1A ESM, 72 - 00 - 02, REMOVE ENGINE

MODULAR

SECTION ( Refer to:

LEAP - 1A - 72 - 00 - 02 - 51A - 52AA - C ).

(3) Do an inspection of the honeycomb of the stage 2 HPT nozzle assembly (1, Figure 3 ) (SIN:

17300) as specified in below criteria.

Also, refer to Flowchart 2 in Figure 4 which explains the disposition steps and do as follows:

(a) T ake measurements at eight equally spaced locations circumferentially , which include approximately deepest rub location.

Refer to Figure 3 for more information and the criteria that follow:

1 Maximum permitted individual groove depth

0.070 inch

(1.78 mm) 2 Maximum permitted average depth of all grooves

0.049 inch

(1.24 mm) 3 Maximum permitted individual groove width is

0.225 inch

(5.72 mm) 4 There must be four annular wear grooves separated by a minimum of

1.0 complete cell.

There must be

1.0 complete cell on the forward and aft ends of the honeycomb.

5 Report the results to CFM.

Refer to paragraph

6.,

ADDITIONAL

INFORMA TION for CFM contact information.

(b) If the stage 2 HPT nozzle assembly (1, Figure 3 ) (SIN:

17300) honeycomb inspection meets all above criteria, no action is necessary on the stage 2 HPT nozzle assembly

(1) (SIN:

17300), HPT rotor interstage seal (1, Figure 1 ) (SIN:

157B0), and HPT rotor stage 2 disk

(3) (SIN:

158B0).

(c) If the stage 2 HPT nozzle assembly (1, Figure 3 ) (SIN:

17300) honeycomb fails to meet any of the above criteria, do as follows:

1 Replace the stage 2 HPT nozzle assembly

(1) (SIN:

17300) honeycomb.

Refer to the LEAP - 1A ESM, 72 - 00 - 53,

REPLACEMENT OF

INTERST AGE SEAL ( Refer to:

LEAP - 1A - 72 - 00 - 53 - 01A - 663B - C ) as follows:

a If the stage 2 HPT nozzle assembly (1, Figure 3 ) (SIN:

17300) honeycomb replacement is not possible, replace the stage 2 HPT nozzle assembly

(1).

Removal and installation instructions have not changed.

Refer to the LEAP - 1A ESM, 72 - 53 - 00,

DISASSEMBLE

PROCEDURE ( Refer to:

LEAP - 1A - 72 - 53 - 00 - 01A - 530A - C ) and

ASSEMBLE

PROCEDURE ( Refer to:

LEAP - 1A - 72 - 53 - 00 - 01A - 710A - C ).

LEAP - 1A - 72 - 00 - 0460 - 01A - 930A - D Page 7/ 17 Issue 001 - 00 - 2022 - 04 - 01 © CFM

PROPRIET AR Y

INFORMA TION:

Subject to the restrictions on the media.

LEAP - 1A - 72 - 00 - 0460 - 01A - 930A - D 2 If the engine is a Group 2 engine, remove and replace the HPT rotor interstage seal (1, Figure 1 ) (SIN:

157B0).

Removal and installation instructions have not changed.

Refer to the LEAP - 1A ESM, 72 - 52 - 00,

DISASSEMBLE

PROCEDURE ( Refer to:

LEAP - 1A - 72 - 52 - 00 - 01A - 530A - C ) and ASSEM- BLE

PROCEDURE ( Refer to:

LEAP - 1A - 72 - 52 - 00 - 01A - 710A - C ).

3 If the engine is a Group 1 engine or has operated in the two, Group 1 and Group 2 engine models, remove and replace the HPT rotor interstage seal (1, Figure 1 ) (SIN:

157B0) and HPT rotor stage 2 disk

(3) (SIN:

158B0).

Removal and installation instructions have not changed.

Refer to the LEAP - 1A ESM, 72 - 52 - 00,

DISASSEMBLE

PROCEDURE ( Refer to:

LEAP - 1A - 72 - 52 - 00 - 01A - 530A - C ) and AS- SEMBLE

PROCEDURE ( Refer to:

LEAP - 1A - 72 - 52 - 00 - 01A - 710A - C ).

(4) Do an inspection of the honeycomb of the HPT stator stationary seal (1, Figure 5 ) (SIN:

925A3) as specified in below criteria and do as follows:

(a) T ake measurements of four equally spaced locations circumferentially , which include approximately deepest rub location.

Refer to Figure 5 for more information and the criteria that follow:

1 Maximum permitted average depth of all grooves

0.012 inch

(0.30 mm) 2 Maximum permitted individual groove width is

0.170 inch

(4.32 mm) 3 There must be four annular wear grooves separated by a minimum of

1.0 complete cell.

There must be

1.5 complete cells on the forward and aft ends of the honeycomb.

4 Report the results to CFM.

Refer to paragraph

6.,

ADDITIONAL

INFORMA TION for CFM contact information.

(b) If the HPT stator stationary seal (1, Figure 5 ) (SIN:

925A3) honeycomb inspection meets all of the above criteria, no action is necessary for the HPT stator stationary seal

(1) (SIN:

925A3).

(c) If the HPT stator stationary seal

(1) (SIN:

925A3) honeycomb inspection does not meet all of the above criteria, do as follows:

1 Remove and replace the HPT stator stationary seal

(1) (SIN:

925A3).

Removal and installation instructions have not changed.

Refer to the LEAP - 1A ESM, 72 - 54 - 00,

DISASSEMBLE

PROCEDURE ( Refer to:

LEAP - 1A - 72 - 54 - 00 - 01A - 530A - C ) and

ASSEMBLE

PROCEDURE ( Refer to:

LEAP - 1A - 72 - 54 - 00 - 01A - 710A - C ).

LEAP - 1A - 72 - 00 - 0460 - 01A - 930A - D Page 8/ 17 Issue 001 - 00 - 2022 - 04 - 01 © CFM

PROPRIET AR Y

INFORMA TION:

Subject to the restrictions on the media.

LEAP - 1A - 72 - 00 - 0460 - 01A - 930A - D HPT Rotor Assembly Piece - part Inspection Figure 1 (Sheet 1 of

2) LEAP - 1A - 72 - 00 - 0460 - 01A - 930A - D Page 9/ 17 Issue 001 - 00 - 2022 - 04 - 01 © CFM

PROPRIET AR Y

INFORMA TION:

Subject to the restrictions on the media.

LEAP - 1A - 72 - 00 - 0460 - 01A - 930A - D HPT Rotor Assembly Piece - part Inspection Figure 1 (Sheet 2 of

2) LEAP - 1A - 72 - 00 - 0460 - 01A - 930A - D Page 10/ 17 Issue 001 - 00 - 2022 - 04 - 01 © CFM

PROPRIET AR Y

INFORMA TION:

Subject to the restrictions on the media.

LEAP - 1A - 72 - 00 - 0460 - 01A - 930A - D Engine Threshold Removal Calculation Figure 2 LEAP - 1A - 72 - 00 - 0460 - 01A - 930A - D Page 1 1/ 17 Issue 001 - 00 - 2022 - 04 - 01 © CFM

PROPRIET AR Y

INFORMA TION:

Subject to the restrictions on the media.

LEAP - 1A - 72 - 00 - 0460 - 01A - 930A - D Stage 2 HPT Nozzle Assembly Location Figure 3 (Sheet 1 of

2) LEAP - 1A - 72 - 00 - 0460 - 01A - 930A - D Page 12/ 17 Issue 001 - 00 - 2022 - 04 - 01 © CFM

PROPRIET AR Y

INFORMA TION:

Subject to the restrictions on the media.

Pages 13–17 of 17