Copy · CSB15-2C · 6 pages

© Continental Aerospace Technologies, Inc. Filed by the FAA in regulations.gov docket FAA-2016-0069; AD 2016-21-04 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

TextOCR

This text is OCR from a scan. OCR can misread letters and numbers.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '82bff2cba363924cdcaa3b3926ef97cc434d0781bba261e41f8f9e3664f3e917'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Page 1OCROpen in PDF

CONTINENTAL MOTORS® AIRCRAFT ENGINE CATEGORY 2 CRITICAL SERVICE BULLETIN CSB15-2C SUPERSEDES CSB15-2B

COMPLIANCE NECESSARY TO MAINTAIN SAFETY TECHNICAL PORTIONS

FAA APPROVED SUBJECT: Oil Cooler Cross Fitting Replacement PURPOSE: To replace oil cooler cross fitting (part numbers AN918-1J and AN918-2J) with a new enhanced cross fitting (P/N. 658607).

COMPLIANCE: Within the next 25 hours of engine operation or the next scheduled inspection or engine servicing, whichever occurs first.

MODELS AFFECTED: New and rebuilt TSIO550-C5, -C7, -C8, -C9, -C10, -C11, -C12, -C13, -C17, - C18, -C19, -C20, -C21; TSIO550-N; TSIOF550-D; TSIOF550-K aviation • gasoline (AvGas) engine models that use oil cooler cross fitting P/Ns AN918-1J or AN918-2J with engine serial numbers prior to 1012296.

I. GENERAL INFORMATION Continental Motors, Inc. (CMI) is aware of some occurrences where a loss of engine oil resulted from a fractured nipple fitting between the cross fitting and the oil cooler. Design improvements consolidate the oil cooler cross fitting stack-up into a single part, which significantly increases the strength and provides a simplified procedure for installing the oil cooler cross fitting found on specified TSIO-550 and TSIOF-550 engines. Modifications described herein on engine serial numbers 1012296 and higher were accomplished at the factory.

WARNING It is critical to follow ALL "Standard Practices" within your Maintenance and Overhaul Manual when connecting fittings and hoses.

II. BACKGROUND INFORMATION CMI has made several design enhancements to the cross fitting configuration that provides lubricating oil to the turbocharger bearings, and, in some cases, the oil pressure sensor.

Located in your M-18 (29 May 2015) or M-26 (15 September 2014), or later revision, • Maintenance and Overhaul Manuals:

1. Chapter 17 provides detailed instructions on installing the pipe fittings found on the oil cooler and the authorized pipe sealant to be used

2. Appendix B provides the "General Torque Specifications" to be used when tightening the pipe fittings and B-nuts.

CAUTION: It is critical to follow Standard Practices to prevent applying twisting or shear loads, or over torquing the mated fittings.

3. Appendix C provides specific instructions to properly support equipment during installation of fittings and/or B-nuts (reference section C-12, "Hose and Tubing Installation."

ISSUED REVISED PAGE NO DOC NO REVISION 2015/07/02 2015/11/09 1 of 6 CSB15-2 P.O. Box 90 Mobile, AL 251-436-8299 ©2015 Continental Motors, Inc.

Page 2OCROpen in PDF

Design enhancements:

1. Eliminate the pipe bushing and nipple fitting stack-up (see Figure 1) typically found between the cross fitting and the oil cooler and replaces them with a single cross fitting (P/N 658607).

2. Provide a larger tool surface area on the cross fitting for support wrenches during subsequent fitting and b-nut installation.

3. Added AN915-1J, 45-degree elbow fitting, to specific TSIO550-C engine models to accommodate optional oil pressure sensor installation (similar orientation as TSIOF550-D, sce Figure 2).

4. Remove the additional pipe bushings (P/N AS4861J01) used for the oil pressure sensor and pipe plug previously installed on TSIO550-C20B and -C21B installations (see Figure 1). These bushings are obsolete (for this application) and will no longer be necessary for the new cross fitting installation; the AN915-1J 45-degree elbow fitting or pipe plugs fit directly into the new cross fitting (see Figure 2).

Bushing, typ.

Pipe = Bushings Pipe - Bushings Nipple, typ.- Cross, typ.

TSIO550-C, AS ENUMERATED TSIO550-C20B TSIO550-C21B Bushing, typ.

Nipple, typ.

Cross, typ.

TSIO550-N TSIOF550-D TSIOF550-K Figure 1. Cross Fitting Stack-Up, Prior Configurations

ISSUED REVISED PAGE NO DOC NO REVISION 2015/07/02 2015/11/09 2 of 6 CSB15-2 P.O. Box 90 Mobile, AL 251-436-8299

Page 3OCROpen in PDF

Elbow- Elbow- - Plug Plug Sensor, Sensor, Oil Press. Oil Press / Cross Fitting Cross - Plug Fitting Cross - Plug Fitting Flared Flared

- Elbow Nipple Nipple TSIO550-C & N TSIOF550-D TSIOF550-K Figure 2. Cross Fitting, NEW Configurations III. ACTION REQUIRED REMOVE AND REPLACE the superseded parts with new cross fitting (P/N 658607) using the same procedures located in your M-18 or M-26 Maintenance and Overhaul Manuals. Reference the latest revision of the CMI Illustrated Parts Catalog (IPC) to determine applicable additional connectors, elbows, or plug part numbers and adjust the instructions accordingly.

OLD FITTING NEW FITTING AN918-1J, AN918-2J 658607 Figure 3. Cross Fitting, Comparison

WARNING Use eye protection when cutting safety wire to prevent eye injury.

1. Remove and discard safety wire securing vernatherm to oil cooler pipe bushing.

2. Follow the detailed instructions for removing and installing pipe fittings found on oil coolers (Chapter 17-6) using sealant specified.

3. Use a minimum 10X magnifying lens to visually inspect outboard port threads at the aft side of the oil cooler for contamination, distortion, or damage before installing new cross fitting (P/N 658607).

a. If determined serviceable, continue installing new cross fitting.

b. If there is evidence of contamination or damage, please contact Continental Motors Customer Service Department directly at 1(800) 326-0089.

ISSUED REVISED PAGE NO DOC NO REVISION 2015/07/02 2015/11/09 3 of 6 CSB15-2 C P.O. Box 90 Mobile, AL 251-436-8299

Page 4OCROpen in PDF

4. Reference Appendix B, "General Torque Specifications" for torque pipe fitting installation instructions (NPTF threads):

a. Screw the cross fitting (P/N 658607) into the outboard port (at the aft side of the oil cooler) to the finger tight position.

b. Wrench tighten the cross fitting to the appropriate clocking of fitting within 1-3 turns from the finger tight position. Minimum torque of 185 in/Ibs must be achieved upon clocking position of fitting.

NOTE: The fitting is not to be loosened in order to achieve proper alignment (clocking). Torque values specified are for reference only. Torque values must be used on other pipe fittings or plugs where clocking is not required.

5. Reference Appendix C, "Hose and Tubing Installation' when installing fittings and/or B-nuts.

CAUTION: It is critical to support pipe fittings and follow Standard Practices to prevent applying twisting or shear loads, ar over torquing the mated fittings.

a. Use a wrench on both mating connections to avoid applying excessive torque to the fittings. Securely tighten fittings and torque to the specified value in Appendix B.

Torque the hose or tubing end fitting while maintaining sufficient force on adjacent fittings to prevent twisting and shear loads.

CAUTION: Do not exceed specified torque values.

b. Support the last fitting in the assembly on components that contain multiple fittings coupled in one location (see Figure 4). DO NOT over-torque fittings.

Fitting to be "Clocked" Support Fitting with Cross Fitting Open End Wrench Figure 4. Hose and Tube Installation Support

6. Install new safety wire securing vernatherm to cross fitting. Reference Appendix C-4, "Safety Wire Hardware" to properly secure hardware.

ISSUED REVISED PAGE NO DOC NO REVISION 2015/07/02 2015/11/09 4 of 6 CSB15-2 P.O. Box 90 Mobile, AL 251-436-8299

Page 5OCROpen in PDF

7. Conduct a normal engine start and ground run-up according to your Airplane Flight Manual / Pilot's Operating Handbook (AFM/POH) provided by the airframe manufacturer.

8. Perform a visual leak check of the serviced area, after shut-down, prior to placing aircraft in service.

9. Make appropriate logbook entries detailing compliance actions taken in accordance with this Critical Service Bulletin (CSB15-2). The logbook entry must include a complete listing of parts used in this installation.

10. Return aircraft to service.

IV. WARRANTY This Critical Service Bulletin is your authorization to perform the required inspection, replace the affected parts), and receive warranty reimbursement, limited to the "Models Affected" and compliance action required as defined within. Contact your authorized Continental Motors distributor for warranty claim application and parts return instructions.

Contact Continental Motors Technical Services at one of the numbers listed below if you have any questions concerning the technical content of this Critical Service Bulletin.

1.888.826.5465 toll free in United States +1.251.436.8299 international callers +1.305.964.0872 en Español NOTE: Visit the Continental Motors web site at www.contincntalmotors.acro to obtain copies of Continental Motors Warranty Policies.

A. Allowances/Reimbursements Table 1. Labor allowance shall be:

Labor Allowance Scope of Work (hr) Remove and replace superseded parts. 1.0 B. Illustrated Parts Catalog Instructions Replacement parts required to comply with this bulletin are published in the illustrated parts catalogs on the Continental Motors web site and may be ordered through any authorized Continental Motors distributor.

NOTE: To find an authorized Continental Motors distributor, follow this link: http://www.continentalmotors.aero/ Support Materials/Authorized_Distributor_Listing!

ISSUED REVISED PAGE NO DOC NO REVISION 2015/07/02 2015/11/09 5 of 6 CSB15-2 P.O. Box 90 Mobile, AL 251-436-8299

Page 6OCROpen in PDF

Intentionally Left Blank

ISSUED REVISED ON TO 2015/07/02 2015/11/09 9 10 9 P.O. Box 90 Mobile, AL 251-436-8299