Copy · Daher Aerospace Service Bulletin 70-254 · 10 pages

© Socata. Filed by the FAA in regulations.gov docket FAA-2020-1069; AD 2021-25-10 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

TextPartly OCR

Some pages are OCR from a scan. OCR can misread letters and numbers.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '71c28b09b878938ef8e392889c5e412f731fdb945c3c5332644aca39e1406ede'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Page 1 / 10APR 18 Rev. 3 --- DEC 17 SUBJECT : O I LCOOLER AIR INDUCTION DUCT REFERENCE : MOD70---0616---79 EFFECTIVITY : TBM S/N 1 to 684 which have applied SB70---231---79, Originalissue.

TBMS/N687to1038whichhaveappliedSB70---219---24,Originalissueand/orRevision1.

TBM S/N 1039 to 1230 NOTE :

For the other aircraft, the modification MOD70- - -0616- - -79 is applied at the factory.

PURPOSE :

A. PROBLEM Possible increase of oil temperature which may lead to an engine shutdown while maneuvering margin is reduced due to ice accumulation.

B. ROOT CAUSE Lossofefficiencyofoilcooler systemcaused byice accumulationon airinlet ductfins.

C. SOLUTION Removalof the four upper fins of the oilcooler air induction duct.

SUMMARY :

A. PRELIMINARY STEPS B. OILCOOLER AIR INDUCTIONDUCT MODIFICATION C. FINALSTEPS APPLICATION: During the next scheduled inspection and at the latest on October 1st, 2018.

WARRANTY : Parts will be covered under warranty regardless of the warranty status of the aircraft. This campaign willend 1 year and 1 month after the SB issue reference date.

PROCURABLE MATERIAL:

Parts to be ordered from your TBM spare parts distributor :

--- EpoxyresinandhardenerRef.EPOLAM2017orresinEL---360andhardenerEL---360---1, or equivalent.

SERVICE BULLETIN

TBM AIRCRAFT

MANDATORY The technicalcontent of this document is approved un der the authority of DOA No. EASA.21J.013 isthe subject ofan AD SB 70--254 REVISION 3 79 ATA No.

DAHER AEROSPACE Di rection des Services TELEPHONE: 33(0)562.41.73.00 65921TARBESCEDEX9 TELEFAX: 33(0)562.41.76.54 FRANCE

SERVICE BULLETIN

TBM AIRCRAFT

MANDATORY The technicalcontent of this document is approved un der the authority of DOA No. EASA.21J.013 is the subject of an AD SB 70--254 REVISION 3 79 ATA No.

Page 2 / 10AP R 18 Rev. 3 --- DEC 17 CONSUMABLE MATERIAL or OTHER PRODUCTS(Lo calpurchase) :

--- Methyl---Ethyl---Ketone (M.E.K.)

TOOLS :

--- Standard aeronauticalmaintenance station tools RELATED DOCUMENTS:

--- Maintenance Manual, Chapters 06---30---01 page 001 and 71---10---00 page 401.

MANPOWER :

--- 1 aeronauticalmechanic :3 hours TECHNICAL INCIDENCES:

--- None DESCRIPTION OF ACCOMPLISHMENT INSTRUCTIONS:

NOTE :

Operations required in this Service Bulletin must be accomplished by persons authorized by their Airworthiness Authorities and according to the procedure described hereafter.

A. PRELIMINARY STEPS

1) Make sure the ”SOURCE” selector is set to ”OFF” and the crash lever is down.

2) Install the warning sign prohibiting ”SOURCE” selector operation

WARNING

DO NOT OPERATE MA

INTENANCE WORK IN PROGRESS

3) Remove front lower cowling 122 --- refer to Chapters 06---30---01 page 001 and 71 ---10---00 page 401 of the MaintenanceManual.

4) Remove rear L.H. cowling 133 --- refer to Chapters 06---30---01 page 001 and 71---10---00 page 401 of the MaintenanceManual.

5) Remove and retain clamps (3) and (5);disconnect hoses (2) and (4).

6) Remove and retain bolts (7) and washers (6).

7) Remove and retain bolts (9) and washers (8).

8) Hold oilcooler (11), then remove and retain oilcooler air induction duct (1).

9) Temporarily install oil cooler (11) on bracket (12) and strut (13) with bolts (7) and washers (6).

SERVICE BULLETIN

TBM AIRCRAFT

MANDATORY The technicalcontent of this document is approved un der the authority of DOA No. EASA.21J.013 is the subject of an AD SB 70--254 REVISION 3 79 ATA No.

Page 3 / 10AP R 18 Rev. 3 --- DEC 17 B. OILCOOLER AIR INDUCTIONDUCT MODIFICATION --- see Figure 1

WARNING WEAR MASK, PROTECTION GLOVES AND GOGGLES.

NOTE :

To guide you through this process, some photographies are available at the end of this Service Bulletin.

1) Usingcuttingpliers,cutanddiscardthefourupperfinsoftheoilcoolerairinduction duct (1) --- see Figure 1 .

2) With a belt sander, fully remove the four upper fins and sand the surfaces that will be protected by resin at step 5).

3) Vacuum chips and clean area with a clean cloth moistened with M.E.K.

4) Degrease untilremovalof anytrace of dirt or grease from both surfaces.

Oil cooler air induction duct Ref. T700H792001900400, T700H792001900600, T700H792000900000 orT700A7920040001

CAUTION REFER TO RESIN AND HADENER NOTICE FOR PREPARATION AND USE.

5) Protect bare surface with epoxy resin and hardener Ref. EPOLAM 2017 or resin EL---360 and hardener EL---360---1 or equivalent.

All

6) Aftermodificationoftheoilcoolerairinductionduct(1),itmustbere---identifiedwith a permanent marker, as indicated hereafter :

Pre---SB Reference Post---SB Reference T700H792001900600 T700H512008100000 T700H792001900400 T700H512008100100 T700A7920040001 T700H512008100200 T700H792001900200 T700H512008100300 T700H792001900000 T700H512008100400 T700H792000900000 T700H512008100500 C. FINALSTEPS

1) Remove oil cooler (11) from bracket (12) and strut (13) temporarily installed at step A.9).

2) Installoilcooler modified air induction duct (1) on oilcooler (11).

3) Installwashers (6) and bolts (7). Screw but do not fully tighten.

4) Installwashers (8) and bolts (9). Screw but do not fully tighten.

5) Connect hoses (2) and (4) on oil cooler modified air induction duct (1) with clamps (3) and (5).

SERVICE BULLETIN

TBM AIRCRAFT

MANDATORY The technicalcontent of this document is approved un der the authority of DOA No. EASA.21J.013 is the subject of an AD SB 70--254 REVISION 3 79 ATA No.

Page 4 / 10AP R 18 Rev. 3 --- DEC 17

6) Tightentheassembly.Makesurethatoilcoolerairinducti on duct(1)isnotstressed.

7) Make sure all the tools and materials are removed and the work area is clean and free from debris.

8) Install front lower cowling 122 --- refer to Chapters 06---30---01 page 001 and 71---10---00 page 401 of the MaintenanceManual.

9) InstallrearL.H.cowling133---refertoChapters06---30---01page001and71---10---00 page 401 of the Maintenance Manual.

10) Remove the warning sign prohibiting ”SOURCE” selector operation.

UPDATING OF THE AIRCRAFT DOCUMENTATION:

Upon completion of Service Bulletin No. SB 70---254---79 ”OIL COOLER AIR INDUCTION DUCT”, (Reference MOD70---0616---79), make an appropriate maintenance record entry.

WARNING : DAHER AEROSPACE considers that it is MANDATORY for operators to comply with the instructions of this SB.

OperatorswhoarbitrarilyignorethecompliancestatementindicatedinthisSBdosoattheir own risk.

SERVICE BULLETIN

TBM AIRCRAFT

MANDATORY The technicalcontent of this document is approved un der the authority of DOA No. EASA.21J.013 is the subject of an AD SB 70--254 REVISION 3 79 ATA No.

Page 5 / 10AP R 18 Rev. 3 --- DEC 17 Key to Figure 1 --- Oilcooler air induction duct modification 1 --

- Oilcooler air induction duct 2 --- Hose 3 --- Clamp 4 --- Hose 5 --- Clamp 6 --- Washer 7 --- Bolt 8 --- Washer 9 --- Bolt 10 --- Spacer 11 --- Oilcooler 12 --- Bracket 13 --- Strut

Page 6OCROpen in PDF

TBM AIRCRAFT SERVICE BULLETIN SB 70-254 79 ATA No

MANDATORY The technical content of this document is approved under the authority of DOA No. EASA.21J.013 is the subject of an AD PRE SB70-254-79 POST SB70-254-79 I4792000AAAZMA4600 11 Figure 1 - Oil cooler air induction duct modification APR 18 Page 6 / 10

SERVICE BULLETIN

TBM AIRCRAFT

MANDATORY The technicalcontent of this document is approved un der the authority of DOA No. EASA.21J.013 is the subject of an AD SB 70--254 REVISION 3 79 ATA No.

Page 7 / 10AP R 18 Rev. 3 --- DEC 17 TOOLS

CUTTING

SERVICE BULLETIN

TBM AIRCRAFT

MANDATORY The technicalcontent of this document is approved un der the authority of DOA No. EASA.21J.013 is the subject of an AD SB 70--254 REVISION 3 79 ATA No.

Page 8 / 10AP R 18 Rev. 3 --- DEC 17

FINISH CUTTING SAN DING

SERVICE BULLETIN

TBM AIRCRAFT

MANDATORY The technicalcontent of this document is approved un der the authority of DOA No. EASA.21J.013 is the subject of an AD SB 70--254 REVISION 3 79 ATA No.

Page 9 / 10AP R 18 Rev. 3 --- DEC 17

POST---SANDING

SERVICE BULLETIN

TBM AIRCRAFT

MANDATORY The technicalcontent of this document is approved un der the authority of DOA No. EASA.21J.013 is the subject of an AD SB 70--254 REVISION 3 79 ATA No.

Page 10 / 10AP R 18 Rev. 3 --- DEC 17

PROTECTION