TextPartly OCR
Some pages are OCR from a scan. OCR can misread letters and numbers.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '5f91658c0546843a5c4eba3f76a10b16ee0815f8ed7da9db881126d9040af516' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '5f91658c0546843a5c4eba3f76a10b16ee0815f8ed7da9db881126d9040af516' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
FALCON 7X No 602 JUNE 03, 2024
A TA 00
GENERAL
ENHANCED AVIONICS SYSTEM
EASY IV - LGIO AIRCRAFT
FALCON SERVICE BULLETIN Copyright © 2024 by Dassault Aviation All rights reserved. No part of this work may be reproduced or copied in any form or by any means without written permission of Dassault A viation.
GENERAL
ENHANCED A
VIONICS SYSTEM
EASY IV - LGIO AIRCRAFT Initial issuance March 05, 2024 List of effective pages:
1 to 42 Erratum June 03, 2024 List of effective pages:
1 to 42 REASON: Additional information.
FALCON 7X 7X -602 ATA 00
GENERAL
ENHANCED A
VIONICS SYSTEM
EASY IV - LGIO AIRCRAFT
1. PLANNING INFORMATION A. EFFECTIVITY This Service Bulletin is applicable to FALCON 7X aircraft with serial numbers 2 thru 261 that have not previously implemented DASSAULT AVIATION FALCON modification M2059.
B. REASON The purpose of this Service Bulletin is to upgrade the aircraft avionics to the EASy IV load 18.0 standard that includes the following features:
• an advanced version of the INAV moving map with interactive Vertical Situation Display, combined with new Vivid Displays,
• a combination of the most advanced versions of Honeywell’s NextGen FMS and Communication Management Function,
• a dual charts function on aircraft already equipped with single charts, which introduces redundancy for the use of the electronic Jeppesen charts,
• improved Jeppesen charts function with a new Night mode, a Panoramic mode, as well as the display of the aircraft symbol on all georeferenced terminal charts (dual charts required),
• Runway Overrun Awarness and Alerting System (ROAAS) which analyzes the aircraft trajectory and the TOLD landing performance to determine if the aircraft can safely come to a full stop within the remaining runway length,
• enhanced ADS-B IN Cockpit Display of Traffic Information (CDTI) with 2 applications:
• Visual Separation on Approach (VSA): displays specific traffic information relative to select traffic, to facilitate visual separation,
• AIRB: displays ADS-B airborne traffic on the INAV moving map,
• enhanced TOLD function,
• "push-to-load" function,
• weak point fix in the Falcon 7X EASy avionics architecture (equivalent to DASSAULT AVIATION Service Bulletin 7X-591 "EASY II 5TH CERT - LEGACY I/O"). This weak point can lead to the display of misleading data on the display units.
C. DESCRIPTION The operation consists in:
• modifying the aircraft wiring,
• installing wiring provision in anticipation of a future radar installation,
• modifying the hardware configuration:
• replacement of modules in MAU 1 and 2,
• replacement of NIM modules,
• replacement of ASCB bus coupler modules,
• replacement of TCAS transceiver and antennas,
• replacement of DMU by DLMU, FALCON 7X 7X -602 June 03, 2024 ATA 00 Initial issuance Page 1 / 42 DASSAULT AVIATION Proprietary Data
• performing a full software load.
D.
COMPLIANCE If you choose to comply with this Service Bulletin, accomplishment can be performed at your convenience.
E. APPROVAL This Service Bulletin covers DASSAULT AVIATION modifications:
• M-OPT22, M-OPT640, M-OPT1142, M-OPT1144, M1254, M1314, M1341 and M2059 that have been approved by EASA.
• M1363, M2034, M2060, M2104 and M2128 that have been approved under the authority of the DOA ref. EASA.21J.051.
The technical content of this document is approved under the authority of DOA ref. EASA.21J.051.
NOTE: For aircraft not under EASA and FAA regulations, please refer to the Falcon Service Advisory that lists the countries for which EASy IV is approved.
F. LABOR Estimated labor-hours: Refer to Service Bulletin Commercial Summary .
NOTE: These labor-hours only concern the work described in this Service Bulletin and do not include other maintenance work that may be performed on this occasion.
G. MATERIAL - PRICE AND AVAILABILITY The modification kit may be obtained from either address listed below:
Western hemisphere: DASSAULT FALCON JET CORP.
SP
ARES DISTRIBUTION CENTER 200 RISER ROAD LITTLE FERRY, NJ 07643 U.S.A.
Telephone:
• U.S.A. and CANADA: 1-800-800-4036
• MEXICO: 001-800-800-4036
• Other countries: 1-201-541-4809 Email to: Customer.Care@DassaultFalconJet.com Other continents: DASSAULT AVIATION Falcon Spares 54, A
VENUE MARCEL DASSAULT B.P. 24 33701 MERIGNAC Cedex (FRANCE) Telephone: 33 (0)5.56.18.44.44 Email to: dafsorders@dassault-aviation.com Price and availability on request.
FALCON 7X 7X -602 June 03, 2024 ATA 00 Initial issuance Page 2 / 42 DASSAULT AVIATION Proprietary Data
H. TOOLING - PRICE AND AVAILABILITY T OOL BOX (TO-20-008) I.
WEIGHT AND BALANCE Change in weight: None.
Change in balance with respect to 25% MAC: None.
J. REFERENCES Structural Repair Manual:
• DRILLING (Refer to RPI 51-40-03)
• RIVETING (Refer to RPI 51-40-04)
• COUNTERSINKING (Refer to RPI 51-40-06) Aircraft Maintenance Manual:
• GENERAL MAINTENANCE AND SAFETY PRECAUTIONS (Refer to TASK 20-00-00-910-801)
• USE OF THE AIRCRAFT MAINTENANCE PROCEDURES (Refer to TASK 20-00-00-910-803)
• BASIC SEALING METHODS (Refer to TASK 20-32-00-390-801)
• REPLACEMENT OF LOCKWIRES AND SNAPWIRES (Refer to TASK 20-42-01-960-801)
• PROTECTION SCHEME (Refer to SDS 20-60-00)
• APPLICATION OF ALODINE (Refer to TASK 20-60-00-370-801)
• APPLICA TION OF TYPE 5014 AND 5015 POLYURETHANE PRIMERS (Refer to TASK 20-60-00-370-809)
• UNPLUGGING / PLUGGING OF THE MAU BACKSHELLS (Refer to TASK 20-92-00-910-801)
• INSER TION AND EXTRACTION OF A WIRE FITTED WITH A LOCK-IN CONTACT (Refer to TASK 20-95-00-910-801)
• ENERGIZA TION / DE-ENERGIZATION OF THE AIRCRAFT SYSTEMS (Refer to TASK 24-00-00-860-801)
• REMOV AL / INSTALLATION OF THE ELT CONTROL PANEL (Refer to TASK 25-61-17-900-801)
• REMOVAL / INSTALLATION OF THE MAU CHASSIS (Refer to TASK 31-41-01-900-801)
• REMOV AL / INSTALLATION OF THE POWER SUPPLY MODULES (Refer to TASK 31-41-05-900-801)
• REMOV AL / INSTALLATION OF THE PROCESSOR MODULES (Refer to TASK 31-41-09-900-802)
• OPERA TIONAL TEST OF THE DATA ACQUISITION SYSTEM - MAU (Refer to TASK 31-42-00-710-801)
• REMOV AL / INSTALLATION OF THE NIC / PROCESSOR MODULES (Refer to TASK 31-42-01-900-801)
• REMOV AL / INSTALLATION OF THE CONTROL I/O 2 MODULE (Refer to TASK 31-42-05-900-801)
• REMOV AL / INSTALLATION OF THE CONTROL/VIDEO I/O 1 MODULE (Refer to TASK 31-42-09-900-801)
• REMOV AL / INSTALLATION OF THE GENERIC I/O MODULES (Refer to TASK 31-42-13-900-801)
• REMOV AL / INSTALLATION OF THE ASCB BUS COUPLERS (Refer to TASK 31-42-17-900-801) FALCON 7X 7X -602 June 03, 2024 ATA 00 Initial issuance Page 3 / 42 DASSAULT AVIATION Proprietary Data
• REMOV AL / INSTALLATION OF THE NETWORK INTERFACE MODULES (NIM) (Refer to TASK 31-43-05-900-801)
• OPERA TIONAL TEST OF THE CENTRAL DISPLAY SYSTEM (CDS) (Refer to TASK 31-60-00-710-801)
• REMOV AL / INSTALLATION OF THE ADVANCED GRAPHICS MODULES (AGM) (Refer to TASK 31-60-17-900-801)
• REMOV
AL / INSTALLATION OF THE AIR DATA, ATTITUDE AND HEADING REFERENCE SYSTEM (ADAHRS) UNIT (Refer to TASK 34-22-01-900-801)
• OPERA TIONAL TEST OF THE TRAFFIC / COLLISION AVOIDANCE SYSTEM (TCAS) (Refer to TASK 34-44-00-710-801)
• REMOVAL / INSTALLATION OF THE TCAS TRANSCEIVER (Refer to TASK 34-44-01-900-801)
• REMOVAL / INSTALLATION OF THE TCAS ANTENNAS (Refer to TASK 34-44-05-900-801)
• OPERA
TIONAL TEST OF THE ENHANCED GROUND PROXIMITY WARNING SYSTEM (EGPWS) (Refer to TASK 34-45-00-710-801)
• OPERA TIONAL TEST OF THE CENTRAL MAINTENANCE COMPUTER (CMC) (Refer to TASK 45-10-00-710-801)
• INSTALLATION OF AVIONICS SOFTWARE TOOLS (Refer to TASK 45-10-00-860-801)
• REMOV AL / INSTALLATION OF THE FLIGHT DECK PRINTER (Refer to TASK 45-10-09-900-801)
• PERIODIC DATABASE LOADING (Refer to TASK 45-90-00-860-801)
• DATABASE LOADING (Refer to TASK 45-90-00-860-803)
• SOFTWARE LOADING (Refer to TASK 45-90-00-860-804)
• REMOV AL / INSTALLATION OF THE DATA MANAGEMENT UNIT (DMU) (Refer to TASK 45-90-01-900-801)
• REMOV AL / INSTALLATION OF THE DATA LAN MANAGEMENT UNIT (DLMU) (Refer to TASK 45-90-01-900-802)
• USE OF THE APM SETTINGS TOOL (Refer to TASK 45-91-00-910-801)
• REMOV AL / INSTALLATION OF THE CABIN FLOOR PANELS (Refer to TASK 53-04-01-900-801)
• REMOV AL / INSTALLATION OF THE OPTIONAL EQUIPMENT FLOOR PANEL (Refer to TASK 53-04-07-900-801)
• OPENING / CLOSING OF THE NOSE CONE (Refer to TASK 53-10-09-860-801)
• REMOVAL / INSTALLATION OF THE T34 BODY FAIRINGS (Refer to TASK 53-60-00-900-801) Wiring Diagram Manual:
• Refer to WD 23-10-00
• Refer to WD 23-10-20
• Refer to WD 34-23-50
• Refer to WD 34-40-00
• Refer to WD 34-45-00
• Refer to WD 45-90-00
DASSAUL T AVIATION Service Bulletins/Modifications:
• M111 "BIRD STRIKE INTO FRAME 1"
• 7X-603 "LOADING THE LATEST AMI DATABASE AND SWITCHING AMI DATABASE PROVIDER" FALCON 7X 7X -602 June 03, 2024 ATA 00 Initial issuance Page 4 / 42 DASSAULT AVIATION Proprietary Data
K. OTHER PUBLICATIONS AFFECTED The following publication is revised to account for the changes introduced by this Service Bulletin:
• Airplane Flight Manual revision 25 or subsequent revision The following publications will be revised at a later date to account for the changes introduced by this Service Bulletin:
• CODDE 1 revision 14
• CODDE 2 revision 25
• QRH 1 revision 25
• QRH 2 revision 25
• Illustrated Parts Catalog
• Aircraft Maintenance Manual
• Fault Isolation Manual
• Wiring Diagram Manual Operational Suitability Data:
• Operational Suitability Data - Flight Crew:
• OSM-FC revision 8 or subsequent revision
• Operational Suitability Manual - Master Minimum Equipment List:
• OSM-MMEL revision 16 or subsequent revision FALCON 7X 7X -602 June 03, 2024 ATA 00 Initial issuance Page 5 / 42 DASSAULT AVIATION Proprietary Data
2. ACCOMPLISHMENT INSTRUCTIONS Refer to fig. 1 for general view of the work area.
A.
GENERAL INSTRUCTIONS AND SAFETY PRECAUTIONS
(1) Obey the general maintenance and safety precautions (Refer to TASK 20-00-00-910-801).
(2) Obey the general electrical instructions:
(a) When mechanical retrofit and/or modification operations are performed on the aircraft, take special care to protect the wiring in order to prevent metal chips (or burrs) from penetrating the wire bundles, since these could eventually damage the insulation sheathing of the wires.
Whenever possible, it is recommended that the wiring be removed from the work area. If that is not possible, it is absolutely necessary to protect the wiring.
(b) Due to the risk of damaging the wire insulation, it is prohibited to blindly drill holes through a box structure containing wiring.
(c) New wires that are installed alongside existing wires should be secured with the existing clamp.
(d) Check that all connections are properly protected to ensure proper insulation, and that markings are visible and appropriate.
(e) Connector wires should be inserted and extracted as per the recommendations in Standard Practices (Refer to TASK 20-95-00-910-801).
(f) Electrical and electronic equipment should be removed and installed as per the recommendations in Standard Practices (Refer to TASK 20-00-00-910-801).
(g) V isually inspect the work area for particles or debris, then vacuum-clean the area. Blowing compressed air is prohibited since it could move metal chips into inaccessible areas.
(3) Obey the Structural Repair Manual and Standard Practices procedures for the following operations:
• drilling (Refer to RPI 51-40-03),
• riveting (Refer to RPI 51-40-04),
• countersinking (Refer to RPI 51-40-06),
• basic sealing methods (Refer to TASK 20-32-00-390-801).
B.
PRELIMINARY STEPS
(1) The aircraft must be in the maintenance configuration (Refer to TASK 20-00-00-910-803).
(2) On the “System Config” page, note the APM Settings configuration on the table (Refer to TASK 45-91-00-910-801).
(3) De-energize the aircraft systems (Refer to TASK 24-00-00-860-801).
(4) Open the nose cone (210) (Refer to TASK 53-10-09-860-801).
(5) Remove the necessary equipment and interior accommodation items to get access to cockpit and cabin floors (113JZ), (114AZ), (114BZ), (114CZ), (114DZ), (114FZ), (114GZ), (121BZ), (121CZ), (121DZ), ( 121EZ), ( 121FZ), ( 121GZ), (122AZ), (122BZ), ( 122CZ), ( 131BZ) and (131CZ).
(6) Remove the cabin floors listed above (Refer to TASK 53-04-01-900-801).
FALCON 7X 7X -602 June 03, 2024 ATA 00 Initial issuance Page 6 / 42 DASSAULT AVIATION Proprietary Data
(7) Remove the optional equipment floor panel (Refer to TASK 53-04-07-900-801).
(8) Remove the ADAHRS UNIT (Refer to TASK 34-22-01-900-801).
(9) Remove the TCAS transceiver (103NP) (Refer to TASK 34-44-01-900-801).
(10) Remove the DMU (901FP) (Refer to TASK 45-90-01-900-801).
(1
1) Remove the ELT control panel (701FP) (Refer to TASK 25-61-17-900-801).
(12) If installed, remove the printer (104MP) (Refer to TASK 45-10-09-900-801).
(13) Remove the MAU 1 chassis (Refer to TASK 31-41-01-900-801).
(14) Remove the following backshells from the MAU 2 (Refer to TASK 20-92-00-910-801):
• AGM modules (2301FD) and (2401FD)
• NIC/processor modules (2301FY) and (2401FY)
• CMC module (2505TC)
(15) Remove the backshells from the NIM modules ( 1101NZ) and ( 1201NZ) (Refer to TASK 31-43-05-900-801).
C.
STRUCTURAL MODIFICATIONS
(1) Prepare FR1 RH side for the installation of the new cut-off connector 87J/P as follows:
(a) A/C without M111 (SN<102): remove the front plate (a-fig. 10) from FR1.
(b) Create a cut-out on FR1 as per fig. 10.
NOTE: Depending on aircraft configuration, you can create the cut-out either according to solution 1 or solution 2. Solution 1 is preferable.
(c) Protect the cut-out area (Refer to SDS 20-60-00).
(2) Prepare the FR8/FR9 under floor area for the installation of new cut-off connectors 195J/P and 196J/P as follows:
(a) Remove the old supports (a-fig. 11) and (a-fig. 12).
(b) Plug the four old rivet positions (b-fig. 11) with new rivets (3-fig. 11).
(c) Install the connector bracket (1-fig. 11) on the omega (2-fig. 11) using rivets (4-fig. 11).
(d) Install the assembly (1-fig. 11) and (2-fig. 11) on the frame using rivets (5-fig. 11).
(e) Install the new bundle bracket (1-fig. 12 ) on RH lower FR8/FR9 web (b-fig. 12) in place of the old bracket (a-fig. 12) using rivets (2-fig. 12).
(f) Install the cable holder (4-fig. 12) on the bundle bracket (3-fig. 12) using rivet (5-fig. 12).
(g) Install the assembly (3-fig. 12) and (4-fig. 12) on the structure (c-fig. 12) using rivets (6-fig.
12).
(h) Install the cable holder (1-fig. 13) using rivet (2-fig. 13).
(3) Prepare the RH copilot sideledge area for the installation of the LAN terminal load R5821FY as follows:
(a) Position the LAN terminal load bracket (1-fig. 14) in accordance with the dimensions shown on figure fig. 14.
(b) Drill two holes for rivets (2-fig. 14), then install the bracket.
FALCON 7X 7X -602 June 03, 2024 ATA 00 Initial issuance Page 7 / 42 DASSAULT AVIATION Proprietary Data
D. ELECTRICAL MODIFICATIONS
(1) Perform the following modification on each AGM backshell 1:
(a) Fill the new connector (2-fig. 2) with blanking pins.
NOTE: This new connector has no wire connected to it.
(b) Open backshell 1.
(c) Remove the blank backplate (a-fig. 2).
(d) Install the connector backplate (1-fig. 2 ) and the connector (2-fig. 2).
(e) Close backshell 1.
(2) Perform the following modification on each AGM backshell 2:
(a) Open backshell 2.
(b) Disconnect the two wires of the terrain server bus from the backshell (item 1-fig. 3).
(c) Cap and stow the two wires inside the backshell.
(d) Close backshell 2.
(3) Perform the following modification on the backshell of the EGPWS 1 module ( 101FW):
(a) Open the backshell.
(b) Disconnect the two wires of the terrain server bus from the backshell (item 2-fig. 3).
(c) Cap and stow the two wires with the wiring bundle under the cabin floor.
(d) Discard the backshell.
(4) Perform the electrical modification of the LAN bus as per wiring diagrams fig. 3 and fig. 14.
NOTE 1: Disconnected LAN bus cables must be capped and stowed outside the backshells (item 3-fig. 3).
NOTE 2: New triaxial cables must have a minimum length of 500 mm.
NOTE 3: New triaxial cables must be secured with spacers (3-fig. 14) and (4-fig. 14).
(5) Perform the electrical modification as per wiring diagrams fig. 4 and fig. 15.
NOTE 1: This wiring diagram includes wiring provision in anticipation of a future radar installation.
NOTE 2: Quadrax cable technology does not allow elements to be crossed. Before the installation of quadrax contacts, identify the ends of the cables after cut, and route the cable according to the direction of rotation of the colors, in order not to cross the elements in the rear insulator of the quadrax contacts.
(a) If necessary, remove the duct F7XC213220100A1 to easily route the harness.
(b) Connector 1101NZ1: if there is no space available for the new quadrax cable in the hexashield store, do the following steps:
1 Remove the two hexashields P/N 01C0AFHE3-7 (hexashields without bonding braid).
2 Install all the cables previously associated to these two hexashields in a same hexashield P/N 01C0AFHE3-7 (local procurement).
FALCON 7X 7X -602 June 03, 2024 ATA 00 Initial issuance Page 8 / 42 DASSAULT AVIATION Proprietary Data
3 Install the new quadrax cable in the space now available in the hexashield store.
(6) Perform the following modification on the DLMU connectors:
(a) Replace the Hexashield hood of the aircraft electrical connector 1001FP1 with the new reference (02C0A501CAP3-658).
(b) Secure the protective cap 01C0A501BE6-8D002 by attaching the rope with a cable grip to the backshell of the electrical connector 1001FP2.
(7) Perform the electrical modification as per wiring diagrams fig. 5 and fig. 6.
(8) Perform an electrical continuity check of the aircraft wiring.
E. HARDWARE / EQUIPMENT MODIFICATIONS
(1) A/C without M111 (SN<102):
(a) Modify the front plate (a-fig. 10) to fit with the new cut-off connector 87J/P.
(b) Protect the modified area (Refer to SDS 20-60-00).
(c) Reinstall the modifed plate on FR1.
(d) Apply covering sealant on the heads of the screws (Refer to TASK 20-32-00-390-801).
(2) Install the new TCAS transceiver (103NP) (Refer to TASK 34-44-01-900-801).
(3) Install the DLMU (1001FP) with its SD card (Refer to TASK 45-90-01-900-802).
(4) Re-install the MAU 1 chassis (Refer to TASK 31-41-01-900-801), and do the following steps:
(a) Install the processor P/N 7034056-1901 in slot 14 (initially in slot 16) (1-fig. 7) (Refer to TASK 31-41-09-900-802).
(b) Install the new processor P/N 7034056-1902 in slot 16 (2-fig. 7) (Refer to TASK 31-41-09-900-802).
(c) Install the new NIC/processor modules ( 2101FY) and ( 2201FY) (3-fig. 7) (Refer to TASK 31-42-01-900-801).
(d) Install the new AGM modules ( 2101FD) and ( 2201FD) (4-fig. 7) (Refer to TASK 31-60-17-900-801).
(e) Install the new processor 10 module ( 2051FY) P/N 7034056-1903 in slot 13 (in place of the EGPWS 1 module) (5-fig. 7) (Refer to TASK 31-41-09-900-802).
(f) Install the new power supply modules ( 1101FY) and ( 1201FY) (6-fig. 7) (Refer to TASK 31-41-05-900-801).
(g) Install the new generic I/O modules ( 4101FY), (4201FY) and ( 4501FY) (7-fig. 7) (Refer to TASK 31-42-13-900-801).
NOTE: P/N for generic I/O 5 module is different from other generic I/O modules (see table in 3.A. for detail).
(h) Install the new control/video I/O 1 module ( 3101FY) (8-fig. 7) (Refer to TASK 31-42-09-900-801).
(i) Re-install the other MAU 1 modules (Refer to TASK 31-41-01-900-801).
(j) Remove and replace the MAU 1 ASCB bus coupler module ( 5101FY) (Refer to TASK 31-42-17-900-801).
FALCON 7X 7X -602 June 03, 2024 ATA 00 Initial issuance Page 9 / 42 DASSAULT AVIATION Proprietary Data
(5) Do the following steps on MAU 2:
(a) Remove and replace the NIC/processor modules (2301FY) and ( 2401FY) (3-fig. 7 ) (Refer to TASK 31-42-01-900-801).
(b) Remove and replace the AGM modules ( 2301FD) and ( 2401FD) (4-fig. 7) (Refer to TASK 31-60-17-900-801).
(c) Remove and replace the power supply modules ( 1301FY) and ( 1401FY) (6-fig. 7) (Refer to TASK 31-41-05-900-801).
(d) Remove and replace the generic I/O modules ( 4301FY) and ( 4401FY) (7-fig. 7) (Refer to TASK 31-42-13-900-801).
(e) Remove and replace the control I/O 2 module ( 3201FY) (9-fig. 7) (Refer to TASK 31-42-05-900-801).
(f) Remove and replace the MAU 2 ASCB bus coupler module ( 5201FY) (Refer to TASK 31-42-17-900-801).
(6) Remove and replace the NIM modules ( 1101NZ) and ( 1201NZ) (Refer to TASK 31-43-05-900-801).
(7) Replace the lower TCAS antenna as follows:
(a) Remove the fuel equipment bay door ( 151AL) (Refer to TASK 53-60-00-900-801).
(b) Remove the lower TCAS antenna (303NP) from the fuel equipment bay door (Refer to TASK 34-44-05-900-801).
(c) Apply aircraft paint finish on the new fuel equipment bay door ( 151AL) (item 1) in accordance with the Protection Scheme (Refer to SDS 20-60-00).
(d) Using new screws (item 2) and washers (item 3), install the new lower TCAS antenna (503NP) (item 4) on the new fuel equipment bay door (Refer to TASK 34-44-05-900-801).
(e) Install the new fuel equipment bay door (151AL) (Refer to TASK 53-60-00-900-801).
(8) External access only: replace the upper TCAS antenna following fig. 8:
(a) Remove the upper TCAS antenna ( 203NP) from the fuselage (Refer to TASK 34-44-05-900-801) and retrieve the eight screws and washers.
(b) Remove the microballon taper shim specific to the old antenna.
(c) Prepare the work area:
• use a Plexiglas spatula to remove sealant to obtain a clean surface,
• clean the work area with lint-free cloth moistened with cleaner.
(d) Protect both exposed lateral flange outer shims (a-fig. 8 ) with alodine (Refer to TASK 20-60-00-370-801) and anti-corrosion primer (Refer to SDS 20-60-00).
(e) With the help of a template (local procurement), create a microballon taper shim using compound EC 3524 (b-fig. 8).
(f) Apply 5 mm interlaying sealant on the existing outer shim (c-fig. 8) all along the internal (dfig. 8) and external (e-fig. 8) borders (Refer to TASK 20-32-00-390-801).
(g) Apply an interlay of interlaying sealant between the new shim and the fuselage (f-fig. 8 ) (Refer to TASK 20-32-00-390-801).
FALCON 7X 7X -602 June 03, 2024 ATA 00 Initial issuance Page 10 / 42 DASSAULT AVIATION Proprietary Data