TextPartly OCR
Some pages are OCR from a scan. OCR can misread letters and numbers.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'a52aabfa2a151936c942544787f26bed9d7a98c68b807064742de5216422c8e5' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'a52aabfa2a151936c942544787f26bed9d7a98c68b807064742de5216422c8e5' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
FALCON 10 No 337 MARCH 22, 2019
MANDATORY ATA 27-36
FLIGHT CONTROLS
HYDRAULIC SYSTEM HYDRAULIC #2 PIPE ROUTING AND PROTECTION
FALCON SERVICE BULLETIN Copyright © 2019 by Dassault Aviation All rights reserved. No part of this work may be reproduced or copied in any form or by any means without written permission of Dassault Aviation.
FLIGHT CONTROLS
HYDRAULIC SYSTEM HYDRAULIC #2 PIPE ROUTING AND PROTECTION Initial issuance March 22, 2019 List of effective pages :
1 to 10 FALCON 10 F10 -337 F10 -27-36
FLIGHT CONTROLS
HYDRAULIC SYSTEM HYDRAULIC #2 PIPE ROUTING AND PROTECTION
1. PLANNING INFORMATION A. EFFECTIVITY This Service Bulletin is applicable to all FALCON 10 aircraft.
B. REASON In the wings, interference between rib passage hole (Rib 1 to Rib 2a) and hydraulic #2 pipes and chafing between pipes has been identified.
The purpose of this Service Bulletin is to suppress interference at rib passage hole and chafing along the hydraulic #2 pipe.
C. DESCRIPTION The Service Bulletin is divided into two sections:
Section F10-337-1:
The operation consists in checking:
• no interference between ribs passage hole (Rib 1 to Rib 2a) and hydraulic #2 pipes
• no chafing between pipes.
Section F10-337-2:
The operation consists in installing spiral binding on pipe forward of ribs passage hole and adding a grommet around ribs passage hole.
D. COMPLIANCE This Service Bulletin is mandatory as prescribed by the Airworthiness Authorities of the country of registration of the aircraft.
E. APPROVAL This Service Bulletin covers DASSAULT AVIATION modification F10 M953 that has been approved under the authority of DOA nr. EASA.21J.051.
The technical content of this document is approved under the authority of DOA nr. EASA.21J.051.
F. LABOR Estimated labor-hours: Refer to Service Bulletin Commercial Summary.
NOTE: These labor-hours only concern the work described in this Service Bulletin and do not include other maintenance work that may be performed on this occasion.
G. MATERIAL - PRICE AND AVAILABILITY The modification kit may be obtained from either address listed below:
FALCON 10 F10 -337 March 22, 2019 F10 -27-36 Initial issuance Page 1 / 10 DASSAULT AVIATION Proprietary Data
Western hemisphere: DASSAULT FALCON JET CORP.
SPARES DISTRIBUTION CENTER 200 RISER ROAD LITTLE FERRY, NJ 07643 U.S.A.
Telephone:
• CANADA and U.S.A.: 1-800-800-4036
• MEXICO: 001-800-800-4036
• Other countries: 1-201-541-4809 Fax:
• CANADA and U.S.A.: 1-800-800-4817
• MEXICO: 001-800-800-4817
• Other countries: 1-201-440-7021 Other continents: DASSAULT AVIATION Falcon Spares 54, AVENUE MARCEL DASSAULT B.P. 24 33701 MERIGNAC Cedex (FRANCE) Please contact your Dassault Aviation Account Representative Telephone: 33 (0)5.56.18.44.44 E/H dafsorders@dassault-aviation.com Price and availability on request.
H. WEIGHT AND BALANCE Change in weight: None.
Change in balance with respect to 25% MAC: None.
I. REFERENCES Aircraft Maintenance Manual:
• 7-10-00 - AIRCRAFT JACKING
• 20-00-05 - SUMMARY OF MANDATORY PRECAUTIONS TO BE TAKEN DURING AIRCRAFT
MAINTENANCE OPERATIONS
• 29-00-01 - SERVICING - INSTRUCTIONS FOR REPLACEMENT OF A HYDRAULIC
COMPONENT
• 53-50-00 - AERODYNAMIC FAIRINGS
• 57-55-01 - REMOVAL/INSTALLATION REPLACEMENT OF THE FLAPS - DETAILED
INSPECTION OF THE LH AND RH INBOARD FLAP AND RIBS Stuctural repair manuel:
• 51-20-09 - BASIC SEALING METHODS
• 51-30-05 - DRILLING Illustrated Parts Catalog:
FALCON 10 F10 -337 March 22, 2019 F10 -27-36 Initial issuance Page 2 / 10 DASSAULT AVIATION Proprietary Data
• 27-13-05-01 - SYSTEM ASSEMBLY - SERVO HYDRAULIC J. OTHER PUBLICATIONS AFFECTED None.
FALCON 10 F10 -337 March 22, 2019 F10 -27-36 Initial issuance Page 3 / 10 DASSAULT AVIATION Proprietary Data
2. ACCOMPLISHMENT INSTRUCTIONS A. GENERAL INSTRUCTIONS AND SAFETY PRECAUTIONS
(1) Obey the Structural Repair Manual:
• Basic sealing methods (Refer to SRM 51-20-09).
• Drilling (Refer to SRM 51-30-05).
B. PRELIMIRARY STEPS
(1) The aircraft must be in the maintenance configuration (Refer to procedure 20-00-05).
(2) Remove the LH and RH inboard flaps (Refer to procedure 57-55-01).
(3) Remove the removable protector in the LH/RH wells ( fig. 3).
C. SECTION F10-337-1: INSPECTION NOTE: The procedure is applicable to LH and RH wings. Operations are described at LH wing (RH wing is symmetrical).
(1) Check that there is fig. 1:
• no interference between hydraulic #2 pipes (items 260-430 LH side IPC 27-13-05 FIGURE
1), and Rib 1 to Rib 2a passage hole,
• no chafing between hydraulic #2 pipes (items 260-430 LH side IPC 27-13-05 FIGURE 1),
• no interference with pipe F10A758451 and bellcranck on right side.
(a) If no interference and no chafing are found, install :
• grommet on Rib 1c and 2a passage hole with sealant for bonding purpose,
• spiral binding along the two pipes betwween Rib 1b and Rib 2a in accordance with fig.
2.
(b) If interference or chafing is found, applied SECTION F10-337-2.
D. SECTION F10-337-2: CHECK PIPES AND ADD PROTECTIONS NOTE: The procedure is applicable to LH and RH wings. Operations are described at LH wing (RH wing is symmetrical).
(1) Jack the aircraft (Refer to procedure 7-10-00).
(2) Remove Rear lateral fairing 175JL/175JR (Refer to procedure 53-50-00).
(3) Remove the riveted wing lower panel at track 1 ( fig. 3) and (fig. 4).
CAUTION: TAKE CARE NOT TO OVALIZE THE BORES IN THE SKIN AND SUB-STRUCTURE WHEN COUNTERDRILLING FASTENERS.
NOTE: Control the bores to determine the out-of tolerances to provide oversize fasteners.
(4) Remove the pipes (items 260/270 and 430/440) (Refer to IPC 27-13-05 Fig. 1) and (Refer to procedure 29-00-01).
NOTE: Mark the pipes in front of Rib 1b.
FALCON 10 F10 -337 March 22, 2019 F10 -27-36 Initial issuance Page 4 / 10 DASSAULT AVIATION Proprietary Data
After removal, check that there are no marks or chafing on pipes:
• If no marks and no chafing are found, go to step 2.C.(2).
• If marks or chafings on pipes are found, determine the depth of mark as follows:
• If depth ≤ 0.1 mm (0.004 in), smooth the surface with water abrasive paper within tolerance limit.
• If depth > 0.1 mm (0.004 in), discard the pipe.
(5) Install grommet edging on holes Rib 1 (side Rib 1a), Rib 1a, Rib 1c and 2a with sealant for bonding purpose (fig. 2).
(6) Install spiral binding along the two pipes in accordance with fig. 2.
(7) Install the pipes (items 260/270 and 430/440) (Refer to IPC 27-13-05 Fig. 1) and (Refer to task 29-00-01), at Rib 1b, the clamps must be installed in accordance with fig. 2.
(8) Install the lower panel at track 1 with interlaying sealant. The fasteners are installed with interlaying sealant under the head (fig. 4).
NOTE: If some bores are out-of tolerance, enlarge to repair size.
E. FINAL STEPS
(1) Install Rear lateral fairing 175JL/175JR (Refer to procedure 53-50-00-0).
(2) Install the removal protector in the LH/RH well ( fig. 3).
(3) Install the LH and RH inboard flaps (Refer to procedure 57-55-01).
F. RECORDING Record compliance with this Service Bulletin in the appropriate aircraft documents.
Fill out the card located at the end of the Service Bulletin and mail or fax it to Dassault Aviation or Dassault Falcon Jet, or fill out the electronic Service Bulletin reply form located in the ”Service Bulletin" page on the Falcon portal.
FALCON 10 F10 -337 March 22, 2019 F10 -27-36 Initial issuance Page 5 / 10 DASSAULT AVIATION Proprietary Data
3. MATERIAL INFORMATION NOTE: Compliance with this Service Bulletin by substituting the part numbers below with interchangeable subsequent part numbers (as per the Master List) is acceptable, provided that subsequent part numbers have the same effectivity as the original ones.
A. MODIFICATION KIT Kit P/N SBF10-0337A
NEW P/N QTY KEY WORD SBPTFE4 or SP-PTFE 5 m Spiral binding MS21266-1T 2 Grommet edge Replacement of pipes
NEW P/N QTY KEY WORD F10A758301 1 LH pipe (return) F10A758351 1 LH pipe (pressure) F10A758401 1 RH pipe (return) F10A758451 1 RH pipe (pressure) Kit P/N SBF10-0337B for Rear lateral fairing installation NOTE: If the LH and RH are removed two kits are necessary
NEW P/N QTY KEY WORD ITEM-FIG NAS1921M05S02WU 18 Blind rivet (1-fig. 4) NAS1921M05S03WU 3 Blind rivet (2-fig. 4) MS90353S0604 1 Blind bolt (3-fig. 4) 21218DE3210 97(+10) Rivet (4-fig. 4) 21218DE4010 21(+5) Rivet (5-fig. 4) B. LOCAL PROCUREMENT As indicated in Consumable Products Manual (CPM):
• water abrasive paper
• sealant for bonding purpose FALCON 10 F10 -337 March 22, 2019 F10 -27-36 Initial issuance Page 6 / 10 DASSAULT AVIATION Proprietary Data
DASSAULT SERVICE BULLETIN
AVIATION FALCON 10 F10 -337 Rib 2a Rib1c Rib1b Rib1a Rib1
LH SIDE / RH SYMMETRICAL Passage hole Rib1 Passage hole Rib1a Passage hole Rib 1b Passage hole Rib1c Passage hole Rib2a Passage hole Rib1 RH SIDE Interference between bellcranck and pipe.
Figure 1: LH SIDE INSPECTION March 22. 2019 F10-27-36 Initial issuance Page 7 / 10
DASSAULT SERVICE BULLETIN
AVIATION FALCON 10 F10 -337 Rib 1 Rib 1a Rib 1b Rib 1c Rib 2a 50(2 in.) 50 (2 in.) 100(4 in.) _ Section with spiral binding Section with spiral binding Grommet installation Rib 1b clamps installation Figure 2: SPIRAL BINDING AND GROMMET INSTALLATION March 22, 2019 F10 -27-36 Initial issuance Page 8 / 10
DASSAULT SERVICE BULLETIN
AVIATION FALCON 10 F10 -337 Removable protector Riveted wing Jower panel F/C23 Rail 1 False spar datum line F/C21 F/C22 - Rib 1a
- Rib 1b Fairing door Figure 3: WING LOWER PANEL LOCATION March 22, 2019 F10 -27-36 Initial issuance Page 9 / 10
DASSAULT SERVICE BULLETIN
AVIATION FALCON 10 F10 -337 * * * ‡ ‡ Detail applicable for LH side only LH skin looking up (RH side symmetric except detail) ) * Rivet F 100° dia 32 ) * Rivet F 100° dia 32 - countersunk rivetting * Rivet F 100° dia 4 * Rivet MLS F 100° dia 397 4 Rivet HUCK dia 4 76
• Screw F 100° dia 48 VIS Figure 4: WING LOWER PANEL FASTENERS March 22, 2019 F10 -27-36
END OF DOCUMENT Initial issuance Page 10 / 10