Copy · U.S. DOT/FAA - Service Bulletin 110-27-A095 · 16 pages

© Embraer S.A. Filed by the FAA in regulations.gov docket FAA-2014-0740, the docket of AD 2014-20-05. Not covered by OpenAirDocs’ CC0 dedication.

TextOCR

This text is OCR from a scan. OCR can misread letters and numbers.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '3e93d694d052bb2aab232b83dbdf3167945db5bf7b92a13ee1c3545d1a08d934'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Page 1OCROpen in PDF

- EMBRAER ALERT

SERVICE BULLETIN in connection with the use of this document, Embraer does not provide any express or implied warranties and expressly disclaims any warranty of merchantability or fitness for a particular purpose.

FLIGHT CONTROLS - INSPECTION OF THE RUDDER TRIM TAB ACTUATOR

1. PLANNING INFORMATION A. SB EFFECTIVITY Aircraft affected:

MODEL SN EMB-110 - BANDEIRANTE All aircraft in operation equipped with the affected Part Number.

Affected component:

Rudder Trim Tab Actuator Part Numbers 110P2-506-10-09-36, 110P2-506-10-09-37, and 110P2-506-10-09-38 installed in the aircraft or in stock as spare.

NOTE: This effectivity list includes the aircraft originally equipped with the affected component. Since this component is a "Line Replaceable Unit" (LRU), it may be necessary to refer to the fleet maintenance control record and verify whether the unit has not been replaced with another one during routine maintenance.

In-production effectivity:

The subject presented in this bulletin does not affect any in-production aircraft.

B. CONCURRENT REQUIREMENTS None.

REVISION No.: DATE: 21/Aug/2014 ALERT SB No.: 110-27-A095 PAGE: 1 of 15 Copyright © 2014 by EMBRAER - All rights reserved.

Page 2OCROpen in PDF

- EMBRAER ALERT

SERVICE BULLETIN C. REASON Embraer was informed about an event of high level vibration and difficulty of controllability during an Embraer-110P1 flight that required the crew to do a forced landing.

The investigation identified a condition of a severe internal at the rudder trim tab actuator fork end, which was found disconnected, making the rudder trim tab loose.

Also, the rudder horn mass balance was lost.

This Alert Service Bulletin gives the instructions to inspect the rudder trim tab actuator components for signs of corrosion, with emphasis on its spring and fork end.

D. DESCRIPTION This Bulletin is divided into 2 PARTS, as follows:

PARTI INSPECTION OF THE RUDDER TRIM TAB ACTUATOR COMPONENTS Applicable to: Service Bulletin Effectivity.

PART I of this bulletin presents a Detailed Inspection (DI) for signs of corrosion in the Rudder Trim Tab Actuator components, specifically on its Spring and Fork End installed in Rudder Trim Tab Actuator.

a) If no signs of corrosion in the Spring and Fork End are detected, the components cleaning and protection against corrosion by the application of a corrosion inhibitive compound is required;

b) If any signs of corrosion is detected in the Spring and Fork End, replace these components by the accomplishment of Part Il of this Bulletin.

To do this, it is necessary to remove the Rudder Trim Tab Actuator from the aircraft and perform the inspection on the bench.

NOTE: During the inspections mentioned in this PART I, the corrosion level identification may be different depending on the component to be inspected.

The time for accomplishment of PART Il of this Bulletin is also different depending on the level of the corrosion of each component. For this, refer to Section 1.E. TIME FOR ACCOMPLISHMENT below for a detailed instructions for corrosion level identification.

PAGE: 2 SB No.: 110-27-A095 ALERT DATE: 21/Aug/2014 REVISION No.:

Copyright © 2014 by EMBRAER - All rights reserved.

Page 3OCROpen in PDF

• EMBRAER ALERT

SERVICE BULLETIN Embraer is providing the necessary support for the accomplishment of this Bulletin with the Embraer Technical Representatives or through Embraer Fleet Technical Center. Refer to Section 2.B. INDUSTRY SUPPORT INFORMATION for Embraer contact information.

PART II REPLACEMENT OF THE SPRING AND FORK END Applicable to: Service Bulletin Effectivity.

PART Il of this bulletin consists in replacing the Spring and Fork End installed in Rudder Trim Tab Actuator.

To do this, it is necessary to remove the Rudder Trim Tab Actuator from the aircraft and perform the modification on the bench.

E. TIME FOR ACCOMPLISHMENT

(1) Applicable to PART I Embraer recommends that PART I of this bulletin be accomplished within the next 10 flight hours or 15 calendar days, whichever occurs first, after the release date of this Service Bulletin.

NOTE: If any report of vibration is detected, Embraer recommends the accomplishment of PART I of this Service Bulletin before the next flight.

DATE: 21/Aug/2014 REVISION No.: ALERT SB No.: 110-27-A095 PAGE: 3 Copyright © 2014 by EMBRAER - All rights reserved.

Page 4OCROpen in PDF

- EMBRAER ALERT

SERVICE BULLETIN

(2) Applicable to PART II

(a) Applicable for the Fork End (Aluminum) - Internal and External surface

CORROSION CORROSION ACTION / TIME FOR

LEVEL CARACTERIZATION ACCOMPLISHMENT Characterized by a surface color - Clean the surface with change different from the original Methyl Ethyl Ketone (MEK) aspect. Normally these affected apply Corrosion areas present dark gray coloration. Inhibitor Compound Dinitrol Visually examining the surface it is AV 15 or AV 30 (or any Surface oxidation or not possible to detect pitting under Spec. MIL-PRF- discoloration indications. When scribing the 16173) in the Fork End affected surface with a suitable Bore immediately after the tool, it is possible to observe that accomplishment of PART I the indication is just superficial with of this Bulletin.

no deep indication. Use suitable tool like acrylic/plastic razor to avoid scratches in the surface.

- Clean the surface with Methyl Ethyl Ketone (MEK) and apply Corrosion Inhibitor Compound Dinitrol AV 15 or AV 30 (or any under Spec. MIL-PRF- Light Corrosion 16173) in the Fork End (Local pitting Characterized by single pitting Bore immediately after the corrosion not indications not concentrated in a accomplishment of PART I located in the cross specific area and not located in the of this Bulletin, and then;

hole boundaries) cross holes boundaries.

- Replace the Fork End by the accomplishment of PART Il 150 flight hours or 03 calendar months (whichever occurs first) after the accomplishment of PARTI.

Severe Corrosion (Multiple pitting Characterized by multiple - Replace the Fork End by corrosion or pitting concentrated pitting indications in accomplishment of located in the cross any surface of the part or by single PART II of this Bulletin hole boundary) cross hole boundary. pitting indication located in immediately accomplishment of PART I.

SB No.: 110-27-A095 ALERT DATE: 21/Aug/2014 PAGE: 4 REVISION No.:

Copyright © 2014 by EMBRAER - All rights reserved.

Page 5OCROpen in PDF

- EMBRAER ALERT

SERVICE BULLETIN

(b) Applicable for the Spring (Steel)

CORROSION CORROSION ACTION / TIME FOR

LEVEL CARACTERIZATION ACCOMPLISHMENT Characterized by a surface color Clean the surface with change different from the original Methyl Ethyl Ketone (MEK) aspect. Normally these affected to remove the residues and areas present a reddish to brown apply Corrosion Inhibitor Surface oxidation or or dark coloration. When scribing Compound Dinitrol AV 15 discoloration: tool, it is possible to observe that the affected surface with a suitable or AV 30 (or any under Spec. MIL-PRF-16173) in the indication is just superficial the Fork End Bore without evidence of material immediately after the removal. Use suitable tool like accomplishment of PART I acrylic/plastic razor to avoid of this Bulletin.

scratches in the surface.

Sand Smoothly the affected areas, clean the surface to remove the Characterized by local reddish to residues and apply brown indications without evidence Corrosion Inhibitor of thickness reduction. Scribing the Compound Dinitrol AV 15 surface with a suitable tool it is or AV 30 (or any under possible to observe changes in the Spec. MIL-PRF-16173) in Light Corrosion: indication area and surrounding surface roughness between the the spring immediately after the accomplishment of surfaces, but there is no deep PART I of this Bulletin, and indication. Use suitable tool like then.

scratches in the surface. acrylic/plastic razor to avoid - Replace the Spring by the accomplishment of PART II 150 flight hours or 03 months (whichever occurs first) after the accomplishment of PART I Characterized by overall reddish to brown indications with evidence of thickness reduction or residues Severe Corrosion: possible to observe deep the surface with a suitable tool it is due to material exfoliation. Scribing accomplishment of PART II of this Bulletin immediately Replace the Spring by the indications with evidence of after the accomplishment of thickness reduction. Use suitable PARTI.

tool like acrylic/plastic razor to avoid scratches in the surface.

REVISION No.: DATE: 21/Aug/2014 ALERT SB No.: 110-27-A095 PAGE: 5 Copyright © 2014 by EMBRAER - All rights reserved.

Page 6OCROpen in PDF

-EMBRAER ALERT

SERVICE BULLETIN F. APPROVAL The technical aspects of this Alert Service Bulletin are approved by: Embraer - Engineering Board.

G. COMMUNICATIONS TO EMBRAER EMBRAER requests that any results found during these inspections be informed to your local EMBRAER representatives or offices.

H. ESTIMATED MANPOWER This estimate is for direct labor only, performed by experienced personnel, and does not include the time to plan, prepare, or inspect the work.

it is assumed that all the tools, parts, and other means are readily available when necessary.

This estimate does not include the sealant, paint, or adhesive curing time.

-Access opening: 1.0 man- hour.

- Inspection: 1.5 man- hours.

-Modification: 3.0 man- hours.

-Access closure: 1.0 man- hour.

-Test: 1.0 man-hour.

I. WEIGHT AND BALANCE -Change in basic weight: None.

-Change in basic moment: None.

J. REFERENCES T.O. 1C95A-2-5 - "Maintenance Manual" - Flight Controls.

T.P. 27-00-01/702 - Component Maintenance Manual.

SB No.: 110-27-A095 PAGE: 6 ALERT DATE: 21/Aug/2014 REVISION No.:

Copyright © 2014 by EMBRAER - All rights reserved.

Page 7OCROpen in PDF

-EMBRAER ALERT

SERVICE BULLETIN K. OTHER PUBLICATIONS AFFECTED None.

2. MATERIAL INFORMATION A. MATERIAL - PRICE AND AVAILABILITY

(1) MATERIAL AVAILABLE FROM EMBRAER None.

(2) MATERIAL AVAILABLE FROM OTHER VENDORS None.

B. INDUSTRY SUPPORT INFORMATION Embraer can provide the necessary support for the accomplishment of this Bulletin with the Embraer Technical Representatives or through Return to Service.

See address below:

EMBRAER S.A.

ATT.: Return to Service - RTS.

Phone: +55 12 3927 7334 or +55 12 99121 2022.

E-mail: rts@embraer.com.br REVISION No.: DATE: 21/Aug/2014 ALERT SB No.: 110-27-A095 PAGE: 7 Copyright © 2014 by EMBRAER - All rights reserved.

Page 8OCROpen in PDF

-EMBRAER ALERT

SERVICE BULLETIN C. MATERIAL NECESSARY FOR EACH AIRCRAFT

(1) MATERIAL TO BE PROCURED - Applicable to Part Il only

(a) PARTS The parts below should be ordered as spares from Embraer. For this, check the Rudder Trim Tab Actuator Part Number before ordering the Parts.

Applicable for Rudder Trim Tab Actuator PN 110P2-506-10-09-36 and 110P2- 506-10-09-38

NEW PN DESCRIPTION OLD PN QTY DISP 110P2-506-10-09-28-03 Fork End 110P2-506-10-09-28-03 01 7 120-09954-001 Spring 120-09954-001 01 7 PE49073-1 Neoprene Sleeve PE49073-1 01 Tla

(a) Replace the Neoprene Sleeve only if it is damaged.

Applicable for Rudder Trim Tab Actuator PN 110P2-506-10-09-37

NEW PN DESCRIPTION OLD PN QTY DISP/ Note 110P2-506-10-09-29-02 Fork End 110P2-506-10-09-29-02 01 7 120-09954-001 Spring 120-09954-001 01 7 PE49073-1 Neoprene Sleeve PE49073-1 01 71a

(a) Replace the Neoprene Sleeve only if it is damaged.

(b) CONSUMABLES The material below or equivalent, required for the accomplishment of this bulletin, should be procured from the operator's inventories or from a local supplier.

ITEM PN DESCRIPTION QTY DISP Methyl Ethyl Ketone (Spec. ASTM-D-740) Solvent AR 6 DINITROL AV-30 (Spec. MEP10-063) Corrosion-inhibiting compound AR 6 DINITROL AV-15 Corrosion-inhibiting compound AR 6 Spec. MIL-PRF-16173 Corrosion-inhibiting compound AR 6 SB No.: 110-27-A095 ALERT DATE: 21/Aug/2014 PAGE: 8 REVISION No.:

Copyright © 2014 by EMBRAER - All rights reserved.

Page 9OCROpen in PDF

TEMBRAER ALERT

SERVICE BULLETIN QUANTITY:

AR = As Required.

DISPOSITION:

6 = Apply as required 7 = Replace with part bearing same PN D. MATERIAL NECESSARY FOR EACH SPARE None.

E. REIDENTIFIED PARTS None.

F. TOOLING - PRICE AND AVAILABILITY None.

DATE: 21/Aug/2014 REVISION No.: ALERT SB No.: 110-27-A095 PAGE: 9 Copyright © 2014 by EMBRAER - All rights reserved

Page 10OCROpen in PDF

- EMBRAER ALERT

SERVICE BULLETIN

3. ACCOMPLISHMENT INSTRUCTIONS NOTES: 1) For the purpose of this Service Bulletin, a Detailed Inspection (DI) is: "An intensive examination of a specific item, installation or assembly to detect damage, failure or irregularity. Available lighting is normally supplemented with a direct source of good lighting at an intensity deemed appropriate.

Inspection aids such as mirrors, magnifying lenses, etc. may be necessary. Surface cleaning and elaborate access procedures may be required."

2) Obey all of the WARNINGS and CAUTIONS included in the referenced manuals and procedures.

3) The Manuals and other documents are referred to by means of acronyms or using a simplified form. Refer to section "1. I. REFERENCES" for a more complete definition.

The steps below outline the general accomplishment instructions.

The detailed sequence is included in the respective figure, when necessary.

A. Make sure that the aircraft is safe for maintenance.

B. PART I - INSPECTION OF THE RUDDER TRIM TAB ACTUATOR COMPONENTS

(1) Remove the Rudder Trim Tab Actuator from the aircraft following the instructions of T.O. 1C95A-2-5 - "Maintenance Manual" - Flight Controls.

On the Bench, disassemble the Rudder Trim Tab Actuator by following the instructions mentioned in T.P. 27-00-01/702 - Component Maintenance Manual with Illustrated Part List - Disassembly Section. Refer to Figure 1.

(3) Clean the components with the aid of a nylon brush wet with Methyl Ethyl Ketone (ASTM-D-740) MEK.

(4) Do a Detailed Inspection in the Fork End and in the Spring for signs of corrosion and then Refer to Table 1 and Table 2 to identify the applicable action.

SB No.: 110-27-A095 ALERT DATE: 21/Aug/2014 PAGE: 10 REVISION No.:

Copyright © 2014 by EMBRAER - All rights reserved.

Page 11OCROpen in PDF

-EMBRAER ALERT

SERVICE BULLETIN

(a) Applicable for the Fork End (Aluminum) - Internal and External surface

CORROSION LEVEL ACTION

- After cleaning, apply a corrosion inhibitor Surface oxidation or compound Dinitrol AV-15 or AV-30 (or any under discoloration: Spec. MIL-PRF-16173) in the Fork End bore.

Local pitting corrosion outside the cross hole boundaries:

Multiple pitting corrosion or pitting around the cross hole:

- After cleaning, apply a corrosion inhibitor compound Dinitrol AV-15 or AV-30 (or any under Spec. MIL-PRF-16173) in the Fork End bore;

- Replace the Fork End by the accomplishment of PART Il of this SB in the next 150 flight hours or 03 months (whichever occurs first).

- Replace the Fork End by the accomplishment of PART Il of this Bulletin immediately after the accomplishment of PART I.

TABLE 01

(b) Applicable for the Spring (Steel)

CORROSION LEVEL ACTION

- After cleaning, apply a corrosion inhibitor Surface oxidation or compound Dinitrol AV-15 or AV-30 (or any under discoloration: Spec. MIL-PRF-16173) in the Fork End bore.

- Sand smoothly the spring surface, clean the surface using Methyl Ethyl Ketone or equivalent and then apply Dinitrol AV-15 or AV-30 (or any under Spec. MIL-PRF-16173) to the Spring surface Light Corrosion:

- Replace the Spring by the accomplishment of PART Il of this SB in the next 150 flight hours or 03 months (whichever occurs first).

Replace the Spring by the accomplishment of Severe Corrosion: PART Il of this Bulletin immediately after the accomplishment of PART I.

TABLE 02 DATE: 21/Aug/2014 REVISION No.: ALERT SB No.: 110-27-A095 PAGE: 11 Copyright © 2014 by EMBRAER - All rights reserved.

Page 12OCROpen in PDF

- EMBRAER ALERT

SERVICE BULLETIN Assembly the Rudder Trim Tab Actuator by following the instructions mentioned in T.P. 27-00-01/702 - Component Maintenance Manual with Illustrated Part List - Assembly Section.

NOTE 1: During the Assemble of the Rudder Trim Tab Actuator apply Dinitrol AV-15 or AV-30 (or any under Spec. MIL-PRF-16173) inside the terminal bore.

NOTE 2: If the neoprene sleeve PN PE49073-1 was found damaged, replace it using a new neoprene sleeve with the same Part Number.

(6) Reinstall the Rudder Trim Tab Actuator to the aircraft following the instructions of T.O. 1C95A-2-5 - "Maintenance Manual" - Flight Controls.

NOTE: After reinstallation do an operation check-out and the trim tabs maximum allowable backlash checkout as described in the Maintenance Manual.

C. PART II - REPLACEMENT OF THE SPRING AND FORK END

(1) Remove the Rudder Trim Tab Actuator from the aircraft.

On the Bench, disassembly the Rudder Trim Tab Actuator by following the instructions mentioned in T.P. 27-00-01/702 - Component Maintenance Manual with Illustrated Part List - Disassembly Section. Refer to Figure 1.

(3) Replace the Fork End and/or Spring by the same Part Number.

(4) Assemble the Rudder Trim Tab Actuator by following the instructions mentioned in T.P. 27-00-01/702 - Component Maintenance Manual with Illustrated Part List - Assembly Section. Refer to Figure 1.

NOTE 1: During the Assemble of the Rudder Trim Tab Actuator apply Dinitrol AV-15 or AV-30 (or any under Spec. MIL-PRF-16173) inside the terminal bore.

NOTE 2: If the neoprene sleeve PN PE49073-1 was found damaged, replace it using a new neoprene sleeve with the same Part Number.

(5) Reinstall the Rudder Trim Tab Actuator to the aircraft following the instructions of T.O. 1C95-A-2-5 - "Maintenance Manual" - Flight Controls.

NOTE: After reinstallation do an operation check-out and the trim tabs maximum allowable backlash checkout as described in the Maintenance Manual.

PAGE: 12 SB No.: 110-27-A095 ALERT DATE: 21/Aug/2014 REVISION No.:

Copyright © 2014 by EMBRAER - All rights reserved

Pages 13–16 of 16