Copy · U.S. DOT/FAA - SBF100-51-021 · 25 pages

© Fokker. Filed by the FAA in regulations.gov docket FAA-2014-0492; AD 2015-12-12 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

TextPartly OCR

Some pages are OCR from a scan. OCR can misread letters and numbers.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = 'cb0979e6b3d530a560704154cc2c1ef74608566063255ad92555fa851eca626b'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Service Bulletin Fokker 70/100

Page 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Revision - - - - - - - - - - - - - - - - - Page 18 19 20 Revision - - - Attachments PLL and PLS. For a detailed listing refer to page 6.

Apr 23/13 SBF100-51-021 Page 1

Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement.

Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted except with the prior written permission of Fokker Services B.V.

STANDARD PRACTICES AND STRUCTURES-GENERAL General - The Introduction of Drain Tubes on the Center Wing Rear Spar

1. Planning Information A. Effectivity

(1) F28 Mark 0070/0100 aircraft serial numbers:

11244 thru 11585 B. Concurrent Requirements

(1) Not applicable.

C. Reason

(1) In case of a water accumulation on the top of the center wing torsion box inside the cabin (zones 171 and 172), the water drains through the existing drain holes/gaps in the web plates on top of the center wing rear spar via the center wing rear spar area on the aileron control cables. With the freezing temperatures normally encountered during flight ice can accumulate on the aileron control cables resulting in limited aileron control.

This modification provides drainage of the area on the top of the center wing torsion box in a location where drain water can not affect the aileron control.

Service Bulletin Fokker 70/100

SBF100-51-021 Apr 23/13 Page 2

Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement.

Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted except with the prior written permission of Fokker Services B.V.

D. Description

(1) This Service Bulletin is divided into two parts as follows:

Part 1: The Installation of Water Drain Tubes on the Center Wing Rear Spar in Aircraft with Center Wing Bag Tanks (Applicable to Aircraft Serial Numbers 11244 thru 11441) This Part tells you how to:

- remove the passenger seats at the location of the modification;

- remove the carpet at the location of the modification;

- remove the floor panels at the location of the modification;

- clean the area of the modification;

- prepare the water drain tube feed through holes in the affected web plates on top of the center wing rear spar;

- install the water drain tubes and identification placards;

- seal the existing drain gaps on top of the center wing torsion box;

- reinstall the removed floor panels;

- reinstall the removed carpet;

- reinstall the removed passenger seats.

Part 2: The Installation of Water Drain Tubes on the Center Wing Rear Spar in Aircraft with an Integral Center Wing Tank or Provisions for an Integral Center Wing Tank (Applicable to Aircraft Serial Numbers 11442 thru 11585) This Part tells you how to:

- remove the passenger seats at the location of the modification;

- remove the carpet at the location of the modification;

- remove the floor panels at the location of the modification;

- clean the area of the modification;

- prepare the water drain tube feed through holes in the affected web plates on top of the center wing rear spar;

- install the water drain tubes and identification placards;

- reinstall the removed floor panels;

- reinstall the removed carpet;

- reinstall the removed passenger seats.

E. Compliance

(1) Recommended.

Fokker Services recommends the accomplishment of this Service Bulletin within 3 years after the date of issue of this Service Bulletin.

NOTE: It is expected that EASA will issue an Airworthiness Directive (AD) with respect to this subject with the same compliance terms. Refer to the EASA website for the publication of a Proposed Airworthiness Directive for comments.

Service Bulletin Fokker 70/100

Apr 23/13 SBF100-51-021 Page 3

Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement.

Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted except with the prior written permission of Fokker Services B.V.

F. Approval

(1) The technical content of this document is approved under the authority of DOA nr.

EASA.21J.059.

G. Manpower

(1) Approximately 8,0 man-hours are necessary to do Part 1 or Part 2 of this Service Bulletin on one aircraft.

This table of manpower will help you to schedule and do this Service Bulletin:

Instructions Men Man-hours Elapsed time (hours) Removal 2 2,0 2,0 Modification Inspection 2 4,0 4,0 Installation 2 2.0 2,0 Testing - - - Total 8,0 8,0 NOTE: This estimate does not include the time necessary for the paint to dry and/or the sealant to cure.

(2) The estimated hours are for direct labor done by experienced personnel. They are calculated based on the conditions given in SBF100-00-001 (Service Bulletin Introduction, section 2.C., "Manpower").

H. Weight and Balance

(1) Weight change: None Index change: None.

I. Electrical Load Data

(1) Not changed.

J. Software Accomplishment Summary

(1) Not applicable.

Service Bulletin Fokker 70/100

SBF100-51-021 Apr 23/13 Page 4

Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement.

Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted except with the prior written permission of Fokker Services B.V.

K. References

(1) Fokker 70/100 Aircraft Maintenance Manual (AMM) Fokker 70/100 Structural Repair Manual (SRM) Fokker 70/100 Illustrated Parts Catalog (IPC) Fokker Consumable Material List (CML) Fokker Standards & Process Manual (SPM) Fokker internal reference(s):

- ECR 15937

- EMI 90523.

L. Publications Affected

(1) This SB affects the publications listed below:

(a) Maintenance Documentation

- Fokker 70/100 Illustrated Parts Catalog (IPC) - chapter 11-21

- chapter 27-64 NOTE: See attached Manual Change Notification MCNM F100-160.

(b) Maintenance Programs

Not affected.

(c) Special Instructions for Continued Airworthiness (ICA)

The effect of this Service Bulletin on the special ICA is as follows:

YES NO

- Electrical Wiring Interconnection System (EWIS) - X

- Fokker 70/100 Airworthiness Limitations Section (ALS):

• Fuel Tank Safety (FTS) - X

• Damage Tolerance of Fatigue Critical Structure - X

• Certification Maintenance Requirements (CMR) - X NOTE: If “YES”, when not already incorporated, the changed ICA will be incorporated in the MRB, the Airworthiness Limitations Section (ALS) and/or the AMM document(s) within one calendar year from the date of issue of this Service Bulletin. Until then, no actions are required.

(d) Operational Documentation

Not affected.

(2) Report to Fokker Services that this SB has been carried out on the applicable aircraft.

(3) You have the possibility to send your SB feedback to Fokker Services per “Reporting Quality Form”. This form is located on the last SB page.

Service Bulletin Fokker 70/100

Apr 23/13 SBF100-51-021 Page 5

Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement.

Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted except with the prior written permission of Fokker Services B.V.

(4) For incorporation of this Service Bulletin in your documentation refer to SBF100-00-001 (Service Bulletin Introduction, section 4 “Incorporation of Service Bulletins in Documentation of Fokker Services”).

(5) Accomplishment of this SB is only complete with incorporation of the manual change(s), per the ref. MCNM/MCNO, Temporary Revision or General Revision.

M. Interchangeability or Intermixability of Parts

(1) The interchangeability of the parts is as follows:

New Part Number Keyword Old Part Number Interchangeability AS21919WCE4 Clamp MS21919WCE4 Two-way NAS6603-10 Bolt NAS1303-10 Two-way NAS6603-11 Bolt NAS1303-11 Two-way NAS6603-13 Bolt NAS1303-13 Two-way NAS6603-17 Bolt NAS1303-17 Two-way

Service Bulletin Fokker 70/100

SBF100-51-021 Apr 23/13 Page 6

Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement.

Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted except with the prior written permission of Fokker Services B.V.

2. Material Information A. Material – Price and Availability

(1) You can order the necessary parts as mod kits SB10051021-XU-A and SB10051021-XU-B.

(2) You can contact your Fokker Services Customer Support Manager for the price and lead-time of this mod kit.

B. Material Required

(1) The parts, which are necessary to complete this Service Bulletin on 1 aircraft and are not part of the mod kit are described in attachment Part List Local (PLL).

Material List Issue Description Aircraft Effectivity SB10051021-XU-A B Parts List Local (PLL) 11244 thru 11261 and 11268 thru 11275 SB10051021-XU-B A Parts List Local (PLL) 11262 thru 11267 and 11276 thru 11585

(2) The mod kit parts, which are necessary to do this Service Bulletin on 1 aircraft are described in attachment Part List Supply (PLS).

Material List Issue Description Aircraft Effectivity SB10051021-XU-A B Parts List Supply (PLS) 11244 thru 11261 and 11268 thru 11275 SB10051021-XU-B A Parts List Supply (PLS) 11262 thru 11267 and 11276 thru 11585 C. Tooling – Price and Availability

(1) Not applicable.

D. Drawings Required

(1) Not applicable.

Service Bulletin Fokker 70/100

Apr 23/13 SBF100-51-021 Page 7

Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement.

Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted except with the prior written permission of Fokker Services B.V.

3. Accomplishment Instructions

General:

- For CML material number references, refer to “MyFokkerFleet.com/Documentation” and select CML.

- For Standards and Process Manual (SPM) references, refer to “MyFokkerFleet.com/Documentation” and select SPM.

- For the application of Alodine 1201 (Fk13-003D), refer to the AMM, chapter 51-22-00.

- For the application of sealing compound PS-870A (Fk09-016A) refer to the AMM, chapter 51-23-00.

- For the removal/installation of solid rivets, refer to the SRM, chapter 51-40-02.

- For the application of Primer and Paint, refer to the AMM, chapter 51-21-00.

- For drilling and dimpling procedures, refer to the SRM, chapter 51-21-02.

WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE MATERIALS. OBEY

THE INSTRUCTIONS AND MANUFACTURER'S HEALTH AND SAFETY INSTRUCTIONS.

Part 1: The Installation of Water Drain Tubes on the Center Wing Rear Spar in Aircraft with Center Wing Bag Tanks (Applicable to Aircraft Serial Numbers 11244 thru 11441) A. Preparation Refer to figure 1.

(1) Remove the passenger seats on the LH and RH side of the cabin at the location above the center wing section (zone 171 and 172) where the outboard floor panels have to be removed. Refer to AMM Task 25-21-01-000-8XX-X.

(2) Remove the carpet on the LH and RH side of the cabin at the location above the center wing section (zone 171 and 172) where the outboard floor panels have to be removed. Refer to AMM Task 25-25-00-000-8XX-X.

(3) Remove floor panels 281BZ and 282CZ as indicated in figure 1 per AMM Task 53-71-01-000-8XX-X.

Refer to figure 2.

(4) Clean the center wing area at the location of the modification, including the existing drain gaps. Use:

- AR Lint-free cloth Fk05-044

- AR Methyl Ethyl Ketone (or equivalent) Fk11-003

Service Bulletin Fokker 70/100

SBF100-51-021 Apr 23/13 Page 8

Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement.

Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted except with the prior written permission of Fokker Services B.V.

B. Modification Refer to figure 2.

(1) Remove the rivet on the LH and RH side as indicated in figure 2 and enlarge the rivet holes to 7.0 (-0/+0.2) mm diameter.

(2) Treat the bare edges of both holes with conversion coating and primer. Use:

- AR Coating, conversion Alodine 1201 Fk13-003D

- AR Primer, Aerodur Aerodur S15/60 Fk07-008 Refer to figures 2, 4, 5, 6, 7 and 8.

(3) Temporarily install water drain tube pn W33021-001 on the LH side and water drain tube pn W33021-003 on the RH side. Use:

- 1 Tube, LH water drain pn W33021-001

- 1 Tube, RH water drain pn W33021-003 NOTE: If required, carefully bend the tube to ensure a stress free fit.

(4) Mark both tube ends at a distance of approximately 10 mm measured from the web plate on top of the center wing rear spar as shown in figure 6.

(5) Cut-off the tube ends on the correct length and threat the reworked edges with conversion coating. Use:

- AR Coating, conversion Alodine 1201 Fk13-003D

(6) Remove the existing bolts and washers in the clamp blocks of the hydraulic lines on the LH side in the center wing rear spar area as shown in figures 4 and 7. Discard:

- 2 Bolts pn NAS1303-10 or pn NAS1303-16 Discard

- 2 Washers pn NAS1252-10L Discard

(7) Install the water drain tube on the LH side in the center wing rear spar area with the clamps as shown in figure 4, Detail X. Refer to figure 7 for applicable mounting hardware. Use:

- 1 Tube, LH water drain pn W33021-001

- 2 Clamps pn AS21919WCE4

- 2 Bolts pn NAS6603-11 *1

- 2 Bolts pn NAS6603-17 *2

- 2 Washers pn NAS1252-10L NOTES: *1 Applicable to aircraft sn 11262 thru 11267 and 11276 thru 11441.

*2 Applicable to aircraft sn 11244 thru 11261 and 11268 thru 11275.

(8) Remove the existing bolt and washer in the clamp block of the hydraulic lines on the RH side in the center wing rear spar area as shown in figures 4 and 7. Discard:

- 1 Bolt pn NAS1303-10 or pn NAS1303-12 Discard

- 1 Washer pn NAS1252-10L Discard

Service Bulletin Fokker 70/100

Apr 23/13 SBF100-51-021 Page 9

Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement.

Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted except with the prior written permission of Fokker Services B.V.

(9) Install the water drain tube on the RH side in the center wing rear spar area with the clamps and clamping blocks as shown in figure 5, Detail X and Y. Refer to figures 7 and 8 for applicable mounting hardware for upper and lower attachment respectively.

Use:

- 1 Tube, RH water drain pn W33021-003

- 2 Clamping blocks pn A71052-077

- 2 Clamps pn AS21919WCE4

- 2 Bolts pn NAS6603-10

- 1 Bolt pn NAS6603-11 *1

- 2 Bolts pn NAS6603-11 *2

- 1 Bolt pn NAS6603-13 *1

- 7 Washers pn NAS1252-10L

- 3 Nuts pn MS21042L3 NOTES: *1 Applicable to aircraft sn 11244 thru 11261 and 11268 thru 11275.

*2 Applicable to aircraft sn 11262 thru 11267 and 11276 thru 11441.

(10) Apply sealing compound around both water drain tubes at the feed through holes in the web plates on top of the center wing rear spar as shown in figure 6. Use:

- AR Sealing compound pn PS870A Fk09-016A

(11) Close the existing drain gaps on top of the center wing torsion box with sealing compound as shown in figure 2. Use:

- AR Sealing compound pn PS870A Fk09-016A

(12) Install the water drain tube identification placards on the locations shown in figures 4 and 5, Detail B. Use:

- 2 Placards, identification pn W33022-001

(13) Apply a protective layer on the identification placards. Use:

- AR Coating, protective pn Nycote 88 Fk09-008 C. Completion of the work Refer to figure 1.

(1) Reinstall floor panels 281BZ and 282CZ as indicated in figure 1 per AMM Task 53-71-01-400-8XX-X.

(2) Reinstall the carpet on the LH and RH side of the cabin at the location above the center wing section (zone 171 and 172) where the outboard floor panels have been removed. Refer to AMM Task 25-25-00-400-8XX-X.

(3) Reinstall the passenger seats on the LH and RH side of the cabin at the location above the center wing section (zone 171 and 172) where the outboard floor panels have been removed. Refer to AMM Task 25-21-01-400-8XX-X.

Service Bulletin Fokker 70/100

SBF100-51-021 Apr 23/13 Page 10

Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement.

Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted except with the prior written permission of Fokker Services B.V.

Part 2: The Installation of Water Drain Tubes on the Center Wing Rear Spar in Aircraft with an Integral Center Wing Tank or Provisions for an Integral Center Wing Tank (Applicable to Aircraft Serial Numbers 11442 thru 11585) A. Preparation Refer to figure 1.

(1) Remove the passenger seats on the LH and RH side of the cabin at the location above the center wing section (zone 171 and 172) where the outboard floor panels have to be removed. Refer to AMM Task 25-21-01-000-8XX-X.

(2) Remove the carpet on the LH and RH side of the cabin at the location above the center wing section (zone 171 and 172) where the outboard floor panels have to be removed. Refer to AMM Task 25-25-00-000-8XX-X.

(3) Remove floor panels 281BZ and 282CZ as indicated in figure 1 per AMM Task 53-71-01-000-8XX-X.

Refer to figure 3.

(4) Clean the center wing area at the location of the modification. Use:

- AR Lint-free cloth Fk05-044

- AR Methyl Ethyl Ketone (or equivalent) Fk11-003 B. Modification Refer to figure 3.

(1) Carefully enlarge the existing drain holes to 7.0 (-0/+0.2) mm diameter on the LH and RH side as indicated in figure 3.

NOTE: Do not damage the upper side of the center wing section.

(2) Treat the bare edges of both holes with conversion coating and primer. Use:

- AR Coating, conversion Alodine 1201 Fk13-003D

- AR Primer Aerodur S15/60 Fk07-008 Refer to figures 3, 4, 5, 6, 7 and 8.

(3) Temporarily install water drain tube pn W33021-001 on the LH side and water drain tube pn W33021-003 on the RH side. Use:

- 1 Tube, LH water drain pn W33021-001

- 1 Tube, RH water drain pn W33021-003 NOTE: If required, carefully bend the tube to ensure a stress free fit.

(4) Mark the tube ends at a distance of approximately 10 mm measured from web plate on top of the center wing rear spar as shown in figure 6.

Service Bulletin Fokker 70/100

Apr 23/13 SBF100-51-021 Page 11

Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement.

Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted except with the prior written permission of Fokker Services B.V.

(5) Cut-off the tube ends on the correct length and threat the reworked edges with conversion coating. Use:

- AR Coating, conversion Alodine 1201 Fk13-003D

(6) Remove the existing bolts and washers in the clamp blocks of the hydraulic lines on the LH side in the center wing rear spar area as shown in figures 4 and 7. Discard:

- 2 Bolts pn NAS1303-10 Discard

- 2 Washers pn NAS1252-10L Discard

(7) Install the water drain tube on the LH side in the center wing rear spar area with the clamps as shown in figure 4, Detail X. Refer to figure 7 for the applicable mounting hardware. Use:

- 1 Tube, LH water drain pn W33021-001

- 2 Clamps pn AS21919WCE4

- 2 Bolts pn NAS6603-11

- 2 Washers pn NAS1252-10L

(8) Remove the existing bolt and washer in the clamp block of the hydraulic lines on the RH side in the center wing rear spar area as shown in figures 5 and 7. Discard:

- 1 Bolt pn NAS1303-10 Discard

- 1 Washer pn NAS1252-10L Discard

(9) Install the water drain tube on the RH side in the center wing rear spar area with the clamps and clamping blocks as shown in figure 5, Detail X and Y. Refer to figures 7 and 8 for applicable mounting hardware for the upper and lower attachment respectively. Use:

- 1 Tube, RH water drain pn W33021-003

- 2 Clamping blocks pn A71052-077

- 2 Clamps pn AS21919WCE4

- 2 Bolts pn NAS6603-10

- 2 Bolts pn NAS6603-11

- 7 Washers pn NAS1252-10L

- 3 Nuts pn MS21042L3

(10) Apply sealing compound around both water drain tubes at the feed through holes in the web plates on top of the center wing rear spar as shown in figure 6. Use:

- AR Sealing compound pn PS870A Fk09-016A

(11) Install the water drain tube identification placards on the positions shown in figures 4 and 5, Detail B. Use:

- 2 Placards, identification pn W33022-001

(12) Apply a protective layer on the identification placards. Use:

- AR Coating, protective pn Nycote 88 Fk09-008

Service Bulletin Fokker 70/100

SBF100-51-021 Apr 23/13 Page 12

Copyright All rights reserved by Fokker Services B.V. (The Netherlands). This document has been supplied by Fokker Services B.V . to its customers on a confidential basis subject to the provisions of an agreement.

Reproduction or disclosure to third parties of this document or any part thereof, or the use of any information contained there in for purposes other than explicitly allowed by the aforesaid agreement, is not permitted except with the prior written permission of Fokker Services B.V.

C. Completion of the work Refer to figure 1.

(1) Install floor panels 281BZ and 282CZ as indicated in figure 1 per AMM Task 53-71-01-400-8XX-X.

(2) Install the carpet on the LH and RH side of the cabin at the location above the center wing section (zone 171 and 172) where the outboard floor panels have been removed. Refer to AMM Task 25-25-00-400-8XX-X.

(3) Install the passenger seats on the LH and RH side of the cabin at the location above the center wing section (zone 171 and 172) where the outboard floor panels have been removed. Refer to AMM Task 25-21-01-400-8XX-X.

Pages 13–24 of 25