TextPartly OCR
Some pages are OCR from a scan. OCR can misread letters and numbers.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'c48cd16f5d7d564f2a91530059380c7bc614e2230ab9a42283978e3740dd3dbb' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'c48cd16f5d7d564f2a91530059380c7bc614e2230ab9a42283978e3740dd3dbb' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
CF34-8C Service Bulletins (SBs) SB 72-0356 R00 ENGINE - Compressor Stator Assembly (72-32-00) - Actuating Linkage Assembly Torque Check One-Time Inspection Date Printed:
2022/02/15 GE PROPRIETARY INFORMATION - Not to be used, disclosed to others or reproduced without the express written consent of GE. Technical data is considered ITAR and/or EAR controlled; transfer of this data to a Non-US Person, without USG authorization, is strictly prohibited.
Page 1 of 6 CF34-8C SERVICE BULLETIN - 72-0356 R00 Revised:02/15/2022 SB 72-0356 R00 ENGINE - COMPRESSOR STATOR ASSEMBLY (72-32-00) - ACTUATING
LINKAGE ASSEMBLY TORQUE CHECK ONE-TIME INSPECTION Issued:
02/15/2022 GE Designated: -CONFIDENTIAL- The information contained in this document is GE proprietary information and is disclosed in confidence. It is the property of GE and shall not be used, disclosed to others or reproduced without the express written consent of GE, including, but without limitation, it is not to be used in the creation, manufacture, development, or derivation of any repairs, modifications, spare parts, designs, or configuration changes or to obtain FAA or any other government or regulatory approval to do so. If consent is given for reproduction in whole or in part, this notice and the notice set forth on each page of this document shall appear in any such reproduction in whole or part.
This technical data is considered subject to the Export Administration Regulations (EAR) pursuant to 15 CFR Parts 730-774. Transfer of this data by any means to a Non-U.S. Person, whether in the United States or abroad, without the proper U.S.
Government authorization (e.g., License, exemption, NLR, etc.), is strictly prohibited.
Copyright (2022) General Electric Company, U.S.A.
1. PLANNING INFORMATION A. Effectivity * * * CF34-8C1/-8C5/-8C5B1 This Service Bulletin is applicable to all CF34-8C engines that have accumulated a total of 250 or more parked days outdoors (if installed on an aircraft) or stored days outdoors (if uninstalled), or any combination thereof, in the last 24 months (from the issued date of this Service Bulletin).
NOTE:The total number of parked or stored days in the last 24 months is accumulated over time and does not have to be consecutive. For example, within the last 24 months of issued date of this bulletin, if an engine installed on an aircraft was parked outdoors for 150 days, then operated for one flight, and subsequently was parked outdoors for another 100 days before returning to service, this engine would be applicable to this Service Bulletin.
NOTE:For engines not in service that are accumulating parked or stored days but have not reached the 250-day threshold at the date of this Service Bulletin release, perform this bulletin if the engine reaches the 250-day threshold before returning to service.
NOTE:Parking day is counted as 24 consecutive hours without engine operation.
NOTE:If the suspect engines have been previously inspected on-wing for freedom of movement on the actuating linkage assembly according to GE recommendations within the last 4 months of the issued date of this Service Bulletin, this Service Bulletin is not applicable.
NOTE:If the suspect engines have already been to a shop/repair facility or have had compressor cases routed to a shop/repair facility after having been through prolonged parking and the compressor case bore holes and the compressor inlet guide vane (IGV) outer shroud bushing and vane spindle bushing, were confirmed no-corrosion, the actuating linkage assembly has freedom of movement and this Service Bulletin is not applicable.
NOTE:A non-environmentally controlled facility is also applicable wherever the term "outdoors" is used.
The actuating system linkage assemblies (actuating linkage assemblies) P/N , P/N , P/N , P/N , and P/N 4128T48G03 4128T48G05 4128T48G07 4128T48G08 4128T48G09 and compressor actuating linkage assemblies (actuating linkage assemblies) P/N , P/N , and P/N are affected by this Service4129T92G01 4129T92G02 4129T92G03 Bulletin.
B. Description This Service Bulletin provides instructions to do a one-time inspection of the affected actuating linkage assembly aimed to identify possible interface corrosion/seizure on the compressor case, compressor IGV outer shroud bushing, vane spindle bushing, compressor stator IGV variable vane, compressor stator
CF34-8C Service Bulletins (SBs) SB 72-0356 R00 ENGINE - Compressor Stator Assembly (72-32-00) - Actuating Linkage Assembly Torque Check One-Time Inspection Date Printed:
2022/02/15 GE PROPRIETARY INFORMATION - Not to be used, disclosed to others or reproduced without the express written consent of GE. Technical data is considered ITAR and/or EAR controlled; transfer of this data to a Non-US Person, without USG authorization, is strictly prohibited.
Page 2 of 6 stage 1 variable vane, compressor stator stage 2 variable vane, compressor stator stage 3 variable vane, and compressor stator stage 4 variable vane.
C. Compliance NOTE:All full authority digital engine control (FADEC) CF34-8C engines with FADEC software version
6.50 and below will have inspection condition Category 1, Impact A.
NOTE:All FADEC CF34-8C engines with FADEC software version 6.60 and above will have inspection condition Category 2, Impact B.
Category 1 GE recommends that you do this Service Bulletin as soon as possible without effect on revenue service but before the date of this Service Bulletin:
(1) For engines already in service, do as follows:
(a) If the parking or storage location was less than or equal to a 10-mile (16 km) distance from a saltwater coastline, do as follows:
*On one engine per aircraft, do an inspection of the actuating linkage assembly within the next 30 flight hours or within 5 calendar days of flight operation from the issued date of this Service Bulletin, whichever comes first.
*On the sister engine, do an inspection of the actuating linkage assembly within the next 440 engine flight hours.
(b) If the parking or storage location was more than 10 miles (16 km) and less than or equal to a 50-mile (80 km) distance from a saltwater coastline, do as follows:
*On one engine per aircraft, do an inspection of the actuating linkage assembly within the next 200 flight hours or within 35 calendar days of flight operation from the issued date of this Service Bulletin, whichever comes first.
*On the sister engine, do an inspection of the actuating linkage assembly within the next 880 engine flight hours.
(c) If the parking or storage location was more than a 50-mile (80 km) distance from a saltwater coastline, do as follows:
*On one engine per aircraft, do an inspection of the actuating linkage assembly within the next 880 flight hours.
*On the sister engine, do an inspection of the actuating linkage assembly within the next 1,680 engine flight hours.
(2) For engines not in service, do as follows:
(a) Do an inspection of the actuating linkage assembly before returning to service.
Impact A This recommendation is to address a condition that may affect Flight Safety.
Category 2 GE recommends that you do this Service Bulletin as soon as possible without effect on revenue service but before the date of this Service Bulletin:
(1) For engines already in service, do as follows:
(a) If the parking or storage location was less than or equal to a 10-mile (16 km) distance from a saltwater coastline, do as follows:
*On one engine per aircraft, do an inspection of the actuating linkage assembly within the next 200 flight hours or within 35 calendar days of flight operation from the issued date of this Service Bulletin, whichever comes first.
*On the sister engine, do an inspection of the actuating linkage assembly within the next 880 engine flight hours.
(b) If the parking or storage location was more than 10 miles (16 km) and less than or equal to a 50-mile (80 km) distance from a saltwater coastline, do as follows:
*On one engine per aircraft, do an inspection of the actuating linkage assembly within the next 440 flight hours.
*On the sister engine, do an inspection of the actuating linkage assembly within the next 880 engine flight hours.
(c) If the parking or storage location was more than a 50-mile (80 km) distance from a saltwater coastline, do as follows:
*On one engine per aircraft, do an inspection of the actuating linkage assembly within the next 880 flight hours.
*On the sister engine, do an inspection of the actuating linkage assembly within the next 1,680 engine flight hours.
(2) For engines not in service, do as follows:
(a) Do an inspection of the actuating linkage assembly before returning to service.
Impact B This recommendation is to address a condition that may result in an Increased Rate of In-Flight Shutdowns (IFSD), Take-Off Aborts (TOA), Air Turn Backs (ATB) or Diversions (DIV).
NOTE:This Service Bulletin can be done on wing or in shop.
CF34-8C Service Bulletins (SBs) SB 72-0356 R00 ENGINE - Compressor Stator Assembly (72-32-00) - Actuating Linkage Assembly Torque Check One-Time Inspection Date Printed:
2022/02/15 GE PROPRIETARY INFORMATION - Not to be used, disclosed to others or reproduced without the express written consent of GE. Technical data is considered ITAR and/or EAR controlled; transfer of this data to a Non-US Person, without USG authorization, is strictly prohibited.
Page 3 of 6 This Service Bulletin is offered to improve the reliability or performance of your GE product, or to help prevent the occurrence of the event or condition described in this Service Bulletin. If the operator elects not to participate in the bulletin, that decision will be taken into consideration by GE in evaluating future product performance issues that may arise in the operator's fleet.
D. Concurrent Requirements None.
E. Reason
(1) Objective:
To improve reliability.
(2) Condition:
The actuating linkage assembly has been found to bind or stick causing engine to operate off-schedule triggering of VG CMD - POSITION DISAGREE fault. This can result in FADEC command to idle in the CF34-8C engines with software version 6.50 and below. For CF34-8C engines with FADEC software version 6.60 and above as specified in the CF34-8C S/B ,73-0045 the VG CMD - POSITION DISAGREE fault will display an ENG DEGRADED CAS message in the cockpit. This can result in an air turn-back or diversion event and under certain worst case conditions could result in a momentary compressor stall.
(3) Cause:
Corrosion has been found on the inside of the compressor case around the variable geometry stator vanes bores resulting in binding, sticking, and seizure of the compressor stator IGV variable vane, compressor stator stage 1 variable vane, compressor stator stage 2 variable vane, compressor stator stage 3 variable vane, and compressor stator stage 4 variable vane during engine operation.
(4) Inspection:
The actuating linkage assembly torque check will aid operators in the early detection of excessive corrosion build-up on the inside of the compressor case and around the compressor IGV outer shroud bushing and vane spindle bushing bores to prevent operational events.
(5) Substantiation:
Substantiation is by analysis and fleet experience.
F. Approval The data contained in this Service Bulletin has been reviewed by the FAA or authorized entity representing the FAA and the repair(s) and modification(s) herein comply with the applicable Aviation Regulations and are APPROVED for installation in the model(s) listed in this Service Bulletin.
G. Manpower After you get access to the actuating linkage assembly, you will need approximately 2 man-hours to do the inspection portion of this Service Bulletin.
H. Weight and Balance Weight and balance are not changed.
I. References (Use the latest version of these documents) Emergency Airworthiness Directive (EAD) 2021-23-51 GEK 105091-1, CF34-8C Line Maintenance Manual (LMM) GEK 105092, CF34-8C Illustrated Parts Catalog (IPC) CF34-8C S/B , ENGINE FUEL AND CONTROL - FADEC (73-21-01) - Introduction73-0045 of Improved FADEC Software Version 6.60 CF34-8C S/B , AIR SYSTEM - Compressor Variable Geometry Actuator75-0028 Components (75-30-01) - Master Compressor Variable Geometry Actuator and Slave Compressor Variable Geometry Actuator One-Time Inspection J. Publications Affected None.
K. Interchangeability Not applicable.
L. Software Accomplishment Summary Not applicable.
2. MATERIAL INFORMATION A. Material - Price and Availability
(1) Parts necessary to do this Service Bulletin:
None.
(2) Other Spare Parts:
None.
(3) Consumables:
None.
B. Industry Support Information
CF34-8C Service Bulletins (SBs) SB 72-0356 R00 ENGINE - Compressor Stator Assembly (72-32-00) - Actuating Linkage Assembly Torque Check One-Time Inspection Date Printed:
2022/02/15 GE PROPRIETARY INFORMATION - Not to be used, disclosed to others or reproduced without the express written consent of GE. Technical data is considered ITAR and/or EAR controlled; transfer of this data to a Non-US Person, without USG authorization, is strictly prohibited.
Page 4 of 6 None.
C. Configuration Chart None.
D. Parts Disposition None.
E. Tooling - Price and Availability Tool Number Description -- Torque Wrench, 110 lb in. (12.4 Nm) torque check capability
3. ACCOMPLISHMENT INSTRUCTIONS A. General
(1) For the actuating linkage assembly that connects to the master compressor variable geometry actuator (SIN 30401) and slave compressor variable geometry actuator (SIN 30402), do as follows:
(a) Disconnect the master compressor variable geometry actuator (SIN 30401) from the compressor actuator bellcranks. Refer to GEK 105091-1, 75-00-00, SPECIAL PROCEDURES 005 and do as follows:
NOTE:It is not necessary to remove or disconnect the compressor variable geometry preset link assemblies from the actuator shafts or from the compressor IGV actuating ring segment, compressor stage 1 actuating ring segment, compressor stage 2 actuating ring segment, compressor stage 3 actuating ring segment, and compressor stage 4 actuating ring segment.
1 Do an inspection of the master compressor variable geometry actuator (SIN 30401) rod-end for corrosion. Refer to GEK 105091-1, 75-00-00, SPECIAL PROCEDURES 005, Subtask 75-00-00-221-023 and do as follows:
a If you find corrosion on the master compressor variable geometry actuator (SIN 30401) rod-end, report findings to GE. Refer to Figure 1.
b If you find no corrosion and the rod end ball bearing turns freely, the master compressor variable geometry actuator (SIN 30401) rod-end is serviceable.
NOTE:If the inspection for master compressor variable geometry actuator (SIN 30401) rod-end was previously done in accordance with CF34-8C S/B or75-0028 EAD 2021-23-51 or equivalent GE recommendation, step 3.A.(1)(a) is not1 necessary, unless the engine was parked or stored outdoors or in a non-environmentally controlled facility for more than 180 days after the prior inspection was done.
(b) Disconnect the slave compressor variable geometry actuator (SIN 30402) from the compressor actuator bellcranks. Refer to GEK 105091-1, 75-00-00, SPECIAL PROCEDURES 006 and do as follows:
NOTE:It is not necessary to remove or disconnect the compressor variable geometry preset link assemblies from the actuator shafts or from the compressor IGV actuating ring segment, compressor stage 1 actuating ring segment, compressor stage 2 actuating ring segment, compressor stage 3 actuating ring segment, and compressor stage 4 actuating ring segment.
1 Do an inspection of the slave compressor variable geometry actuator (SIN 30402) rod-end for corrosion. Refer to GEK 105091-1, 75-00-00, SPECIAL PROCEDURES 006, Subtask 75-00-00-221-022 and do as follows:
a If you find corrosion on the slave compressor variable geometry actuator (SIN 30402) rod-end, report findings to GE. Refer to Figure 1.
b If you find no corrosion and the rod end ball bearing turns freely, the slave compressor variable geometry actuator (SIN 30402) rod-end is serviceable.
NOTE:If the inspection for slave compressor variable geometry actuator (SIN 30402) rod-end was previously done in accordance with CF34-8C S/B or EAD75-0028 2021-23-51 or equivalent GE recommendation, step 3.A.(1)(b) is not1 necessary, unless the engine was parked or stored outdoors or in a non-environmentally controlled facility for more than 180 days after the prior inspection was done.
CAUTION:TORQUE CHECK MUST NOT BE DONE SIMULTANEOUSLY IN THE TWO COMPRESSOR ACTUATOR BELLCRANKS. DAMAGE OF THE COMPRESSOR IGV ACTUATING RING SEGMENT, COMPRESSOR STAGE 1 ACTUATING RING SEGMENT, COMPRESSOR STAGE 2 ACTUATING RING SEGMENT, COMPRESSOR STAGE 3 ACTUATING RING SEGMENT, COMPRESSOR STAGE 4 ACTUATING RING SEGMENT, COMPRESSOR STATOR IGV ACTUATING ARM, COMPRESSOR STATOR STAGE 1 THROUGH 4 VANE ACTUATION ARM, OR COMPRESSOR STATOR SPLITLINE STAGE 1 THROUGH 4 VANE ACTUATION ARM CAN OCCUR.
(c) Install a torque wrench on the compressor actuator bellcrank forward retaining double hexagonal head machine bolt (machine bolt) where the master compressor variable geometry actuator (SIN 30401) is installed and do as follows:
1 Apply a rotational torque to move the actuating linkage assembly toward fully open and toward fully closed positions. Torque cannot be more than 110 lb in. (12.4 Nm) while you move the actuating linkage assemblies toward fully open and fully closed positions. Refer to and do as follows:Figure 2 a If you can move the actuating linkage assembly with a torque of 110 lb in.
(12.4 Nm) or less, no more action is necessary.
b If there is a compressor stator IGV actuation arm, compressor stator stage 1 through 4 vane actuation arm, or compressor stator splitline stage 1 through 4
CF34-8C Service Bulletins (SBS) SB 72-0356 ROO ENGINE - Compressor Stator Assembly (72-32-00) - Actuating Linkage Assembly Torque Check One-Time Inspection vane actuation arm stuck or if you cannot move the actuating linkage assembly toward fully open and toward fully closed positions with the recommended torque, this can be an indication of corrosion between the compressor case, compressor IGV outer shroud bushing, vane spindle bushing, compressor stator IGV variable vane, compressor stator stage 1 variable vane, compressor stator stage 2 variable vane, compressor stator stage 3 variable vane, and compressor stator stage 4 variable vane. No fly-on limits are permitted and remove the engine to clean the compressor case bore bushing holes and replace the compressor IGV outer shroud bushing and vane spindle bushing.
Send inspection report to GE. Refer to Figure 1.
(d) Connect the master compressor variable geometry actuator (SIN 30401) to the compressor actuator bellcrank. Refer to GEK 105091-1, 75-00-00, SPECIAL PROCEDURES 005.
(e) Connect the slave compressor variable geometry actuator (SIN 30402) to the compressor actuator bellcrank. Refer to GEK 105091-1, 75-00-00, SPECIAL PROCEDURES 006.
INSPECTION REPORT FOR CF34-8C S/B 72-0356 NOTE: CONTACT GE AVIATION FLEET SUPPORT IF THERE ARE ANY FINDINGS.
E-MAIL (U.S.A.): AVIATION.FLEETSUPPORT@GE.COM E-MAIL (CHINA AND ASIA): AVIATION.FLEETSUPPORT.CN@GE.COM
AIRCRAFT TAIL NUMBER
ENGINE POSITION
ENGINE SERIAL NUMBER (ESN)
ENGINE TIME SINCE NEW (ETSN)
ENGINE TIME SINCE OVERHAUL (ETSO) DATE
ENGINE MODEL
ENGINE HISTORY SEND THE INFORMATION THAT FOLLOWS: OBSERVATIONS
DO A CHECK OF THE ACTUATING LINKAGE ASSEMBLY TORQUE PASS FAIL TO 110 LB IN. (12.4 NM)
DO A CHECK OF THE MASTER COMPRESSOR VARIABLE GEOMETRY ACTUATOR PASS FAIL N/'A
ROD-END AND SLAVE COMPRESSOR VARIABLE GEOMETRY ACTUATOR ROD-END
FOR CORROSION
HAS THIS ENGINE BEEN FLYING FREQUENTLY IN BETWEEN COASTAL CITIES OR YES NO SALINE ENVIRONMENTS?
IF YES, FOR HOW LONG? (DAYS, MONTHS, OR YEARS) HAS THIS ENGINE BEEN RECENTLY STORED OUTDOORS IN A COASTAL LOCATION? _ YES NO IF YES, IN WHAT CITY WAS IT STORED?
IF YES, FOR HOW LONG? (DAYS, MONTHS, OR YEARS)
HAS THIS ENGINE BEEN INSTALLED ON A PARKED AIRCRAFT OUTDOORS IN A YES NO COASTAL LOCATION?
IF YES, FOR HOW LONG? (DAYS, MONTHS, OR YEARS) IF YES, HOW WAS THE AIRCRAFT PARKING CONDITION? (HANGAR, PARKWAY, ETC.)
IF YES, IN WHAT CITY WAS IT PARKED?
NUMBER OF ENGINE CYCLES SINCE RETURNING BACK TO NORMAL REVENUE
ENGINE OPERATION
SINCE RETURNING BACK TO NORMAL REVENUE SERVICE WHAT IS THE EXPECTED AIRCRAFT UTILIZATION GOING FORWARD (CYCLES/MONTH)?
6033627-00 Inspection Report Figure 1 GE PROPRIETARY INFORMATION - Not to be used, disclosed to others Date Printed: reproduced without the express written consent of GE. Technical data Page 2022/02/15 considered ITAR and/or EAR controlled; transfer of this data to a Non-US 5 of 6 Person, without USG authorization, is strictly prohibited.
CF34-8C Service Bulletins (SBs) SB 72-0356 ROO ENGINE - Compressor Stator Assembly (72-32-00) - Actuating Linkage Assembly Torque Check One-Time Inspection
COMPRESSOR
ACTUATOR BELLORANK
MACHINE BOLT FWD 6033983-00 Actuating Linkage Assembly Torque Check Example Figure 2 GE Designated: - CONFIDENTIAL Subject to the restrictions on the media GE PROPRIETARY INFORMATION - Not to be used, disclosed to others or Date Printed: reproduced without the express written consent of GE. Technical data Page 2022/02/15 considered ITAR and/or EAR controlled; transfer of this data to a Non-US 6 Of 6 Person, without USG authorization, is strictly prohibited.