TextPartly OCR
Some pages are OCR from a scan. OCR can misread letters and numbers.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'e6db91a065400d4dd2ac0af0188d86264f9d0d8b012b045d9fb1fdda3c336790' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'e6db91a065400d4dd2ac0af0188d86264f9d0d8b012b045d9fb1fdda3c336790' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
No of Sh:
81 Sheet No:
31 Outer combustion liner replacement disassembly Description of Working Steps:
1.52. To the labyrinth seal of the GT back shaft, assemble preparation No. 200-475-2018 to restrict turning of rotor during unlocking the nuts of the GT disc. Insert protective cover 400-476-0007 on the labyrinth.
1.53. Release progressively GT disc nuts with lockers and put them in storing plate No. 300- 745-7007 in the order they were disassembled, from 1 to 8. Loosen the nuts with adjusted wrench that can be inserted between the edge of the nut and protective cover.
Insert preparation 200-475- 2018 to the back shaft and tighten with screw.
For labyrinth protection, insert protective cover 400-476-0007 Before loosening the nuts,, protective cover must be inserted on the labyrinth.
Preparation to restrict turning of the rotor must be properly tightened.
Store the disassembled nuts in the storing plate according to the numbers (according to the position on the back shaft).
The direction of numbering of screws and nuts.
No of Sh:
81 Sheet No:
32 Outer combustion liner replacement disassembly Description of Working Steps:
1.54. Disassemble the preparation to restrict rotor turning No. 200-475-2018.
1.55. Screw on two forcing-off screws 300-475-2006/01 against each other, if possible. Apply Molyka to the screw threads. Then release and remove the back shaft of the generator. Disassemble the forcing-off screws. Store the back shaft in a protective box.
1.56.
1.57. Assemble GT disc Puller No. 100-476-2005/01. Then release and remove the GT disc and store it in a protective box to protect it from damage. Check the state of the blades for cuts and other damage (cracks, corrosion, etc.) If reassembly is to follow, store GT disc in freezer.
Using two forcing-off screws force off and remove the generator back shaft from the engine.
Protective box Protective box Preparation 100-476-2005/1 assemble to the radial compressor box flange and to the disc.
Using screws, widen the internal insert and remove the disc from the engine using other screw.
No of Sh:
81 Sheet No:
33 Outer combustion liner replacement disassembly Description of Working Steps:
1.58. Remove the GT guide vane ring with assembled inner combustion liner.
1.59. On engine versions with ecological drain container M601-227.3, a nozzle M601-206.6 that leads from the ecological container through the centrifugal compressor case and outer combustion liner must be disassembled. Without removal of this nozzle, the outer combustion liner cannot be removed.
Remove GT guide vane ring with assembled inner combustion liner with slight pulling towards yourself.
GT guide vane ring Inner combustion liner Nozzle M601-206.6 that injects unburnt fuel back to the combustion chamber.
Ecological drain container M601-
227.6 This view is not possible in the aircraft engine, ecological drain container is placed behind the front firewall.
No of Sh:
81 Sheet No:
34 Outer combustion liner replacement disassembly Description of Working Steps:
Loosen and disassemble hollow screw No. 1 along with sealing rings 10x14 CSN 02 9310.2 (Copper, 2 pieces if drain pipe is installed, or 1 piece if the drain pipe is not installed). During disassembly of hollow screw No. 1 make sure the spring M601-2516.6 does not fall out from the container and does not get lost. Then disassemble the drain pipe (if installed).
Hollow screw No. 1 Drain pipe Copper sealing rings of the hollow screw No. 1 (2 pieces) and No. 2 (2pieces).
Hollow screw No. 2 Check the nozzle for damage caused by outer liner.
Hollow screw No. 1 Hollow screw No. 2 Spring After disassembly of hollow screw No. 1 and the drain pipe, loosen the hollow screw No. 2 along with the sealing rings 24x30 CSN 02 9310.2 (Copper, 2 pieces, under and over the container). Then, remove spring M601-2516.6 from the insides of the ecological container (if it has not fallen out during disassembly of hollow screw No. 1), screen and nozzle M601-206.6.Nozzle M601-206.6
No of Sh:
81 Sheet No:
35 Outer combustion liner replacement disassembly, visual check Description of Working Steps:
1.60 Remove outer liner from the engine. Turn it to loosen it from the bayonet and pull lightly towards yourself for removal.
1.61 Cover the engine with canvas or the radial compressor box flange with plastic to prevent entrance of foreign objects or impurities in the engine. Check that all pipes and openings are sealed, including the disassembled pipes.
2 Visual check All engine parts must be carefully visually checked. Checks focus on lifespan, cracks, surface, contact surfaces, etc.
Specify any damage according to the respective maintenance manuals. Information below is indicative only.
2.1 Check of GT and PT discs: the front part of the discs may show traces of scraping and cuts to the depth of max. 0.1 mm. Brush these traces with a light sand cloth, no cuts or scraping are allowed at the area of blades hinges.
2.2 Check of GT blades: scraping of edges around the perimeter is allowed. Brush the scraping on the blade with light sand cloth. Tightened material and cuts on blades is only allowed to one third from the top of the running edges to the dept of max. 0.5 mm without sharp changes. On the other surfaces of the blades, in particular in the area of trimming edges, no damage is allowed. Damaged areas must be brushed and polished.
2.3 Deflector check: even deformed areas, if cuts create a closed circuit, reject the deflector.
Any change of defective deflector is allowed.
2.4 Other parts that must be checked, are: GT guide vane ring, PT guide vane ring, Inner combustion liner, outer combustion liner, fuel manifold deflector, deflector lock washers, diffuser vanes lock washers, straightening blades, GT bolt threads, bearings, ecologic drain canister nozzle, GT and PT blades, tightness of all threaded connections and thermocouples (measure).
No of Sh:
81 Sheet No:
36 Outer combustion liner replacement visual check Description of Working Steps:
If the tabs on the Lock Washers on the deflector are damaged or missing, remove the nut LN 5136, replace the Lock Washer LN 5333, apply Molyka to the thread, install the nut and torque to Safety the Lock Washer.
Replacement of the Lock Washers on the Diffuser Vanes:
On H-series engines: The bigger tab on the Diffuser Vanes Lock Washer M601-1092.4 must go in the hole in the diffuser, torque the nut XM601- On M601 series engines: Remove both nuts M601-1181.4 which are connected by the double Lock Washer M601-1063.4, replace the Lock Washer, apply Molyka to the thread, install both nuts Deflector Lock Washers LN 5333 6 pieces Diffuser Vanes Lock Washers:
For H-series engines M601-1092.4 For M601 series engines M60-1063.4 The bigger tab on the Lock Washer must touch the side wall of the Deflector Correct condition of the Lock Washers
No of Sh:
81 Sheet No:
37 Outer combustion liner replacement cleaning small parts Description of Working Steps:
3 Cleaning
3.1 All small parts of the PT guide vane ring (in particular flanges) with remains of sealing pastes clean with Scotch-Brite or similar. Then degrease with acetone. Brush cuts and lines.
3.2 Clean the spacers under the bearing body (if part of the engine).
Clean all PT guide vane ring flanges from sealing pastes.
Clean oil pressure pipe flanges -343.9 and oil scavenge pipe flanges -304 from sealing pastes.
Clean spacer from sealing pastes. The engine may include two washers or none.
No of Sh:
81 Sheet No:
38 Outer combustion liner replacement cleaning small parts Description of Working Steps:
3.3 If no new cover of the oil collector is needed for reassembly, clean the flanges on the cover of the oil collector from sealing pastes.
3.4 Clean the flanges of the GT guide vane ring and spacer M601-2016.4 A-E (inserted between flanges of the inner combustion liner and GT guide vane ring, if assembled).
3.5 Clean the flange on the labyrinth from sealing paste.
Thoroughly clean the GT guide vane ring flange in the area of studs.
Clean the spacer if assembled.
Clean the flanges on the cover of the oil collector and of the pressure oil and discharge oil pipes.
Clean thoroughly the labyrinth flange even between studs.
Clean the internal diameter from carbon.
No of Sh:
81 Sheet No:
39 Outer combustion liner replacement cleaning small parts Description of Working Steps:
3.6 Clean the air intake pipe flanges -880.9 and air inflate pipe flanges -828.7 from sealing pastes.
3.7 Clean the centrifugal compressor case flange and washer to be placed between the centrifugal compressor case and the exhaust case (does not have to be part of the engine).
Air intake pipe -880.9 Air inflate pipe -828.7 Clean the centrifugal compressor case flange.
Clean the spacer from both sides (if installed).
While cleaning this flange, cover the engine to prevent impurities from cleaning from entering the engine.
No of Sh:
81 Sheet No:
40 Outer combustion liner replacement assembly Description of Working Steps:
4 Assembly
4.1 Slide the outer liner to the engine and turn it to lock it in bayonet. Make sure the liner is in the correct position (marking XXX upwards, and openings opposite the torch igniter flame progagating tubes).
4.2 On engine versions with ecological drain container M601-227.3, install the nozzle M601-206.6, that goes from the ecological container through the centrifugal compressor case and outer combustion liner. Outer combustion liner must include a special opening for the nozzle.
Insert outer combustion liner to the engine, maintain the correct position XXX .
Needle that injects unburnt fuel back to the combustion chamber.
Ecological container M601-227.6 This view is not possible in the aircraft engine, ecological container is placed behind the front firewall.
No of Sh:
81 Sheet No:
41 Outer combustion liner replacement assembly Description of Working Steps Insert a sealing ring 24x30 CSN 02 9310.2 between the centrifugal compressor case and ecological drain container and then insert the nozzle M601-206.6 with screen to the container in the correct position (with the position rod in the opening on the side of the centrifugal compressor case). Then insert hollow screw No. 2 with sealing ring 24x30 CSN 02 9310.2.
Install the drain pipe (if applicable) and put the spring M601-2516.6 under the nozzle, then install the hollow bolt with sealing ring 10x14 CSN 02 9310.2 (2 sealing rings, if the drain pipe is used one sealing ring on each side of the pipe connection).
Hollow screw No. 1 Drain pipe Copper sealing rings of the hollow screw No. 1 (2 pieces) and No. 2 (2pieces.)
Hollow screw No. 2 Spring Nozzle M601-206.6
No of Sh:
81 Sheet No:
42 Outer combustion liner replacement assembly Description of Working Steps:
5 Assembly
5.1 Mount over the main shaft to the locks on the outer combustion liner the GT guide vane ring with assembled inner combustion liner. Maintain the correct mutual XXX designation always upwards.
5.2 Preheat centring opening in the main shaft for mounting (or forcing on) of the GT disc to the temperature of 90- 0 XXX disc marked with red pen. Tighten the GT disc through the 400-475-2112 to contract surface with technological nuts. Apply the mixture of molybdenum sulphide and oil (Molyka) in weight ration 2:1 to the main shaft centring before forcing on the GT disc. CAREFUL: the mixture must not contaminate the contact surface of the disc.
GT guide vane ring Inner combustion liner Insert GT guide vane ring to the locks on the outer combustion liner Centring opening in the main shaft can be preheated with heat gun.
Check the cleanness of the contact surface, apply Molyka and then heat them up.