On this page
ADs that cite it · 1
Newest first, with the revision each names, as OpenAirDocs read it from the AD’s text: check it against the AD.
Also cited in 1 proposed AD.
Text · 18OCR
This text is OCR from a scan. OCR can misread letters and numbers. © Hamilton Sundstrand Corporation. Filed by the FAA in regulations.gov docket FAA-2011-0388; AD 2011-16-03 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '091b0fe0a58ed97ab02189404eaba8eb1f83828f2ad073e099490ffcf8f2be31' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '091b0fe0a58ed97ab02189404eaba8eb1f83828f2ad073e099490ffcf8f2be31' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
Hamilton Sundstrand A United Technologies Company
SERVICE BULLETIN © 2009 Hamilton Sundstrand Corporation
PROPRIETARY
TOLD ALL SUCH INFORMATION IN CONDENCE AND ACRES RE SHALL USED ONLY FOR RECIPIENTS INTERNAL PURPOSES TO MAINTAIN RECIPENTS RECIPIENT AGREES TO
SUCH INFORMATION IN
REPAIRS MODIFICATONS SPARE PARIS DESION OF CONFIGURANTON CHANCES OR TO OBTAN PAN OR AN OCHER GSOVEANENT OR REQUATORY APPROVAL THIS DOCUMENT AND THE INFORMATION
AGREES NOT TO DISCLOSE SUCH INFORMATION TO ANY THIRD PARTY, EXCEPT AS MAY OTHERWISE BE PROVIDED FOR IN AN APPLICABLE AGREEMENT BETWEEN RECIPIENT AND HSC. COPYING OR DISCLOSURE OF THIS DOCUMENT AND THE INFORMATION CONTAINED HEREIN BY ANYONE WTHOUT HSC'S PRIOR WRITTEN PERMISSION IS NOT AUTHORIZED AND MAY RESULT IN CRIMINAL AND/OR CIVIL LIABILITY.
THE ANY TO SYSTEMS AND OR PARIS MALACTURED BY OR FOR ANATO% SUNDS AND OR PROVED BY HAMILTON SUNOSTRAND DO NOT RELY V AM WAY ON DATA IN THIS DOCUMENT TO MAINTAIN OR OTHERWISE SUPPORT SYSTEMS AND/OR PARTS THAT WERE NOT MANUFACTURED BY OR FOR HAMILTON
SUNDSTRAND OR APPROVED BY HAMILTON SUNDSTRAND WITHOUT EVIDENCE THAT THE FEDERAL AVIATION ADMINISTRATION OR OTHER HEGULATORY AGENCY
HAS DETERMINED THAT THE DATA IN THIS DOCUMENT IS VALID FOR SUCH USE Information Subject to Export Control Laws THE TECHNICAL DATA IN THIS DOCUMENT (OR FILE) IS CONTROLLED FOR EXPORT UNDER THE EXPORT ADMINISTRATION REGULATIONS (EAR), 15 CFR PARTS 730.
774, ECCN: 9E991. VIOLATIONS OF THESE LAWS MAY BE SUBJECT TO FINES AND PENALTIES UNDER THE EXPORT ADMINISTRATION ACT.
Emergency Hydraulic Power - RAT Turbine-Lower Gearbox Assembly - Replace Balance Washer Screws
1. Planning Information A. Effectivity The Hamilton Sundstrand Ram Air Turbine (RAT) Turbine-Lower Gearbox Assemblies, Model ERPS06G, that are listed below and used on the Airbus A330 and A340 aircraft are affected by this service bulletin:
Part Number Series Serial Numbers 766542 0028, 0101, 0102, 0103, 0153, 0212, 0219, 0253, 0426, 0442, 0506, 0541, 0551, 0630, 0647, 0740, 0744, 0763, 0765, 0819, 0854, 0864, 0885, 0912, 0913, 0914, 0915, 0916, 0917, 0918, 0919, 0920, 0921, 0922, 0923, 0924, 0926, 0927, 0928, 0929, 0930, 0931, 0932, 0933, 0934, 0935, 0936, 0937, 0938, 0939, 0940, 0941, 0942, 0943, 0944, 0945, 0946, 0947, 0948, 0949, 0950, 0951, 0952, 0953, 0954, 0955, 0956, 0957, 0958, 0959, 0960, 0961, 0962, 0964, 0965, 0967, 0969, 0970, 0971, 0972, 0973, 0974, 0975, 0977, 0978, 0979, 0980, 0981, 0982, 0984, 0985, 0986, 0987, 0988, 0989, 0991, 0992, 0993, 0994, 0995, 0996, 0997, 0998, 0999, 1000, 1001, 1002, 1003, 1005, 1006, 1007, 1009, 1015, 1018, 1019, 1020, 1024, 1025, 1026, 1031, 1034, 1035 1701401 0010, 0016, 0107, 0139, 0172, 0174, 0194, 0205, 0244, 0245, 0267, 0268, 0272, 0278, 0300, 0311, 0317, 0324, 0332, 0344, 0346, 0354, 0356, 0362, 0386, 0400 For information only: Records indicate the following Hamilton Sundstrand Ram Air Turbine (RAT) Modules, Model ERPS06M, were delivered with affected RAT turbine-lower gearbox assemblies from the list above:
NOTE: Not all turbine-lower gearbox assembly serial numbers can be allocated to a RAT module serial number. Therefore, the following list of RAT modules is not exhaustive.
NOTE: The following list of RAT modules is given for information only, because the subject turbinelower gearbox assemblies may have been installed on another RAT module by the operator.
Jul 20/09 ERPS06G-29-6 Page 1 of 18
HAMILTON SUNDSTRAND
SERVICE BULLETIN Part Number Series Serial Numbers 766351 0164 768084 0010, 0017, 102, 0167, 0172, 0219, 0233, 0242, 0256, 0257, 0259, 0265, 0268, 0277, 0297, 0303, 0317, 0330, 0348, 0350 770379 0156, 0410, 0426, 0490 770952 0525, 0535 1702934 0613, 0719, 0723, 0742, 0744, 0797, 0832, 0842, 0863, 0892, 0893, 0894, 0895, 0896, 0897, 0898, 0899, 0900, 0901, 0903, 0904, 0905, 0906, 0907, 0908, 0909, 0910, 0911, 0912, 0913, 0914, 0915, 0916, 0917, 0918, 0919, 0920, 0921, 0922, 0923, 0924, 0925 0926, 0927, 0928, 0929, 0930, 0931, 0932, 0933, 0934, 0935, 0936, 0937, 0938, 0939, 0941, 0942, 0944, 0946, 0947, 0948, 0949, 0950, 0951, 0952, 0954, 0955, 0956, 0957, 0958, 0959, 0961, 0962, 0963, 0964, 0965, 0966, 0968, 0969, 0970, 0971, 0972, 0973, 0974, 0975, 0976, 0977, 0978, 0979, 0981, 0982, 0983, 0985, 0994, 0999, 1000, 1001, B. Concurrent Requirements None.
C. Reason Hamilton Sundstrand has discovered that RATs were manufactured with nonconforming screws. To date, there have been five instances of a fractured balance washer screw on multiple RAT/turbinelower gearbox assembly part number configurations. Fracture of a balance washer screw can result in the loss of the associated balance washer and create an unacceptable turbine imbalance. Inspection of other screws in Hamilton Sundstrand stock revealed metallographic nonconformities consistent with those of the fractured screws. The suspect screws have been isolated to a lot from a specific supplier. Analysis indicates the nonconformance could be a result of the supplier's heat treat process, which increases susceptibility to brittle fracture. Replacement of the suspect screws with confirmed conforming screws will eliminate potential loss of a balance washer. Incorporation of this bulletin will ensure that the turbine-lower gearbox assembly balance washer screws conform to specification.
D. Description This bulletin gives instructions to replace the balance washer screws and identify the turbine-lower gearbox assembly.
For a turbine-lower gearbox assembly with a missing balance washer, or with a balance washer screw that cannot be removed in its entirety, instructions are also given to disassemble the turbinelower gearbox assembly as necessary to remove the fractured screw and balance washer, balance the turbine assembly, assemble the turbine-lower gearbox assembly, and test the turbine-lower gearbox assembly.
Jul 20/09 ERPS06G-29-6 Page 2 Use or disclosure of this data is subject to restrictions on the front page of this document.
HAMILTON SUNDSTRAND
SERVICE BULLETIN E. Compliance Incorporation of this service bulletin is to be accomplished at the earliest opportunity.
F. Approval This service bulletin contains no modification information that revises the approved configuration and therefore does not require Federal Aviation Administration (FAA) or other regulatory agency approval.
G. Manpower A maximum of 0.5 man-hour will be required to replace the balance washer screws and identify the turbine-lower gearbox assembly.
For a turbine-lower gearbox assembly with a missing balance washer, or with a balance washer screw that cannot be removed in its entirety, a maximum of 9.0 man-hours will be required to disassemble the turbine-lower gearbox assembly as necessary to remove the fractured screw and balance washer, balance the turbine assembly, assemble the turbine-lower gearbox assembly, and test the turbine-lower gearbox assembly.
H. Material - Cost and Availability
(1) Hamilton Sundstrand will supply replacement parts on a no-charge basis until July 19, 2011.
Replacement parts are currently available in limited quantities. Operators approved by Hamilton Sundstrand to perform modification of units at their facility should place a single "no charge" order to Hamilton Sundstrand. Operators can forward these orders to their assigned Hamilton Sundstrand Commercial Spares Administrator (or fax to +1-815-226-2624, if the responsible Administrator is not known). In addition, operators can also use the Hamilton Sundstrand website at www.hamiltonsundstrand.com to contact the Commercial Spares group. Upon entering the website, select "Customer Service" followed by "Commercial Spares" for other contact and order processing options that are available.
(a) The two methods for establishing order quantities based on available fleet records are listed below. In each case, Hamilton Sundstrand will acknowledge the operator order with an established delivery rate.
1 For operators who can establish a listing of affected units in their fleet through the review of records, Hamilton Sundstrand requests that a single purchase order be submitted for the total parts requirement. To minimize processing delays, orders must clearly reference the service bulletin number, serial numbers of affected units, total quantity of parts, and anticipated incorporation schedule. [To calculate the total quantity of parts to order, refer to paragraph 3. (Material Information) for the parts breakdown on a per unit basis.] If, at some point in the future, an operator finds that additional quantities of parts are required, they should contact Hamilton Sundstrand with the details so that arrangements can be made to provide them with the additional quantities.
Jul 20/09 ERPS06G-29-6 Page 3 Use or disclosure of this data is subject to restrictions on the front page of this document.
HAMILTON SUNDSTRAND
SERVICE BULLETIN For operators who cannot establish the total fleet requirements through the review of records, Hamilton Sundstrand requests that an initial purchase order be submitted to support 25 percent of their operating fleet or two aircraft, whichever is greater. This will allow an operator to have parts available on shelf in the event that an affected unit is found while performing inspections in accordance with this service bulletin. To minimize processing delays, orders must clearly reference the service bulletin number and quantity of parts. [To calculate the total quantity of parts to order, refer to paragraph 3. (Material Information) for the parts breakdown on a per unit basis.] If the initial quantity of parts provided is used and aircraft remain to be inspected, operators should contact Hamilton Sundstrand with the details so that arrangements can be made to provide additional parts.
(2) Hamilton Sundstrand will also give the following:
(a) A maximum labor allowance of 0.5 man-hour multiplied by the operator's current approved hourly rate for accomplishment of this service bulletin in the shop. The labor allowance will expire July 19, 2011.
(b) A maximum labor allowance of 0.5 man-hour multiplied by the operator's current approved hourly rate for replacement of the balance weight/washer screws on the aircraft. The labor
(c) If removal from the aircraft is required, a maximum labor allowance of 6.0 man-hours multiplied by the operator's current approved hourly rate for replacement of the RAT on the aircraft and test on wing. The labor allowance will expire July 19, 2011.
(d) Operators should forward a claim for labor reimbursement to their assigned Hamilton Sundstrand Rockford Warranty Administrator. If the responsible Administrator is not known, the claim should be mailed to Warranty Administration, 4747 Harrison Ave, Rockford, IL 61126, USA, MS 106-6. The claim should reference the service bulletin number, * serial numbers modified, date modified, total hours, and approved labor rate.
(3) For units with a missing balance weight/washer, or with a balance weight/washer screw that cannot be removed in its entirety, Hamilton Sundstrand will incorporate this modification into returned units at no charge until July 19, 2011. Contact Hamilton Sundstrand at the address that follows for scheduling information:
Hamilton Sundstrand 4747 Harrison Avenue P.O. Box 7002 Rockford, IL 61125-7002 Attention: Repair Administration Mail Stop 151-6 Telephone: +1-815-226-6849 Fax: 815-394-2414 Tooling - Price and Availability No tooling other than that required for shop maintenance of the turbine-lower gearbox assembly is required to do this modification.
Jul 20/09 ERPS06G-29-6 Page 4 Use or disclosure of this data is subject to restrictions on the front page of this document.
HAMILTON SUNDSTRAND
SERVICE BULLETIN J. Weight and Balance None.
K. Electrical Load Data Not changed.
L. References Applicable Aircraft Maintenance Manual (AMM), Hamilton Sundstrand Component Maintenance Manual (CMM) 29-21-45, and Hamilton Sundstrand Standard Practices Manual (SPM) 20-00-00.
M. Other Publications Affected Hamilton Sundstrand CMM 29-21-45 will be revised to incorporate this service bulletin.
2. Accomplishment Instructions A. General CAUTION: THE TURBINE-LOWER GEARBOX ASSEMBLY CONTAINS DESIGN CRITICAL CHARACTERISTICS, PROCESSES, AND PROCEDURES. THE DESIGN CRITICAL CHARACTERISTICS ARE IDENTIFIED WITH THE SYMBOL >>DCC<<. REFER TO THE INTRODUCTION SECTION OF CMM 29-21-45 FOR A COMPLETE EXPLANA- TION OF DESIGN CRITICAL CHARACTERISTICS.
(1) The user should obtain the material safety data sheets [Occupational Safety and Health Act (OSHA) Form 20 or equivalent] from the manufacturers or suppliers of materials to be used.
The user must become completely familiar with the manufacturer/supplier information and adhere to the procedures, recommendations, warnings, and cautions of the manufacturer/supplier for the safe use, handling, storage, and disposal of these materials. The user should also read the long version of the warnings contained in this service bulletin. The long version warnings are contained in Hamilton Sundstrand Warnings Registry 341-006 available free of charge to all organizations that are on distribution for this Service Bulletin. The Warnings Registry 341-006 is also available at www.hsvas.com.
Jul 20/09 ERPS06G-29-6 Page 5 Use or disclosure of this data is subject to restrictions on the front page of this document.
HAMILTON SUNDSTRAND
SERVICE BULLETIN B. Modification - On the Aircraft
(1) Make sure the RAT is deployed (refer to the applicable AMM).
CAUTION: THE TURBINE-LOWER GEARBOX ASSEMBLY TURBINE BLADE SHOULD BE PRO-
TECTIVELY COVERED DURING BALANCE WASHER SCREW REMOVAL AND INSTALLATION. THE BLADES CAN BE EASILY DAMAGED.
(2) Install a protective covering on the turbine-lower gearbox assembly turbine blades to prevent damage to the blades from contact with the tooling or screws.
(3) Rotate the turbine assembly and do a check for missing balance washers (refer to Figure 1 of this bulletin for the location of the balance washers).
NOTE: The number of balance washers installed will vary according to the magnitude of the imbalance that existed before the turbine assembly was balanced.
- The threaded holes around the turbine circumference (in the rear balance plane) that are not used for balance washers have a set screw installed. The set screw is secured using a 5/64-inch hex tool. The set screws should not be removed or replaced.
- The threaded holes around the turbine circumference (in the rear balance plane) with balance washers installed, use a countersunk socket head cap screw MS24667-14 to secure the washers.
- The threaded holes around the turbine circumference (in the front balance plane) each have a balance washer installed and use a countersunk socket head cap screw MS24667-14 to secure the washers.
NOTE: Missing balance washers are evidenced by the remaining screw shank and the lack of a visible hexagonal screw socket on the turbine assembly.
(4) If any balance washers are missing (because of a fractured screw), the turbine-lower gearbox assembly or RAT must be removed from the aircraft (refer to applicable AMM) for removal of the fractured screw and to balance the turbine assembly. The unit must either be returned to Hamilton Sundstrand or to a repair facility that has the capability to disassemble, repair, balance, and test the turbine-lower gearbox assembly.
CAUTION: REPLACE THE BALANCE WASHER SCREWS ONE AT A TIME. DO NOT REMOVE ALL OF THE SCREWS AT THE SAME TIME. IF MORE THAN ONE SCREW IS REMOVED AT A TIME, THE TURBINE ASSEMBLY MUST BE RE-BALANCED.
(5) If no balance washers are missing, do the steps that follow to replace the balance washer screws (one at a time):
(a) For each balance washer that is unsymmetrical in shape, use a suitable temporary marking method (tape, indelible ink, or equivalent) to mark the radial orientation of the installed balance washer. The original installed radial orientation of the washer must be maintained.
NOTE: If a balance washer is circular in shape, it is not necessary to mark its radial orientation.
Jul 20/09 ERPS06G-29-6 Page 6 Use or disclosure of this data is subject to restrictions on the front page of this document.
HAMILTON SUNDSTRAND
SERVICE BULLETIN
(b) Rotate the turbine assembly until the balance washer is positioned in a manner to minimize the potential for the balance washer to fall out (when the associated screw is removed).
CAUTION: DO NOT USE A WORN HEX TOOL WITH ROUNDED CORNERS TO REMOVE THE SCREW. IF A WORN TOOL IS USED, THE POTENTIAL EXISTS FOR STRIPPING THE SOCKET HEAD OF THE SCREW.
CAUTION: USE CARE NOT TO DAMAGE EITHER THE BALANCE WASHER OR TURBINE
ASSEMBLY IF IT IS NECESSARY TO STRIKE THE HEAD OF THE SCREW BECAUSE THE BREAK-AWAY TORQUE IS EXCESSIVE.
(c) While holding the balance washer in place, use a 3/32-inch hex tool to remove one screw from one balance washer.
NOTE: The use of a hex insert bit is preferred.
NOTE: If the screw break-away torque is excessive, it is permissible to lightly strike the head of the screw using a small hammer and a 5/16-inch (8-millimeter) pin punch.
It should not be necessary to strike more than two times.
(d) If the screw is fractured (with the balance washer installed) or if a screw fractures during removal, do the steps that follow to remove the remaining portion of the screw:
1 Report any occurrences of a fractured screw to Hamilton Sundstrand as follows:
Greg Kuczek Hamilton Sundstrand Service Engineering Phone: +1- 815-226-6581 Fax: +1-860-660-4995 E-Mail: gregory.kuczek@hs.utc.com If the remaining portion of the fractured screw is protruding above the turbine surface, do the steps that follow:
Apply protective tape on the turbine (in the area of the screw) to prevent surface damage during the removal attempt.
b Use pliers, a vice grip, or an equivalent gripping tool to remove the screw.
© Remove the protective tape from the turbine.
d If the screw is removed in its entirety, proceed to step 2.B.(5)(e) of this bulletin.
Jul 20/09 ERPS06G-29-6 Page 7 Use or disclosure of this data is subject to restrictions on the front page of this document.
HAMILTON SUNDSTRAND
SERVICE BULLETIN If the remaining portion of the screw is flush or below the turbine surface, or if the screw can not be removed in its entirety, do the steps that follow:
Hamilton Sundstrand recommends the turbine-lower gearbox assembly or RAT be removed from the aircraft (refer to the applicable AMM) for removal of the fractured screw. The unit should either be returned to Hamilton Sundstrand or to a repair facility that has the capability to disassemble, repair, balance, and test the turbine-lower gearbox assembly.
However, as an option, and at the operator's discretion, an attempt to mechanically extract a screw while the turbine-lower gearbox assembly is installed on the aircraft is allowed.
The procedure to mechanically extract a fractured screw, or one with a stripped socket head, must not use any heat or fluid. Care must be taken to make sure no filings or fragments enter the turbine assembly.
The turbine hub and turbine blades should be protectively covered to prevent mechanically induced damage during the extraction procedure.
The self-locking screw thread insert should be visually inspected (after the screw is extracted) to make sure there is no mechanical damage.
Some screws, depending on how near they are to a turbine blade, can not be extracted unless the turbine blades are disassembled from the turbine assembly. In those cases, the turbine-lower gearbox assembly or RAT must be removed from the aircraft and disassembled as necessary to remove the screw.
a Use a screw extractor (or equivalent) to remove the remaining portion of the fractured screw. Make sure no filings or fragments enter the turbine assembly. Do not use heat or fluid to remove the screw.
NOTE: If the screw can not be extracted, the turbine-lower gearbox assembly or RAT must be removed from the aircraft (refer to applicable AMM) and disassembled as necessary to remove the screw. The unit should either be returned to Hamilton Sundstrand or to a repair facility that has the capability to disassemble, repair, balance, and test the turbine-lower gearbox assembly.
b Do a visual check of the self-locking screw thread insert to make sure there is no mechanical damage.
(e) If the balance washer inadvertently falls off after the screw is removed, install the balance washer in its original installed orientation, as determined from the marking method used in
• step 2.B.(5)(a) of this bulletin.
(T) While holding the balance washer in place, install a new screw MS24667-14. Torque the screw 18 to 22 pound inches (2.1 to 2.4 Newton meters).
(g) Use a suitable temporary marking method (tape, indelible ink, or equivalent) to mark the location where the balance washer screw has been replaced.
Jul 20/09 ERPS06G-29-6 Page 8 Use or disclosure of this data is subject to restrictions on the front page of this document.
HAMILTON SUNDSTRAND
SERVICE BULLETIN
(h) Repeat steps 2.B.(5)(b) through (g) of this bulletin for each balance washer screw.
(i) Remove any tape (that was used to mark the orientation of the installed balance washers or the locations where the screws had been replaced).
1) Remove the protective covering from the turbine-lower gearbox assembly turbine blades.
(6) After all of the balance washer screws have been replaced, identify the turbine-lower gearbox assembly as follows:
(a) Engrave or vibro-etch the symbol 29-6 on a blank area of the turbine-lower gearbox identification plate (refer to Figure 1 of this bulletin for the location of the turbine-lower gearbox identification plate).
(7) Make sure the RAT is re-stowed (refer to the applicable AMM).
(8) Proceed to paragraph 2.F. of this bulletin.
Jul 20/09 ERPS06G-29-6 Page 9 Use or disclosure of this data is subject to restrictions on the front page of this document.
HAMILTON SUNDSTRAND
SERVICE BULLETIN C. Modification - In the Shop CAUTION: THE TURBINE-LOWER GEARBOX ASSEMBLY TURBINE BLADES SHOULD BE
PROTECTIVELY COVERED DURING BALANCE WASHER SCREW REMOVAL AND INSTALLATION. THE BLADES CAN BE EASILY DAMAGED.
(1) Install a protective covering on the turbine-lower gearbox assembly turbine blades to prevent damage to the blades from contact with the tooling or screws.
(2) Rotate the turbine assembly and do a check for missing balance washers (refer to Figure 1 of this bulletin for the location of the following balance washers):
- Balance washers (10, IPL Figure 2, CMM 29-21-45), (20 through -20C), and (30 through -30E).
NOTE: The number of balance washers installed will vary according to the magnitude of the imbalance that existed before the turbine assembly was balanced.
- The threaded holes around the turbine circumference (in the rear balance plane) that are not used for balance washers have a set screw installed. The set screw is secured using a 5/64-inch hex tool. The set screws should not be removed or replaced.
- The threaded holes around the turbine circumference (in the rear balance plane) with balance washers installed, use a countersunk socket head cap screw MS24667-14 to secure the washers [refer to screw (40, IPL Figure 2, CMM 29-21-45)].
- The threaded holes around the turbine circumference (in the front balance plane) each have a balance washer installed and use a countersunk socket head cap screw MS24667-14 to secure the washers [refer to screw (40, IPL Figure 2, CMM 29-21-45)].
NOTE: Missing balance washers are evidenced by the remaining screw shank and the lack of a visible hexagonal screw socket on the turbine assembly.
(3) If any balance washers are missing (because of a fractured screw), do the steps that follow:
(a) Report any occurrences of a fractured screw to Hamilton Sundstrand as follows:
Greg Kuczek Hamilton Sundstrand Service Engineering Phone: +1 - 815-226-6581 Fax: +1-860-660-4995 E-Mail: gregory.kuczek@hs.utc.com Jul 20/09 ERPS06G-29-6 Page 10 Use or disclosure of this data is subject to restrictions on the front page of this document.
HAMILTON SUNDSTRAND
SERVICE BULLETIN
(b) Disassemble the turbine-lower gearbox assembly (refer to CMM 29-21-45, DISASSEM- BLY) as necessary to remove the following parts and to get access to the fractured screw.
- Balance washers (10, IPL Figure 2, CMM 29-21-45), (20 through -20C), and (30 through -30E)
- Screws (40, IPL Figure 2, CMM 29-21-45) NOTE: Some screws, depending on how near they are to a turbine blade, can not be extracted unless the turbine blades are disassembled from the turbine assembly.
in those cases, the unit must be disassembled as necessary to remove the screw.
(c) Use a screw extractor (or equivalent) to remove the remaining portion of the fractured screw. Make sure no filings or fragments enter the turbine assembly. Do not use heat or fluid to remove the screw.
(d) Do a visual check of the self-locking screw thread insert to make sure there is no mechanical damage.
(e) Assemble the turbine assembly as necessary (refer to CMM 29-21-45, ASSEMBLY).
(f) Remove the protective covering from the turbine-lower gearbox assembly turbine blades.
(g) Balance the turbine assembly (refer to CMM 29-21-45, ASSEMBLY).
(h) Assemble the turbine-lower gearbox assembly as necessary (refer to CMM 29-21-45, ASSEMBLY).
(i) Do a test of the turbine-lower gearbox assembly (refer to CMM 29-21-45, TESTING AND FAULT ISOLATION).
() After all of the balance washer screws have been replaced, identify the turbine-lower gearbox assembly as follows (refer to SPM 20-00-00, ASSEMBLY):
1 Add the symbol 29-6 to a blank area of the identification plate (120 or -120A, IPL Figure 1, CMM 29-21-45) or (120, IPL Figure 1A).
(k) Proceed to paragraph 2.F. of this bulletin.
CAUTION: REPLACE THE BALANCE WASHER SCREWS ONE AT A TIME. DO NOT REMOVE ALL OF THE SCREWS AT THE SAME TIME. IF MORE THAN ONE SCREW IS REMOVED AT A TIME, THE TURBINE ASSEMBLY MUST BE RE-BALANCED.
(4) If no balance washers are missing, do the steps that follow to replace the balance washer screws (one at a time):
(a) For each balance washer that is unsymmetrical in shape, use a suitable temporary marking method (tape, indelible ink, or equivalent) to mark the radial orientation of the installed balance washer. The original installed radial orientation of the washer must be maintained.
NOTE If a balance washer is circular in shape, it is not necessary to mark its radial orientation.
(b) Position the unit to access the balance washer facing up.
Jul 20/09 ERPS06G-29-6 Page 11 Use or disclosure of this data is subject to restrictions on the front page of this document.
HAMILTON SUNDSTRAND
SERVICE BULLETIN CAUTION: DO NOT USE A WORN HEX TOOL WITH ROUNDED CORNERS TO REMOVE THE SCREW. IF A WORN TOOL IS USED, THE POTENTIAL EXISTS FOR STRIPPING THE SOCKET HEAD OF THE SCREW.
CAUTION: USE CARE NOT TO DAMAGE EITHER THE BALANCE WASHER OR TURBINE
ASSEMBLY IF IT IS NECESSARY TO STRIKE THE HEAD OF THE SCREW BECAUSE THE BREAK-AWAY TORQUE IS EXCESSIVE.
(c) While holding the balance washer in place, use a 3/32-inch hex tool to remove one screw from one balance washer.
NOTE: The use of a hex insert bit is preferred.
NOTE: If the screw break-away torque is excessive, it is permissible to lightly strike the head of the screw using a small hammer and a 5/16-inch (8-millimeter) pin punch.
It should not be necessary to strike more than two times.
(d) If the screw is fractured (with the balance washer installed) or if a screw fractures during removal, do the steps that follow to remove the remaining portion of the screw:
1 Report any occurrences of a fractured screw to Hamilton Sundstrand as follows:
Greg Kuczek Hamilton Sundstrand Service Engineering Phone: +1- 815-226-6581 Fax: +1-860-660-4995 E-Mail: gregory.kuczek@hs.utc.com 2 If the remaining portion of the fractured screw is protruding above the turbine surface, do the steps that follow:
a Apply protective tape on the turbine (in the area of the screw) to prevent surface damage during the removal attempt.
Use pliers, a vice grip, or an equivalent gripping tool to remove the screw.
Remove the protective tape from the turbine.
d If the screw is removed in its entirety, proceed to step 2.C.(4)(e) of this bulletin.
If the remaining portion of the screw is flush or below the turbine surface, or if the screw can not be removed in its entirety, do the steps that follow:
NOTE: The procedure to mechanically extract a fractured screw, or one with a stripped socket head, must not use any heat or fluid. Care must be taken to make sure no filings or fragments enter the turbine assembly.
The turbine hub and turbine blades should be protectively covered to prevent mechanically induced damage during the extraction procedure.
The self-locking screw thread insert should be visually inspected (after the screw is extracted) to make sure there is no mechanical damage.
Jul 20/09 ERPS06G-29-6 Page 12 Use or disclosure of this data is subject to restrictions on the front page of this document.