Copy · Leonardo Helicopters SB Emergency Alert 109-EP157 · 11 pages

© Leonardo S.p.A. Filed by the FAA in regulations.gov docket FAA-2017-0940; AD 2018-07-02 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

TextPartly OCR

Some pages are OCR from a scan. OCR can misread letters and numbers.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = 'a5a529c838e88dc0ebbde66265454d4af7c05f1aaf613c7e48a33b97ac97598e'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

N° 109EP-157 DA TE: September 8, 2017 REV. : /-March 3, 2017 Pa ge 1 of 10 TITLE ATA 62 – MAIN ROTOR BLADE TIP CAP, INSPECTION OF

REVISION LOG New Issue Leonardo S.p.A.

Via Giovanni Agusta, 520 21017 Cascina Costa di Samarate (VA) Italy Tel.: +39 0331 229111 - Fax: +39 0331 229605/222595 An appropriate entry should be made in the aircraft log book upon accomplishment.

If ownership of aircraft has changed, please, forward to new owner.

EMERGENCY ALERT

SERVICE BULLETIN

S.B. N°109EP-157 EMERGENCY ALERT DATE: September 8, 2017 Page 2 of 10 REVISION: /

1. PLANNING INFORMATION A. EFFECTIVITY All the A109EP equipped with main rotor blade P/N 709-0103-01-111 S/N 681 and S/N 683 which has accumulated less than 400FH (Time Since New).

NOTE If any of the above Main Rotor Blade is in stock, please contact aw109.mbx.aw@leonardocompany.com to obtain information on how to handle the parts.

B. COMPLIANCE Within and not later than 25 (twenty-five) flight hours since the date of issuance of this Service Bulletin and subsequently each 25 (twenty-five) flight hours.

C. CONCURRENT REQUIREMENTS N.A.

D. REASON This Service Bulletin is issued in order to provide the necessary instruction to perform a repetitive inspection of the tip cap installed on a defined batch of main rotor blades P/N 709-0103-01-111 to detect potential debonding.

E. DESCRIPTION A case of debonding of the tip cap from the main rotor blade has been reported on an AW109SP helicopter, this resulting in the loss of the tip cap in flight. This event did not compromise the conduct of flight.

The investigation has individuated as cause of the occurrence the incorrect bonding procedures during the manufacturing of some main rotor blades.

Leonardo Helicopters, as precautionary measure, issued this Service Bulletin to perform a tapping test in order to detect potential debonding and to perform the replacement of the main rotor blade.

F. APPROVAL The content of this Service Bulletin is approved under the authority of DOA nr.

EASA.21.J.005. For helicopters registered under other Aviation Authorities, before applying the Service Bulletin, applicable Aviation Authority approval must be checked within Leonardo Helicopters customer portal.

S.B. N°109EP-157 EMERGENCY ALERT DATE: September 8, 2017 REVISION: / Page 3 of 10 E.A.S.A. states mandatory compliance with inspections, modifications or technical directives and related time of compliance by means of relevant Airworthiness Directives.

If a helicopter listed in the effectivity embodies a modification or repair not LHD certified and affecting the content of this Service Bulletin, it is responsibility of the Owner/Operator to obtain a formal approval by Aviation Authority having jurisdiction on the aircraft, for any adaptation necessary before incorporation of the present Service Bulletin.

G. MANPOWER To comply with this Service Bulletin the following Maintenance-Man-Hours are deemed necessary:

approximately one (1) MMH.

Maintenance-Man-Hours are based on hands-on time and can change with personnel and facilities available.

H. WEIGHT AND BALANCE N.A.

I. REFERENCES

1) PUBLICATIONS

DATA MODULE / SECTION DESCRIPTION DM01 00-20-1 Helicopter safety DM02 62-11-17 Damage on tip cap DM03 62-11-6 Main rotor blade Removal/installation

2) ACRONYMS DOA Design Organization Approval DM Data Module EASA European Aviation Safety Agency LHD Leonardo Helicopter Division MMIR Maintenance Malfunction Information Report N.A. Not Applicable P/N Part Number SB Service Bulletin

S.B. N°109EP-157 EMERGENCY ALERT DATE: September 8, 2017 Page 4 of 10 REVISION: / S/N Serial Number

3) ANNEX Annex A Hammer Tapping Inspection AW109 Tip-Cap.

J. PUBLICATIONS AFFECTED N.A.

K. SOFTWARE ACCOMPLISHMENT SUMMARY N.A.

S.B. N°109EP-157 EMERGENCY ALERT DATE: September 8, 2017 REVISION: / Page 5 of 10

2. MATERIAL INFORMATION A. REQUIRED MATERIALS

1) PARTS P/N DESCRIPTION Q.TY NOTE 709-0103-01-111 Main rotor blade AR

2) CONSUMABLES N.A.

B. SPECIAL TOOLS P/N DESCRIPTION Q.TY NOTE PART 109-3101-58-1 or equivalent Tapping hammer (steel head) 1

C. INDUSTRY SUPPORT INFORMATION WARRANTY: Owners/Operators who comply with the instructions of this Service Bulletin no later than the applicable date in the “Compliance” section will be eligible to receive REQUIRED MATERIALS on free of charge basis, except for Consumable Materials and Special Tools.

NOTE: Customers who fail to comply with the instructions in this Service Bulletin before the compliance date are not eligible for the aforementioned special policy.

Please Issue relevant MMIR form to your Warranty Administration Dpt.

NOTE: WRM will include RETURN MATERIAL AUTHORIZATION (RMA) number; the unit disembarked (P/N 709-0103-01-111 Main Rotor Blade) from the aircraft has to be returned to LHD within thirty (30) calendar days after the shipment of the replacement part. In case of missing return within thirty (30) calendar days, Customer will be invoiced for the price of the replacement part.

NOTE: The S/N and INSPECTION REPORT are mandatory; in case the MMIR is not accompanied by these documents, it will be rejected.

S.B. N°109EP-157 EMERGENCY ALERT DATE: September 8, 2017 Page 6 of 10 REVISION: /

3. ACCOMPLISHMENT INSTRUCTIONS

1. In accordance with Maintenance Manual Section 00-20-1, prepare the helicopter on ground for a safe maintenance.

2. Gain access to the main rotor blades P/N 709-0103-01-111.

NOTE The authorized personnel who will carry out the test must comply with the requirements listed in Annex A.

3. Perform a tapping test in accordance with Annex A on the Main Rotor Blade area identified in Figure 1.

4. In case no debonding is found, proceed with step 6.

5. In case debonding is found, check its dimensions with Maintenance Manual Section 62-11-17 (debonding limits).

5.1 In case debonding is found within acceptable limits proceed with step 6.

5.2 In case debonding is found outside the acceptable limits, before next flight remove the Main Rotor Blade affected in accordance with Maintenance Manual procedures and contact Leonardo Helicopters Spa Customer Support at the following mail box:

aw109.mbx.aw@leonardocompany.com

6. Return the helicopter to a ready to flight configuration and record for compliance with this Service Bulletin on the Main Rotor Blade log card.

7. Send the attached compliance form to the following mail box:

aw109.mbx.aw@leonardocompany.com As an alternative, gain access to My Communications section on Leonardo WebPortal and compile the “Service Bulletin Application Communication”.

Page 7OCROpen in PDF

: LEONARDO

HELICOPTERS

STA STA STA 5200 5280 5630 25 mm

TIP CAP

EROSION SHIELD 115 mm

TOP SURFACE

TIF CAP 80 mm Tapping hammer area TRAILING EDGE

BOTTOM SURFACE

TIP CAP

EROSION SHIELD AREA A (Between Tip Cap and Blade body) AREA B (Between Tip Cap and Blade body) Tapping area of both upper and lower sides Figure 1 S.B. N°109EP-157 EMERGENCY ALERT DATE: September 8, 2017 REVISION: / Page 7 of 10

S.B. N°109EP-157 EMERGENCY ALERT DATE: September 8, 2017 Page 8 of 10 REVISION: /

ANNEX A HAMMER TAPPING INSPECTION AW109 TIP-CAP

ANNEX A S.B. N°109EP-157 EMERGENCY ALERT DATE: September 8, 2017 REVISION: / Page 9 of 10

SPECIFIC REQUIREMENTS OF INSPECTION Carry out hammer tapping inspection with hammer P/N 109-3101-58-1 of both upper and lower sides and nose of the blade to detect potential debonding. Report results.

GENERAL REQUIREMENTS

1. PERSONNEL AUTHORIZATION REQUIREMENTS In order to be authorized to carry out hammer tapping inspections, the assigned personnel shall:

1.1 have passed the near vision examination and colour perception requirements specified in EN4179 / NAS410;

1.2 have passed an audiometric test which consists of a test at 500, 1000, 2000 and 3000 Hz frequencies with the following acceptance criteria:

a. average maximum loss of 30 dB at the four frequencies,

b. maximum loss of 50 dB at every single frequency.

NOTE The above requirements shall be considered as a minimum; other tests and requirements based on local national health and safety protection rules are acceptable on condition that the above requirements are satisfied or exceeded.

1.3 have a minimum of 40 hours of documented practical experience obtained under the direct supervision of personnel having previous authorization in hammer tapping inspection;

1.4 have knowledge of the type of structure to be tested in order to be aware of the change of sound due to the configuration/lay-up of the part, such as, but not limited to:

 Different thickness of the top layers,  Overlap areas,  Inserts,  Changes to the geometrical form of the part,  Edge effects,  Changes to the distance between supports and fasteners,  Changes to the thickness of adhesive,  Areas with sealant,  Changes to the type of honeycomb,  Areas with core filler or splice adhesive.

ANNEX A S.B. N°109EP-157 EMERGENCY ALERT DATE: September 8, 2017 Page 10 of 10 REVISION: /

1.5 be aware of the change of sound on a specific structure when it is defective and when it is intact.

2. MAINTENANCE OF AUTHORIZATION In order to maintain the authorization to carry out hammer tapping inspections, the assigned personnel shall repeat with annual frequency the tests reported at items no.1.1 and no. 1.2 in paragraph no.1.

3. HAMMER TAPPING The hammer shall comply with the requirements of part number 109-3101-58-1 with the tapping head made of steel.

4. PROCEDURE This type of inspection is conducted by impacting the component and performing a subjective evaluation of the emitted sound.

Tapping shall be performed from a height of 25 mm to 40 mm from the surface without causing dents on the area being inspected, by moving smoothly along the direction of test and complying with the grid of 3 mm maximum.

Tap on bends and edges with the conical side (#1 in Fig. A) of the Tap hammer, while Tap on the flat areas with the rounded side of the Tap hammer (#2 in Fig. A).

Tapping shall be performed with the minimum energy necessary to generate a clear and audible sound and repeatable with the same intensity.

The inspection shall be performed in a quiet environment. The maximum level of noise (sum of the environmental noise with the noise due to the tapping inspection) should not exceed 80dB, as stated by the health protection rules. The noise level due to the tapping inspection shall be at least 5dB higher than the environmental noise without the tapping.

Figure A – Sketch of the Tapping hammer.

Remarks:

Information:

SERVICE BULLETIN COMPLIANCE FORM Date:

Number:

Revision:

Please send to the following address:

Telephone:

Fax:

B.T. Compliance Date:

Customer Name and Address:

Helicopter Model S/N Total Number Total Hours T.S.O.

LEONARDO S.p.A.

CUSTOMER SUPPORT & SERVICES - ITALY PRODUCT SUPPORT ENGINEERING & LICENSES DEPT.

Via Giovanni Agusta, 520 21017 Cascina Costa di Samarate (VA) - ITALY Tel.: +39 0331 225036 Fax: +39 0331 225988 We request your cooperation in filling this form, in order to keep out statistical data relevant to aircraft configuration up-to-date. The form should be filled in all its parts and sent to the above address or you can communicate the application also via Technical Bulletin Application Communication Section placed in Leonardo AW Customer Portal - MyCommunications Area. We thank you beforehand for the information given.