TextPartly OCR
Some pages are OCR from a scan. OCR can misread letters and numbers.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '6873d1f57b37b61b753f20898d1a35d551dc98be42070f046617de3122082834' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '6873d1f57b37b61b753f20898d1a35d551dc98be42070f046617de3122082834' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
BOLLETTINO TECNICO N° 109SP-110 The technical content of this document is approved under the authority of DOA nr. EASA.21J.005 DATE February 13, 2017 REV. / Compliance with this Bulletin is:
Page 1 of 22
SUBJECT RESCUE HOIST OPTIONAL EQUIPMENT P/N 109-B810-16-101 AND P/N 109-B810-16-201.
REASON Provide the necessary instructions to inspect and modify the actual rescue hois t installation.
HELICOPTERS AFFECTED All the AW109SP equipped with the rescue hoist kit P/N 109-B810- 16-101 and -201.
COMPLIANCE PART I^ Within and not later than 10 FH after the receipt of this Bollettino tecnico.
PART II^ Within and not later than 25 FH after the receipt of this Bollettino tecnico.
MANDATORY An appropriate entry should be made in the aircraft log book upon accomplishment.
If ownership of aircraft has changed, please, forward to new owner.
Leonardo S.p.A.
Via Giovanni Agusta, 520 21017 Cascina Costa di Samarate (VA) Italy Tel.: +39 0331 229111 - Fax: +39 0331 229605/222595 ALERT ALERT
B.T. 109SP-110 Page 2 of 22 PART III^ Before the next rescue hoist operation.
DESCRIPTION As a result of the investigation of an operational event which led to a damage of the Rescue Hoist cable, Leonardo Helicopters decided to introduce a one -time inspection of the rescue hoist handle, of the passengers’ cabin doorframe and , in case of damages, of the rescue hoist cable (PART I^), to change the attaching means of the Rescue Hoist handle on the Rescue Hoist support (PART II^) and to temporarily introduce in the Section Normal Procedure a n additional check of the rescue hoist cable to be performed before the first flight of the day (PART III^, this waiting for the full implementation of a handle and doorframe protection).
REQUIRED MANPOWER PART I^ An estimated 2 (two) manpower hours are required for compliance with this Part.
PART II^ An estimated 1 (one) manpower hours are required for compliance with this Part.
PART III^ Negligible.
WARRANTY Owners/Operators who comply with the instructions of this Bulletin, no later than the applicable date in the “Compliance section” will be eligible to receive REQUIRED MATERIALS on free of charge basis, except for Consumable Materials & Special Tools.
NOTE: Customers who fail to comply with the instructions in this bulletin before the compliance date are not eligible for the aforementioned special policy.
Please Issue relevant M.M.I.R. form ( (M)aintenance (M)alfunction (I)nformation (R)eport ) to your Warranty Administration Dpt.
B.T. 109SP-110 Page 3 of 22
NOTE: INSPECTION REPORT is mandatory; in case the MMIR is not accompanied by these documents, it will be rejected. Please destroy locally the removed parts.
REQUIRED MATERIALS The following materials are required for compliance with this Bollettino Tecnico:
PART I^: None
PART II^:
P/N DESCRIPTION Q.TY NOTE MS27039C1-13 Screw, Machine .2 Local Supply NAS1149C0332R Washer .2 Local Supply NAS1149C0316R Washer .2 Local Supply MS21042L3 Nut, self-locking .2 Local Supply (*)
(*) To get this item refer to the approved manufacturer list only (Refer to Data Module 0B-A-00-00-00-00A-947A-D within the 0B -A-IPD-00-X “Illustrated Parts Data”).
Moreover the following consumable materials, or equivalent, are necessary to accomplish this Bollettino Tecnico:
Spec./AW code number DESCRIPTION Q.TY NOTE Commercial Type 03 Cl 2 (AW code: 900004957) Loctite 242 AR Local Supply
PART III^: None
SPECIAL TOOLS N.A.
WEIGHT AND BALANCE CHANGES N.A.
B.T. 109SP-110 Page 4 of 22
REFERENCES 0B-A-AMP-00-X Maintenance Publication.
0B-B-ASRP-00-X Structural Repair Publication.
109G0040A019 AW109SP Rotorcraft Flight Manual – Optional Equipment Supplements.
109G0040A021 AW109SP Rotorcraft Flight Manual – Optional Equipment Supplements REGA.
PUBLICATIONS AFFECTED 0B-A-AMP-00-X Maintenance Publication.
0B-A-IPD-00-X Illustrated Parts Data Information.
COMPLIANCE INSTRUCTIONS
GENERAL NOTES Replace the hardware found damaged during the following operation.
PART I
1. Prepare the helicopter on ground for a safe maintenance and disconnect any power supply, in accordance with the instructions given in the 0B-A-AMP-00-X Maintenance Publication.
2. Inspect the rescue hoist handle assy (ref. Figure 1) and upper part of cabin doorframe (ref. Figure 3) for any damage caused by hoist cable (ref.
Figures 10 and 11).
2.1 If no damage is found go to step 4.
2.2 If damage is found, repair in accordance with the instructions given in the 0B-B-ASRP-00-X Structural Repair Publication.
B.T. 109SP-110 Page 5 of 22
3. Inspect the first 6 meters/20 feet of the hoist cable as follows:
WARNING The rescue hoist contains an Electrically -Initiated Explosive Device (EIED). Be careful when you do the operation test of the rescue hoist system.
– Make sure that there are no radio or rad ar transmissions in the safety distance. Refer to the local regulations for more data.
– Make sure that the electrical power to the EIED is disconnected – Keep your hands, cloths and body away from the components that are in movement.
– Always wear protective goggles and gloves when you work on the hoist.
– Only approved persons can stay near the helicopter during the operations on the rescue hoist.
If you do not obey these instructions, you can cause an explosion and possibly cause an injury to persons.
3.1 Connect an external electrical power in accordance with the instructions given in the 0B-A-AMP-00-X Maintenance Publication.
3.2 On the circuit breaker panel make sure that the circuit breakers that follow are closed:
– HOIST CONTR – HOIST PWR.
CAUTION 1:
Do not extend the hoist cable beyond the length that enables the cable hook assembly to contact the ground unless provision is made to prevent damage and entanglement of the cable.
CAUTION 2:
During the following procedures, reel cable out using care not to pull cable taut against the cable guide rollers, as kinking of the cable can result. Avoid damaging cable on rough surfaces, such as the ground.
B.T. 109SP-110 Page 6 of 22 NOTE 1:
When reeling-out the hoist cable, gently coil the cable into a 1 meter per 1 meter container (as a minimum), or equivalent, which will prevent cable contact with the ground or other abrasive surface.
3.3 Slowly rotate the control pendant REEL IN/OUT thumbwheel in the REEL OUT direction and reel-out the cable to 6 meters / 20 feet length at a controlled speed.
NOTE 2:
Cleaning the cable with a low-lint cloth will aid in the inspection requirement to locate broken wires. Broken wires will snag the cloth being used to clean the cable.
3.4 Perform cable dimension check by using a micrometre, (ref. Figure
4) measure the diameter of the rescue hoist cable as follows:
3.4.1 Measurements are to be taken at 1 meter / 3.28 feet intervals and, in addition, at any position where it is believed that necking or wear may have occurred.
3.4.2 Measure the diameter of the cable 90 degrees apart (diameter A and B).
3.4.3 Add the two measurements together and divide by 2 ( (A+B)/2 ). If, at any position the cable diameter is less than 4.70 mm / 0.185 inch replace the cable in accordance with the instructions given in the 0B-A-AMP- 00-X Maintenance Publication (Data Module 0B-B-25-91-01-08A-921A-A).
3.5 Slowly rotate the control pendant REEL IN/OUT thumbwheel in the REEL IN direction and slowly reel-in the cable at a controlled speed.
3.6 As the cable is reeling in, remove dirt from cable and visually inspect cable for broken wires, kinks, bird caging, flattened areas, abrasion, necking or other visible damage (r ef. Figures 5 to 9 for these damages examples).
3.7 Slowly reel-in the cable until the limit switches stop the hoist operation automatically and the final reel-in movement applies a tension to the hoist cable.
B.T. 109SP-110 Page 7 of 22
3.8 Release the control pendant REEL IN/OUT thumbwheel. Make sure the thumbwheel returns to the center (neutral) position automatically.
3.9 Disconnect the external power source in accordance with the instruction given in the 0B-A-AMP-00-X Maintenance Publication.
4. Return the helicopter to a ready to flight condition.
5. Fill and forward the Technical Bulletin Compliance Form to Leonardo Helicopters. To following address:
AW109 Product Support Engineering:
(AW109.mbx.aw@leonardocompany.com).
As an alternative, gain access to My Communications section on Leonardo Web Portal on AW website and compile the “Technical Bulletin Application Communication”.
6. Record compliance with PART I of this Bollettino Tecnico in the helicopter log book.
PART II
1. Prepare the helicopter on ground for a safe maintenance and disconnect any power supply, in accordance with the instructions given in the 0B-A-AMP-00-X Maintenance Publication.
2. Gain access to the handle assy of the rescue hoist.
3. In accordance with the ins tructions given in the 0B -A-AMP-00-X Maintenance Publication and Figure 1, remove (FWD zone) the nut MS21042L3, the washer P/N NAS1149C0316R, the bolt P/N AN3C6 and the washer P/N NAS1149C0332R.
B.T. 109SP-110 Page 8 of 22 NOTE 1 Apply one drop of the Adhesive (Loctite) on the threads.
NOTE 2 It is allowed to add NAS1149D0316J or NAS1149D0332J or NAS1149D0616J between the handle assy and the plate up to fill the gap between the two surfaces.
4. With reference to Figure 2, install the washer P/N NAS1149C0332R, the machine screw MS27039C1 -13 with head on outer side, the washer P/N NAS1149C0316R and the nut MS21042L3 on inner side.
4.1 Torque the nut to 2.3 – 2.8 Nm.
5. In accordance with the instructions given in the 0B -A-AMP-00-X Maintenance Publication and Figure 1, remove (AFT zone) the nut MS21042L3, the washer P/N NAS1149C0316R, the bolt P/N AN3C6 and the washer P/N NAS1149C0332R.
NOTE 3 Apply one drop of the Adhesive (Loctite) on the threads.
NOTE 4 It is allowed to add NAS1149D0316J or NAS1149D0332J or NAS1149D0616J between the handle assy and the plate up to fill the gap between the two surfaces.
6. With reference to Figure 2, install the washer P/N NAS1149C0332R, the machine screw MS27039C1 -13 with head on outer side , the washer P/N NAS1149C0316R and the nut MS21042L3 on inner side.
6.1 Torque the nut to 2.3 – 2.8 Nm.
7. Return the helicopter to a ready to flight condition.
B.T. 109SP-110 Page 9 of 22
8. Fill and forward the Technical Bulletin Comp liance Form to Leonardo Helicopters. To following address:
AW109 Product Support Engineering:
(AW109.mbx.aw@leonardocompany.com).
As an alternative, gain access to My Communications section on Leonardo Web Portal on AW website and compile the “Technical Bulletin Application Communication”.
9. Record compliance with PART II of this Bollettino Tecnico in the helicopter log book.
PART III NOTE The additional daily pre -flight check must be performed after the check at point 8 and before the check at point 9.
1. Applicable to AW109SP S/N 22203, 22213 and subs.: insert the “Normal Procedure – Additional check” page reported in Annex A of this Bollettino Tecnico at page 13 of 34 of Supplement 5 of the Docu ment 109G0040A019 AW109SP Rotorcraft Flight Manual – Optional Equipment Supplements.
Applicable to AW109SP S/N 22202, 22204 to 22212: insert the “ Normal Procedure – Additional check” page reported in Annex A of this Bollettino Tecnico at page 19 of 34 of S upplement 9.2 -5 of the Document 109G0040A021 AW109SP Rotorcraft Flight Manual – Optional Equipment Supplements REGA.
B.T. 109SP-110 Page 10 of 22
2. Fill and forward the Technical Bulletin Compliance Form to Leonardo Helicopters. To following address:
AW109 Product Support Engineering:
(AW109.mbx.aw@leonardocompany.com).
As an alternative, gain access to My Communications section on Leonardo Web Portal on AW website and compile the “Technical Bulletin Application Communication”.
Record compliance with PART III of this Bollettino Tecnico in the helicopter log book.
B.T. 109SP-110 →Q Remove -NAS1149C0332R WASHER Remove AN3C6 BOLT Remove MS21042L3 NUT Remove NAS1149C0316R WASHER 109-0717-91-113
HANDLE ASSY REF Remove Remove AN3C6 BOLT Remove MS21042L3 NUT NAS1149C0332R WASHER Remove NAS1149C0316R WASHER Figure 1 Page 11 of 22
B.T. 109SP-110 NAS1149C0316R WASHER
- MS21042L3 NUT MS27039C1-13
MACHINE SCREW NAS1149C0332R WASHER 109-0717-91-113
HANDLE ASSY REF MS21042L3 NUT MS27039C1-13 NAS1149C0316R WASHER
MACHINE SCREW NAS1149C0332R WASHER Figure 2 Page 12 of 22