Copy · U.S. DOT/FAA - Agusta BT 109-110 Rev A · 6 pages

© Leonardo S.p.A. Filed by the FAA in regulations.gov docket FAA-2008-0834; AD 2008-24-06 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

TextOCR

This text is OCR from a scan. OCR can misread letters and numbers.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = 'd9744f0bcf3757341d25d66d3f3e22181f1395d0efb5447fc4519efd3b47ed53'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Page 1OCROpen in PDF

AGUSTA Via Giovanni Agusta, 520 21017 Cascina Costa di Samarate (VA) Italy Tel.: +39 0331-229111 - Fax: +39 0331-229605/222595

AN AGUSTAWESTLAND COMPANY

TRANSLATION OF BOLLETTINO TECNICO Ne 109-110 The technical content of this document is approved DATE July 28, 1999 under the authority of DOA nr. EASA.21J.005 REV. A December 12, 2005 Compliance with MANDATORY this bulletin is:

THIS BOLLETTINO CANCELS AND SUPERSEDES THE BOLLETTINO TECNICO TELEGRAFICO N° 109-5, DATED JANUARY 27, 1987.

SUBJECT: INSPECTION FOR CRACKS OF TAIL ROTOR BLADES P/N 109-0132-02-11/-15/-121.

REASON: To emphasize the importance of performing a detailed inspection of the subject tail rotor blades for cracks, already prescribed in Bollettino tecnico telegrafico n° 109-5, dated January 27, 1987.

HELICOPTERS AFFECTED:

All Agusta helicopters A109A and A109AIl equipped with tail rotor blades P/N 109-0132-02-11/-15/-121 with 400 (four-hundred) or more flight JA hours.

NOTE Tail rotor blades P/N 109-0132-02-125 do not require compliance with this Bollettino.

COMPLIANCE:

PART I^:

Upon receipt of this Bollettino for blades having accumulated 400 (four hundred) flight hours, if the Bollettino tecnico telegrafico n° 109-5, dated January 27, 1987 has not been accomplished.

PART I|^:

Prior to the first flight of the day.

PART IIIA:

Each 100 (hundred) flight hours.

An appropriate entry should be made in the aircraft log book upon accomplishment.

If ownership of aircraft has changed, please, forward to new owner.

Page 1 of 6 A

Page 2OCROpen in PDF

B.T. 109-110 DESCRIPTION:

A second case has been reported of failure of one tail rotor blade P/N 109-0132-02, followed by the loss of tail rotor and 90° gearbox assembly.

The crack originated in the central area of the blade, in proximity of the tip of the root doubler in the chordwise sense.

The scope of this Bollettino is to prescribe a visual inspection (PART II^) and a liquid penetrant inspection (PART I^ and PART III) for presence of eventual cracks.

Subsequently new tail rotor blade P/N 109-0132-02-125 were designed and certified which have improved structural characteristics with respect to the blades P/N 109-0132-02-11/-15/-121, and do not require compliance with this Bollettino.

REQUIRED MANPOWER:

The following estimated manpower hours are necessary, for each blade, for compliance with this Bollettino :

PART I^: 1.5 manpower PART I|^: negligible PART III^: 1 manpower WARRANTY: N.A.

REQUIRED MATERIALS:

The following consumable materials are necessary to accomplish this Bollettino:

PARTI^:

SPECIFICATION NOMENCLATURE Q.TY MIL-R-25134 Ardrox 204S, solvent A.R (code 531056779) MIL-L-81352 Transparent acrylic lacquer A.R.

or MIL-PRF-81352 In addition the materials indicated in the PART III^ of this Bollettino are necessary.

PART I^:

SPECIFICATION NOMENCLATURE Q.TY TT-N-95 Aliphatic naphtha A.R.

(code 531055030) PARTE I|^:

SPECIFICATION NOMENCLATURE Q.TY TT-N-95 Aliphatic naphtha A.R.

(code 531055030) Materials to perform the liquid penetrant inspection:

• visible dye penetrant P6R available from BRENT International,

• dry developer 9D1B available from BRENT International,

• a white light source able to give an illuminance of at least 1000 lux on the area of inspection.

A Page 2 of 6

Page 3OCROpen in PDF

B.T. 109-110.

Instead of the indicated penetrant and developer, other products can be used providing that:

• they comply with the requirements of AMS 2644 (type 2 and method "C" for the penetrant and form "e" for the developer),

• they are listed in the pertinent QPL-AMS-2644-1,

• they are (penetrant and dry developer) produced by the same company.

SPECIAL TOOLS: N.A.

WEIGHT AND BALANCE CHANGES: N.A.

REFERENCES:

Maintenance Manual.

PUBLICATIONS AFFECTED:

Maintenance Manual.

Flight Manual.

COMPLIANCE INSTRUCTIONS:

NOTE The procedure reported below is applicable to each one of the two tail rotor blades, if affected by this Bollettino.

PART I^:

1. Identify and outline with adhesive tape the inspection area in accordance with figure 1 (blade upper and lower sides).

2. Using solvent Ardrox 204S or equivalent (MIL-R-25134), remove the finish paint in the above area without removing the primer underneath.

To remove the transparent paint, use solvent abundantly, in order to completely remove all paint residue.

CAUTION 1 Paint removal procedure is of the utmost importance. Failure to thoroughly remove all paint may lead to the occlusion of cracks.

CAUTION 2 Use of methylethylketone iS not recommended as damage to the bonding agent may occur.

Do not use abrasive materials to remove the paint to avoid damaging the areas of the blade. In case of presence of damage refer to the Maintenance Manual.

Page 3 of 6 A

Page 4OCROpen in PDF

B.T. 109-110

3. Perform the liquid penetrant inspection as follows:

CAUTION Personnel conducting the liquid penetrant inspection for this specification must be qualified in accordance with the ASNT practice SNT-TC-1A or other equivalent practice or standard.

The inspection shall comply with the requirements of ASTM E 1417. The blade, penetrant and ambient temperatures shall be in the range from 4 to 45 °C.

3.1. On the area of paint removal apply the penetrant for 30 to 40 minutes of dwell time.

NOTE Remove the excess of penetrant with a cheesecloth soaked with aliphatic naphtha or equivalent. The solvent shall not be poured directly on the inspection area.

Apply a uniform and thin layer of developer by means of a powder bellows; after 10 to 15 minutes of developer time, illuminate the area at 1000 lux minimum and carefully inspect it.

If presence cracks is detected, the blade must be removed from service. In this case, please inform Agusta immediately.

The potential crack would be shown running in a straight line, exactly parallel to the blade chord; it does not therefore follow the contour of the doubler and it is clearly different from evidence of bonding agent porosity that may appear along the edge of the doubler.

Upon completion of the inspection, if no cracks are found, clean he stripped areas with aliphatic naphtha, and protect with ransparent acrylic lacquer in accordance with the Maintenance Return the helicopter in ready to flight condition.

PART I^:

Use a cheesecloth soaked with aliphatic naphtha or equivalent to clean the protected area with transparent lacquer of the tail rotor blade (ref. figure 1).

A Page 4 of 6

Page 5OCROpen in PDF

B.T. 109-110

2. Perform a visual inspection on blade upper and lower sides for cracks, if necessary use a 3 to 5 power magnifying glass.

If presence of cracks is suspected perform the PART III^ of this Bollettino.

CAUTION In case of presence of other damage (nicks, dents, corrosion, etc.) on the metal refer to Maintenance Manual.

PART III^:

1. Using solvent Ardrox 204S or equivalent (MIL-R-25134), remove the transparent lacquer in the identified area shown in figure 1 (blade upper and lower sides), without removing the primer underneath.

To remove the transparent lacquer use solvent abundantly, in order to completely remove all paint residue.

CAUTION 1 Paint removal procedure is of the utmost importance. Failure to thoroughly remove all paint may lead to the occlusion of cracks.

CAUTION 2 Use of methylethylketone not recommended as damage to the bonding agent may occur.

Do not use abrasive materials to remove the paint to avoid damaging the areas of the blade. In case of presence of damage refer to the Maintenance Manual.

Perform the liquid penetrant inspection in accordance with paragraph 3. of PART I^ of this Bollettino.

If presence of cracks is detected, the blade must be removed from service. In this case, please inform Agusta immediately.

Page 5 of 6 A

Page 6OCROpen in PDF

Page 6 of 6 B.T. 109-110 Center of the blade retention bolt hole 100 mm 190 mm - 220 mm - Inspection area (upper and lower sides) FIGURE 1