Copy · Leonardo Helicopters ASB 109-158 · 25 pages

© Leonardo S.p.A. Filed by the FAA in regulations.gov docket FAA-2023-2238, the docket of AD 2024-15-11. Not covered by OpenAirDocs’ CC0 dedication.

TextPartly OCR

Some pages are OCR from a scan. OCR can misread letters and numbers.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '27d85f4cddfd6cf6cf3f1ab217707fd11fc7932e7414315cb0b659e7799a02f7'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Pa ge 1 of 24 N° 109-158 DA TE: March 21, 2023 REV. : / - M arch 15, 2017 TITLE ATA 64 – TAIL ROTOR HOUSING AND SLIDER GROUP DISASSEMBLY AND R

EASSEMBLY

REVISION LOG First Issue An appropriate entry should be made in the aircraft log book upon accomplishment.

If ownership of aircraft has changed, please, forward to new owner.

Leonardo S.p.A.

Via Giovanni Agusta, 520 21017 Cascina Costa di Samarate (VA) Italy Tel.: +39 0331 229111 - Fax: +39 0331 229605/222595 ALERT

SERVICE BULLETIN

S.B. N°109-158 ALERT DATE: March 21, 2023 Page 2 of 24 REVISION: /

1. PLANNING INFORMATION A. EFFECTIVITY Part I:

All A109C helicopters that have performed maintenance activities requiring the disassembly of the tail rotor duplex bearing housing after the helicopter delivery.

Part II:

All A109C helicopters.

B. COMPLIANCE Part I:

Within and not later than 100 (one hundred) flight hours or 6 (six) months, whichever occurs first, after the issue of this Service Bulletin.

Part II:

At each assembly of the tail rotor duplex bearing housing.

C. CONCURRENT REQUIREMENTS N.A.

D. REASON This Service Bulletin is issued in order to prescribe the disassembly and reassembly of the housing and slider assembly of the tail rotor rotating controls.

E. DESCRIPTION There have been reported cases of ring-nut tighten loss, likely as a result of poor maintenance tasks accomplishment of the assembly instructions for the tail rotor housing and slider group.

In order to minimize the likelihood of occurrence of potential human errors during maintenance, LH updated the maintenance instructions in order to provide additional guidelines, including a better identification Vital Points (VP) for the assembly of the tail rotor duplex bearing support.

As such, this Service Bulletin requires (Part I) to perform the installation of the tail rotor duplex bearing housing following the IETP updated instructions and (Part II) requires to follow such updated instructions whenever the TR duplex bearing housing is assembled.

During the procedure, the operator must obey the Local Regulations applicable to the Vital Points.

S.B. N°109-158 ALERT DATE: March 21, 2023 REVISION: / Page 3 of 24 F. APPROVAL The technical content of this Service Bulletin is approved under the authority of DOA nr.

EASA.21.J.005.

EASA states mandatory compliance with inspections, modifications or technical directives and related time of compliance by means of relevant Airworthiness Directives.

G. MANPOWER To comply with this Service Bulletin, the following MMH are deemed necessary:

Part I: 8 (eight).

Part II: N.A.

MMH are based on hands-on time and can change with personnel and facilities available.

H. WEIGHT AND BALANCE N.A.

I. REFERENCES

1) PUBLICATIONS

SECTION/PARAGRAPH DESCRIPTION PART PAR01 00-20-1 Helicopter Safety I PAR02 64-00-12 Tail rotor hub and blades assembly – Removal/Installation I PAR03 64-30-3 Pitch change mechanism – Removal/Installation I, II

2) ACRONYMS & ABBREVIATIONS AMDI Aircraft Material Data Information MM Maintenance Manual DOA Design Organization Approval IETP Interactive Electronic Technical Publications EASA European Aviation Safety Agency LH Leonardo Helicopters PTUM Pictorial Tools Usage Manual MMH Maintenance Man Hours P/N Part Number S/N Serial Number

3) ANNEX Annex A MM Section 64-30 Rev. 5

S.B. N°109-158 ALERT DATE: March 21, 2023 Page 4 of 24 REVISION: / J. PUBLICATIONS AFFECTED N.A.

K. SOFTWARE ACCOMPLISHMENT SUMMARY N.A.

S.B. N°109-158 ALERT DATE: March 21, 2023 REVISION: / Page 5 of 24

2. MATERIAL INFORMATION A. REQUIRED MATERIALS

1) PARTS N.A.

2) CONSUMABLES Refer also to AMDI for the consumable materials required to comply with the MM Paragraphs referenced in the accomplishment instructions.

3) LOGISTIC MATRIX N.A.

B. SPECIAL TOOLS Refer to PTUM for the special tools required to comply with the MM Paragraphs referenced in the accomplishment instructions.

C. INDUSTRY SUPPORT INFORMATION N.A.

S.B. N°109-158 ALERT DATE: March 21, 2023 Page 6 of 24 REVISION: /

3. ACCOMPLISHMENT INSTRUCTIONS

GENERAL NOTES

a) Place an identification tag on all components that are re-usable, including the attaching hardware that have been removed to gain access to the modification area and adequately protect them until their later re-use.

b) Shape the cables in order to prevent interference with the structure and the other existing installations, using where necessary suitable lacing cords and plastic cable tiedown.

PART I

1. In accordance with MM Paragraph 00-20-1, prepare the helicopter on ground for a safe maintenance. Disconnect the battery, all electrical power sources and/or the external power supply.

2. In accordance with MM Paragraph 64-00-12, remove from the helicopter the tail rotor hub and blades assembly.

3. In accordance with MM Paragraph 64-30-3, remove the tail rotor pitch change mechanism.

4. In accordance with MM Paragraph 64-30-3, disassemble the tail rotor housing and slider assembly.

NOTE Vital Point (VP): the point of a component, assembly or installation, where incorrect assembly or an undetected error could cause the loss of rotorcraft and/or fatalities.

5. In accordance with MM Paragraph 64-30-3 Rev. 5 (R ef. Leonardo WebPortal or Annex A of this Service Bulletin), assemble the tail rotor housing and slider assembly.

6. In accordance with MM Paragraph 64-30-3, install the tail rotor housing and slider assembly.

7. In accordance with MM Paragraph 64-00-12, install on the helicopter the tail rotor hub and blades assembly.

8. Return the helicopter to a ready to flight condition and record for compliance with Part I of this Service Bulletin on the helicopter logbook.

9. Send the attached compliance form to the following mail box:

engineering.support.lhd@leonardo.com

S.B. N°109-158 ALERT DATE: March 21, 2023 REVISION: / Page 7 of 24 As an alternative, gain access to My Communications section on Leonardo WebPortal and compile the “Service Bulletin Application Communication”.

S.B. N°109-158 ALERT DATE: March 21, 2023 Page 8 of 24 REVISION: /

PART II NOTE Vital Point (VP): the point of a component, assembly or installation, where incorrect assembly or an undetected error could cause the loss of rotorcraft and/or fatalities.

1. During the application of any maintenance operati on requiring the assembly of the TR duplex bearing housing, it is required to perform the relevant assembly procedure in accordance with MM Paragraph 64-30-3 Rev. 5 (Ref. Leonardo WebPortal or Annex A of this Service Bulletin) or later published issues.

2. Record for compliance with Part II of this Service Bulletin on the helicopter logbook.

3. Send the attached compliance form to the following mail box:

engineering.support.lhd@leonardo.com As an alternative, gain access to My Communications section on Leonardo WebPortal and compile the “Service Bulletin Application Communication”.

 Non cancellare mai questo segnalibro Non cancellare mai interruzione sezione 

ANNEX A S.B. N°109-158 ALERT DATE: March 21, 2023 REVISION: / Page 9 of 24

ANNEX A MM SECTION 64-30 REV. 5

Page 10OCROpen in PDF

LEONARDO

ANNEX A HELICOPTERS A109C-MM

- MAINTENANCE MANUAL A109C

HELICOPTER MODEL THIS 2nd ISSUE ENTIRELY SUPERSEDES ISSUE 1 DATED 26th SEPTEMBER 1994 INCLUDING REVISION 15 DATED 14" JULY 2010 Second Issue: 15th March 2013 Revision: No. 5 - 10th March 2023 THIS PUBLICATION IS ISSUED BY LEONARDO S.p.A.

This document contains proprietary data and information and shall not be disclosed, reproduced in whole or in part for any purpose, other than helicopter operation or maintenance, without prior written authorization from LEONARDO S.p.A.

PUBLICATION CODE 502052101 S.B. N°109-158 ALERT DATE: March 21, 2023 Page 10 of 24 REVISION: /

Page 11OCROpen in PDF

ANNEX A * LEONARDO HELICOPTERS A109C-MM SECTION 64-30

PITCH CHANGE MECHANISM 64-30-1. DESCRIPTION The pitch change mechanism, mounted on the 90° gearbox, consist of a sleeve sliding on the 90° output shaft, connected to the tail rotor blades by a slider and two pitch links, and to the control pedals by links and levers.

The components of the pitch change mechanism are shown in figure 64-17.

64-30-2. MAINTENANCE 64-30-3. Removal/installation (Fig 64-17) A. Input Conditions:

(1) Required conditions:

- Helicopter safe for maintenance (Chap 00).

- Access panels P6 and P12 removed (Sect 06-40).

- Tail rotor hub and blade assembly removed (Sect 64-00).

(2) Support equipment:

Tool, T/R pitch change slider ring nut removal/installation (LSE NO 9).

- Tool, T/R pitch change housing ring nut removal/installation (LSE NO 10).

- Tool, T/R pitch change housing duplex bearing removal (LSE NO 11).

- Tool, T/R pitch change housing duplex bearing installation (LSE NO 12).

- Tool, T/R pitch change slider installation (LSE NO 13).

- Tool, T/R duplex bearing removal (LSE NO 17).

- Syringe (Local supply).

- Heating gun (Local supply).

- Feeler gage (Local supply)

- Depth micrometer gage (Local supply).

- Refrigerator (Local supply).

(3) Consumable materials:

Rev. 5 641 S.B. N°109-158 ALERT DATE: March 21, 2023 REVISION: / Page 11 of 24

Page 12OCROpen in PDF

ANNEX A * LEONARDO HELICOPTERS A109C-MM WARNING: THE CONSUMABLE MATERIALS THE NOMENCLATURE OF WHICH IS PREFIXED BY "D)" ARE DANGEROUS MATERIALS. BEFORE USE, MAKE SURE TO KNOW THE SAFETY PRECAU- TIONS AND FIRST AID INSTRUCTIONS PRINTED ON:

- THE LABEL ON THE CONTAINER THE MATERIAL WAS SUPPLIED IN

- THE MATERIAL SAFETY DATA SHEET

- THE LOCAL SAFETY REGULATIONS.

ALSO MAKE SURE THAT THE APPLICABLE FIRST AID MATERIALS ARE AVAILABLE.

Abrasive paper No 300 or 400 (LCM NO 6).

(D) MEK (Methyl-ethy 1-ketone) (LCM NO 9).

(D) Retaining compound (LCM NO 19).

- (D) Grease (LCM NO 22).

- (D) Primer (LCM NO 23).

Safety wire (LCM NO 24).

(D) Lubricating oil (LCM NO 25).

(D) Adhesive (LCM NO 29).

(D) Corrosion inhibiting compound (LCM NO 40).

(D) Corrosion inhibiting compound (LCM NO 41).

(D) Primer (LCM NO 34).

Safety wire (LCM NO 36).

(D) Solvent, cleaning (LCM NO 37).

Soft lint-free cloth (Local supply).

(4) Other recommendations:

WARNING: THIS INSTALLATION INCLUDES VITAL POINTS (VP). DURING THE PROCEDURE, YOU MUST OBEY THE LOCAL REGULATIONS APPLICABLE TO THE VITAL POINTS.

CAUTION: MAKE SURE THAT YOU DO NOT MIX GREASES OF DIFFERENT BRANDS ALTHOUGH THE

SPECIFICATIONS ARE THE SAME REFER TO THE HELICOPTER LOG BOOK TO PREVENT MIXTURE OF UNWANTED GREASES.

CAUTION: THIS COMPONENT INCLUDES CRITICAL PARTS. EXAMINE THE COMPONENT FOR SIGNS OF STRUCTURAL DAMAGE, BEFORE YOU INSTALL IT ON THE HELICOPTER REFER TO SECT

20-60.

64-2 Rev. 5 S.B. N°109-158 ALERT DATE: March 21, 2023 Page 12 of 24 REVISION: /

Pages 13–24 of 25