TextPartly OCR
Some pages are OCR from a scan. OCR can misread letters and numbers.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '7a166da8e0ca3bfb0c95d8d4933b6be58aaee81a6788a17ce297cde8f825cc70' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '7a166da8e0ca3bfb0c95d8d4933b6be58aaee81a6788a17ce297cde8f825cc70' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
BOLLETTINO TECNICO N° 139-465 The technical content of this document is approved under the authority of DOA nr. EASA.21J.005 DATE December 23, 2016 REV. A - January 25, 2017 Compliance with this Bulletin is:
Page 1 of 36 S UBJECT
TAIL ROTOR DRIVE SHAFT (TRDS) INTERFERENCE REASON To perform visual inspections of the number 1 drive shaft P/N 3G6510A01132 for evidence of scratches or indentations and to provide the necessary instructions to modify the rear exhaust module P/N 3G7810A00431 and the tunnel assy P/N 3G7130A13431 by means of the rear firewalls module retro modification P/N 3G7806P06412.
HELICOPTERS AFFECTED AW139 helicopters S/Ns 31499, 31504, 31507, 31509, 31512, 31518, 31519, 31524, 31529, 31533, 31535, 31536, 31537, 31538, 31539, 31540, 31541, 31542, 31543, 31544, 31545, 31546, 31547, 31548, 31549, 31550, 31551, 31552, 31553, 31554, 31555, 31556, 31557, 31558, 31559, 31560, 31561, 31562, 31563, 31564, 31567, 31569, 31570, 31589, 41363, 41368, 41369, 41370, 41372, 41373, 41374, 41375, 41378, 41381 and 41384.
MANDATORY An appropriate entry should be made in the aircraft log book upon accomplishment.
If ownership of aircraft has changed, please, forward to new owner.
Leonardo S.p.A.
Via Giovanni Agusta, 520 21017 Cascina Costa di Samarate (VA) Italy Tel.: +39 0331 229111 - Fax: +39 0331 229605/222595
B.T. 139-465 Rev. A Page 2 of 36
COMPLIANCE Part I:
Within thirty (30) flight hours since receipt of th is Bollettino Tecnico and then every one hundred (100) flight hours until accomplishment of Part II.
Part II:
Within three hundred (300) flight hours since receipt of this Bollettino Tecnico.
DESCRIPTION Few cases of number 1 drive shaft P/N 3G6510A01132 with evidence of scratches on external surface have been reported on AW139 helicopters.
The investigations performed have demonstrated that , for AW139 helicopters equipped with rear exhaust module P/N 3G7810A00431, tunnel assy P/N 3G7130A13431 and number 1 drive shaft P/N 3G651 0A01132, manufacturing and installation tolerances could not be sufficient to ensure the necessary clearance between the parts.
Part I of this Bollettino provides the necessary in structions to perform visual inspections of the number 1 drive shaft P/N 3G6510A 01132 and, depending on findings, the replacement with a serviceable one.
Part II of this Bollettino provides the necessary i nstructions to perform the retro modification of the rear exhaust module and of the tunnel assembly in order to increase the clearance between them and the tail rotor shaft.
Present Revision A is issued to improve and clarify the instructions for reworking of the defective area including a better identificatio n of the zones of the shaft that should be protected during the rework (ref. to step 7.3 of Part I).
REQUIRED MANPOWER To comply with this Bollettino Tecnico the following Maintenance-Man-Hours (MMH) are deemed necessary:
Part I: approximately six (6) MMH.
Part II: approximately twenty (20) MMH.
Maintenance-Man-Hours are based on hands-on time an d can change with personnel and facilities available.
B.T. 139-465 Rev. A Page 3 of 36
WARRANTY Owners/Operators who comply with the instructions of this Bulletin, no later than the applicable date in the “Compliance section”, will b e eligible to receive REQUIRED MATERIALS on free of charge basis, except for Consu mable Materials & Special Tools.
NOTE: Customers who fail to comply with the instruc tions of this Bulletin before the compliance date are not eligible for the aforementioned special policy.
Please issue relevant M.M.I.R. form ( (M)aintenance (M)alfunction (I)nformation (R)eport ) to your Warranty Administration Dpt.
REQUIRED MATERIALS The following materials are required for compliance with this Bollettino Tecnico:
PART I The following consumable materials, or equivalent, are necessary to accomplish Part I of this Bollettino Tecnico:
Spec./AW code number DESCRIPTION Q.TY NOTE TT-N-95-B / Code No.
531055030 Aliphatic Naphtha (C059) AR Local Supply Type No 670 Masking Tape (C077) AR Local Supply Scotch-Brite Abrasive pad (C015) AR Local Supply
(1) Commercial Protective gloves AR Local Supply
PART II P/N DESCRIPTION Q.TY NOTE 3G7806P06412 REAR FIREWALLS RETRO
MODIFICATION REF Composed of:
3G7810P01331 REAR EXHAUST MODULE RETRO MODIFICATION REF (2) Composed of:
3G7810A08951 Skin local enlarge cover rear LH ..1 3G7810A09051 Skin local enlarge cover rear RH ..1
B.T. 139-465 Rev. A Page 4 of 36 3G7810P01551 Stiffener LH reworked ..1 3G7810P01651 Stiffener RH reworked ..1 3G7810P01451 Plate ..4 3G7106P10031 TUNNEL ASSY RETROMOD REF Composed of:
3G7130A25951 Skin local enlarge cover front LH ..1 3G7130A26051 Skin local enlarge cover front RH ..1 3G7130A26151 Seal ..2 3G7130P00351 Reinforcement tunnel LH ..1 3G7130P00451 Reinforcement tunnel RH ..1 3G7130P00551 Reinforcement tunnel LH ..1 3G7130P00651 Reinforcement tunnel RH ..1 3G7130P00751 Reinforcement plate LH ..1 3G7130P00851 Reinforcement plate RH ..1 3G7130P00951 Reinforcement plate LH ..1 3G7130P01051 Reinforcement plate RH ..1 3G7130P01351 Reinforcement ..2 (3)
Moreover the following consumable materials, or equ ivalent, are necessary to accomplish Part II of this Bollettino Tecnico:
Spec./AW code number DESCRIPTION Q.TY NOTE 199-05-152 Type III / Code No.
999999999000013871 Adhesive RTV730 (C125) AR Local Supply MIL-S-38249 Type I / Code No. 500203980 Proseal 700 (C032) AR Local Supply MS20615-3M3 Rivet 0.3Kg Local Supply MS20615-3M4 Rivet 0.1Kg Local Supply MS20615-3M3R Rivet 28 Local Supply MS20615-4M3 Rivet 0.1Kg Local Supply NAS1200M3-3 or NAS1200-3-3 Rivet 80 or
0.1Kg Local Supply NAS1200M3-3-5 Rivet 4 Local Supply NAS1200M4-4 Rivet 0.1Kg Local Supply
B.T. 139-465 Rev. A Page 5 of 36 Spec./AW code number DESCRIPTION Q.TY NOTE NAS1200M3-4 Rivet 8 (4) Local Supply
SPECIAL TOOLS The following special tools are required for compliance with this Bollettino Tecnico:
PART I P/N DESCRIPTION Q.TY NOTE MIZ-21 SR Zetec Inc. Eddy Current instrument (or equivalent) 1 (5) Commercial Depth Gauge 1 (6) Commercial Contact Point 1 (7)
PART II N.A.
NOTES:
(1) Abrasive paper fine grain, 320 grit grade, P-C- 451 specification (C017) can be used as valid alternative.
(2) P/N 3G7810A02033KIT or P/N 3G7810P00331 can be provided as a valid alternative to rear exhaust module retro modification P/N 3G7810P01331.
(3) It is possible to obtain this part reworking th e reinforcement tunnel LH P/N 3G7130A29451 or RH P/N 3G7130A29551.
(4) P/N NAS1200-3-4 may be supplied as a valid alte rnative.
(5) Refer to Annex A for the complete list of the t ools necessary to perform the Eddy Current inspection.
(6) The Depth Gauge shall be composed by:
• dial indicator with a graduation of (at least) 0.0 1 mm (for reference only: Hoffmann P/N 434807 10)
• base, compatible with the dial indicator, with a “ V” shape that allow measurement on a cylinder with a nominal diameter of 114.3 mm (for reference only: Hoffmann P/N L40010 8402)
B.T. 139-465 Rev. A Page 6 of 36
(7) Contact point, compatible with the dial indicat or, with a conical shape with an angle of 45° and Max Head radius of 0.2mm.
(for reference only: Hoffmann p/n 434900 13)
WEIGHT AND BALANCE CHANGES Compliance with this Bollettino Tecnico has the fol lowing effects on helicopter weight and balance:
PART I N.A.
PART II WEIGHT (Kg) 0.207 ARM (mm) MOMENT (Kgmm) LONGITUDINAL BALANCE 7743 1602.8 LATERAL BALANCE -6.5 -1.35
REFERENCES AW139 Aircraft Maintenance Publication (AMP).
Annex A - 3G6510A00832 tube shaft n° 1 assy Eddy C urrent inspection.
PUBLICATION AFFECTED AW139 Illustrated Part Data (IPD).
B.T. 139-465 Rev. A Page 7 of 36
COMPLIANCE INSTRUCTIONS
GENERAL NOTES
a) Place an identification tag on all components that are re-usable, including the attaching hardware that has been removed to gain access to the modification area and adequately protect them until their later reuse.
b) Exercise extreme care during drilling operations to prevent instruments, cables and hoses damage.
c) After drilling, remove all debris and sharp edges. Apply on bare metal a light film of primer unless the hole is used for ground connection.
d) Before rivet installation in places where fasteners were just removed, in accordance with the procedures reported on ASRP check hole diameter and if necessary install oversized rivets. If necessary install rivets with different grips.
e) Protect properly all those equipments not removed from area affected by the modification during installation procedure.
f) Let adhesive cure at room temperature for at least 24 hours unless otherwise specified.
g) All lengths are in mm.
PART I
1. In accordance with AMP DM 39-A-00-20-00-00A-120A -A prepare the helicopter on ground for a safe maintenance. Disconnect the ba ttery, all electrical power sources and/or the external power supply.
B.T. 139-465 Rev. A Page 8 of 36
2. In accordance with AMP DM 39-A-06-41-00-00A-010A -A open the access door 310AL, the sliding fairing 473AL and remove the acc ess panel 471AL, 472AR, 474BL, and 480AL.
3. In accordance with AMP DM 39-C-78-10-01-00A-520A -A, remove the rear exhaust module from the helicopter.
4. With reference to Figure 1, visual inspect the t ube shaft P/N 3G6510A00832 (part of the number 1 drive shaft) for evidence of scratches or indentations in the indicated area rotating it, if necessary.
4.1. If no scratches or indentations are detected, proceed as described in step 10.
4.2. If scratches or indentations are detected, pro ceed as described in the following step 5.
5. In accordance with AMP DM 39-B-65-11-01-00A-520A -A remove the number 1 drive shaft P/N 3G6510A01132.
6. In accordance with AMP DM 39-B-65-11-04-00A-520A -A remove the number 1 flexible coupling P/N 4G6510V00151.
7. With reference to Figure 1 position the number 1 drive shaft P/N 3G6510A01132 on a workbench and perform the tub e shaft P/N 3G6510A00832 rework as described in the following procedure:
NOTE Clean and dry gloves shall be worn during cleaning and all the following operations.
7.1. With reference to Figure 1, clean and degrease the indicated area of the number 1 drive shaft P/N 3G6510A01132 by means of A liphatic Naphtha (C059).
7.2. With reference to Figure 1, adequately mask th e tube/drive shaft to prevent the ingress of rework debris in critical areas.
NOTE Machining operations are not allowed.
For limits and surface roughness refer to Figure 1.
7.3. With reference to Figure 1, smooth with wide r adius the defective area of the tube/drive shaft by means of Scotch-Brite or ab rasive paper fine grain
B.T. 139-465 Rev. A Page 9 of 36 (320 grit grade) to completely remove scratches, to break sharp edges and remove possible material swellings. Remove the less material quantity as possible. Do not exceed a maximum width of the r eworked area of
10.00 mm as indicated in Figure 1.
NOTE The maximum allowed depth of the scratch/indentation is 0.200 mm (0.079 in)
7.4. With reference to Figure 2, perform a depth ch eck of the reworked area by means of a depth gauge, taking care of setting the “zero” of the gauge out of the reworked area indicated in Figure 1.
7.5. If the measured depth of the scratch is higher than 0.200 mm (0.079 in), in accordance with AMP DM 39-B-65-11-01-00A-520A-A and DM 39-B-65-11-01-00A-720A-A, replace number 1 drive shaft P/N 3G6510A01132 and skip to Part II.
7.6. If the measured depth of the scratch is lower than 0.200 mm (0.079 in), in accordance with the Annex A, perform the Eddy Curre nt inspection on the reworked area of the tube/drive shaft.
7.7. If cracks are present, in accordance with AMP DM 39-B-65-11-01-00A-520A-A and DM 39-B-65-11-01-00 A-720A-A, replace number 1 drive shaft P/N 3G6510A01132 and s kip to Part II.
Otherwise skip to step 7.8.
7.8. Remove the masking from the tube/drive shaft.
7.9. Mark the number DTRPTCM 11210016 by means of r ubber stamp and permanent ink near the reworked area of the tube sh aft P/N 3G6510A00832 of the number 1 drive shaft P/N 3G6510A01132.
8. In accordance with AMP DM 39-B-65-11-04-00A-720A -A reinstall the number 1 flexible coupling P/N 4G6510V00151.
9. In accordance with AMP DM 39-B-65-11-01-00A-720A -A reinstall the number 1 drive shaft P/N 3G6510A01132.
10. In accordance with AMP DM 39-C-78-10-01-00A-720 A-A, install the rear exhaust module on the helicopter.
B.T. 139-465 Rev. A Page 10 of 36
11. In accordance with AMP DM 39-A-06-41-00-00A-010 A-A close the access door 310AL, the sliding fairing 473AL and reinstall the access panel 474BL.
12. In accordance with AMP DM 39-A-06-41-00-00A-010 A-A reinstall the access panel 480AL, 471AL and 472AR.
13. Return helicopter to flight configuration and r ecord for compliance with Part I of this Bollettino Tecnico on helicopter log book.
14. Send the attached compliance form to:
cse.aw139.aw@leonardocompany.com As an alternative, gain access to My Communications section on Leonardo AW Customer Portal and compile the “Technical Bulletin Application Communication”.
B.T. 139-465 Rev. A Page 11 of 36
PART II
1. In accordance with AMP DM 39-A-00-20-00-00A-120A -A prepare the helicopter on ground for a safe maintenance. Disconnect the ba ttery, all electrical power sources and/or the external power supply.
2. In accordance with AMP DM 39-A-06-41-00-00A-010A -A open the access door 310AL, the sliding fairing 473AL and remove the acc ess panel 471AL, 472AR, 474BL, and 480AL.
3. In accordance with AMP DM 39-A-71-11-03-00A-520A -A remove the top forward cowl in order to get access to the work area.
4. In accordance with AMP DM 39-C-78-10-01-00A-520A -A, remove the rear exhaust module P/N 3G7810A00431 from the helicopter.
5. In accordance with AMP DM 39-C-78-10-04-00A-520A -A and DM 39-C-78-10-06-00A-520A-A, remove the left and th e right exhaust ducts from the helicopter.
6. In accordance with AMP DM 39-C-78-10-01-01A-520A -B, remove the LH and the RH ejector assemblies from the rear exhaust module.
NOTE Skip to step 10 if Rear Firewalls Module Assy P/N 3G7810A02033KIT or P/N 3G7810P00331 has been provided.
NOTE In order to avoid any damage on the helicopter, the following reworking procedure has to be performed on working bench.
7. With reference to Figures 3 thru 6, rework rear exhaust module P/N 3G7810A00431 by means of the rear exhaust modul e retro modification P/N 3G7810P01331 as described in the following procedure:
7.1 With reference to Figure 4 View A and Figure 5 View E, temporarily put in place the stiffener for mount rear exhaust LH P/N 3 G7810P01551 and the stiffener for mount rear exhaust RH P/N 3G7810P0165 1, coordinating with existing holes on the mount rear exhaust LH P/N 3G7 810A04651 and RH P/N 3G7810A05851. Mark position of n°34 rivet holes on related mount
B.T. 139-465 Rev. A Page 12 of 36 rear exhausts.
7.2 With reference to Figure 4 View A and Detail C cut the mount rear exhaust LH P/N 3G7810A04651 and the mount rear exhaust RH P/N 3G7810A05851 coordinating with stiffener for mo unt rear exhaust LH P/N 3G7810P01551 and RH P/N 3G7810P01651.
7.3 With reference to Figure 4 Section B-B, perform a cut out on bend plate LH P/N 3G7810A04351 and RH P/N 3G7810A05551 coordin ating with skin local enlarge cover rear LH P/N 3G7810A08951 a nd RH P/N 3G7810A09051. If necessary, use Figure 11 to pe rform the cut, coordinating with mount rear exhaust existing holes.
7.4 With reference to Figure 4 Section B-B, drill o ut the indicated existing rivets.
7.5 With reference to Figure 5 View E, install stif fener for mount rear exhaust LH P/N 3G7810P01551 by means of n°6 rivets P/N MS20 615-3M3R and n°11 rivets P/N NAS1200M3-4 on mount rear LH.
7.6 With reference to Figure 5 View E, install stif fener for mount rear exhaust RH P/N 3G7810P01651 by means of n°6 rivets P/N MS20 615-3M3R and n°11 rivets P/N NAS1200M3-4 on mount rear RH.
7.7 With reference to Figure 5 View D and H and Fig ure 6 Section J-J, temporarily put in place the skin local enlarge cov er rear LH P/N 3G7810A08951 and RH P/N 3G7810A09051 and the n° 4 plates P/N 3G7810P01451. Mark position of n°26 rivet holes of the skin local enlarge covers on bend plates.
NOTE Apply sealant Proseal 700 (C032) on the mating surfaces of the skin local enlarge cover rear LH P/N 3G7810A08951 and RH P/N 3G7810A09051 and the n°4 plates P/N 3G7810P01451 before their installation (ref. step 7.8).
7.8 With reference to Figure 5 View H and Figure 6 Section J-J, install skin local enlarge cover rear LH P/N 3G7810A08951 and RH P/N 3G7810A09051 and the n°4 plates P/N 3G7810P0145 1 by means of