Text
From the PDF’s text layer: layout, tables and figures are lost. The PDF is the document.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '5d8d7c2da4565d4a80a1e82c96aaf3cbc4726df808cb5813c8edc0820e65973c' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '5d8d7c2da4565d4a80a1e82c96aaf3cbc4726df808cb5813c8edc0820e65973c' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
Page 1 of 20 N° 139-725 DATE: July 25, 2022 REV. : A - August 9, 2022 TITLE ATA 64 – TAIL ROTOR DUPLEX BEARING INSPECTION AND REPLACEMENT
REVISION LOG Revision A is issued in order to prescribe the TRA P /N 3G6730V00731 or P/N 3G6730V00732 replacement when relative rotation between the trunnion and the PCR is found.
Helicopters already compliant with the previous issue of this Service Bulletin and that have found rotation according to the inspection of section 3 “Accomplishment instructions” of the Service Bulletin Part I step 3 or Part III step 4 shall replace before next flight the TRA with a new item in accordance with section 3 “Accomplishment instructions” of the Service Bulletin Part I step 4.4 or Part III step 7.4.
Leonardo S.p.A.
Via Giovanni Agusta, 520 21017 Cascina Costa di Samarate (VA) Italy Tel.: +39 0331 229111 - Fax: +39 0331 229605/222595 An appropriate entry should be made in the aircraft log book upon accomplishment.
If ownership of aircraft has changed, please, forward to new owner.
EMERGENCY ALERT
SERVICE BULLETIN
S.B. N°139-725 EMERGENCY ALERT DATE: July 25, 2022 Page 2 of 20 REVISION: A - August 9, 2022
1. PLANNING INFORMATION A. EFFECTIVITY Part I and Part II:
All AB139/AW139 helicopters installing tail rotor duplex bearings P/N 3G6430V00151, P/N 3G6430V00152 or P/N 3G6430V00153 that have less than 2400 FH and that have been removed and reinstalled on sliding control assembly P/N 3G6430A02531.
Part III:
All AB139/AW139 helicopters installing tail rotor duplex bearings P/N 3G6430V00151, P/N 3G6430V00152 or P/N 3G6430V00153 that have logged 2400 FH or more.
Part IV:
NOTE Each letter A thru E of the list below identifies the affected components to be replaced in accordance with the compliance times, identified by the same letters in the list of the Compliance Part IV.
A. All duplex bearings P/N 3G6430V00151, P/N 3G6430V00152 or P/N 3G6430V00153 that have less than 2400 FH and that have been removed and reinstalled on sliding control assembly P/N 3G6430A02531;
B. All duplex bearings P/N 3G6430V00151, P/N 3G6430V00152 or P/N 3G6430V00153 that have less than 2400 FH and that have NOT been removed and reinstalled on sliding control assembly P/N 3G6430A02531;
C. All duplex beari ngs P/N 3G6430V00151, P/N 3G6430V00152 or P/N 3G6430V00153 that have logged 2400 FH or more;
D. All duplex bearings P/N 3G6430V00151, P/N 3G6430V00152 or P/N 3G6430V00153 kept in stock and that have been removed from a sliding control assembly P/N 3G6430A02531;
E. All duplex bearings P/N 3G6430V00151, P/N 3G6430V00152 or P/N 3G6430V00153 that have been removed and reinstalled on a sliding control assembly P/N 3G6430A02531 kept in stock.
B. COMPLIANCE Part I:
Before next flight and then every 10 FH until the bearing is replaced.
S.B. N°139-725 EMERGENCY ALERT DATE: July 25, 2022 REVISION: A - August 9, 2022 Page 3 of 20 Part II:Scegliere un elemento.
Within and not later than 10 FH after the issue of this Service Bulletin and then every 50 FH until the bearing is replaced.
Part III:
Before next flight and then every 5 FH until the bearing is replaced.
Part IV:
NOTE Each letter A thru E below is the applicable compliance time for the components identified with the same letters in the list of Effectivity Part IV.
A. Within and not later than 200 FH after the first application of Part II or before exceeding 2400 FH of the bearings whichever occurs first;
B. When the bearings reach 2400 FH;
C. Within and not later than 10 FH after the first application of Part III;
D. Before next installation;
E. Before next installation.
C. CONCURRENT REQUIREMENTS N.A.
D. REASON This Service Bulletin is issued in order to prescribe the inspection of the tail rotor duplex bearing P/N 3G6430V00151, P/N 3G6430V00152 or P/N 3G6430V00153 and its replacement when necessary.
E. DESCRIPTION Leonardo Helicopters has developed this Service Bulleti n following a reported occurrence of a tail r otor duplex bearing found damaged on an AW139. The investigation found that the bearing was removed and reinstalled on another sliding control assembly, even though AMP procedures do not allow reinstallation of a previously removed bearing.
The AW139 AMPI Chapter 5 DM 39-A-05-13-00-00A-028E-P will be revised to update the bearings Discard Time to 2400 FH.
Part I of this Service Bulletin applies to the helicopters installing tail rotor duplex bearings that have less than 2400 FH and that have been reinstalled on sliding control assembly
S.B. N°139-725 EMERGENCY ALERT DATE: July 25, 2022 Page 4 of 20 REVISION: A - August 9, 2022
P/N 3G6430A02531 during application of AMPI Chapter 5 task 64-26 (2400 FH inspection) or AMPI Chapter 5 tasks 64-23 or 64-24 (4 Years inspection) or any other reason. Part I requires to apply a slippage mark between the PCR and the trunnion installed on the back-end of the TRA and to perform repetitive inspections for absence of rotation of the parts. If the inspection fails, the bearing must be replaced immediately.
If rotation is found, also the TRA P/N 3G6730V00731 or P/N 3G6730V00732 must be replaced before next flight.
Part II of this Service Bulletin gives instructions to inspect the tail rotor duplex bearings that have less than 2400 FH and that have been reinstalled on sliding control assembly P/N 3G6430A02531 during application of AMPI Chapter 5 task 64 -26 (2400 FH inspection) or AMPI Chapter 5 tasks 64 -23 or 64-24 (4 Years inspection) or any other reason. Aim of the inspection is to check the bearings condition, absence of parti cles within bearing grease and to perform the roughness check. If any of the inspections fails, the bearing must be replaced immediately.
Part III of this Service Bulletin gives instructions to inspect the tail rotor duplex bearings that have logged 2400 FH or more, in order to check their condition and to perform an inspection for absence of rotation as described for Part I. If any of the inspections fails, the bearing must be replaced immediately. If rotation is found , also the TRA P/N 3G6730V00731 or P/N 3G6730V00732 must be replaced before next flight.
Part IV of this Service Bulletin gives instructions to replace the bearings in accordance with the applicable compliance time.
F. APPROVAL The technical content of this Service Bulletin is approved under the authority of DOA nr.
EASA.21.J.005. For helicopters registered under other Aviation Authorities, before applying the Service Bulletin, applicable Aviation Authority approval must be checked within Leonardo Helicopters customer portal.
EASA states manda tory compliance with inspections, modifications or technical directives and related time of compliance by means of relevant Airworthiness Directives.
If an aircraft listed in the effectivity embodies a modification or repair not LHD certified and affecting the content of this Service Bulletin, it is responsibility of the Owner/Operator to obtain a formal approval by Aviation Authority having jurisdiction on the aircraft, for any adaptation necessary before incorporation of the present Service Bulletin.
S.B. N°139-725 EMERGENCY ALERT DATE: July 25, 2022 REVISION: A - August 9, 2022 Page 5 of 20 G. MANPOWER To comply with this Service Bulletin the following MMH are deemed necessary:
Part I: approximately half (0,5) MMH if panel installation is not requested or one (1) MMH if requested; add approximately ten (10) MMH if bearing and TRA are replaced.
Part II: approximately eight (8) MMH without bearing replacement or nine (9) MMH with bearing replacement.
Part III: approximately eight (8) MMH without bearing or TRA replacement, twelve (12) MMH with bearing replacement or fourteen (14) MMH with bearing and TRA replacement.
Part IV: approximately eight (8) MMH.
MMH are based on hands -on time and can change with personnel and facilities available.
H. WEIGHT AND BALANCE N.A.
I. REFERENCES
1) PUBLICATIONS Following Data Modules refer to AMP:
DATA MODULE DESCRIPTION PART DM01 39-A-00-20-00-00A-120A-A Helicopter on ground for a safe maintenance
I, II, III, IV DM02 39-A-06-41-00-00A-010A-A Access doors and panels - General data I, III DM03 39-A-20-00-00-00A-69CA-A Assembled parts - Slippage Marks I DM04 39-A-64-31-04-00A-520A-A Sliding control assembly - Remove procedure
I, II, III, IV DM05 39-A-64-31-04-01A-320A-B Duplex bearing (sliding control assembly) - Operation test II DM06 39-A-67-32-01-00A-520A-A Tail rotor servoactuator - Remove procedure I, III DM07 39-A-67-32-01-00A-720A-A Tail rotor servoactuator - Install procedure I, III DM08 39-A-64-31-04-00A-720A-A Sliding control assembly - Install procedure
I, II, III, IV DM09 39-A-64-31-03-00A-520A-A Cover - Remove procedure III DM10 39-A-64-31-03-00A-720A-A Cover - Install procedure III
S.B. N°139-725 EMERGENCY ALERT DATE: July 25, 2022 Page 6 of 20 REVISION: A - August 9, 2022
DATA MODULE DESCRIPTION PART DM11 39-A-64-31-04-01A-921A-B Duplex bearing (sliding control assembly) - Replacement (remove and install a new item)
I, II, III, IV
2) ACRONYMS & ABBREVIATIONS AMDI Aircraft Material Data Information AMP Aircraft Maintenance Publication AMPI Aircraft Maintenance Planning Information DM Data Module DOA Design Organization Approval EASA European Aviation Safety Agency FH Flight Hours IPD Illustrated Parts Data ITEP Illustrated Tools and Equipment Publication LHD Leonardo Helicopters Division MMH Maintenance Man Hours MMIR Maintenance Malfunction Inspection Report P/N Part Number PCR Pitch Control Rod S/N Serial Number TRA Tail Rotor Actuator
3) ANNEX N.A.
J. PUBLICATIONS AFFECTED AW139 AMPI Chapter 5.
K. SOFTWARE ACCOMPLISHMENT SUMMARY N.A.
S.B. N°139-725 EMERGENCY ALERT DATE: July 25, 2022 REVISION: A - August 9, 2022 Page 7 of 20
2. MATERIAL INFORMATION A. REQUIRED MATERIALS
1) PARTS PART I # P/N ALTERNATIVE P/N DESCRIPTION Q.TY LVL NOTE LOG P/N 1 3G6430V00153 Duplex bearing 1 . (1) - 2 3G6730V00732 Tail rotor actuator 1 . (1) -
PART II # P/N ALTERNATIVE P/N DESCRIPTION Q.TY LVL NOTE LOG P/N 3 3G6430V00153 Duplex bearing 1 . (1) -
PART III # P/N ALTERNATIVE P/N DESCRIPTION Q.TY LVL NOTE LOG P/N 4 3G6430V00153 Duplex bearing 1 . (1) - 5 3G6730V00732 Tail rotor actuator 1 . (1) -
PART IV # P/N ALTERNATIVE P/N DESCRIPTION Q.TY LVL NOTE LOG P/N 6 3G6430V00153 Duplex bearing 1 . -
Refer also to IPD for the spares materials required to comply with the AMP DMs referenced in the accomplishment instructions.
2) CONSUMABLES The following consumable materials, or equivalent, are necessary to accomplish this Service Bulletin:
# Spec./LHD code number DESCRIPTION Q.TY NOTE PART 7 TT-N-95-B / Code No. 531055030 Aliphatic Naphtha (C059) AR (2) II, III 8 DX 70002 Marking paint (C263) AR (2) I
Refer to AMDI for the consumable materials required to comply with the AMP DM referenced in the accomplishment instructions.
3) LOGISTIC MATRIX N.A.
NOTE
(1) Item required only in case its replacement is needed because of a failed inspection.
(2) Item to be procured as local supply.
S.B. N°139-725 EMERGENCY ALERT DATE: July 25, 2022 Page 8 of 20 REVISION: A - August 9, 2022
B. SPECIAL TOOLS The following special tools, or equiva lent, are necessary to accomplish this Service Bulletin:
# P/N DESCRIPTION Q.TY NOTE PART 9 Commercial Light source 1 (B1) I 10 Commercial Transparent container 1 (B1) II, III 11 Commercial Spatula 1 (B1) II, III 12 Commercial Magnet 1 (B1) II, III 13 3G6405G04032 Tool kit, T/R duplex bearing removal/installation 1 (B2) I, II, III, IV
Refer to ITEP for the special tools required to comply with the AMP DM referenced in the accomplishment instructions.
SPECIAL TOOLS NOTE Item to be procured as local supply.
Item needed only if bearing replacement is required.
C. INDUSTRY SUPPORT INFORMATION Owners/Operators who comply with the instructions of this Service Bulletin no later than the applicable date in the “Compliance ” section will be eligible to receive required materials on free of charge basis, except for Consumable Materials and Special Tools.
NOTE: Customers who fail to comply with the instructions in this Service Bulletin before the compliance date are not eligible for the aforementioned special policy.
If any of the inspections prescribed in Part I, Part II or Part III fails, please Issue relevant MMIR form to your Warranty Administration Dpt. Including the following information/documents:
- Pictures of sliding control assembly P/N 3G6430A02531;
- Log card of sliding control assembly P/N 3G6430A02531;
- Inspection Report in Figure 4, completed in every part;
- Evidence of reinstallation of the bearing, if applicable;
- Picture of Pin’s rotation on TRA P/N 3G6730V 00731 or P/N 3G6730V00732, only if rotation in found following the related inspection required on Part I and Part III.
If all the required documentation will not be provided, MMIR will be rejected.
NOTE: WRM will include RETURN MATERIAL AUTHORIZATION (RMA ) number; the TRA P/N 3G6730V00731 or P/N 3G6730V00732 disembarked from the aircraft has to be returned to LHD within fifteen (15) calendar days after the shipment of the replacement part. In case of missing return within fifteen (15) calendar days, Customer will be invoiced for the price of the replacement part.
S.B. N°139-725 EMERGENCY ALERT DATE: July 25, 2022 REVISION: A - August 9, 2022 Page 9 of 20
3. ACCOMPLISHMENT INSTRUCTIONS
GENERAL NOTE Place an identification tag on all components that are reusable, including the attaching hardware that has been removed to gain access to the modifi cation area and adequately protect them until their later re-use.
PART I
1. In accordance with AMP DM 39-A-00-20-00-00A-120A-A, prepare the helicopter on ground for a safe maintenance. Disconnect the battery, all electrical power sources and/or the external power supply.
NOTE When the inspection is repeated the slippage mark will be present and the removal of the panels may not be necessary as visual access may be possible thru the panels grids.
2. In accordance with AMP DM 39-A-06-41-00-00A-010A-A and with reference to Figure 1, remove all external panels as required to gain access to the area affected by the inspection.
3. With reference to Figure 1 and Figure 2, perform the inspection for rotation between the parts according to the following procedure:
3.1 If Part I is applied for the first time perform the inspection and the slippage marking application according to the following procedure, otherwise skip to step 3.2:
3.1.1 With reference to Figure 2 views B1 and B2, check that the castellated holes of the trunnion are aligned with those of the pitch control rod that goes thru it and check that the cotter pin is perfectly straight and not bended by a rotation movement. If rotation is found skip to step 4.
3.1.2 With reference to Figure 1 view A and in accordance with the applicable steps of AMP DM 39-A-20-00-00-00A-69CA-A apply a slippage mark on the mating edge between the trunnion and the pitch control rod on the rearward facing side, near the cotter pin.
3.1.3 Skip to step 5.
S.B. N°139-725 EMERGENCY ALERT DATE: July 25, 2022 Page 10 of 20 REVISION: A - August 9, 2022
NOTE If necessary, a light source can be used to better lighten the inspection area when looking thru the panels grids.
3.2 If Part I has already been applied before, with reference to Figure 1 view A, check for the alignment of the slippage mark. If rotation is found proceed to step 4, otherwise skip to step 5.
4. Replace the duplex bearing and the TRA in accordance with the following procedure:
4.1 Send pictures of sliding control assembly P/N 3G6430A02531 log card, with indication of bearing FH, evidence of reinstallation of the bearing, if applicable, the Inspection Report in Figure 4 and pictures of the back -end of the TRA with clear evidence of the rotation, as those in Figure 2 views B1 and B2, thru technical query on Leon ardo WebPortal or to Product Support Engineering (engineering.support.lhd@leonardo.com).
4.2 In accordance with AMP DM 39-A-64-31-04-00A-520A-A and with refer ence to Figure 3, remove the sliding control assembly from the helicopter.
4.3 In accordance with AMP DM 39-A-64-31-04-01A-921A-B and with reference to Figure 3, replace the tail rotor duplex bearing with a new item an d discard the removed one.
4.4 In accordance with AMP DM 39-A-67-32-01-00A-520A-A and 39-A-67-32-01-00A-720A-A and with reference to Figure 1, replace the TRA P/N 3G6730V00731 or P/N 3G6730V00732 with a new item. Send the removed TRA to LHD.
4.5 In accordance with AMP DM 39-A-64-31-04-00A-720A-A and with reference to Figure 3, install the sliding control assembly on the helicopter.
5. Return the helicopter to flight configuration and record for compliance with Part I of this Service Bulletin on the helicopter logbook.
6. Send the attached compliance form to the following mail box:
engineering.support.lhd@leonardo.com As an alternative, gain access to My Communications section on Leonardo WebPortal and compile the “Service Bulletin Application Communication”
S.B. N°139-725 EMERGENCY ALERT DATE: July 25, 2022 REVISION: A - August 9, 2022 Page 11 of 20
PART II
1. In accordance with AMP DM 39-A-00-20-00-00A-120A-A, prepare the helicopter on ground for a safe maintenance. Disconnect the battery, all electrical power sources and/or the external power supply.
2. In accordance with AMP DM 39-A-64-31-04-00A-520A-A and with reference to Figure 3, remove the sliding control assembly from the helicopter.
NOTE To perform the inspection of the duplex bearing do not remove it form sliding control assembly P/N 3G6430A02531.
3. Perform the inspection of the duplex bearing in accordance with the following procedure:
3.1 Inspect the visible parts of the duplex bearing (including the seals) for absence of wear, damages, corrosion; if present skip to step 4, otherwise proceed to step 3.2.
3.2 Check the visible part of the duplex bearing for particles absence; if particles are present skip to step 4, otherwise proceed to step 3.3.
3.3 Check for grease leakage on the visible part of the duplex bearing; if any leakage is present proceed to step 3.4, otherwise skip to step 3.6.
3.4 Check if any particle is found in the grease leakage by finger touch; if present skip to step 4, otherwise proceed to step 3.5.
3.5 Perform grease inspection for magnetic/metallic particles according to the following procedure:
3.5.1 Put a small quantity of leaked grease using a small spatula in a transparent container.
3.5.2 Add a solvent (aliphatic naphtha).
3.5.3 Put a magnet on the bottom out side of the container.
3.5.4 Check for presence of magnetic particles in the solution; if present skip to step 4, otherwise proceed to step 3.6.
3.6 In accordance with AMP DM 39-A-64-31-04-01A-320A-B, perform the duplex bearing operation test and check for absence of roughness in its movement; if test fails proceed to step 4, otherwise skip to step 5.
4. Replace the duplex bearing in accordance with the following procedure:
4.1 In accordance with AMP DM 39-A-64-31-04-01A-921A-B and with reference to Figure 3, replace the tail rotor duplex bearing with a new item and discard the removed one.
4.2 Send pictures of sliding control assembly P/N 3G6430A02531 log card, with indication of bearing FH, evidence of reinstallation of the bearing and the
S.B. N°139-725 EMERGENCY ALERT DATE: July 25, 2022 Page 12 of 20 REVISION: A - August 9, 2022
Inspection Report in Figure 4 thru technical query on Leonardo WebPortal or to Product Support Engineering (engineering.support.lhd@leonardo.com).
5. In accordance with AMP DM 39-A-64-31-04-00A-720A-A and with reference to Figure 3, install the sliding control assembly on the helicopter.
6. Return the helicopter to flight co nfiguration and record for compliance with Part II of this Service Bulletin on the helicopter logbook.
7. Send the attached compliance form to the following mail box:
engineering.support.lhd@leonardo.com As an alternative, gain access to My Communications section on Leonardo WebPortal and compile the “Service Bulletin Application Communication”.