TextPartly OCR
Some pages are OCR from a scan. OCR can misread letters and numbers.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'd2657fccef7e5ffc767298c1c0d35941bc4f328aff2b31e673d1098ce0fb8862' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'd2657fccef7e5ffc767298c1c0d35941bc4f328aff2b31e673d1098ce0fb8862' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
N° 1 69-023 DAT E: May 31, 2017 REV. : B -April 16, 2018 Pag e 1 of 138 TITLE ATA 32 - RETRACTABLE LANDING GEAR SYSTEM UPGRADE.
REVISION LOG Revision B is issued to:
- Update the compliance of Part VII in order to match the information reported in AMPI tasks 32-37 and 32-38, for plunger inspection and lubrication.
An appropriate entry should be made in the aircraft log book upon accomplishment.
If ownership of aircraft has changed, please, forward to new owner.
Leonardo S.p.A.
Via Giovanni Agusta, 520 21017 Cascina Costa di Samarate (VA) Italy Tel.: +39 0331 229111 - Fax: +39 0331 229605/222595 ALERT
SERVICE BULLETIN
S.B. N°169-023 ALERT DATE: May 31, 2017 Page 2 of 138 REVISION: B - April 16, 2018
1. PLANNING INFORMATION A. EFFECTIVITY Part I: AW169 helicopters S/N 69011 and S/N 69017.
Part II: AW169 helicopters S/N 69007, S/N 69015, S/N 69018 and S/N 69022.
Part III: AW169 helicopters S/N 69032, S/N 69041 and S/N 69051.
Part IV: AW169 helicopters S/N 69007, S/N 69009, S/N 69011, S/N 69013, S/N 69014, S/N 69015, S/N 69017, S/N 69018, S/N 69020, S/N 69021, S/N 69022, S/N 69023, S/N 69024, S/N 69027, S/N 69032, S/N 69041 and S/N 69051.
Part V: AW169 helicopters S/N 69007, S/N 69009, S/N 69011, S/N 69013, S/N 69014, S/N 69015, S/N 69017, S/N 69018, S/N 69020, S/N 69021, S/N 69022, S/N 69023, S/N 69024, S/N 69025, S/N 69027, S/N 69028, S/N 69031, S/N 69032, S/N 69041, S/N 69042, S/N 69043, S/N 69044 and S/N 69051.
Part VI: AW169 helicopters S/N 69009, S/N 69013, S/N 69014, S/N 69020, S/N 69021, S/N 69023, S/N 69024, S/N 69025, S/N 69027, S/N 69028, S/N 69031, S/N 69042 S/N 69043, S/N 69044 and S/N 69049.
Part VII:All AW169 helicopters equipped with retractable Landing Gear system P/N 6F3200F00311 or P/N 6F3200F00411.
B. COMPLIANCE Part I: within six (6) months since receipt of the initial issue (Rev. /) of this Service Bulletin;
Part II: within six (6) months since receipt of the initial issue (Rev. /) of this Service Bulletin;
Part III: within six (6) months since receipt of the initial issue (Rev. /) of this Service Bulletin;
NOTE Refer to the following compliance for Part IV if the helicopter is already compliant with BT 169-018 or if it’s already equipped with NLG Retracting actuator P/N 6F3230V00532 and MLG Retracting actuators P/N 6F3230V00832 and P/N 6F3230V01032.
Part IV: within two hundred (200) FH or six (6) month s since receipt of the initial issue (Rev. /) of this Service Bulletin, whichever occurs first, and during the same maintenance downtime of Part V;
S.B. N°169-023 ALERT DATE: May 31, 2017 REVISION: B - April 16, 2018 Page 3 of 138 NOTE Refer to the following compliance for Part IV if the helicopter is NOT already compliant with BT 169-018 or if it’s NOT already equipped with NLG Retracting actuator P/N 6F3230V00532 and MLG Retracting actuators P/N 6F3230V00832 and P/N 6F3230V01032.
Part IV: during the same maintenance downtime of the applicable Part I, Part II or Part III;
NOTE Refer to the following compliance for Part V if the helicopter is already compliant with BT 169-018 or if it’s already equipped with NLG Retracting actuator P/N 6F3230V00532 and MLG Retracting actuators P/N 6F3230V00832 and P/N 6F3230V01032 Part V: within two hundred (200) FH or six (6) months since receipt of the initial issue (Rev. /) of this Service Bulletin, whichever occurs first, and during the same maintenance downtime of Part IV;
NOTE Refer to the following compliance for Part V if the helicopter is NOT already compliant with BT 169-018 or if it’s NOT already equipped with NLG Retracting actuator P/N 6F3230V00532 and MLG Retracting actuators P/N 6F3230V00832 and P/N 6F3230V01032 Part V: during the same maintenance downtime of the a pplicable Part I, Part II or Part III;
Part VI: within two hundred (200) FH or six (6) months since receipt of the initial issue (Rev. /) of this Service Bulletin, whichever occurs first.
Part VI shall be performed before Part IV and/or Part V (if applicable), and during the same maintenance downtime;
S.B. N°169-023 ALERT DATE: May 31, 2017 Page 4 of 138 REVISION: B - April 16, 2018 NOTE All helicopters affected by Part VI or all helicopters already operating the retraction of Landing Gear system, shall refer to the following compliance for Part VII.
Part VII: within thirty (30) days or fifty (50) FH si nce receipt of the initial issue (Rev. /) of this Service Bulletin, whichever occurs first, and then every thirty (30) days or fifty (50) FH, whichever occurs first.
NOTE All helicopters not affected by Part VI nor already operating the retraction of Landing Gear system shall refer to the following compliance for Part VII.
Part VII:during the same maintenance downtime of the applicable Part I, Part II or Part III, and then every thirty (30) days or fifty (50) FH, whichever occurs first.
C. CONCURRENT REQUIREMENTS This Service Bulletin cancels and supersedes the BT 169-018 Rev. /.
D. REASON This Service Bulletin is issued in order to provide all necessary instructions on how to p erform the retro-modification of the retractable landing gear system and provides instructions on how to perform the replacement of the existing control box with the latest one by means of the retromod P/N 6F3200P01211 and to install the improved landing gear proximity switch by means of the retromod P/N 6F3200P00211.
E. DESCRIPTION Leonardo Helicopters has developed the present Service bulletin in order to provide all n ecessary instructions to enable the fully functionality of the landing gear system.
In detail:
Part I provides instructions on how to replace the existing Landing Gear actuators with the enhanced version, removing the temporary inhibition of the landing gear retraction introduced by means of the BT 169-005 Rev.A.
Part II provides instructions on how to install the enhanced landing gear retracting actuators, removing the temporary mechanical locking of landing gear, provided with retromodification P/N 6F3200P00411.
S.B. N°169-023 ALERT DATE: May 31, 2017 REVISION: B - April 16, 2018 Page 5 of 138 Part III provides instructions on how to install the enhanced landing gear retracting actuators on all helicopters already equipped with part of the structural provision of the new Nose Landing Gear (NLG) installation.
The enhanced NLG retracting actuator P/N 6F3230V00532 and MLG retracting actuators P/N 6F3230V00832 and P/N 6F3230V01032, introduce improvements on the following items:
output shaft screws: these changes are aimed to improve the torque transmission and the axial support to the bearing;
support bearing: this change is aimed to react the load both in radial and axial direction, thus preventing jamming of the harmonic drive;
internal modification : these changes are aimed to improve the clearance of internal sensing components;
double lever: this change is added to the reaction rod to attenuate the torque perpendicular to the actuator axis.
Part IV provides all the necessary instructions on how to perform the control box modification P/N 6F3200P01211, which allows the replacement of the existing LG control box with the new improved one P/N 6F3230V01233. If LG control box P/N 6F3230V01231 is installed, the removal of the existing retromod P/N 6F3200P00111 is required.
The improved LG control box P/N 6F3230V01233 has the following improvements:
added “idle states” in the logic in order to minimize the effect of unwanted multiple state switch;
added filtering circuit in order to avoid unwanted multiple state switch;
added timeout function in order to protect the actuators;
modified load alleviation angle.
Part V provides all the necessary instructions on how to perform the switch improved landing gear retromod P/N 6F3200P00211.
The switch improved landing gear retromod P/N 6F3200P00211 avoids inadvertent current shut off during extension/retraction and incomplete sequences with no current shut off which may damage the retracting actuator (RA).
In detail:
installation of proximity switch in lieu of the current rotational one: the rotational stiffness of the current switch contrasts lock actuator plunger during extension.
Marginal set up determines wrong indication to the landing gear control module (LGCM) and prevents current shut off to the RA;
S.B. N°169-023 ALERT DATE: May 31, 2017 Page 6 of 138 REVISION: B - April 16, 2018 upper linear switch are used as input for LGCM (during retraction it determines RA current shut off) and proximity switch are for indication only (connected to the landing gear control panel only);
Introduction of a mechanical stop preventing the switch failure.
Part VI provides all the necessary instructions on how to perform installation checks on all helicopters already equipped with the new actuators.
Part VII provides all the necessary instructions on how to perform an inspection on the Up Down Lock Actuator plunger, in order to check the absence of corrosion spots.
F. APPROVAL The technical content of this Service Bulletin is approved under the authority of DOA n
r. EASA.21.J.005. For helicopters registered under other Aviation Authorities, before applying the Service Bulletin, applicable Aviation Authority approval must be checked within Leonardo Helicopters customer portal.
G. MANPOWER To comply with this Service bulletin the following Maintenance-Man-Hours (MMH) are d eemed necessary:
Part I: approximately thirty (30) MMH;
Part II: approximately twenty eight (28) MMH;
Part III: approximately twenty (20) MMH;
Part IV: approximately sixteen (16) MMH;
Part V: approximately one hundred (100) MMH;
Part VI: approximately eight (8) MMH;
Part VII:approximately one (1) MMH;
Maintenance-Man-Hours are based on hands-on time and can change with personnel and facilities available.
H. WEIGHT AND BALANCE NOTE In order to determine the correct value to be listed in Chart A, a configuration check procedure is given, as described below.
PART I
1. If the helicopter is already equipped with Kit Retractable Landing Gear system P/N 6F3200F00411, update the Chart A as described in the following procedure,
S.B. N°169-023 ALERT DATE: May 31, 2017 REVISION: B - April 16, 2018 Page 7 of 138 otherwise skip to step 2:
1.1 The following existing entry in Chart A must be deleted:
P/N 6F3200F00411“Kit Retractable Landing Gear system” WEIGHT (Kg) 178.17 ARM (mm) MOMENT (Kgmm) LONGITUDINAL BALANCE 5026.3 895530.84 LATERAL BALANCE -8.1 -1443.17
1.2 The following entry in Chart A must be added:
P/N 6F3200F00411 + P/N 6F3200P00311 “Kit Retractable Landing Gear system + Enhanced retraction retromod” WEIGHT (Kg) 179.75 ARM (mm) MOMENT (Kgmm) LONGITUDINAL BALANCE 5000.8 898888.79 LATERAL BALANCE -7.4 -1330.14
2. If the helicopter is already equipped with Kit Retractable Landing Gear system P/N 6F3200F00311, update the Chart A as described in the following procedure:
2.1 The following existing entry in Chart A must be deleted:
P/N 6F3200F00311 “Kit Retractable Landing Gear system” WEIGHT (Kg) 177.734 ARM (mm) MOMENT (Kgmm) LONGITUDINAL BALANCE 5033.3 894588.54 LATERAL BALANCE -8.1 -1439.64
2.2 The following entry in Chart A must be added:
P/N 6F3200F00311 + P/N 6F3200P00311 “Kit Retractable Landing Gear system + Enhanced retraction retromod” WEIGHT (Kg) 179,31 ARM (mm) MOMENT (Kgmm) LONGITUDINAL BALANCE 5007.6 897932.78 LATERAL BALANCE -7.5 -1344.85
PART II
1. If the helicopter is already equipped with Kit Retractable Landing Gear system P/N 6F3200F00411, update the Chart A as described in the following procedure, otherwise skip to step 2:
S.B. N°169-023 ALERT DATE: May 31, 2017 Page 8 of 138 REVISION: B - April 16, 2018
1.1 The following existing entry in Chart A must be deleted:
P/N 6F3200F00411 + P/N 6F3200P00411 “Kit Retractable Landing Gear system + LGS, from retract to fixed retromod” WEIGHT (Kg) 154.66 ARM (mm) MOMENT (Kgmm) LONGITUDINAL BALANCE 5024.1 777027.30 LATERAL BALANCE -11.1 -1716.71
1.2 The following entry in Chart A must be added:
P/N 6F3200F00411 + P/N 6F3200P00411 +P/N 6F3200P00711 “Kit Retractable Landing Gear system + Enhanced retraction retromod” WEIGHT (Kg) 180.85 ARM (mm) MOMENT (Kgmm) LONGITUDINAL BALANCE 4982.5 901070.18 LATERAL BALANCE -7.5 1356.35
2. If the helicopter is already equipped with Kit Retractable Landing Gear system P/N 6F3200F00311, update the Chart A as described in the following procedure:
2.1 The following existing entry in Chart A must be deleted:
P/N 6F3200F00311 + P/N 6F3200P00411 “Kit Retractable Landing Gear system + LGS, from retract to fixed retromod” WEIGHT (Kg) 154.23 ARM (mm) MOMENT (Kgmm) LONGITUDINAL BALANCE 5032.2 776086.01 LATERAL BALANCE -11.1 -1711.89
2.2 The following entry in Chart A must be added:
P/N 6F3200F00311 + P/N 6F3200P00411 + P/N 6F3200P00711 “Kit Retractable Landing Gear system + Enhanced retraction retromod” WEIGHT (Kg) 180.41 ARM (mm) MOMENT (Kgmm) LONGITUDINAL BALANCE 4989.3 900129.59 LATERAL BALANCE -7.5 -1353.09
PART III
1. If the helicopter is already equipped with Kit Retractable Landing Gear system P/N 6F3200F00411, update the Chart A as described in the following procedure,
S.B. N°169-023 ALERT DATE: May 31, 2017 REVISION: B - April 16, 2018 Page 9 of 138 otherwise skip to step 2:
1.1 The following existing entry in Chart A must be deleted:
P/N 6F3200F00411 + P/N 6F3200P00411 “Kit Retractable Landing Gear system + LGS, from retract to fixed retromod” WEIGHT (Kg) 154.66 ARM (mm) MOMENT (Kgmm) LONGITUDINAL BALANCE 5024.1 777027.30 LATERAL BALANCE -11.1 -1716.71
1.2 The following entry in Chart A must be added:
P/N 6F3200F00411 + P/N 6F3200P00411 +P/N 6F3200P711 “Kit Retractable Landing Gear system + Enhanced retraction retromod” WEIGHT (Kg) 179.63 ARM (mm) MOMENT (Kgmm) LONGITUDINAL BALANCE 5002.0 898534.27 LATERAL BALANCE -7.8 -1401.15
2. If the helicopter is already equipped with Kit Retractable Landing Gear system P/N 6F3200F00311, update the Chart A as described in the following procedure:
2.1 The following existing entry in Chart A must be deleted:
P/N 6F3200F00311 + P/N 6F3200P00411 “Kit Retractable Landing Gear system + LGS, from retract to fixed retromod” WEIGHT (Kg) 154.23 ARM (mm) MOMENT (Kgmm) LONGITUDINAL BALANCE 5032.2 776086.01 LATERAL BALANCE -11.1 -1711.89
2.2 The following entry in Chart A must be added:
P/N 6F3200F00311 + P/N 6F3200P00411 + P/N 6F3200P00711 “Kit Retractable Landing Gear system + Enhanced retraction retromod” W EIGHT (Kg) 179.2 ARM (mm) MOMENT (Kgmm) LONGITUDINAL BALANCE 5008.9 897594.88 LATERAL BALANCE -7.8 -1397.76
S.B. N°169-023 ALERT DATE: May 31, 2017 Page 10 of 138 REVISION: B - April 16, 2018
PART IV N.A.
PART V N.A.
PART VI N.A.
PART VII N.A.
I. REFERENCES
1) PUBLICATIONS
DATA MODULE DESCRIPTION PART DM01 69-A-00-20-00-00A-120A-A Helicopter on ground for a safe maintenance.
I,II,III,IV,V DM02 69-A-06-40-00-00A-010A-A Access provisions - General data I,II,III DM03 69-A-07-11-00-00A-100A-A Helicopter - Lift on jacks - Operation
I,II,III DM04 69-A-46-26-02-00A-520A-A Number 2 enhanced display control unit (EDCU2) - Remove procedure I,II DM05 69-A-53-17-03-00A-520A-A Lower down panel - Remove procedure I,II DM06 69-A-46-26-02-00A-720A-A Number 2 enhanced display control unit (EDCU2) - Install procedure I,II DM07 69-A-53-17-03-00A-720A-A Lower down panel - Install procedure I,II DM08 69-A-32-31-02-010-941A-A MLG RETRACTING ACTUATOR INSTALLATION - Illustrated Parts Data II,III DM09 69-A-32-63-01-00A-271A-A Nose landing gear micro switch - Adjust II,III DM10 69-A-32-31-00-00A-320A-A Extension and retraction system - Emergency extension circuit - Operation test II,III DM11 69-A-32-31-00-01A-320A-A Extension and retraction system - Emergency extension circuit - Operation test II,III
S.B. N°169-023 ALERT DATE: May 31, 2017 REVISION: B - April 16, 2018 Page 11 of 138
DATA MODULE DESCRIPTION PART DM12 69-A-32-31-02-00A-520A-A Landing gear control box - Remove procedure IV DM13 69-A-32-31-02-00A-720A-A Landing gear control box – Install procedure IV DM14 69-A-32-21-01-00A-520B-A Nose landing gear, retractable - Remove procedure I DM15 69-A-32-21-01-00A-720B-A Nose landing gear, retractable - Install procedure I DM16 69-A-32-31-03-00A-520A-A Nose landing gear actuator - Remove procedure I DM17 69-A-32-31-05-00A-520A-A Left main landing gear actuator - Remove procedure I DM18 69-A-32-31-06-00A-520A-A Right main landing gear actuator - Remove procedure I DM19 69-A-53-15-09-00A-720A-A Double end arm - Install procedure I, VI DM20 69-A-53-15-10-00A-720A-A Double pin arm - Install procedure I, VI DM21 69-A-32-21-01-00A-520A-A Nose landing gear - Remove procedure
II, III DM22 69-A-32-31-12-00A-720A-A MLG Actuator Pin, LH - Install procedure
II, III DM23 69-A-32-31-13-00A-720A-A MLG Actuator Pin, RH - Install procedure
II, III DM24 69-A-32-31-01-00A-520A-A Landing gear control panel - Remove procedure IV, V DM25 69-A-32-31-01-00A-720A-A Landing gear control panel - Install procedure IV, V DM26 69-A-95-63-03-00A-520A-A Left container assy - Remove procedure IV, V DM27 69-A-95-63-03-00A-720A-A Left container assy - Install procedure IV, V DM28 69-A-95-63-04-00A-520A-A Right container assy - Remove procedure V DM29 69-A-95-63-04-00A-720A-A Right container assy - Install procedure V DM30 69-A-32-31-00-00A-320A-A Extension and retraction system - Emergency extension circuit - Operation test
I, II, III DM31 69-A-32-11-01-00A-520B-A Left main landing gear, retractable - Remove procedure
I, II, III DM32 69-A-32-11-01-00A-720B-A Left main landing gear, retractable - Install procedure
I, II, III
S.B. N°169-023 ALERT DATE: May 31, 2017 Page 12 of 138 REVISION: B - April 16, 2018
DATA MODULE DESCRIPTION PART DM33 69-A-32-12-01-00A-520B-A Right main landing gear, retractable - Remove procedure
I, II, III DM34 69-A-32-12-01-00A-720B-A Right main landing gear, retractable - Install procedure
I, II, III DM35 69-A-53-15-05-00A-520A-A Rod assy (retractable) - Remove procedure VI DM36 69-A-53-15-05-00A-720A-A Rod assy (retractable) - Install procedure VI DM37 69-A-53-15-09-00A-520A-A Double end arm - Remove procedure VI DM38 69-A-53-15-10-00A-520A-A Double pin arm - Remove procedure VI DM39 69-A-12-20-07-00A-240A-A LH/RH MLG pintle pin – Lubrication VI DM40 69-A-53-15-06-00A-720A-A NLG lock support assy - Install procedure V
2) ACRONYMS AMDI Aircraft Material Data Information A MP Aircraft Maintenance Publication ASRP Aircraft Structural Repair Publication DM Data Module EDCU Enhanced Display and Control Unit IPD Illustrated Parts Data LG Landing Gear LH Left MLG Main Landing Gear MMH Maintenance-Man-Hours NLG Nose Landing Gear PFD Primary Flight Display RFM Rotorcraft Flight Manual RA Retracting Actuator RH Right WOW Weight-On-Wheel SB Service Bulletin