Text
From the PDF’s text layer: layout, tables and figures are lost. The PDF is the document.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'efe1f95c28f51a7a1128a8d364123e493203a6256a18b727b5db49ebe3d71d79' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'efe1f95c28f51a7a1128a8d364123e493203a6256a18b727b5db49ebe3d71d79' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
N° 189-102 DA TE: July 15, 2016 REV. : A - December 21, 2017 Pa ge 1 of 10 TITLE ATA 62 - MAIN ROTOR (MR) DAMPER
REVISION LOG Revision A:
The helicopters that have complied with Part I of SB189-102 Rev./ shall not comply with Part I of Revision A.
Revision A is issued to allow replacement of MR damper P/N 4F6220V00251 with new MR damper P/N 8G6220V00151.
Revision A also include:
- New Service Bulletin Format
- Instruction to return of MR damper P/N 4F6220V00251 for upgrade to P/N 8G6220V00151.
Revision bars in the margins identify changes.
An appropriate entry should be made in the aircraft log book upon accomplishment.
If ownership of aircraft has changed, please, forward to new owner.
Leonardo S.p.A.
Via Giovanni Agusta, 520 21017 Cascina Costa di Samarate (VA) Italy Tel.: +39 0331 229111 - Fax: +39 0331 229605/222595 ALERT
SERVICE BULLETIN
S.
B. N°189-102 ALERT DATE: July 15, 2016 Page 2 of 10 REVISION: A - December 21, 2017
1. PLANNING INFORMATION A. EFFECTIVITY Part I All AW189 helicopters equipped with MR dampers P/N 4F6220V00251.
Part II All MR dampers P/N 4F6220V00251 equipped with body end P/N M006-01H002-041 or P/N M006-01H002-047.
B. COMPLIANCE NOTE Body end time since new or since overhaul can be computed based on removal/installation data recorded on MR damper logcard Section 2.
Part I After the last flight of the day or within ten (10) flight hours after receipt of this Service Bulletin, whichever occurs later.
Part II Within 30 flight hours from the receipt of this Service Bulletin or when MR dampers body end P/N M006-01H002-041 or P/N M006-01H002-047 reach 500 flight hours since new, whichever occurs later.
C. CONCURRENT REQUIREMENTS N.A.
D. REASON Initial issue This Service Bulletin is issued to introduce a preventive replacement of MR damper P/N 4F6220V00251.
Revision A Revision A is issued to allow replacement of MR damper P/N 4F6220V00251 with new MR damper P/N 8G6220V00151.
E. DESCRIPTION Part I of this Service Bulletin introduces a new lower value of MR damper locking tor que installation on MR hub side and MR lever side, in order to reduce stress.
S.
B. N°189-102 ALERT DATE: July 15, 2016 REVISION: A - December 21, 2017 Page 3 of 10 Part II of this Service Bulletin introduces the replacement for MR dampers P/N 4F6220V00251, with body end that have logged 500 flight hours or more since new.
Revision A is issued to allow in Part II replacement of MR damper P/N 4F6220V00251 with new MR damper P/N 8G6220V00151.
F. APPROVAL The technical content of this Service Bulletin is approved under the authority of DOA nr.
EASA.21.J.005. For helicopters registered under other Aviation Authorities, before applying the Service Bulletin, applicable Aviation Authority approval must be checked within Leonardo Helicopters customer portal.
EASA states mandatory compliance with inspections, modifications or technical directives and related time of compliance by means of relevant Airworthiness Directives.
If an aircraft listed in the effectivity embodies a modification or repair not LHD certified and affecting the content of this Service Bulletin, it is responsibility of the Owner/Operator to obtain a formal approval by Aviation Authority having jurisdiction on the aircraft, for any adaptation necessary before incorporation of the present Service Bulletin.
G. MANPOWER To comply with this Service Bulletin the following Maintenance-Man-Hours (MMH) are dee med necessary:
Part I: approximately ten (10) MMH.
Part II: approximately two (2) MMH for each damper.
Maintenance-Man-Hours are based on hands-on time and can change with personnel and facilities available.
H. WEIGHT AND BALANCE N.A.
I. REFERENCES
1) PUBLICATIONS
DATA MODULE DESCRIPTION PART DM01 89-A-00-20-00-00A-120A-A Helicopter on ground for a safe maintenance.
I,II
S.
B. N°189-102 ALERT DATE: July 15, 2016 Page 4 of 10 REVISION: A - December 21, 2017
DATA MODULE DESCRIPTION PART DM02 89-A-60-80-00-02A-913A-A Attaching parts protective layer - General maintenance procedure I DM03 89-A-62-22-01-00A-520A-A Outboard lightning conductor jumper (damper-to-lever) - Remove procedure I DM04 89-A-62-22-01-00A-720A-A Outboard lightning conductor jumper (damper-to-lever) - Install procedure I DM05 89-A-62-22-03-00A-520A-A Lag damper - Remove procedure II DM06 89-A-62-22-03-00A-720A-A Lag damper - Install procedure II DM07 89-A-62-22-08-00A-520A-A Anti-rotation block - Remove procedure II DM08 89-A-62-22-08-00A-720A-A Anti-rotation block - Install procedure II
2) ACRONYMS AMP Aircraft Maintenance Publication DM D ata Module IPD Illustrated Part Data MMH Maintenance Man Hour MR Main Rotor SB Service Bulletin
3) ANNEX N.A.
J. PUBLICATIONS AFFECTED AW189 Aircraft Maintenance Publication (AMP) AW1 89 Illustrated Part Data (IPD) K. SOFTWARE ACCOMPLISHMENT SUMMARY N.A.
S.B. N°189-102 ALERT DATE: July 15, 2016 REVISION: A - December 21, 2017 Page 5 of 10
2. MATERIAL INFORMATION A. REQUIRED MATERIALS
1) PARTS PART I # P/N ALTERNATIVE P/N DESCRIPTION Q.TY LVL NOTE LOG P/N 1 MS24665-374 Cotter pin 5 .
PART II NOTE MR damper 8G6220V00151 is fully interchangeable and mixable on the same MR hub with a MR damper P/N 4F6220V00251. If a MR damper P/N 8G6220V00151 is furnished to replace a damper P/N 4F6220V00251, also a new anti-rotation block P/N 8G6220A01551 must be supplied to replace the existing one.
# P/N ALTERNATIVE P/N DESCRIPTION Q.TY LVL NOTE LOG P/N 2 4F6220V00251 MR damper AR . (1)(2) / 3 8G6220V00151 MR damper AR . (1)(2) / 4 8G6220A01551 Anti-rotation block AR . (3) /
2) CONSUMABLES N.
A.
3) LOGISTIC MATRIX N.
A.
NOTE
(1) The quantity of the MR damper supplied is between 1 and 5 units depending on the number of damper on which the body end has reached the 500 flight hours and must be replaced.
(2) Both MR dampers P/N 4F6220V00251 with body end P/N M006-01H002-047 that has logged less than 500 flight hours since new, and MR dampers P/N 8G6220V00151 can be installed to comply with this SB.
(3) This item is required when a MR damper P/N 8G6220V00151 is installed.
B. SPECIAL TOOLS
S.
B. N°189-102 ALERT DATE: July 15, 2016 Page 6 of 10 REVISION: A - December 21, 2017 N.A.
C. INDUSTRY SUPPORT INFORMATION Owners/Operators who comply with the instructions of this Bulletin, no later than the app licable date in the “Compliance section” will be eligible to receive REQUIRED MATERIALS on free of charge basis, except for Consumable Materials & Special Tools.
NOTE: Customers who fail to comply with the instructions in this bulletin before the compliance date are not eligible for the aforementioned special policy.
Please Issue relevant M.M.I.R. form ( (M)aintenance (M)alfunction (I)nformation (R)eport ) to your Warranty Administration Dpt..
S.B. N°189-102 ALERT DATE: July 15, 2016 REVISION: A - December 21, 2017 Page 7 of 10
3. ACCOMPLISHMENT INSTRUCTIONS
GENERAL NOTES
a) Place an identification tag on all components that are re-usable, including the attaching hardware that has been removed to gain access to the modification area and adequately protect them until their later re-use.
PART I
1. In accordance with AMP DM 89-A-00-20-00-00A-120A-A, prepare the helicopter on ground for a safe maintenance. Disconnect the battery, all electrical power sources and/or the external power supply.
2. Put the platform (GG-01-00), or an approved alternative, adjacent to the left side of the fuselage.
3. In accordance with AMP DM 89-A-62-22-01-00A-520A-A, remove the outboard lightning conductor jumper.
4. With reference to Figure 1, adjust the tightening torque of the nut P/N MS14144L10 from the bolt P/N 4F6220L00551 that fix the MR damper on the MR hub as follows:
4.1 In accordance with AMP DM 89-A-60-80-00-02A-913A-A, remove the protective layer from the head of the bolt, the nut and the cotter pin.
4.2 Remove the cotter pin P/N MS24665-374 from the nut and the bolt. Discard the cotter pin.
4.3 Remove the nut from the bolt. Do not remove the bolt from the hub.
4.4 Install and tighten the nut P/N MS14144L10 in accordance with the following procedure:
4.4.1 Install the nut removed at step 4.3. Tighten the nut until it is possible to install the related cotter pin.
4.4.2 Record the torque value at which the nut has been tightened. Make sure that the torque value is less than 33.89 Nm (300 lbf in).
4.4.3 Loosen the nut and make sure that the breakaway torque value is more than 3.61 N m (32 lbf in).
4.4.4 Tighten the nut to the final torque value of 74.6 thru 88 Nm (55 thru
64.9 lbf ft) plus the installation torque value recorded at step 4.4.2.
4.4.5 Secure the nut with a new cotter pin P/N MS24665-374.
4.5 In accordance with AMP DM 89-A-60-80-00-02A-913A-A, apply the protective
S.B. N°189-102 ALERT DATE: July 15, 2016 Page 8 of 10 REVISION: A - December 21, 2017 layer to the bolt head, the nut and the cotter pin.
5. With reference to Figure 1, adjust the tightening torque of the nut P/N MS14144L10 from the bolt P/N 4F6220L00451 that fix the MR damper on the MR lever as follows:
5.1 In accordance with AMP DM 89-A-60-80-00-02A-913A-A, remove the protective layer from the head of the bolt, the nut and the cotter pin.
5.2 Remove the cotter pin P/N MS24665-374 from the nut and the bolt. Discard the cotter pin.
5.3 Remove the nut from the bolt. Do not remove the bolt from the hub.
5.4 Install and tighten the nut P/N MS14144L10 in accordance with the following procedure:
5.4.1 Install the nut removed at step 5.3. Tighten the nut until it is possible to install the related cotter pin.
5.4.2 Record the torque value at which the nut has been tightened. Make sure that the torque value is less than 33.89 Nm (300 lbf in).
5.4.3 Loosen the nut and make sure that the breakaway torque value is more than 3.61 N m (32 lbf in).
5.4.4 Tighten the nut to the final torque value of 74.6 thru 88 Nm (55 thru
64.9 lbf ft) plus the installation torque value recorded at step 5.4.2.
5.4.5 Secure the nut with a new cotter pin P/N MS24665-374.
5.5 In accordance with AMP DM 89-A-60-80-00-02A-913A-A, apply the protective layer to the bolt head, the nut and the cotter pin
6. In accordance with AMP DM 89-A-62-22-01-00A-720A-A, install the outboard lightning conductor jumper.
7. Repeat steps 3 thru 6 until you have changed nut torque on all the MR dampers.
8. Remove the platform (GG-01-00) from the left side of the fuselage.
9. Return the helicopter to flight configuration and record for compliance with Part I of this Service Bulletin on the helicopter logbook.
10. Send the attached compliance form to the following mail box:
pse_aw189.mbx.aw@leonardocompany.com As an alternative, gain access to My Communications section on Leonardo WebPortal and compile the “Service Bulletin Application Communication”.
S.B. N°189-102 ALERT DATE: July 15, 2016 REVISION: A - December 21, 2017 Page 9 of 10
PART II
1. In accordance with AMP DM 89-A-00-20-00-00A-120A-A, prepare the helicopter on ground for a safe maintenance. Disconnect the battery, all electrical power sources and/or the external power supply.
2. Identify the MR dampers that install body end P/N M006-01H002-041 or P/N M006-01H002-047 having logged 500 flight hours.
3. In accordance with AMP DM 89-A-62-22-03-00A-520A-A, remove the MR dampers P/N 4F6220V00251 previously identified.
4. Send the removed MR dampers to Leonardo Helicopter customer support. Please refer to your usual contact point in LHD Material Services, in order to arrange the return of replaced items in LHD facility.
NOTE MR damper 8G6220V00151 is fully interchangeable and mixable on the same MR hub with a MR damper P/N 4F6220V00251. If a MR damper P/N 8G6220V00151 is furnished to replace a damper P/N 4F6220V00251, also a new anti-rotation block P/N 8G6220A01551 must be supplied to replace the existing one.
5. In accordance with AMP DM 89-A-62-22-03-00A-720A- A, install the replacement MR dampers as required.
6. If a MR damper P/N 8G6220V00151 will be installed, in accordance with AMP DM 89-A-62-22-08-00A-520A-A and DM 89-A-62-22-08-00A-720A-A, replace the antirotation block with a new one P/N 8G6220A01551.
7. Return the helicopter to flight configuration and record for compliance with Part II of this Service Bulletin on the helicopter logbook.
8. Send the attached compliance form to the following mail box:
pse_aw189.mbx.aw@leonardocompany.com As an alternative, gain access to My Communications section on Leonardo WebPortal and compile the “Service Bulletin Application Communication”.
Non cancellare mai questo segnalibro Non cancellare mai interruzione sezione
Figure 1 S.B. N°189-102 DATE: July 15, 2016 Page 10 of 10 REVISION: A - December 21, 2017
Remarks:
Information:
SERVICE BULLETIN COMPLIANCE FORM Date:
Number:
Revision:
Please send to the following address:
Telephone:
Fax:
B.T. Compliance Date:
Customer Name and Address:
Helicopter Model S/N Total Number Total Hours T.S.O.
LEONARDO S.p.A.
CUSTOMER SUPPORT & SERVICES - ITALY PRODUCT SUPPORT ENGINEERING & LICENSES DEPT.
Via Giovanni Agusta, 520 21017 Cascina Costa di Samarate (VA) - ITALY Tel.: +39 0331 225036 Fax: +39 0331 225988 We request your cooperation in filling this form, in order to keep out statistical data relevant to aircraft configuration up-to-date. The form should be filled in all its parts and sent to the above address or you can communicate the application also via Technical Bulletin Application Communication Section placed in Leonardo AW Customer Portal - MyCommunications Area. We thank you beforehand for the information given.