TextPartly OCR
Some pages are OCR from a scan. OCR can misread letters and numbers.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '5a3f437d10ba5c4ec03e04e1cbc63af8ba5f145ac941fe31e9badc9c33379acb' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '5a3f437d10ba5c4ec03e04e1cbc63af8ba5f145ac941fe31e9badc9c33379acb' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
ERRATA CORRIGE
Please find here attached the page that has to be replaced in the basic Service Bulletin n°189-295 Rev. /.
PAGE 14 “Figure 3”
The description of the bottom picture “VIEW D – INC ORRECT ASSEMBLY PRACTICE” has been changed.
Was:
“GLIDE SLOPE ANTENNA P/N 6208-88-62, ANTENNA CORREC TLY MOUNTED, PRESENCE OF SEALANT IS NOT FOUND”
Becomes:
“GLIDE SLOPE ANTENNA P/N 6208-88-62, ANTENNA INCORR ECTLY MOUNTED, PRESENCE OF SEALANT IS FOUND”
Pa ge 1 of 20 N° 189-295 DA TE: November 29, 2021 REV. : / - March 15, 2017 TITLE ATA 34 – GLIDE SLOPE ANTENNA INSPECTION
REVISION LOG First Issue An appropriate entry should be made in the aircraft log book upon accomplishment.
If ownership of aircraft has changed, please, forward to new owner.
Leonardo S.p.A.
Via Giovanni Agusta, 520 21017 Cascina Costa di Samarate (VA) Italy Tel.: +39 0331 229111 - Fax: +39 0331 229605/222595 ALERT
SERVICE BULLETIN
S.B. N°189-295 ALERT DATE: November 29, 2021 Page 2 of 20 REVISION: /
1. PLANNING INFORMATION A. EFFECTIVITY Part I All AW189 helicopters from S/N 92001 to S/N 92010 equipped with Glide Slope Antenna P/N 6208-88-62 as part of the Kit Glide Slope Antenna P/N 8G3430F00111.
All Glide Slope Antennas P/N 6208-88-62, previously installed on the helicopter, kept in stock.
Part II All AW189 helicopters from S/N 92001 to S/N 92010 equipped with Glide Slope Antenna P/N 6208-88-62 for which the acceptance test procedure prescribed in Part I succeeded, but evidence of sealant was still found after the cleaning procedure.
B. COMPLIANCE Part I Within 200 FH or 6 months, whichever occurs first after the issue of this Service Bulletin.
Before next installation on any helicopter, or within 6 months, whichever occurs first after the issue of this Service Bulletin, for any Glide Slope Antenna P/N 6208-88-62 previously installed on any helicopter and kept in stock.
Part II After 1 year from compliance with Part I.
C. CONCURRENT REQUIREMENTS N.A.
D. REASON This Service Bulletin is issued in order to prescribe a visual inspection of the Glide Slope Antenna P/N 6208-88-62, part of the kit Glide Slope Antenna P/N 8G3430F00111, a corrective action in case the presence of sealant is found and its replacement if the antenna is not operational after the corrective action implementation.
E. DESCRIPTION During the troubleshooting after an unexpected helicopter behavior, the replacement of the Glide Slope Antenna solved the malfunction.
S.B. N°189-295 ALERT DATE: November 29, 2021 REVISION: / Page 3 of 20 A deeper investigation performed by the antenna supplier concluded that the root cause of the event were the two coaxial connectors isolated from their ground plane by the presence of grey mastic.
The design, production and maintenance drawing and instructions did not request any sealant application in this location. As a consequence, LHD decided to issue this SB to check if any other glide slope antenna has a similar sealant application around the connectors.
Part I of this Service Bulletin prescribes the necessary instruction on how to perform the visual inspection to check presence of sealant around the Glide Slope Antenna P/N 6208-88-62. In case of presence of sealant, this SB gives instructions on how to remove the sealant from affected areas, and perform an acceptance test procedure. In case of failure of the acceptance test, this SB gives the instruction of the replacement of the Glide Slope Antenna P/N 6208-88-62 and the n° 2 connectors P/N PE4958 that have been found not operational.
Part II of this Service Bulletin prescribes instructions for the replacement of the Glide Slope Antenna P/N 6208-88-62 and/or the connectors P/N PE4958 that have been found with persistent presence of sealant after Part I, even in case the antenna passed the applicable functional test after cleaning.
F. APPROVAL The technical content of this Service Bulletin is approved under the authority of DOA nr.
EASA.21.J.005. For helicopters registered under other Aviation Authorities, before applying the Service Bulletin, applicable Aviation Authority approval must be checked within Leonardo Helicopters customer portal.
EASA states mandatory compliance with inspections, modifications or technical directives and related time of compliance by means of relevant Airworthiness Directives.
If an aircraft listed in the effectivity embodies a modification or repair not LHD certified and affecting the content of this Service Bulletin, it is responsibility of the Owner/Operator to obtain a formal approval by Aviation Authority having jurisdiction on the aircraft, for any adaptation necessary before incorporation of the present Service Bulletin.
G. MANPOWER To comply with this Service Bulletin, the following MMH are deemed necessary.
Part I: approximately five (5) MMH;
Part II: approximately three (3) MMH;
S.B. N°189-295 ALERT DATE: November 29, 2021 Page 4 of 20 REVISION: / MMH are based on hands-on time and can change with p ersonnel and facilities available.
H. WEIGHT AND BALANCE N.A.
I. REFERENCES
1) PUBLICATIONS Following Data Modules refer to AMP:
DATA MODULE DESCRIPTION PART DM01 89-A-00-20-00-00A-120A-A Helicopter on ground for a safe maintenance.
I, II DM02 89-A-06-41-00-00A-010A-A Access doors and panels – General data I, II DM03 89-A-34-32-01-00A-520A-A Glide slope antenna – Remove procedure I, II DM04 89-A-34-32-01-00A-720A-A Glide slope antenna – Install procedure I, II DM05 89-A-11-00-01-00A-720A-A Decal – Install procedure I, II
2) ACRONYMS & ABBREVIATIONS AMP Aircraft Maintenance Publication DM Data Module DOA Design Organization Approval EASA European Aviation Safety Agency FH Flight Hours ITEP Illustrated Tool and Equipment Publication LHD Leonardo Helicopters Division MMH Maintenance Man Hours P/N Part Number SB Service Bulletin S/N Serial Number
3) ANNEX Annex A AW189 External Glide Slope Antenna Kit Acceptance Test Procedure Annex B SB Application Form – Inspection report
S.B. N°189-295 ALERT DATE: November 29, 2021 REVISION: / Page 5 of 20 J. PUBLICATIONS AFFECTED N.A.
K. SOFTWARE ACCOMPLISHMENT SUMMARY N.A.
S.B. N°189-295 ALERT DATE: November 29, 2021 Page 6 of 20 REVISION: /
2. MATERIAL INFORMATION A. REQUIRED MATERIALS
1) PARTS # P/N ALTERNATIVE P/N DESCRIPTION Q.TY LVL NOTE LOG P/N 1 8G3430F00111 KIT GLIDE SLOPE ANTENNA REF . - - 2 8G3430A00311
GLIDE SLOPE
EQUIPMENT
INSTALLATION REF .. - - 3 6208-88-62 Glide Slope Antenna 1 … (1)(2) - 4 ED300E7 Decal 1 … (1)(2) - 5 MS24693-C278 Screw 6 … (1)(2) - 6 PE4958 Coaxial Connector AR .. (1)(2) -
2) CONSUMABLES The following consumable materials, or equivalent, are necessary to accomplish this Service Bulletin:
# SPEC./LHD CODE NUMBER DESCRIPTION Q.TY NOTE PART 7 TT-I-735, Grade A Isopropyl alcohol (C039) AR (3) I 8 Commercial Soft lint-free cloth (C011) AR (3) I
Refer also to AMDI for the consumable materials required to comply with the AMP DM referenced in the accomplishment instructions.
3) LOGISTIC MATRIX N.A.
NOTE
(1) Refer to “Industry Support Information” section before ordering this item.
(2) Item to be ordered only if acceptance test procedure fails or presence of sealant is still found after cleaning procedure in Part I.
(3) Item to be procured as local supply.
B. SPECIAL TOOLS The following special tool, or equivalent, is necessary to accomplish this Service Bulletin, in case the visual inspection identifies presence of sealant:
# P/N DESCRIPTION Q.TY NOTE PART 9 - Plastic scraper 1 - I
Refer also to ITEP for the special tools required to comply with the AMP DM referenced in the accomplishment instructions.
S.B. N°189-295 ALERT DATE: November 29, 2021 REVISION: / Page 7 of 20 C. INDUSTRY SUPPORT INFORMATION Owners/Operators who comply with the instructions of this Service Bulletin no later than the applicable date in the “Compliance” section will be eligible to receive “Required Materials” on free of charge basis.
Consumables, Special Tools, and materials required by AMP DM recalled in this SB are not included in the aforementioned policy.
NOTE: Customers who fail to comply with the instructions in this Service Bulletin before the compliance date are not eligible for the aforementioned special policy.
Please Issue relevant MMIR form to your Warranty Administration Dpt.
NOTE: Filling the form in ANNEX B with the evidence of incorrect assembly practice is mandatory; in case the MMIR is not accompanied by this document, it will be rejected.
S.B. N°189-295 ALERT DATE: November 29, 2021 Page 8 of 20 REVISION: /
3. ACCOMPLISHMENT INSTRUCTIONS
GENERAL NOTES
a) Place an identification tag on all components that are re-usable, including the attaching hardware that has been removed to gain access to the modification area and adequately protect them until their later reuse.
b) Shape the cables in order to prevent interference with the structure and the other existing installations, using where necessary suitable lacing cords and plastic cable tiedown.
PART I NOTE Skip steps 1 thru 4 for Glide Slope Antennas P/N 6208-88-62 kept in stock.
1. In accordance with AMP DM 89-A-00-20-00-00A-120A- A, prepare the helicopter on ground for a safe maintenance. Disconnect the battery, all electrical power sources and/or the external power supply.
2. In accordance with AMP DM 89-A-06-41-00-00A-010A-A and with reference to Figure 1, gain access to the Glide Slope Antenna P/N 6208-88-62.
3. In accordance with AMP DM 89-A-34-32-01-00A-520A-A and with reference to Figure 1 Detail A, remove the Glide Slope Antenna P/N 6208-88-62. Keep the hardware for later reuse.
4. With reference to Figures 1 thru 3, perform a visual inspection looking for any evidence of sealant on the following components:
n°2 coaxial connectors P/N PE4958 Antenna Support Assy P/N 8G5315A30231.
5. With reference to Figures 1 thru 3, perform a visual inspection looking for any evidence of sealant around the connectors of the Glide Slope Antenna P/N 6208-88-62.
6. Record the inspection outcome on the report in ANNEX B and continue the procedure according to the following instructions:
6.1 If presence of sealant is not found:
S.B. N°189-295 ALERT DATE: November 29, 2021 REVISION: / Page 9 of 20
6.1.1 For Glide Slope Antennas P/N 6208-88-62 that were installed on the helicopter at the beginning of the accomplishment instructions go to step
7.
6.1.2 For Glide Slope Antennas P/N 6208-88-62 kept in stock go to step 13.
6.2 If presence of sealant is found, with reference to ANNEX B, record the presence of sealant in the SB application form and proceed with the following steps.
CAUTION Pay particular attention not to damage any components during the sealant removal.
CAUTION Pay attention not to remove the paint from the aluminium antenna support during the sealant removal.
6.3 With reference to Figures 1 thru 3, carefully re move the sealant on all affected components by means of a plastic scraper and a lint-free cloth (C011) moistened with isopropyl alcohol (C039).
6.4 After the sealant removal, check that the connector platting is not damaged and that no residue remains inside the RF connectors.
NOTE If step 6.5.2 applies, the helicopter has to comply with Part II of this SB. Check the COMPLIANCE section for the applicable scheduling.
6.5 With reference to Figures 1 thru 3, perform agai n the inspection on n°2 coaxial connectors P/N PE4958 and on the Glide Slope Antenna P/N 6208-88-62.
6.5.1 If presence of sealant is not found after cleaning, go to step 7.
6.5.2 If presence of sealant is still found, either on the antenna or on the coaxial connector(s), even after cleaning, record the persistent presence of sealant in the report in ANNEX B.
7. In accordance with AMP DM 89-A-34-32-01-00A-720A-A and with reference to Figure 1 Detail A, install the Glide Slope Antenna P/N 6208-88-62 by means of existing hardware.
8. In accordance with ANNEX A, perform the External Glide Slope Antenna kit acceptance test procedure and record the test outcome in the report in ANNEX B.
8.1 If the External Glide Slope Antenna kit acceptance test procedure succeeds, go to step 12.
8.2 If the External Glide Slope Antenna kit acceptance test procedure fails replace both the Glide Slope Antenna P/N 6208-88-62 and n° 2 coaxial connectors P/N PE4958
S.B. N°189-295 ALERT DATE: November 29, 2021 Page 10 of 20 REVISION: / according to the following steps.
9 . In accordance with AMP DM 89-A-34-32-01-00A-520A-A and with reference to Figure 1 Detail A, remove the Glide Slope Antenna P/N 6208-88-62, and discard the existing hardware.
10. With reference to Figures 1 and 2, replace the Glide Slope Antenna P/N 6208-88-62 and n°2 coaxial connectors P/N PE4958 as follows:
10.1 In accordance with AMP DM 89-A-34-32-01-00A-720A-A and with reference to Figure 1 Detail A, install the new Glide Slope Antenna P/N 6208-88-62 by means of n°6 screws P/N MS24693-C278.
10.2 In accordance with AMP DM 89-A-11-00-01-00A-720A-A and with reference to Figure 1 Detail A, install the decal P/N ED300E7.
10.3 With reference to Figure 1 replace the n°2 coaxial connectors P/N PE4958.
11. In accordance with ANNEX A, perform the External Glide Slope Antenna kit acceptance test procedure.
12. Return the helicopter to flight configuration and record for compliance with Part I of this Service Bulletin on the helicopter logbook.
13. Send the attached compliance form, report in ANNEX B and pictures to the following mail box:
engineering.support.lhd@leonardocompany.com As an alternative to filling the compliance form, gain access to My Communications section on Leonardo WebPortal and compile the “Service Bulletin Application Communication”.
S.B. N°189-295 ALERT DATE: November 29, 2021 REVISION: / Page 11 of 20
PART II
1. In accordance with AMP DM 89-A-00-20-00-00A-120A-A, prepare the helicopter on ground for a safe maintenance. Disconnect the battery, all electrical power sources and/or the external power supply.
2. In accordance with AMP DM 89-A-34-32-01-00A-520A-A and with reference to Figure 1 Detail A, remove the Glide Slope Antenna P/N 6208-88-62, and discard the existing hardware.
3. With reference to Figures 1 and 2, replace the Glide Slope Antenna P/N 6208-88-62 and/or coaxial connector P/N PE4958 as follows:
3.1 In accordance with AMP DM 89-A-34-32-01-00A-720A-A and with reference to Figure 1 Detail A, install the new Glide Slope Antenna P/N 6208-88-62 by means of n°6 screws P/N MS24693-C278.
3.2 In accordance with AMP DM 89-A-11-00-01-00A-720A-A and with reference to Figure 1 Detail A, install the decal P/N ED300E7.
3.3 With reference to Figure 1 replace the coaxial connector P/N PE4958.
4. In accordance with ANNEX A, perform the External Glide Slope Antenna kit acceptance test procedure.
5. Return the helicopter to flight configuration and record for compliance with Part II of this Service Bulletin on the helicopter logbook.
6. Send the attached compliance form and report in ANNEX B to the following mail box:
engineering.support.lhd@leonardocompany.com As an alternative to filling the compliance form, gain access to My Communications section on Leonardo WebPortal and compile the “Service Bulletin Application Communication”.
Non cancellare mai questo segnalibro Non cancellare mai interruzione sezione