Text
From the PDF’s text layer: layout, tables and figures are lost. The PDF is the document.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'abffe373bfe03f8d621ab8ca1784da22c7888889d244e6fd07108b530fe2177c' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'abffe373bfe03f8d621ab8ca1784da22c7888889d244e6fd07108b530fe2177c' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
Page 1 of 10
BOLLETTINO TECNICO The technical content of this document is approved under the authority of DOA nr. EASA.21J.005.
N° 412-146 DATE July 06, 2016 REV. A July 07, 2016 Comp liance with this bulletin is:
SUBJECT: INSPECTION OF THE SPIRAL BEVEL GEAR P/N 204-040-701 -103 OF THE MAIN TRANSMISSION.
REASON: Introduction of additional inspections of spiral bevel gear P/N 204-040-701-103.
HELICOPTERS AFFECTED:
PARTI I:
AB412 helicopters up to S/N 25669.
PART II:
AB412 helicopters up to S/N 25669 that install the spiral bevel gear P/N 204-040-701 -103 with serial numbers included in Table 1.
SPIRAL BEVEL GEAR S/N SPIRAL BEVEL GEAR S/N SPIRAL BEVEL GEAR S/N A0616 A2 0648 C45371 A0617 A2 0650 C45372 A0618 A2 0651 C45373 A0619 A2 0652 C45374 A0620 A2 0653 C45375 A0621 A2 0659 C45376 A0624 A2 0660 C45377 A0628 A2 0661 C45378 A0629 B27327 C45379 A0631 B27329 E28464 A0635 B27330 E28465 A0637 B27333 B27326 A2 0644 B27337 B27335 A2 0646 C45369 A2 0647 C45370 Table 1
MANDATORY An appropriate entry should be made in the aircraft log book upon accomplishment.
If ownership of aircraft has changed, please, forward to new owner.
Finmeccanica S.p.A.
Via Giovanni Agusta, 520 21017 Cascina Costa di Samarate (VA) Italy Tel.: +39 0331 229111 - Fax: +39 0331 229605/222595 ALERT ALERT
B.T. 412-146 Page 2 of 10 COMPLIANCE:
PART I:
Within the next 10 flight hours after the issue of this Bollettino.
PART II:
For the affected spiral bevel gear P/N 204-040 -701-103 that have accumulated 1.200 FH or more, within the next 100 flight hours after accomplishment of PART I, and subsequently every 300 flight hours.
For the affected spiral bevel gear P/N 204-040-701 -103 that have less of 1.200 FH at the reaching of 1.200 FH and subsequently every 300 flight hours.
DESCRIPTION:
During accomplishment of a main transmission P/N 212-040 -001-59 overhaul, a crack on spiral bevel gear P/N 204-040-701-103 was found.
The preliminary investigations show that the crack was originated from the bottom of one of 32 threaded holes and that other spiral bevel gears manufactured with the same process could be subject to a similar event. This Bollettino therefore requires an unscheduled inspection of the spiral bevel gear P/N 204-040 -701-103 installed on AB412 helicopters in order to detect the parts with serial numbers identified in Table 1 and, for the affected parts, a repetitive inspection for cracks.
The revision A is issued to update the list of spiral bevel gear serial numbers (Table 1) and to define the warranty policy.
MANPOWER REQUIRED:
PART I: Approximately 2 man-hours are required to complete Part I of this Bollettino.
PART II: Approximately 32 man-hours are required to complete Part II of this Bollettino.
This estimate is based on hands-on time, and may vary with personnel and facilities available.
B.T. 412-146 Page 3 of 10 WARRANTY:
Owners/Operators who comply with the instructions of this Bollettino, according to the “Compliance section” will be eligible to receive REQUIRED MATERIALS on free of charge basis, except for Consumable Materials and Special Tools.
NOTE: Customers who fail to comply with the instructions in this Bollettino before the compliance number of Flight Hours are not eligible for the aforementioned special policy.
Please Issue relevant M.M.I.R. form ( (M)aintenance (M)alfunction (I)nformation (R)eport ) to your Warranty Administration Dpt.
MATERIAL REQUIRED:
PART I:
The following material is required for the accomplishment of this Bollettino.
PART II:
N.A.
SPECIAL TOOLS:
Endoscope IPLEX MXII - IV8415M or equivalent.
T100929 Jackscrew or equivalent.
WEIGHT AND BALANCE CHANGE:
N.A.
REFERENCES:
AB412-IPC Illustrated Parts Catalogue AB412-MM Maintenance Manual BHT-ALL-SPM Standard Practice Manual BHT-412-CR&O Component Repair and Overhaul Manual PUBBLICATIONS AFFECTED:
AB412-MPM Maintenance Planning Manual P/N DENOMINATION Q.TY MS29561-248 O-Ring 1
B.T. 412-146 Page 4 of 10 ACCOMPLISHMENT INSTRUCTIONS:
PART I:
1. Prepare the helicopter for safe ground maintenance, disconnect battery and all the electric power source and/or the external power supply.
2. Gain access to transmission area (RH side) removing forward pylon fairing and RH transmission fairing in accordance with AB412-MM.
3. Gain access to RH transmission quill port cover removing RH pylon bulkhead door as indicate in Figure 1 and in accordance with AB412-MM.
4. Remove the transmission quill port cover (ref. Figure 1) in accordance with AB412 -MM Chapter 63-26.
5. Insert the endoscope in the transmission as shown in Figure 2. Place the endoscope to the top of the transmission.
6. To find the serial number on the spiral bevel gear rotate slowly the tail rotor blades until the serial number appears on the screen. The serial number is marked on the edge of the spiral bevel gear as shown in Figure 2 and in Figure 3a. As alternate, the serial number could be located as shown in Figure 3b.
NOTE Each spiral bevel gear is marked with the part number, with the FHD Manufacturer Code A0126 and with the serial number.
7. Record the spiral bevel gear part number and serial number in the applicable Main Transmission documents.
8. If the serial number identified is not included in Table 1, no further actions are required proceed in accordance with step 13.
9. If the serial number is included in Table 1, mark one tooth of the spiral bevel gear with white chalk (or equivalent) as shown in Figure 4.
10. With the aid of a light source, by rotating the tail rotor blades, visually inspect the teeth of the spiral bevel gear for presence of cracks.
11. If cracks are found, remove the spiral bevel gear from service and replace it with an airworthy spiral bevel gear. Report inspection findings to FHD Product Support Engineering at the following e-mail address absereng.AW@leonardocompany.com
12. If cracks are not found, proceed in accordance with the following steps.
13. Re-install the transmission quill port cover in accordance with AB412-MM Chapter 63-26.
14. Re-install the RH pylon bulkhead door in accordance with AB412-MM.
B.T. 412-146 Page 5 of 10
15. Re-install the forward pylon fairing and RH transmission fairing in accordance with AB412- MM.
16. Return the helicopter to a ready to flight condition.
17. Record compliance with PART I of th is Bollettino in the applicable Main Transmission documents.
PART II
1. Prepare the helicopter for safe ground maintenance, disconnect battery and all the electric power source and/or the external power supply.
2. In accordance with AB412-MM Chapter 63-22 remove the transmission from the helicopter.
3. Remove the spiral bevel gear P/N 204-040 -701-103 from transmission (ref. BHT-412-CR&O Chapter 63-00) and perform Fluorescent Magnetic Particle Inspection (ASTM-E-1444) i n accordance with BHT-412-CR&O Table 63-3 and BHT-ALL-SPM Chapter 6-00 para. 6-17 .
(Refer to Figure 5 and Figure 6 for typical crack found during inspection).
4. If after inspection cracks are found, remove the spiral bevel gear from service and replace it with an airworthy spiral bevel gear. Report inspection findings to FHD Product Support Engineering at the following e-mail address absereng.AW@leonardocompany.com
5. If after inspection no cracks are found, reinstall spiral bevel gear P/N 204-040 -701-103 and re-assembly the transmission in accordance with BHT-412-CR&O Chapter 63-00.
6. In accordance with AB412-MM Chapter 63-22 re-install the transmission on the helicopter.
7. Return the helicopter to a ready to flight condition.
8. Record compliance with PART II of this Bollettino in the applicable Main Transmission documents.
B.T. 412-146 Page 6 of 10 Figure 1 – View from RH pylon bulkhead door
QUILL PORT COVER
B.T. 412-146 Page 7 of 10 Figure 2
S/N SPIRAL BEVEL GEAR
B.T. 412-146 Page 8 of 10 Figure 3a Figure 3b
ALTERNATIVE
S/N LOCATION
S/N LOCATION (see Detail A) Detail A - Edge of spiral bevel gear
B.T. 412-146 Page 9 of 10
Figure 4
MARKING OF ONE TOOTH
OF THE SPIRAL BEVEL
GEAR WITH A WHITE CHALK
B.T. 412-146 Page 10 of 10 Figure 5 – Crack on spiral bevel gear P/N 204-040-701-103 Figure 6 – Crack on spiral bevel gear P/N 204-040-701-103
Remarks:
Information:
BOLLETTINO TECNICO COMPLIANCE FORM Date:
Number:
Revision:
Please send to the following address:
Telephone:
Fax:
B.T. Compliance Date:
Customer Name and Address:
Helicopter Model S/N Total Number Total Hours T.S.O.
FINMECCANICA S.p.A.
CUSTOMER SUPPORT & SERVICES - ITALY PRODUCT SUPPORT ENGINEERING & LICENSES DEPT.
Via Giovanni Agusta, 520 21017 Cascina Costa di Samarate (VA) - ITALY Tel.: +39 0331 225036 Fax: +39 0331 225988 We request your cooperation in filling this form, in order to keep out statistical data relevant to aircraft configuration up-to-date. The form should be filled in all its parts and sent to the above address or you can communicate the application also via Technical Bulletin Application Communication Section placed in Leonardo AW Customer Portal - MyCommunications Area. We thank you beforehand for the information given.