Copy · Leonardo Helicopters SB 412-160 Rev 0 · 12 pages

© Leonardo S.p.A. Filed by the FAA in regulations.gov docket FAA-2021-0607, the docket of AD 2021-16-04. Not covered by OpenAirDocs’ CC0 dedication.

Text

From the PDF’s text layer: layout, tables and figures are lost. The PDF is the document.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '925cacd9764e5c1180eb4570336001699e42aa783ae3a2336fa47c29c7783bfd'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

N° 412-160 DATE: August 13, 2020 REV. : / - March 15, 2017 Page 1 of 11 TITLE ATA 24 - EMERGENCY BUS INTERLOCK COMPARTMENT, INSPECTION OF

REVISION LOG New Issue Leonardo S.p.A.

Via Giovanni Agusta, 520 21017 Cascina Costa di Samarate (VA) Italy Tel.: +39 0331 229111 - Fax: +39 0331 229605/222595 An appropriate entry should be made in the aircraft log book upon accomplishment.

If ownership of aircraft has changed, please, forward to new owner.

SERVICE BULLETIN

S.B. N°412-160 DATE: August 13, 2020 Page 2 of 11 REVISION: /

1. PLANNING INFORMATION A. EFFECTIVITY All AB412/AB412EP helicopters.

B. COMPLIANCE Within 25 flight hours or 3 months whichever occurs first after the issue of this Service Bulletin C. CONCURRENT REQUIREMENTS N.A.

D. REASON This Service Bulletin is issued in order to provide the necessary instruction on how to perform a one-off inspection of the grommet installed on the emergency bus interlock compartment at STA 63.30 (1608 mm).

E. DESCRIPTION An AB412EP in service reported the activation of the N o. 1 and N o.2 Inverter Caution Lights on the Warning and Caution Panel, with the consequent Autopilot disengagement.

Further investigation revealed that the cause of the malfunction was a failure for chafing of a wire, part of the AC PWR SYS C/A, due to a protective grommet not properly installed in the emergency bus interlock compartment.

Leonardo Helicopters, as a precautionary measure, issued this Service Bulletin in order to provide the instructions to perform a one -time inspection to verify the existing clearance between grommet and the wires passing through it.

F. APPROVAL The technical content of this Service Bulletin is approved under the authority of DOA nr. EASA.21.J.005. For helicopters registered under other Aviation Authorities, before applying the Service Bulletin, a pplicable Aviation Authority approval must be checked within Leonardo Helicopters customer portal.

EASA states mandatory compliance with inspections, modifications or technical directives and related time of compliance by means of relevant Airworthiness Directives.

If an aircraft listed in the effectivity embodies a modification or repair not LHD certified and affecting the content of this Service Bulletin, it is responsibility of the

S.B. N°412-160 DATE: August 13, 2020 REVISION: / Page 3 of 11 Owner/Operator to obtain a formal approval by Aviation Authority having jurisdiction on the aircraft, for any adaptation necessary before incorporation of the present Service Bulletin.

G. MANPOWER To comply with this Service Bulletin, approximately 0.5 MMH are deemed necessary:

MMH are based on hands -on time and can change wi th personnel and facilities available.

H. WEIGHT AND BALANCE N.A.

I. REFERENCES

1) PUBLICATIONS AB412-MM Maintenance Manual BHT-ELEC-SPM Electrical Standard Practice Manual BHT-ALL-SRM Structural Repair Manual

2) ACRONYMS C/A Cable Assy DOA Design Organization Approval EASA European Aviation Safety Agency LHD Leonardo Helicopters MM Maintenance Manual MMH Maintenance Man Hours P/N Part Number SB Service Bulletin SPM Standard Practice Manual SRM Structural Repair Manual

3) ANNEX N.A.

J. PUBLICATIONS AFFECTED N.A.

K. SOFTWARE ACCOMPLISHMENT SUMMARY N.A.

S.B. N°412-160 DATE: August 13, 2020 Page 4 of 11 REVISION: /

2. MATERIAL INFORMATION A. REQUIRED MATERIALS

1) PARTS The following materials may be necessary to accomplish this Service Bulletin:

# P/N ALTERNATIVE P/N DESCRIPTION Q.TY LVL NOTE LOG P/N 1 M22759/41-18-9 Wire, Electrical AR . - 2 MS21266-1N Grommet AR . -

2) CONSUMABLES The following consumable materials, or equivalent, may be necessary to accomplish this Service Bulletin:

# Spec./LHD code number DESCRIPTION Q.TY NOTE PART 3 Commercial (cod. 500204530) Adhesive EC847/1236 AR (1) - 4 MIL-DTL-81706, class 1A, form III Chemical Film, Alodine 1201 AR (1) - 5 ML-PRF-23377, type I or II, class C2 Epoxy Polyamide Primer AR (1) -

3) LOGISTIC MATRIX N.A.

NOTE Item to be procured as local supply B. SPECIAL TOOLS N.A.

C. INDUSTRY SUPPORT INFORMATION Owners/Operators who comply with the instructions of this Service Bulletin no later than the applicable date in the “Compliance” section will be eligible to receive REQUIRED MATERIALS on free of charge basis, except for Consumable Materials and Special Tools.

NOTE: Customers who fail to comply with the instructions in this Service Bulletin before the compliance date are not eligible for the aforementioned special policy.

Please Issue relevant MMIR form to your Warranty Administration Dpt.

S.B. N°412-160 DATE: August 13, 2020 REVISION: / Page 5 of 11

3. ACCOMPLISHMENT INSTRUCTIONS

GENERAL NOTES

a) Place an identification tag on all components that are re-usable, including the attaching hardware that has been removed to gain access to the modification area and adequately protect them until their later re-use.

b) Shape t he cables in order to prevent interference with the structure and the other existing installations, using where necessary suitable lacing cords.

c) Let adhesive cure at room temperature for at least 24 hours unless otherwise specified.

d) All lengths are in mm.

1. In accordance with the instructions given in the AB412 -MM Maintenance Manual, prepare the helicopter on ground for a safe maintenance; disconnect the battery and any source of electrical power supply.

2. With reference to Figure 1 and in accordance with the instructions given in the AB412-MM Maintenance Manual, gain access to emergency bus interlock compartment (STA 1608).

3. With reference to Figures 2 and 3, verify there is a sufficient clearance between the C/As and the grommet.

3.1 If the clearance is sufficient, proceed to step 4.

3.2 If the clearance is not sufficient:

3.2.1 Remove and discard the existing grommet.

3.2.2 Inspect the indicated C/As for conditions and, in case of damage replace the interested C/As, in accordance with the instructions given in BHT-ELEC-SPM.

3.2.3 With reference to Figure 4, rework the bulkhead in the emergency bus interlock compartment as follow:

3.2.3.1 In accordance with the instructions given in BHT -ALL-SRM remove paint and primer in the area of reworking.

3.2.3.2 Rework the lightening hole as indicated in Figure 4.

3.2.3.3 Deburr the hole and break sharp edges with radius 0.13÷0.38 mm.

S.B. N°412-160 DATE: August 13, 2020 Page 6 of 11 REVISION: /

3.2.3.4 In accordance with the instructions given in BHT -ALL-SRM apply chemical film protection to the reworked area.

3.2.3.5 Prime all bare metal surfaces using epoxy polyamide primer and let dry.

CAUTION Use of adhesive EC847/1236, or equivalent is mandatory.

Pay particular attention during its application to ensure the correct installation of the grommet.

3.2.4 With reference to Figure 5 and in accordance with the instructions given in BHT -ELEC-SPM, install grommet P/N MS21266 -1N with the junction in the upper part, using adhesive EC847/1236. Adapt the grommet dimension during installation.

4. Return the helicopter to a ready to flight condition and record for compliance with this Service Bulletin on the helicopter logbook.

5. Send the attached compliance form to the following mail box:

absereng.aw@leonardocompany.com As an alternative, gain access to My Communications section on Leonardo WebPortal and compile the “Service Bulletin Application Communication”.

 Non cancellare mai questo segnalibro Non .interruzione sezione

Figure 1 S.B. N°412-160 DATE: August 13, 2020 REVISION: / Page 7 of 11

Grommet to be verified Emergency bus interlock compartment

Figure 2 S.B. N°412-160 DATE: August 13, 2020 Page 8 of 11 REVISION: /

Example of correct installation:

sufficient clearance between the C/As and the grommet

Grommet P/N MS35489-23

Figure 3 S.B. N°412-160 DATE: August 13, 2020 REVISION: / Page 9 of 11

Example of incorrect installation:

insufficient clearance between the C/As and the grommet

Figure 4 S.B. N°412-160 DATE: August 13, 2020 Page 10 of 11 REVISION: /

Figure 5 S.B. N°412-160 DATE: August 13, 2020 REVISION: / Page 11 of 11

Remarks:

Information:

SERVICE BULLETIN COMPLIANCE FORM Date:

Number:

Revision:

Please send to the following address:

Telephone:

Fax:

B.T. Compliance Date:

Customer Name and Address:

Helicopter Model S/N Total Number Total Hours T.S.O.

LEONARDO S.p.A.

CUSTOMER SUPPORT & SERVICES - ITALY PRODUCT SUPPORT ENGINEERING & LICENSES DEPT.

Via Giovanni Agusta, 520 21017 Cascina Costa di Samarate (VA) - ITALY Tel.: +39 0331 225036 Fax: +39 0331 225988 We request your cooperation in filling this form, in order to keep out statistical data relevant to aircraft configuration up-to-date. The form should be filled in all its parts and sent to the above address or you can communicate the application also via Technical Bulletin Application Communication Section placed in Leonardo AW Customer Portal - MyCommunications Area. We thank you beforehand for the information given.