Copy · SB382-57-95 · 25 pages

© LOCKHEED MARTIN CORPORATION. Filed by the FAA in regulations.gov docket FAA-2014-0749; AD 2015-05-08 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

TextPartly OCR

Some pages are OCR from a scan. OCR can misread letters and numbers.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = 'fc6ebf0937d7b36f7957df73ec04cc903a2481d4bd5a4ffcbc397a30b331f1f7'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

HERCULES Lockheed Martin Aeronautics Company Marietta, Georgia 30063

SERVICE BULLETIN

EXPORT CONTROLLED INFORMATION WARNING - This document contains data whose export is restricted by the Arms Export Control Act (Title 22, U.S.C., Sec 2751, et seq.) as amended, or the Export Administration Act (Title 50, U.S.C., App 2401 et seq.) as amended. Violations of these export laws are subject to severe criminal and civil penalties.

© 2013 LOCKHEED MARTIN CORPORATION. LOCKHEED MARTIN PROPRIETARY INFORMATION.

December 16, 2013 382-57-95 Page 1 of 17

WINGS - OUTER WING UPPER AND LOWER RAINBOW FITTING INSPECTION FOR CRACKS AND

REPLACEMENT

NOTE: This Service Bulletin includes Appendix A.

1. PLANNING INFORMATION A. EFFECTIVITY This service bulletin is applicable to all Model 382, 382B, 382E, 382F, and 382G series FAA certificated Hercules aircraft having Outer Wing Serials 4542 or later, or all MEP replacement outer wings except the 14Y Series (Part No. 388021-9/-10).

B. REASON

(1) Fatigue cracking of the outer wing upper and lower rainbow fittings on the durability test and on in-service aircraft indicates a requirement to perform inspections of the rainbow fittings. Analysis of in-service cracking has shown that these fittings are susceptible to Multiple Site Damage (MSD) and an inspection is required to ensure that cracking does not occur in the skin panel-to-fitting fastener holes, resulting in an unacceptable reduction in residual strength. The inspection intervals provided in this service bulletin will ensure that the probability of failure remains acceptably low until the rainbow fittings are replaced.

(2) The 14 CFR Part 26, Subpart C Aging Aircraft Safety - Widespread Fatigue Damage rule became effective on January 14, 2011. In compliance with this rule, Lockheed Martin Aeronautics Company established a Limit of Validity (LOV) for 382 series aircraft, published in Section VII of customer specific Service Manual Publication (SMP) 515-C Inspection Programs. 14 CFR Part 121 or Part 129 operators must have incorporated the LOV into their maintenance program by July 14, 2013 to comply with FAR §121.1115 or §129.115. This service bulletin incorporates maintenance actions required for the outer wing rainbow fittings to safeguard the airc raft against widespread fatigue damage up to the LOV.

(3) Lockheed Martin Aeronautics Company recommends that inspections specified herein be accomplished on all commercial aircraft outer wings that have accumulated 30,000 or more flight hours. The initial inspection should be performed at the next convenient maintenance period but not to exceed 365 days or 600 flight hours, whichever occurs first, after receipt of this Service Bulletin. Recurring inspection is recommended at 2,000 flight hours.

(4) Lockheed Martin Aeronautics Company recommends that both upper and lower rainbow fittings be replaced at 50,000 flight hours. This replacement coincides with center wing replacement per Service Bulletin 382-57-94. Replacement of the rainbow fittings will reset the flight hours to zero with respect to the inspection requirements identified in this Service Bulletin .

NOTE: For commercial operators of aircraft with outer wings that have had previous military usage, contact Lockheed Martin for adjusted compliance times.

HERCULES Lockheed Martin Aeronautics Company Marietta, Georgia 30063

SERVICE BULLETIN 382-57-95 USE, COPYING, AND/OR DISCLOSURE IS GOVERN ED BY THE RESTRICTIVE LEGEND ON THE TITLE PAGE OF THIS DOCUMENT. December 16, 2013 Page 2 NOTE: The replacement times indicated in this service bulletin do not apply to military operators of 382, 382B, 382E, 382F, and 382G aircraft. Contact Lockheed Martin for an Operational Usage Evaluation/Service Life Assessment to determine an appropriate replacemen t schedule.

C. DESCRIPTION

(1) This Service Bulletin contains instructions for inspecting outer wing upper and lower rainbow fittings using Eddy Current Surface Scan to detect cracks propagating from fasteners attaching the fittings to skin panels. Perform inspections in accordance with Paragraph 2.A. of this Service Bulletin.

(2) This Service Bulletin contains instructions for replacing upper and lower rainbow fittings on the outer wing. Prior to installation of new rainbow fittings, inspect all open fastener holes in mating structure using Automated Bolt Hole Eddy Current as defined in Appendix A of this Service Bulletin. Make necessary repairs and install new rainbow fittings in accordance with Paragraph 2.B. of this Service Bulletin.

D. APPROVAL

(1) The aircraft owner/operator will make an appropriate entry in the aircraft log records upon compliance with this Service Bulletin.

(2) After the work has been completed on each affected aircraft, please complete and mail or fax (770-494-5682) a Notice of Service Bulletin Compliance; or notify Lockheed Martin Aeronautics Company of compliance with this Service Bulletin at website address:

http://www.lockheedmartin.com/eoc and log into Data Library.

(3) This Service Bulletin has been approved by the FAA as complying with applicable Federal Aviation Regulations.

E. MANPOWER The work prescribed in this Service Bulletin has not been performed at the Lockheed Martin facility.

Therefore, the manpower estimates provided have not been validated, and should not be const rued as being acceptable for use in making fixed price quotes for accomplishment of the work. These estimates are provided only as a convenience for customer planning purposes. It is estimated that manhours required, crew size, and elapsed time while the aircraft is out of service are as follows:

TASK MANHOURS CREW SIZE ELAPSED TIME Primary ECSS Inspection 24 2 12 hrs Removal and Installation of one fitting 515 6 285 hrs Primary BHEC Inspection 24 2 12 hrs

HERCULES Lockheed Martin Aeronautics Company Marietta, Georgia 30063

SERVICE BULLETIN December 16, 2013 USE, COPYING, AND/OR DISCLOSURE IS GOVERNED BY THE REST RICTIVE LEGEND ON THE TITLE PAGE OF THIS DOCUMENT. 382-57-95 Page 3 NOTE: This Service Bulletin is based upon the configuration of the aircraft as it was delivered from Lockheed Martin Aeronautics Company. Previous service bulletins issued by Lockheed Martin Aeronautics Company have been considered in the preparation of this Service Bulletin, but no consideration has been given to peculiar changes made to the aircraft by the owner/operator since its delivery.

F. MATERIAL - COST AND AVAILABILITY

(1) Parts/Materials listed in section 3 of this service bulletin are to be supplied by the a ircraft owner/operator. Parts listed in section 3 of this service bulletin may also be purchased from Lockheed Martin, if desired. Parts bearing Lockheed Martin Aeronautics Company part numbers are considered proprietary and shall be purchased from Lockheed Martin Aeronautics Company unless methods of fabrication are shown in this publication. Inquiries concerning current prices, applicability, and availability of kits may be directed to the following:

MAIL: Lockheed Martin Aeronautics Company C-130 Commercial Contracts Department F532 Zone 0195 86 South Cobb Drive Marietta, GA 30063-0195, USA TELEPHONE: (770) 494-5165 FAX: (817) 655-9700

(2) Additional bulk materials, not included in the kit, will be supplied by the aircraft owner/operator.

G. TOOLING - PRICE AND AVAILABILITY

(1) For ECSS Inspections:

Eddy current inspection unit, Nortec 2000D/D+, or equivalent.

Probe, shielded, right angle, 1/2-inch drop, 50-500 kHz, Fischer/LEMO Triax Connector, Olympus MTF-905-60, or equivalent.

Probe, shielded, straight, 50-500 kHz, Fischer/LEMO Triax Connector, Olympus MTF-40, or equivalent.

Cable, 6 foot, Fischer/LEMO Triax to 16-pin LEMO connector, Olympus P/N 9122244, or equivalent.

Calibration Standard, aluminum, VM Products, Inc. P/N VM30889-C1A or P/N VM30889-C1A/AF, or equivalent.

(2) For BHEC Inspections defined in Appendix A:

Eddy current instrument, Nortec 2000D/D+, or equivalent Scanner, high-speed, MiniMite, 4-pin Fischer, Olympus P/N 9744738, or equivalent.

HERCULES Lockheed Martin Aeronautics Company Marietta, Georgia 30063

SERVICE BULLETIN 382-57-95 USE, COPYING, AND/OR DISCLOSURE IS GOVERN ED BY THE RESTRICTIVE LEGEND ON THE TITLE PAGE OF THIS DOCUMENT. December 16, 2013 Page 4 Probe, bolt hole, shielded reflection (100 kHz–2 MHz), 3/16-inch diameter (.156-.187), 4-pin Fischer, Olympus SPO-5965, P/N 9230061, or equivalent.

Probe, bolt hole, shielded reflection (100 kHz–2 MHz), 1/4-inch diameter (.218-.250), 4-pin Fischer, Olympus SPO-5965, P/N 9219980, or equivalent.

Probe, bolt hole, shielded reflection (100 kHz–2 MHz), 5/16-inch diameter (.281-.312), 4-pin Fischer, Olympus SPO-5965, P/N 9219982, or equivalent.

Probe, bolt hole, shielded reflection (100 kHz–2 MHz), 3/8-inch diameter (.312-.375), 4-pin Fischer, Olympus SPO-5965, P/N 9219982, or equivalent.

Cable, scanner, high-speed, 16-pin Lemo, Olympus P/N 9122090, or equivalent.

Calibration Standard, aluminum, VM Products, Inc. P/N VM30889-C1A or P/N VM30889 C1A/AF, or equivalent.

(3) For Removal and Installation of Rainbow Fitting:

3307043-1/2-16F Fixture to locate the new joint fitting.

3307043-1/2-18F Fixture to mill the nodes of the new joint fitting.

185R105-002A Router, or equivalent, for milling the new joint fitting.

446E101-015C Cutter, or equivalent, for above router.

730M200-004A Depth Micrometer or equivalent.

Jig Transit (with Optical micrometer) or equivalent.

H. WEIGHT AND BALANCE None.

I. REFERENCES SMP 515-C-NDI, Nondestructive Inspection (NDI) Procedures Manual Supplement SMP 581, Hercules Maintenance Manual SMP 583, Structural Repair Manual Hercules Airfreighter Progressive Inspection Procedures Service Bulletin 382-57-94/ Wings - Replacement of Center Wing The following Lockheed Martin drawings may be needed for reference:

DWG NO. DESCRIPTION OUTER WING EFFECTIVITY* 3308150 Outer Wing Assy 4542 thru 4960 3319669 Outer Wing Assy 4992 thru 5320

HERCULES Lockheed Martin Aeronautics Company Marietta, Georgia 30063

SERVICE BULLETIN December 16, 2013 USE, COPYING, AND/OR DISCLOSURE IS GOVERNED BY THE REST RICTIVE LEGEND ON THE TITLE PAGE OF THIS DOCUMENT. 382-57-95 Page 5 DWG NO. DESCRIPTION OUTER WING EFFECTIVITY* 3308152 Box Structure, Outer Wing Assy 4542 thru 4960 3319672 Box Structure, Outer Wing Assy 4992 thru 5320 3308153 LWR Surface Instl 4542 thru 4960 3325532 LWR Surface Instl 4992 thru 5320 3308154 UPR Surface Assy 4542 thru 4960 3325535 UPR Surface Assy 4992 thru 5320 3308155 UPR Surface Instl 4542 thru 4960 3325531 UPR Surface Instl 4992 thru 5320 3308156 LWR Surface Assy 4542 thru 4960 3325536 LWR Surface Assy 4992 thru 5320 370500 Wing Joint Basic Dimension All * Outer wing serial number is indicated on the outer wing identification placard located on the rear beam web near OWS180.

J. OTHER PUBLICATIONS AFFECTED Hercules Airfreighter Progressive Inspection Procedures

HERCULES Lockheed Martin Aeronautics Company Marietta, Georgia 30063

SERVICE BULLETIN 382-57-95 USE, COPYING, AND/OR DISCLOSURE IS GOVERN ED BY THE RESTRICTIVE LEGEND ON THE TITLE PAGE OF THIS DOCUMENT. December 16, 2013 Page 6 THIS PAGE INTENTIONALLY LEFT BLANK.

HERCULES Lockheed Martin Aeronautics Company Marietta, Georgia 30063

SERVICE BULLETIN December 16, 2013 USE, COPYING, AND/OR DISCLOSURE IS GOVERNED BY THE REST RICTIVE LEGEND ON THE TITLE PAGE OF THIS DOCUMENT. 382-57-95 Page 7

2. ACCOMPLISHMENT INSTRUCTIONS A. INITIAL AND RECURRING INSPECTIONS This service bulletin defines the initial inspection for cracks in outer wing upper and lower rainbow fittings on commercial aircraft at 30,000 flight hours and a recurring inspection at intervals of 2,000 flight hours. Perform nondestructive inspection of the outer wing upper and lower rainbow fitting to skin panel attachments, left and right, as shown in Figure 1 and Figure 2. The upper and lower inspection areas are located at OWS 3 to OWS 7 between the forward and aft corner fittings and include 2 inboard chord-wise fastener rows containing approximately 180 fasteners.

The wing joint rainbow fittings are fabricated from 7075-T73511 aluminum. The rainbow fitting tangs taper in thickness from approximately 0.35 to 0.10 inches in the inspection areas. The u pper and lower surface skin panels are attached to the rainbow fittings in the inspection areas with steel fasteners.

Cyclic loading may cause fatigue cracks to begin in the rainbow fitting at the panel attachment fasteners and propagate in a chord-wise direction.

These inspections shall be performed as follows:

NOTE: For support data and locally manufactured items and acceptance/rejection criteria, refer to the SMP 515-C-NDI Nondestructive Inspection Procedures Manual Supplement.

(1) NDI equipment: Required equipment is listed in Paragraph 1.G.(1).

(2) Access: Access to the upper and lower wing surfaces may be accomplished using appropriate maintenance stands. Use safety restraint harnesses or other available safety equipment when working on top of the wings.

(3) Preparation of parts: Remove sealant, scaling paint, oil, and grease in the inspection areas using the procedures detailed in the SMP 515-C-NDI Nondestructive Inspection Procedures Manual Supplement, Section 20-00-00.

(4) Instrument settings/calibration: Set up and calibrate the eddy current instrument as specified in SMP 515-C-NDI Nondestructive Inspection Procedures Manual Supplement, Section 20 -10-04 for eddy current scanning of aluminum. The calibration standard is specified in Paragraph 1.G.(1).

See Figure 3 for the expected signal responses after calibration of the surface scanning probes noted in this inspection.

NOTE: The eddy current instrument must be recalibrated when probes are changed.

(5) Inspection - Upper Surface:

(a) Scan around all fasteners attaching the upper rainbow fitting to the wing skin panels as illustrated in Figure 1. Use the raised fastener heads as a guide when inspecting around the fasteners in the inspection area. Fatigue cracking is expected to propagate in a chord-wise (fore-aft) direction.

(b) An instrument screen presentation, as noted during calibration, will indicate a suspected defect in the part being inspected.

HERCULES Lockheed Martin Aeronautics Company Marietta, Georgia 30063

SERVICE BULLETIN 382-57-95 USE, COPYING, AND/OR DISCLOSURE IS GOVERN ED BY THE RESTRICTIVE LEGEND ON THE TITLE PAGE OF THIS DOCUMENT. December 16, 2013 Page 8

(6) Inspection - Lower Surface:

(a) Scan around all fasteners attaching the lower rainbow fitting to the wing skin panels as illustrated in Figure 2. Use the raised fastener heads as a guide when inspecting around the fasteners in the inspection area. Fatigue cracking is expected to propagate in a chordwise (fore-aft) direction.

(b) An instrument screen presentation, as noted during calibration, will indicate a suspected defect in the part being inspected.

(7) Mark and report suspected defects. If defects are suspected, proceed to the Backup NDI Procedure. If no defects are suspected, complete the Primary NDI Procedure and proceed to System Securing.

(8) BACKUP NDI PROCEDURE

(a) To confirm suspected defects, remove the fastener and perform an Automated Bolt Hole Eddy Current inspection of the open hole in accordance with Appendix A.

(b) Report any damage detected by this inspection procedure to Lockheed Martin Aeronautics Company Enterprise Operations Center in accordance with the note at the end of the accomplishment instructions. Provide the following information for all damage detected:

1 Aircraft Serial Number.

2 Outer Wing Flight Hours (or Aircraft Flight Hours if outer wing hours are unknown).

3 Part number and description.

4 Location (Wing Station, Fuselage Station) and specific fastener hole location.

5 Length, depth, and orientation of crack.

NOTE: Prior to reporting any detected damage to Lockheed Martin Aeronautics Company, it is recommended that a borescope inspection (side view lens) of the hole bore be performed to determine if the reported damage is due to fatigue cracking, embedded metal at fa ying surfaces or mechanical damage (gouging, reamer/drill marks, elongation) within the hole bore.

(9) SYSTEM SECURING. Restore finishes and sealants, reinstall removed components, remove equipment and supplies from the inspection area, and perform operational checkouts as required in accordance with applicable maintenance instructions.

B. REPLACEMENT OF WING JOINT FITTINGS

(1) This Service Bulletin recommends replacement of the outer wing upper and lower rainbow fittings in accordance with Hercules Maintenance Manual on commercial aircraft outer wings having accumulated more than 50,000 total flight hours.

HERCULES Lockheed Martin Aeronautics Company Marietta, Georgia 30063

SERVICE BULLETIN December 16, 2013 USE, COPYING, AND/OR DISCLOSURE IS GOVERNED BY THE REST RICTIVE LEGEND ON THE TITLE PAGE OF THIS DOCUMENT. 382-57-95 Page 9

(2) Preparation for Replacement

(a) Perform Alignment and Symmetry on aircraft in accordance with SMP 583 Structural Repair Manual, Chapter 51-100-00. Retain this data for future reference.

(b) Remove outer wings using instructions in SMP 581 Fig 57-10-03 and place wings on cradle. Secure the cradle with mechanical locks to avoid movement during Step 2.B.(2)(c).

Shoring is required if cradle cannot be mechanically locked.

(c) Conduct a survey of the OWS 0 outer wing joint plane using a suitable optical transit.

Record any disparity in planarity between all nodes. Reference drawings 3308150 and 3319669. Contact Lockheed Martin if the four corner fittings are not co-planar within drawing requirements.

(d) Remove all components such as plumbing and wiring necessary to facilitate installation of replacement rainbow fittings in area between OWS 0 and OWS 7.

(3) Upper Rainbow Fitting Replacement CAUTION: REPLACE UPPER OR LOWER RAINBOW FITTINGS ONE AT A TIME. UNDER NO

CIRCUMSTANCES SHOULD THE RAINBOW FITTINGS AND SPAR CAP CORNER FITTINGS BE REMOVED AT THE SAME TIME. THE CORNER FITTINGS ARE USED

AS A REFERENCE IN THE MACHINING OF THE RAINBOW FITTINGS AND

SHOULD NOT BE REMOVED UNTIL THE MACHINING OF THE RAINBOW FITTINGS HAS BEEN COMPLETED.

CAUTION: EXERCISE CAUTION WHEN INSTALLING OR REMOVING THE NEW RAINBOW FITTING TO AND FROM THE WING. AVOID APPLYING UNDUE FORCE DURING

THIS PROCESS TO PREVENT CRACKING THE FITTING AND OTHER WING COMPONENTS.

(a) Remove upper rainbow fitting by removing attaching fasteners and breaking fay surface sealant. Use caution to avoid damage to wing structure and attach holes.

(b) Clean wing attaching structure such as skin panels, stiffeners, corner fittings, attaching angles, and rib web of sealant and other particles.

(c) Visually inspect the wing faying structure for possible damage or cracks.

(d) Perform Automated Bolt Hole Eddy Current inspection of all open fastener holes in skins, stiffeners, webs, and angles while fitting is removed in accordance with Appendix A of this Service Bulletin. If confirmed cracks are found, repair in accordance with Hercules Structural Repair Manual SMP 583 or contact Lockheed Martin Aeronautics Company Enterprise Operations Center in accordance with the note at the end of the accomplishment instructions.

(e) Place the new rainbow fitting in the wing. Some amount of force may be required to properly align fitting. Reference Drawing 3308154 or 3325535 Upper Surface Assembly.

HERCULES Lockheed Martin Aeronautics Company Marietta, Georgia 30063

SERVICE BULLETIN 382-57-95 USE, COPYING, AND/OR DISCLOSURE IS GOVERN ED BY THE RESTRICTIVE LEGEND ON THE TITLE PAGE OF THIS DOCUMENT. December 16, 2013 Page 10

(f) Install 3307043-1/2-16F Locating Fixture and attach it to the four corner fittings. A shim of suitable size and thickness must be placed between the fixture and each of the four corner fittings to allow the rainbow fitting nodes to protrude for final node milling to assure joint planarity. All four shims must be the same thickness. Reference Drawing 3308152 or 3319672 for wing joint node thickness requirements. All nodes of the rainbow fitting shall be tight against fixture before proceeding.

(g) Check all fitting-to-wing skin panel attaching fastener holes for proper edge distance (1.5 x Final Hole Diameter minimum.)

(h) Visually check the new rainbow fitting for proper placement/alignment prior to drilling operations.

(i) Transfer all fastener holes from outer wing mating structure to new rainbow fi tting in accordance with SMP 583 Structural Repair Manual, Chapter 51-70.

(j) Remove the locating fixture and rainbow fitting from wing. Clean fitting and the surrounding wing area for debris and burrs.

(k) Reposition the new rainbow fitting in the wing, picking up previously drilled holes. Fay surface seal in accordance with SMP 583 Structural Repair Manual.

(l) Wet install oversize fasteners of appropriate type in accordance with SMP 583 Structural Repair Manual, Chapter 51-70.

NOTE: Perform Step 2.B.(4) Lower Rainbow Fitting Replacement before performing Step

2.B.(5) Fitting Node Milling Procedure.

(4) Lower Rainbow Fitting Replacement CAUTION: EXERCISE CAUTION WHEN INSTALLING OR REMOVING THE NEW RAINBOW FITTING TO AND FROM THE WING. AVOID APPLYING UNDUE FORCE DURING

THIS PROCESS TO PREVENT CRACKING THE FITTING AND OTHER WING COMPONENTS.

(a) Remove lower rainbow fitting by removing attaching fasteners and breaking fay surface sealant. Use caution as to not damage wing structure and attach holes.

(b) Clean wing attaching structure such as skin panels, stiffeners, corner fittings, attaching angles, and rib web of sealant and other particles.

(c) Visually inspect the wing faying structure for possible damage or cracks.

(d) Perform Automated Bolt Hole Eddy Current inspection of all open fastener holes in mating structure while fitting is removed in accordance with Appendix A of this service bulletin. If confirmed cracks are found, repair in accordance with Hercules Structural Repair Manual SMP 583 or contact Lockheed Martin Aeronautics Company Enterprise Operations Center in accordance with the note at the end of the accomplishment instructions .

(e) Place the new rainbow fitting in the wing. Some amount of force may be required to properly align fitting. Reference Drawing 3308156 or 3325536 Lower Surface Assembly for proper fit and installation.

HERCULES Lockheed Martin Aeronautics Company Marietta, Georgia 30063

SERVICE BULLETIN December 16, 2013 USE, COPYING, AND/OR DISCLOSURE IS GOVERNED BY THE REST RICTIVE LEGEND ON THE TITLE PAGE OF THIS DOCUMENT. 382-57-95 Page 11

(f) Install P/N 3307043-1/2-16F locating fixture and attach it to the four corner fittings. A shim of suitable size and thickness must be placed between the fixture and each of the four corner fittings to allow the rainbow fitting nodes to protrude for final node milling to assure joint planarity. All four shims must be the same thickness. Reference Drawing 3308152 or 3319672 for wing joint node thickness requirements. All nodes of the rainbow fi tting shall be tight against fixture before proceeding.

(g) Check all fitting-to-wing skin panel attaching fastener holes for proper edge distance (1.5 x Final Hole Diameter minimum)

(h) Visually check the new rainbow fitting for proper placement/alignment prior to drilling operations.

(i) Transfer all fastener holes from outer wing mating structure to new rainbow fitting in accordance with SMP 583 Structural Repair Manual, Chapter 51-70.

(j) Remove the locating fixture and rainbow fitting from wing. Clean components and the surrounding wing area for debris and burrs.

(k) Reposition the new rainbow fitting in the wing, picking up previously drilled holes . Fay surface seal in accordance with SMP 583 Structural Repair Manual.

(l) Wet-install oversize fasteners of appropriate type in accordance with SMP 583 Structural Repair Manual, Chapter 51-70.

NOTE: Continue to Step 2.B.(5) Fitting Node Milling Procedure only after completing Steps

2.B.(3) and 2.B.(4).

(5) Fitting Node Milling Procedure

(a) This step is required for milling procedures: Support the outer wing using instructions in SMP 581 Fig 57-10-03. Secure the cradle with mechanical locks to avoid movement during machining. Shoring is required if cradle cannot be mechanically locked.

(b) Position optical transit as required to adequately read the location of the rainbow fittings.

Adjust the cradle until the four corner fitting node faces are in the same vertical plane . This step will not be necessary if a suitable transit is used that is equipped with degrees of freedom that permit setting the transit line of sight in a non-vertical plane with the four corner fitting nodes. Verify that the four corner fitting nodes are coplanar and check the amount of rainbow fitting node face protrusion. Node thickness requirements are defined by engineering drawing 3308152 and 3319672.

(c) Ensure that Steps 2.(5)(a) and 2.(5)(b) are completed before milling.

(d) Position milling fixture 3307043-1/2-18F Left or Right to the outer wing. Using a proper router with micro depth adjustment as specified in paragraph 1.G.(3), measure the depth to corner fitting nodes. Cross check using the transit. Verify that the milling operation will yield the node thickness requirements as defined by Drawings 3308152 or 3319672. Use router to mill each node.

(e) Continue the same procedure until all upper and lower rainbow fitting nodes are milled to the same plane as the corner fittings. Always cross check optically with transit.

HERCULES Lockheed Martin Aeronautics Company Marietta, Georgia 30063

SERVICE BULLETIN 382-57-95 USE, COPYING, AND/OR DISCLOSURE IS GOVERN ED BY THE RESTRICTIVE LEGEND ON THE TITLE PAGE OF THIS DOCUMENT. December 16, 2013 Page 12

(f) Remove milling fixture.

(g) Ream wing mate holes to final size in accordance with Drawing 370500. Chamfer sharp edges of wing mate holes in accordance with Drawing 3308152 or 3319672.

(h) Touch-up finish the milled nodes with Alodine and one coat of AMS-C-27725 Polyurethane, or equivalent in accordance with Drawings 3308152 or 3319672.

(6) Final Installation

(a) Re-install any components removed to facilitate replacement of the rainbow fittings.

(b) Re-install outer wings per SMP 581, Figure 57-10-03.

(c) Perform an Alignment and Symmetry Check and compare readings to those taken at the start of procedure.

C. RESTORE AIRCRAFT TO SERVICE Perform necessary functional checks of interrupted systems per SMP 581, Figure 57-10-03, Step 39 and return aircraft to service.

NOTE: If assistance is needed, contact your local Lockheed Martin Aeronautics Company Representative, or the Enterprise Operations Center - Technical Support in Marietta, Georgia, USA, as follows:

TELEPHONE: (770) 494-9131

FAX: (770) 494-9122

E-MAIL: hercules.support@lmco.com

MAIL: Lockheed Martin Aeronautics Company 86 South Cobb Drive Dept. 3E1M, Zone 0591 Marietta, GA 30063, USA

Pages 13–24 of 25