Copy · SB 627 C · 8 pages

© Avco Corporation. Filed by the FAA in regulations.gov docket FAA-2016-9512; AD 2017-11-10 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

TextOCR

This text is OCR from a scan. OCR can misread letters and numbers.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '9f619e4298f9b16f071d3cd767ab827ece8bbc7a177c1c15fdd1ce6b44f1dd87'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Page 1OCROpen in PDF

LYCOMING. MANDATORY 652 Oliver Street Williamsport, PA 17701 U.S.A. SERVICE BULLETIN Telephone +1 (800) 258-3279 (U.S. and Canada) Telephone +1 (570) 323-6181 (International) Facsimile +1 (570) 327-7101 www.lycoming.com DATE: November 17, 2016 Service Bulletin No. 627C (Supersedes Service Bulletin No. 627B) Engineering Aspects are FAA Approved SUBJECT: Exhaust System Inspection MODELS AFFECTED: Lycoming Engine Model TIO-540-AJ1A TIME OF COMPLIANCE: Within 10 flight hours from the date of this Service Bulletin, complete an initial Exhaust System Inspection in accordance with the Required Action Steps 1 and 3 in this Service Bulletin After the initial Exhaust System Inspection, subsequent repetitive Exhaust System Inspections are to be completed per Table 1 in this Service Bulletin TREASON FOR REVISION: Changed CO detector lower alarm setting from 35 PPM to 50 PPM; Revised instruction for weld joint examination and included footer on pages 5, 6, and 7 NOTICE: Incomplete review of all the information in this document can cause errors. Read the entire Service Bulletin to make sure you have a complete understanding of the requirements.

This Service Bulletin is in response to field reports of exhaust leaks due to cracked welds and exhaust studs pulling from a cylinder on some Lycoming TIO-540-AJ1A engine models. This Service Bulletin contains instructions for the mandatory inspection of the exhaust system for ALL Lycoming TIO-540-AJ1A engine models per the schedule in Table 1.

Table 1 Schedule for Exhaust System Inspections Engines installed in aircraft Engines installed in aircraft not equipped with a carbon monoxide detector or equipped with an operating with an inoperative carbon monoxide detector carbon monoxide detector* After the initial 10-hour Engines that have accumulated 1000 Exhaust System Inspection, hours or less time in service since the complete the: last Exhaust System Maintenance**

• Exhaust System Inspection After the initial 10-hour Exhaust after every 50 hours time in System Inspection, complete the:

service - complete • Exhaust System Inspection after Required Actions 1 and 3 every 25 hours time in service -

• Torque Check after every complete Required Actions 1 and 3 Engines that have accumulated more than 1000 hours time in service since the last Exhaust System Maintenance** After the initial 10-hour Exhaust System Inspection, complete the:

• Exhaust System Inspection after every 50 hours time in service - complete Required Actions 1 and 3 100 hours time in service - • Torque Check after every 100 complete Required hours time in service - complete Actions 1, 2, and 3 Required Actions 1, 2, and 3

• Torque Check after every 100 hours time in service - complete Required Actions 1, 2, and 3 * An operational carbon monoxide (CO) detector must be an electrochemical CO detector, located on the instrument panel, and set for a lower alarm threshold of 50 parts per million (PPM).

** Since having maintenance that required the removal/reinstallation or the removal and replacement of any exhaust system pipe or turbocharger mounting bracket.

ISSUED REVISED PAGE NO REVISION General Aviation Manufacturers Association MO 07 DAY 18 YEAR 16 MO 11 DAY 17 YEAR 16 1 of 7 C ©2016 Avco Corporation. All Rights Reserved Lycoming Engines is a division of Avco Corporation

Page 2OCROpen in PDF

/ CAUTION: TOXIC GASES, SUCH AS CARBON MONOXIDE, FROM LEAKS IN THE EXHAUST SYSTEM CAN POTENTIALLY ENTER THE COCKPIT.

NOTICE: The inspections in this Service Bulletin are in addition to the requirements of Service Bulletin No. SB-614A and AD 2015-10-06. Both are to be accomplished as specified in their respective compliance times.

Figures in this Service Bulletin are for illustration purposes only; your engine can appear differently.

Required Action

1. Exhaust System Inspection A CAUTION: THE ENGINE AND EXHAUST SYSTEM CAN BE HOT AND COULD CAUSE BURNS. DO NOT CONDUCT THE EXHAUST SYSTEM INSPECTION WITHIN 1 HOUR OF OPERATING THE ENGINE AND UNTIL THE ENGINE AND EXHAUST ARE COOL.

NOTICE: To accurately and efficiently assist those who could be experiencing exhaust leaks due to cracked welds and exhaust studs pulling from a cylinder, Lycoming Engines must collect certain data and information from you each time you complete this inspection.

This inspection can be done on an engine installed in an airframe.

During this exhaust system inspection and each subsequent inspection thereafter per Table 1, complete the steps in this Service Bulletin. Record and submit the findings to Lycoming Engines on the attached form either online or on hardcopy.

NOTICE: It is very important during this inspection to look for and record on the survey any stamped data on the Exhaust No. 2 and 3 pipes.

The stamped markings for Exhaust Pipe 2 will have one of the following:

• Only the part number (P/N) (Figure 1). All pipes will be stamped with at least the P/N.

• The P/N and the Release ID# (Figure 2)

• The P/N, Release ID#, and a date code (Figure 3) 40622318 L0B23386 51953-- Release IDH Figure 1 Figure 2 P/N Only on Exhaust Pipe 2 P/N and Release ID# on Exhaust Pipe 2 0B22318 VEE 519 / 27/16 Release ID # Date Code Figure 3 P/N, Release ID#, and Date Code on Exhaust Pipe 2 A. Examine Exhaust Pipe 2, identify any stamped markings, and record the data on the survey.

ISSUED REVISED PAGE NO REVISION

MO DAY YEAR MO DAY YEAR 2 of 7 C S.B. 627 07 18 16 11 17 16

Page 3OCROpen in PDF

The stamped markings for Exhaust Pipe 3 can have:

• Only the P/N (Figure 4). All pipes will be stamped with at least the P/N.

• The P/N and the Release ID# (Figure 5) (There is no date code on Exhaust Pipe 3) 40B23388 WFP 40B2267 56283-1 Release ID# Figure 4 Figure 5 P/N Only on Exhaust Pipe 3 P/N and Release ID# on Exhaust Pipe 3 B. Examine Exhaust Pipe 3, identify any stamped markings, and record the data on the survey.

C. Examine the weld joints of the exhaust pipes for all cylinders (Figures 6 and 7). Closely examine the saddle reinforced weld joints (Figures 8 and 9), especially at Cylinder 3. If any cracks or damage are found, do not operate the aircraft until repairs are made in accordance with existing Lycoming publications. Complete and submit the survey with your findings and corrective action per Required Action 3 in this Service Bulletin.

Cylinder #1 Exhaust Pipes Cylinder #2 Cylinder #3 Cylinder #6 Cylinder #5 Examine This Saddle Reinforced Weld Joint Exhaust Pipes Turbocharger Mounting Bracket Turbocharger Examine This Saddle Reinforced Weld Joint Turbo Oil Drain Tank Figure 6 Installed Exhaust System (Cylinders #1, #3, #5 - Right Side of Engine) Figure 7 Installed Exhaust System (Cylinders #2, #4, #6 - Left Side of Engine) Figure 8 Figure 9 Saddle Saddle

ISSUED REVISED PAGE NO REVISION

MO DAY YEAR MO DAY YEAR 3 of 7 C S.B. 627 07 18 16 11 17 16

Page 4OCROpen in PDF

D. Examine all cylinder exhaust flanges (Figure

10) for damage, distortion, or signs of exhaust gas leaking past the gasket, especially at Cylinder 2. Indications of a flange gasket leak are burnt paint around the exhaust flange bosses or powdery white to light brown or black residue near the leaks, on the spark plug, and the baffle. If the flange or pipe is distorted, damaged, or there are signs of exhaust leaking past the gasket, do not operate the aircraft until repairs are made in accordance with existing Lycoming publications. Complete and submit the survey Figure 10 with your findings and corrective action per Signs of Exhaust Leak Required Action 3 in this Service Bulletin.

WARNING: DO NOT OPERATE THE AIRCRAFT WITH A LEAKING ENGINE EXHAUST SYSTEM. OPERATION OF THE AIRCRAFT WITH AN EXHAUST SYSTEM

LEAK CAN LEAD TO CARBON MONOXIDE POISONING, LOSS OF CONCIOUSNESS, INJURY, OR DEATH.

E. Complete a visual inspection on the entire exhaust system (Figures 6 and 7). If any sign of leaks, distortion, or damage is found, do not operate the aircraft until repairs are made in accordance with existing Lycoming publications. Complete and submit the survey with your findings and corrective action per Required Action 3 in this Service Bulletin.

2. Flange Nut Torque Check A. Since loose flange nuts can be an indication of a potential exhaust leak, complete a torque check on exhaust system flange nuts for all six cylinders.

B. If a flange, stud, flange nut, or pipe is distorted or visibly damaged, document the issue on the form then replace with serviceable parts. If it is just a leaky gasket, determine root cause, document it on the form, and replace the gasket and hardware with new parts. Do not operate the aircraft until repairs are made in accordance with existing Lycoming publications. Complete and submit the survey with your findings and corrective action per Required Action 3 in this Service Bulletin.

C. On the survey, record the fractional amount each flange nut turns to achieve the required 96 in.- Ib (11 Nm) torque. If any flange nuts are loose enough to allow movement of the washer, contact Lycoming Engines' Product Support.

3. Submit the completed survey after each Exhaust System Inspection and Flange Nut Torque Check to Lycoming Engines either online or by mail.

Online Mail Fill out the online form at Copy and manually complete the hard www.lycoming.com/SB627 copy version of the form in this Service Click on the link or cut and paste Bulletin and send it by postal service to:

into your browser. Technical Support Lycoming Engines 652 Oliver Street Williamsport, PA 17701 USA ISSUED REVISED PAGE NO. REVISION MO DAY YEAR MO DAY YEAR 4 of 7 C S.B. 627 07 18 16 11 17 16

Page 5OCROpen in PDF

Engine Serial Number (Ex. L-12345-61E):

Time Since Last Exhaust System Maintenance:

OWNER INFORMATION Name:

Company:

Address:

City:

State:

Postal Code:

Country:

Telephone Number:

MAINTENANCE PROVIDER INFORMATION Name:

Company:

Address:

City:

State:

Postal Code:

Country:

Telephone Number:

ISSUED REVISED PAGE NO. REVISION

MO DAY YEAR MO DAY YEAR 5 of7 C S.B. 627 07 18 16 11 17 16

Page 6OCROpen in PDF

EXHAUST SYSTEM REVIEW Time Since Exhaust System Maintenance Is there an operable Yes No carbon monoxide detector installed in the aircraft?

Stamped Data on Part Number: Released ID #: Date Code:

Exhaust Pipe 2 Stamped Data on Part Number: Released ID #:

Exhaust Pipe 3 Were any cracks found Yes No on welded joints?

If yes, please describe the location of the crack.

Were any exhaust leaks Yes No found at the cylinder exhaust mounting flange?

What cylinder exhaust 2 4 5 flange was leaking?

(You may select multiple cylinders) Were there any other Yes No exhaust discrepancies found?

If yes, please describe the discrepancies found.

ISSUED REVISED PAGE NO. REVISION MO DAY YEAR MO DAY YEAR 6 of 7 C S.B. 627 07 18 16 11 17 16

Page 7OCROpen in PDF

Did any exhaust flange nuts require more Yes No turning to reach the required torque?

(96in/Ibs) Inboard If yes, which cylinder exhaust flange nuts did you find loose?

Please indicate the amount of movement that you needed to Outboard Outboard tighten the nuts.

CYLINDER 1 N/A < 1/8 Turn 1/8 Turn /¼ Turn ½ Turn > 1/2 Turn Forward Outboard Nut Forward Inboard Nut Aft Outboard Nut Aft Inboard Nut CYLINDER 2 N/A < 1/8 Turn 1/8 Turn ¼ Turn ½ Turn > 1/2 Turn Forward Outboard Nut Forward Inboard Nut Aft Outboard Nut Aft Inboard Nut YLINDER 3 N/A < 1/8 Turn 1/8 Turn ¼ Turn ½ Turn > 1/2 Turn Forward Outboard Nut Forward Inboard Nut Aft Outboard Nut Aft Inboard Nut CYLINDER 4 N/A <1/8 Turn / 8 Turn ¼ Turn ½ Turn > 1/2 Turn Forward Outboard Nut Forward Inboard Nut Aft Outboard Nut Aft Inboard Nut CYLINDER 5 N/A < 1/8 Turn 1/8 Turn ¼ Turn ½ Turn > 1/2 Turn Forward Outboard Nut Forward Inboard Nut Aft Outboard Nut Aft Inboard Nut CYLINDER 6 N/A < 1/8 Turn 1/8 Turn ¼ Turn ½ Turn > 1/2 Turn Forward Outboard Nut Forward Inboard Nut Aft Outboard Nut Aft Inboard Nut ISSUED REVISED PAGE NO. REVISION

MO DAY YEAR MO DAY YEAR 7 of7 S.B. 627 07 18 16 11 17 16

No text on this page: it may be a figure. Open the PDF to see it.