TextPartly OCR
Some pages are OCR from a scan. OCR can misread letters and numbers.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '260c674e063dee75bebe21402f95ac2e2a91236dc15a982fb092d276919e91d7' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '260c674e063dee75bebe21402f95ac2e2a91236dc15a982fb092d276919e91d7' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
652 Oliver Street Williamsport, PA. 17701 U.S.A. SERVICE
INSTRUCTION Tel. 570-323-6181 Fax. 570-327-7101 www.lycoming.com DATE: June 15, 2007 Service Instruction No. 1343B (Supersedes Service Instruction No. 1343A) Engineering Aspects are FAA Approved SUBJECT: Set Screw for Propeller Governor Idler Shaft MODELS AFFECTED: O, IO, LIO, AIO, AEIO-320 Series; O, LO, IO, LIO, AIO, AEIO, TO, TIO- 360 Series; O, IO, AEIO, TIO, LTIO-540 Series; IO-580 Series; IO-720 Wide Cylinder Flange Engines that are equipped with a front crankcase mounted propeller governor. Wide cylinder flange engines are identified by the suffix “A” in the serial number.
TIME OF COMPLIANCE: At next overhaul.
Applicable engines in service that still utilize a P/N MS-9048-111 spring pin to secure the propeller governor idler shaft must be reworked to incorporate a 10-32 set screw. This is accomplished by drilling and tapping the existing spring pinhole as shown in Figure 1. To allow access for peening the set screw in place during reassembly, the area around the hole must also be spot faced, if not already accomplished, as shown in Figure 2.
Engines that are built with the set screw incorporated are assembled with a P/N LW-14021 idler gear shaft. Engines that were built with the P/N MS-9048-111 spring pin incorporated a P/N 77876 idler gear shaft. Replace P/N 77876 idler gear shaft with a P/N LW-14021 idler gear shaft.
Prior to reassembling an engine with damaged th reads in the set screw hole, retap the hole with a 10-32 UNF-3B, P.D. .1697/.1726 inch tap. If necessary, to insure that there are adequate threads in the set screw hole to peen on top of the screw, select a screw that is shorter than the one that was previously removed.
Refer to Table 1 for the applicable set screw part number and length.
NOTE In the following step, a smaller diameter center punch may be used if required to reach the top of a shorter set screw. The tip of a center punch utilized by Lycoming personnel for this purpose is ground to an approximate 50°/60° included angle. See Figure 3.
Assemble the idler gear shaft together with the idler gear and thrust washer and secure the idler gear shaft with the setscrew. Insure that the set screw enters the hole in the idler gear shaft before tightening the screw.
Remove the set screw and apply a light coat of Loctite 290 to the screw. With a clean lint-free cloth, wipe away any excess Loctite 290. Install and tighten the set screw to hold the threaded end of the hex head plug securely in place within the idler gear shaft. Using a center punch with a 3/32-inch diameter shaft, at the top of the tapered point, peen the threads of the hole directly on top of the set screw to prevent the screw from backing out. See Figure 3.
Page 1 of 3 ©2007 by Lycoming “All Rights Reserved”
Service Instruction No. 1343B TABLE 1
DESCRIPTION PART NUMBER Set Screw - 10-32 x .19 inch long AN565B1032H3 Set Screw - 10-32 x .25 inch long AN565B1032H4 Set Screw - 10-32 x .31 inch long AN565B1032H5 Drill. 159 - 165 inch (No. 20) Tap No. 10-32 UNF-3B P.D. : 1697-.1726 inch > Figure 1 6885 inch .6875 If not already accomplished, 3/8 inch dia. spot face, machine square with drilled screw hole to dimension shown.
10° Crankcase Parting .59 inch +0.01 Surface
SECTION A-A Figure 2 Page 2 of 3
Service Instruction No. 1343B Tip has a 50°/60° included angle.
Example of tool in position for peening set screw in place.
Peen threads of hole onto top of set screw to insure screw will not back out.
Figure 3.
Page 3 of 3