TextPartly OCR
Some pages are OCR from a scan. OCR can misread letters and numbers.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '8ff2700c61ea948db2521ef98a5f61c6303d3f2958dee211e8a897a49c4bf520' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '8ff2700c61ea948db2521ef98a5f61c6303d3f2958dee211e8a897a49c4bf520' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
P.O. Box 790490 • San Antonio, Texas 78279–0490 • (210) 824–9421 TO: HOLDERS OF SA227 COMMUTER CATEGORY SERVICE INFORMATION
MANUALS Attached is SA227 Commuter Category Service Bulletin CC7-53-005, Inspection, Extended Inspection, and Repair of Fuselage Upper Forward Corner of Main Cabin Door Cutout , Issued: November 15, 2013.
On aircraft with a bayonet shear pin main cabin door latching mechanism (as opposed to a "click-clack" latching mechanism), the internal door surround doubler, the external skin fuselage skin and, in some cases, the door corner fitting have been found cracked at the fuselage upper forward corner of the main cabin door cutout.
Please insert the attached revised Chapter 53 Index pages.
P.O. Box 790490 • San Antonio, Texas 78279–0490 • (210) 824–9421
Issued: January 18, 1993 Revised: November 15, 2013 CHAPTER 53 INDEX Page 1 of 1 CHAPTER 53 – FUSELAGE
NUMBER DATE TITLE AIRCRAFT EFFECTIVITY SA227 SERIES
COMMUTER CATEGORY 53-001 01-18-93 Cabin Entrance Door Sill SA227-CC, S/N CC784-853 (R)02-25-93 Beef Up. SA227-DC, S/N DC784-853 53-002 09-22-94 Cockpit Floorboard FOD SA227-CC, S/N CC784, 790- (R)06-05-96 Barrier Installation 863 SA227-DC, S/N DC784, 790- 863 53-003 09-03-10 Installation of Form-in-Place All SA227 Commuter Gaskets - Wing-to-Body Category Airplanes Fairings 53-004 10-08-10 Access Panel Installation All SA227 Commuter (R)01-26-11 Category Airplanes 53-005 11-15-13 Inspection, Extended All SA227 Commuter Inspection, and repair of Category Airplanes Fuselage Upper Forward Corner of Main Cabin Door Cutout 53-006 07-27-12 Inspection and/or Replace- All SA227 Commuter (R)05-13-13 ment of the Left Hand and Category Airplanes Right Hand Forward and Aft Wing-to-Body Attach Fittings 53-007 09-26-13 Inspection of F.S. 69.31 All SA227 Commuter (R)11-06-13 Forward Pressure Bulkhead Category Airplanes for Cracks
P.O. Box 790490 • San Antonio, Texas 78279–0490 • (210) 824–9421
Issued: November 15, 2013 CC7-53-005 Page 1 of 20
SERVICE BULLETIN SA227 SERIES
COMMUTER CATEGORY
FUSELAGE Inspection, Extended Inspection, and Repair of Fuselage Upper Forward Corner of the Main Cabin Door Cutout
1. PLANNING INFORMATION A. Effectivity:
Metro 23, SA227-CC, SN CC827, CC829, CC840 to CC844 Metro 23, SA227-DC, SN DC784, DC790 to DC826, DC828, DC830 to DC839, DC845 to DC904 B. Reason:
On aircraft, identified above, with a bayonet shear pin main cabin door latching mechanism (as opposed to a "click-clack" latching mechanism), the internal door surround doubler, the external skin fuselage skin and, in some cases, the door corner fitting have been found cracked at the fuselage upper forward corner of the main cabin door cutout.
C. Description:
Inspect internal or external skin doubler, fuselage skin, and fuselage door frame corner member for cracking. If cracks are found, repair steps are included in this bulletin. If cracks are not found, the repair doubler/tripler can still be added extending the inspection intervals.
D. Compliance:
Mandatory The following initial interval is specified. This interval assumes that the repair members specified by this bulletin have not been installed.
For aircraft with more than 35,000 Total Aircraft Cycles (TAC), inspect within the next 300 cycles or 2 calendar months, whichever occurs first, from the date of this service bulletin.
For aircraft with 20,001 - 35,000 TAC, inspect within the next 600 cycles or 4 calendar months, whichever occurs first, from the date of this service bulletin.
For aircraft with 12,000 - 20,000 TAC, inspect within the next 1,000 cycles or 12 calendar months, whichever occurs first, from the date of this service bulletin.
For aircraft with less than 12,000 TAC, inspect at 12,000 cycles or within the next 1,000 cycles, whichever occurs later.
Issued: November 15, 2013 CC7-53-005 Page 2 of 20
SERVICE BULLETIN SA227 SERIES
COMMUTER CATEGORY Repeat inspection interval for all aircraft is also required.
Inspection Requirements:
Refer to step 2.A. for details.
E. Approval:
FAA Approved for Engineering Design.
F. Manpower:
M7 Aerospace estimates the following manhours per aircraft to accomplish the inspections:
(1) HFEC/LFEC/Detail Visual Inspection - 2.5 hours for threshold inspection.
(2) LFEC with Detail Visual Inspection - 2.0 hours for repeat inspection with inner doubler cracked.
(3) HFEC with Detail Visual Inspection - 1.5 hours for repeat inspection with intact inner doubler
(4) Installation of repair - 48 hours.
This estimate is for direct labor only, accomplished by an experienced crew. Adjust the estimate with operator task hour data if necessary.
G. Material – Cost and Availability:
Contact M7 Aerospace for price and availability. See Step 8. for Material Listing.
Orders need to be placed with M7 Aerospace as there is a lead time on some parts.
H. Tooling – Price and Availability:
The NDT calibration standards (27-02171-001 and 27-02171-021) identified in the Material Listing, Table 4, are the only specialized tools. The standard, P/N 27- 02171-001, is supplied by M7 Aerospace in the bulletin kit or it can be purchased separately from M7 Aerospace. The P/N 27-02171-021 standard will be available from M7 Aerospace at a later date.
Contact M7 Aerospace for price and availability.
I. Weight and Balance:
(1) For inspections only - None.
(2) For installation of the repair kit (P/N 27K24191-001) - 2.5 lbs at F.S. 151. For installation of skin repair per 27K24191-003, 1.0 lbs at F.S. 130. Update the AFM Weight and Balance data.
Issued: November 15, 2013 CC7-53-005 Page 3 of 20
SERVICE BULLETIN SA227 SERIES
COMMUTER CATEGORY J. References:
M7 Engineering Drawing 27K24191, Rev B (or latest FAA approved revision) M7 M-5420 Memorandum M7 Report R1987 - HFEC and LFEC Inspection of Inner Doubler.
M7 Report R2027 - LFEC Inspection of Fuselage Skin.
M7 Aerospace Report No. M07-012-002 (latest FAA approved revision) M7 Aerospace Report No. M07-013-002 (latest FAA approved revision) NOTE: References are for manufacturer’s use only.
K. Other Publications Affected:
ST-UN-M003
2. ACCOMPLISHMENT INSTRUCTIONS This bulletin contains inspections and modifications based upon three scenarios.
Table 1 outlines the basic inspection of this bulletin when complying with the inspection for the first time. Repeat inspections continue if no cracking is found.
Table 2 outlines the new inspections that must be performed once the repair members for the kit repair are installed. Installation of the kit does not remove all of the Table 1 inspections. Several of the Table 1 inspections carry over even when the repair members are installed.
Table 3 offers an option to the operator. It permits the operator to install the repair members as a preventative measure when no cracking is observed after the first threshold inspection.
These members can be installed at any time after the threshold inspection or follow up repeat inspections. In many cases, the addition of the repair members to uncracked structure will result in a new threshold inspection AFTER the aircraft is retired.
Each table identifies figures and bulletin steps detailing the specific inspections to be performed. It is recommended the operator review the entire bulletin for all applicability.
Each table has several specific notes listed below the table as well as the general notes that follow this paragraph below.
NOTES:
The expected aircraft configuration for this service bulletin installation is:
No existing repairs are installed or have been performed at this upper forward door surround corner. If this is not the case and repairs are installed at this location, refer to step 7.
Issued: November 15, 2013 CC7-53-005 Page 4 of 20
SERVICE BULLETIN SA227 SERIES
COMMUTER CATEGORY If any of the remaining three corners of the door cutout have a repair or kit drawing modification installed, this is accommodated within the inspections specified by this bulletin.
See step 2.G.
Definition of Inspections identified in this step:
Detailed Visual Inspection Inspect using an illumination device (such as circular flourescent inspection luminaire) which produces a minimum of 150 fc of light intensity at the part surface and a magnification device (such as a watchmaker's loupe) producing approximately 8X magnification or greater, examine those surface details specified in the inspection requirements noting defects as directed by the inspection requirements.
Close Visual Inspection Inspect using an illumination device (such as circular flourescent inspection luminaire) which produces a minimum of 100 fc of light intensity at the part surface and a magnification device (such as the integral magnifier of the aforementioned inspection luminaire) producing approximately 1.5X magnification or greater, examine all surface details of the part noting any obvious defects.
Sub-Surface Inspection - HFEC/LFEC A subsurface inspection requires calibration. See M7 Aerospace Report R1987 for inspection procedure and calibration standard (27-02171-001). Both are included in the kit. Both High Frequency Eddy Current (HFEC) and Low Frequency Eddy Current (LFEC) are classed as subsurface inspections. Report R2027, which addresses inspection of the repair members once installed, is not ready at the time of this bulletin release. Contact M7 Aerospace for a copy when needed.
A. Perform the Threshold (Initial) and Repeat inspection outlined in Table 1:
(1) when complying with this bulletin for the first time per step 1.D. or
(2) continuing the repeat inspections as no cracks have been found and the operator has elected not to install the repair members per step 6. These inspections still apply if 27K24191-003 skin repair installation is performed.
Issued: November 15, 2013 CC7-53-005 Page 5 of 20
SERVICE BULLETIN SA227 SERIES
COMMUTER CATEGORY NOTES:
<0> Perform these specific service bulletin steps.
<1> Repeat inspection interval assuming no damage or defects found.
TABLE 1
INITIAL INSPECTION
(1) If threshold inspection determines there is an existing repair in the upper forward corner of the door surround, proceed to step 7.
(2) If crack(s)/damage is found during inspection, go to steps 3., 4., and/or 5. as applicable depending on component cracked/damaged. Use step 2.B. and Table 2 for future inspection criteria when repair kit members (27K24191-001) are installed. Use Table 1 inspection intervals if only skin or corner fitting were cracked and replaced and no repair doubler is installed. If only skin and fitting were replaced, it is permissible to install kit per step 6.
(3) If no defect/damage is found, proceed to step 2.H. for aircraft close up or to step
6. when choosing to extend repeat inspection interval.
B. Perform the Threshold and Repeat Inspection outlined in Table 2 when cracks are found following either the threshold or repeat inspection in Table 1. These inspections are based on the 27K24191-001 repair members being installed.
N O I T C E P S N I
N O I T A C O L
N O I T C E P S N I
D O H T E M / E P Y T
P E T S L I A T E D > 0 <
E R U G IFD L O H S E R H T ) S E L C Y C (
T A E P E R ) S E L C Y C ( > 1 < t a r e l b u o d r e n n I d w F r e p p U , r e n r o C , n i k S e g a l e s u F r e n r o C d n a g n i t t i F , l a u s i V l i a t e D
C E F L , C E F H d n a l a n r e t x E ( l a n r e t n I ) s n o i t c e p s n I , . E . 2 , . D . 2 ) 1 ( . F . 2 5 ,40 0 0 , 210 0 0 , 2 f o s r e n r o C r e h t O t u o t u C e g a l e s u F l a u s i V e s o l C d n a l a n r e t x E ( ) l a n r e t n I . G .26 00 0 , 2 1 0 0 0 , 2
Issued: November 15, 2013 CC7-53-005 Page 6 of 20
SERVICE BULLETIN SA227 SERIES
COMMUTER CATEGORY NOTES:
<0> Perform these specific service bulletin steps.
<1> The Table 2 threshold inspection cycles start after the repair doubler in step
3. is installed.
<2> The Table 2 repeat inspection follows the Table 2 threshold inspection once the repair members are installed.
<3> Continuation of Table 1 repeat inspection on the other three corners of the cutout if no cracks were found.
TABLE 2
INSPECTION - CRACKED INNER DOUBLER REPAIRED (P/N 27K24191 KIT INSTALLED) Maintain this inspection criteria for the duration of the aircraft life. Proceed to step
2.H. for close up.
C. Perform Threshold and Repeat Inspection outlined in Table 3 when the 27K24191-001 repair members have been installed as a preventative measure per step 6. These inspections assume no cracks exist and that the fuselage skin Inner Doubler is fully intact (has not been repaired).
N O I T C E P S N I
N O I T A C O L
N O I T C E P S N I
D O H T E M / E P Y T
P E T S L I A T E D > 0 <
E R U G IFD L O H S E R H T ) S E L C Y C (
T A E P E R ) S E L C Y C ( t a n i k S e g a l e s u F d r a w r o F r e p p U r e n r o C
C E F L ) l a n r e t x E ( ) 2 ( . F .25 >1 < 0 0 0 , 51> 2 < 0 0 0 , 2 r i a p e R l a n r e t x E t a r e l b u o D d r a w r o F r e p p U r e n r o C l a u s i V l i a t e D ) l a n r e t x E ( ) 1 ( . D .24 > 1 < 0 0 0 , 51> 2 < 0 0 0 , 2 r i a p e R l a n r e t x E t a r e l b u o D d r a w r o F r e p p U r e n r o C l a u s i V l i a t e D ) l a n r e t n I ( ) 3 ( . D .27 > 1 < 0 0 0 , 03> 2 < 0 0 0 , 6 f o s r e n r o C r e h t O t u o t u C e g a l e s u F l a u s i V e s o l C d n a l a n r e t x E ( ) l a n r e t n I . G .26 A/N> 3 < 0 0 0 , 2
Issued: November 15, 2013 CC7-53-005 Page 7 of 20
SERVICE BULLETIN SA227 SERIES
COMMUTER CATEGORY NOTES:
<0> Perform these specific service bulletin steps.
<1> The Table 3 threshold inspection cycles start after the repair members per step 3. are installed.
<2> The Table 3 repeat inspection follows the Table 3 threshold inspection.
<3> Continuation of Table 1 repeat inspection on the other three corners of the cutout if no cracks were found.
<4> An option is available to perform inspection at 20,000 cycles threshold and 6,000 cycles recurring or 30,000 cycles threshold and 3,000 cycles recurring.
The operator can select which option is better suited to their existing maintenance schedule.
TABLE 3
INSPECTION - INNER DOUBLER NOT CRACKED - PREVENTATIVE P/N 27K24191 KIT INSTALLED This option allows the operator to install the repair kit per step 6. even though no damage/defect was found after the first initial inspection called out in step 1.D. It extends the next inspection for the forward upper corner from a repeat of every 2,000 cycles to a new threshold of 20,000 cycles (see Note <4>). The other three corners still require repeat 2,000 hour inspections per step 2.G. Once the kit is installed, proceed to step 2.H. for close up instructions.
D. Detail Visual Inspection (DVI) (See Figure 4)
(1) External Inspection Prepare the surface for inspection in accordance with SA227 Commuter Category Structural Repair Manual (SRM), Chapter 51-30-07. It is not required to remove surface finish (paint) to perform this inspection. If compounds such
N O I T C E P S N I
N O I T A C O L
N O I T C E P S N I
D O H T E M / E P Y T
P E T S L I A T E D > 0 <
E R U G IFD L O H S E R H T ) S E L C Y C (
T A E P E R ) S E L C Y C ( n i k S r e n n I t a r e l b u o D d r a w r o F r e p p U r e n r o C
C E F H ) l a n r e t x E (. E .25 > 2 < 0 0 0 , 3 > 1 < 0 0 0 , 0 3 R O > 4 < > 2 < 0 0 0 , 6 > 1 < 0 0 0 , 0 2 f o s r e n r o C r e h t O t u o t u C e g a l e s u F l a u s i V e s o l C d n a l a n r e t x E ( ) l a n r e t n I . G .26 A/ N > 3 < 0 0 0 , 2
Issued: November 15, 2013 CC7-53-005 Page 8 of 20
SERVICE BULLETIN SA227 SERIES
COMMUTER CATEGORY as Devcon F or liquid shim are present, which hinder a detail visual inspection, then these compounds must be removed. Care is required not to remove any base material of the surface being cleaned.
Perform a detail visual inspection (as defined in step 2) of the forward upper skin corner fitting, and the visible edge of the inner doubler of the passenger door cutout at the interval specified in Table 1. Perform this same inspection on the corner fitting, edge of fuselage skin, repair doubler and tripler once the 27K24191 repair kit has been installed. Inspect for cracks or pulled/loose fasteners.
(2) Internal Inspection (Kit 27K24191-001 repair members not installed) Gain access to the interior side of the fuselage skin structure immediately adjacent to the upper forward corner of the door cutout. This may require removal of the cabin liner, any interior bulkheads, or cabin furnishings/ monuments. Refer to SA227 Commuter Category Illustrated Parts Catalog (IPC), Chapter 25 for components, and SA227 Commuter Category Maintenance Manual, Chapter 25 for access. Retain all hardware.
Prepare surface for inspection in accordance with SA227 Commuter Category Structural Repair Manual (SRM), Chapter 51-30-07.
Perform a detail visual inspection (as defined in step 2) of the inner skin doubler only, around the fasteners shown in the shaded region of Figure 4, at the interval specified in Table 1. It is not required to remove surface finish (paint/ primer) to perform this inspection. Several fasteners in the actual corner are not visible due to a gusset blocking the view. It is not required to remove the gusset.
(3) Internal Inspection (Kit 27K24191-001 repair members installed) Gain access to the interior side of the fuselage skin structure immediately adjacent to the upper forward corner of the door cutout. This may require removal of the cabin liner, any interior bulkheads, or cabin furnishings/ monuments. Refer to SA227 Commuter Category Illustrated Parts Catalog (IPC), Chapter 25 for components, and SA227 Commuter Category Maintenance Manual, Chapter 25 for access. Retain all hardware as required.
Prepare the surface for inspection in accordance with SA227 Commuter Category Structural Repair Manual (SRM), chapter 51-30-07.
Perform a Detailed Visual Inspection (DVI), as defined in step 2, of the fuselage skin surface immediately at the peripheral row of fasteners attaching the external repair doubler to the structure underneath (see Figure 7), at the interval specified in Table 2. It is not required to remove any surface finish (paint/primer) to perform this inspection. Several fasteners in the actual corner