On this page
Text · 16Partly OCR
Some pages are OCR from a scan. OCR can misread letters and numbers. © Mitsubishi. Filed by the FAA in regulations.gov docket FAA-2016-9139, the docket of a proposed AD (Federal Register 2016-22182, 2019-03397). Not covered by OpenAirDocs’ CC0 dedication.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '4f8fcd96a2567beaa2794f6fd287a2c2bca0e41687b2675b05bc73878ffa469e' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '4f8fcd96a2567beaa2794f6fd287a2c2bca0e41687b2675b05bc73878ffa469e' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
M U - 2
S E R V I C E B U L L E T I N MITSUBISHI HEAVY INDUSTRIES, LTD.
NAGOYA AEROSPACE SYSTEMS WORKS 10, OYE-CHO, MINATO-KU, NAGOYA, JAPAN
Page 1 of 14 No. 107/57-005 DATE: May 3, 2016 Subject: Wing Spacer Plate – Inspection and Replacement of Effectivity: MU-2B-25/-26/-26A/-40: S/N 313SA, 321SA, 348SA through 459SA MU-2B-36A/-60: S/N 661SA, 697SA through 1569SA Purpose: To ensure the continued airworthiness of the wing structures , conduct a one-time fluorescent penetrant inspection for the wing spacer plates and replace them, if necessary.
Background: As part of aging aircraft pr ogram, one -piece and three -piece main wings were subject of detailed teardown inspections, and cracks were found in the wing spacer plate s attached to the forward lower spar at W.STA580. The cracks resulted from fatigue to be caused by flight load.
Compliance: Mandatory Approval: Engineering aspects of this Service Bulletin are FAA Approved Time of Compliance: a) For aircraft with flight time 7,500 hours or over
- within 200 hours, or 12 months whichever comes first after receipt of this Service Bulletin.
b) For aircraft with flight time less than 7,500 hours
- to be include in 7,500 hours inspection.
Responsible Agency of Compliance:
MU-2 Owners/Operators Disposition of Removed Parts:
Scrap Spare Parts Affected: Replacement Kit (P/N 035A-900021-101/-102) Required Man Hours: Inspection ~approximately 4 man hours for each side Replacement ~approximately 40 man hour s for each side excluding preparation and restoration Special Tools Required: None Weight and Balance Change:
Negligible Flight Manual Revision: None
MU-2 Service Bulletin No. 107/57-005 DATE: May 3, 2016
Page 2 of 14
INSTRUCTIONS Refer to applicable Maintenance Manual, Illustrated Parts Catalog and Structural Repair Manual to comply with this Service Bulletin.
1. INSPECTION PROCEDURE
NOTE Identify and store all removed parts and attaching hardware.
If it is necessary to remove further parts for access, inspection and replacement, you can remove those parts beyond following process. If you can access, inspect and replace without removing the parts instructed in following process, it is not necessary to remove the parts.
1.1 PREPARATION
(1) Electrically ground the aircraft.
(2) Remove the wing center lower fillet and the inner wing leading edge in accordance with applicable Maintenance Manual.
(3) Remove sealant and primer from the inspection area between the spacer plate and the skin with a nonmetallic scraper. See Figure 1 and 2.
(4) Clean and expose the inspection surface.
1.2 INSPECTION
(1) Conduct a fluorescent penetrant inspection to the inspection area shown in Figure 1 and 2 on both left and right sides of wing in accordance with applicable Maintenance Manual.
NOTE Personnel performing fluorescent penetrant inspection must be qualified and certified as a Level II or higher based on the requirements of National Aerospace Standard NAS410 or equivalent standard.
(a) When a crack of 0.6 inches or greater is found Replace the discrepant spacer plate with a new improved spacer plate (P/N 017A-11102-13/-14) and scrap the discrepant spacer plate. Replacement procedure is instructed in Section 2.
(b) When a crack of less than 0.6 inches is found It is allowed to monitor the crack growth by repetitive inspection at the interval of 600 hours. However, the spacer plate must be replaced when the crack length grows beyond 0.6 inches.
1.3 RESTORATION
(1) Clean up the inspection area and apply Alodine and zinc chromate primer.
(2) Apply sealant to fill the gaps between the spacer plates and the skin in accordance with applicable Maintenance Manual.
(3) Restore the inner leading edge.
(4) Restore the wing center lower fillet.
MU-2 Service Bulletin No. 107/57-005 DATE: May 3, 2016
Page 3 of 14
2. REPLACEMENT PROCEDURE
NOTE Replacement Kit may be purchased from Mitsubishi Heavy Industries America, Inc. (MHIA) through Mitsubishi MU-2 Authorized Service Center Network.
Replacement of the spacer plate should be conducted in accordance with the installation drawing contained in Replacement Kit.
2.1 PREPARATION
NOTE Removal of the engines, each system, the wing and the other attaching hardware should be accomplished in accordance with applicable Maintenance Manual.
(1) Electrically ground the aircraft.
(2) Drain fuel and purge fuel tanks.
(3) Remove all wing-fuselage fillets, the fuel system, the engines, the air conditioning and wing de-icer system, the electrical and instrument system, and the flight control system from the wing.
(4) Remove the wing and set appropriate support.
(5) Remove the inner wing leading edge.
(6) Remove the shut off valves.
(7) Remove the fuel tank access doors.
2.2 REPLACEMENT
(1) Remove sealant inside the integral tank with a nonmetallic scraper.
(2) Remove the outer wing-fuselage fitting and the inner support fitting. If shims are installed, record thickness and location, and store.
(3) Drill out and cut off the fasteners on and around the spacer plate.
NOTE Several tack rivets and a nut plate are hidden under the skin and sealant as shown in Figure 4. Be careful not to damage adjacent structural components when removing the spacer plate.
(4) Peel up the skin and slide out the spacer plate from the wing.
(5) Remove remaining sealant inside of the integral tank. Clean up the integral tank and the outer wing-fuselage fitting and the inner support fitting.
(6) Duplicate all fastener holes to a new spacer plate from the removed spacer plate. Do not apply countersink to the holes for tack rivets and nut plate installing rivets.
(7) Temporary locate the new spacer plate and drill out the holes for tack rivets to the skin by picking up the existing tack rivet holes on spar through the new spacer plate.
(8) Drill out the holes for nut plate installing rivets to the skin by picking up the existing holes on spar through the new spacer plate.
(9) Remove the new spacer plate and clean up.
MU-2 Service Bulletin No. 107/57-005 DATE: May 3, 2016
Page 4 of 14
(10) Apply sealant to the new spacer plate and the existing structure where sealant should be applied before fastening in accordance with the installation drawing (refer to Figure 5), and locate the spacer plate.
(11) Install all fasteners to the spacer plate, a nut plate and tack rivets in accordance with the installation drawing (refer to Figure 3 and 4).
(12) Adjust the gap between the outer wing-fuselage fitting and the spacer plate with laminated shim within 0.005 inches (refer to Figure 3).
(13) Touch up the laminated shim with zinc chromate primer.
(14) Install the outer wing-fuselage fittings and the inner support fitting.
(15) Clean up inside and outside of the integral tank.
(16) Apply integral tank sealant and dry in accordance with applicable Maintenance Manual and the installation drawing (refer to Figure 5).
(17) Apply sealant to fill the gaps between the spacer plate and the skin shown by the hatched area in Figure 2 in accordance with applicable Maintenance Manual.
2.3 FUEL LEAKAGE CHECK
(1) Conduct the integral tank leakage test in accordance with applicable Maintenance Manual.
(2) If fuel leakage is found, rework sealing.
2.4 RESTORATION
NOTE Restoration of the disrupted systems, including rigging and operational tests, should be accomplished in accordance with applicable Maintenance Manual.
(1) Install the fuel tank access doors.
(2) Install the fuel shut off valves.
(3) Install the inner wing leading edge.
(4) Install the wing.
(5) Install the flight control system, the electrical and instrument system, the air conditioning and wing de-icer system, the engines, the fuel system and all wing-fuselage fillets.
(6) Refuel full and check no leakage.
3. RECURRING INSPECTION
(1) If no crack is found during the inspection, repeat the inspection in accordance with the revised Maintenance Requirement Manual at the interval of 2,000 hours.
(2) If the crack of less than 0.6 inches is found, repeat the inspection at the interval of 600 hours for crack growth monitoring in accordance with this Service Bulletine. When the crack length exceeds 0.6 inches, replace the cracked spacer plate with a new improved spacer plate.
(3) Once the spacer plate is replaced with a new improved spacer plate (P/N 017A-11102-13/-14), recurring (repetitive) inspection is not required.
MU-2 Service Bulletin No. 107/57-005 DATE: May 3, 2016
Page 5 of 14
4. LOGBOOK ENTRY Upon completion of this Service Bulletin, make an appropriate maintenance entry in the logbook similar to “Service Bulletin No. 107/57-005 complied with on (date) by (name), number/stamp.”
5. COMPLETION Complete the enclosed compliance card and mail back to Mitsubishi Heavy Industries America, Inc. in care of Turbine Aircraft Services, Inc.
Turbine Aircraft Services, Inc.
4550 Jimmy Doolittle Drive Addison, Texas 75001
Attention: Manager, Publications Phone: (972) 248-3108 X 209 Fax: (972) 248-3321
MU-2 Service Bulletin No. 107/57-005 DATE: May 3, 2016
Page 6 of 14 Parts and Material Required The following parts and material are required to comply with this Service Bulletin.
Replacement Kit may be purchased from Mitsubishi Heavy Industries America, Inc. (MHIA) through Mitsubishi MU-2 Authorized Service Center Network.
All the parts and material except for Replacement Kit may be procured locally.
PART NUMBER DESCRIPTION
QTY/SHIP
REMARKS LH (-101) RH (-102) KIT number 035A-900021-101 to replace LH spacer plate KIT number 035A-900021-102 to replace RH spacer plate 035A-11076 DRAWING 1 1 017A-11102-13 SPACER PLATE 1 017A-11102-14 SPACER PLATE 1 017A-11102-15 LAMINATED SHIM 1 1 800-0115-10 LOCK-O-SEAL 14 14 change PN of 800-015-10 NAS1149D0363H WASHER 14 14 NAS1149D0316H WASHER 4 4 MS20002C7 WASHER 2 2 MS20002-7 WASHER 2 2 NAS679A3W NUT 16 16 H20-7 NUT 2 2 NAS1473A3 DOME NUT 1 1 MS20426AD3-10 RIVET 4 4 not contained in the KIT MS20426AD4-5 RIVET 6 6 not contained in the KIT MS20426AD5-12 RIVET 9 9 not contained in the KIT MS20426AD5-7 RIVET 3 3 not contained in the KIT MS20470AD3-10 RIVET 2 2 not contained in the KIT MS20470AD3-11 RIVET 2 2 not contained in the KIT MS20470AD3-7 RIVET 1 1 not contained in the KIT MS20470AD4-5 RIVET 15 15 not contained in the KIT MS20470AD5-12 RIVET 11 11 not contained in the KIT MS20470AD5-13 RIVET 6 6 not contained in the KIT MS20470AD5-7 RIVET 9 9 not contained in the KIT MS20470AD5-9 RIVET 6 6 not contained in the KIT NAS1097AD4-9 RIVET 16 16 not contained in the KIT AMS-S-8802 Class A or equivalent SEALANT AR AR not contained in the KIT AMS-S-8802 Class B or equivalent SEALANT AR AR not contained in the KIT TT-P-1757 or equivalent PRIMER AR AR not contained in the KIT
MU-2 Service Bulletin No. 107/57-005 DATE: May 3, 2016
Page 7 of 14
Figure 1: LOCATION OF SPACER PLATE INSPECTION (Typical, LH side shown, RH side opposite.)
OUT B/D (LH) FWD LKG UP Spacer plate
OUT B/D (LH) FWD LWR Web Outer wing-fuselage fitting Spar Skin Skin Sealant Crack Spacer plate Inspection area Crack
MU-2 Service Bulletin No. 107/57-005 DATE: May 3, 2016
Page 8 of 14
Figure 2: DETAILED INSPECTION AREA OF SPACER PLATE (Typical, LH side shown, RH side opposite.)
Skin Skin Skin Spacer plate Spacer plate Outer wing-fuselage fitting Spar Spar Crack Hatched area is filled with sealant A A
SECTION A-A Crack Inspection area FWD
OUT B/D (LH) LKG UP UPR
OUT B/D (LH) W.S.
580 W.S.
MU-2 Service Bulletin No. 107/57-005 DATE: May 3, 2016
FRONT SPAR REF PLANE
FRONT SPAR - LOWER (REF)
TACK RIVET (REF) 1 MS20426AD3-10 BRACKET 2 REOD MS20426AD5-12 9 REOD DOME NUT MS20426AD4-5 6 REOD DRILL #11 (4.85)
• NAS1473A3 1 REOD (REMOVE) 14633H-020 9 MS20426AD3-10 2 REOD MS20426AD5-7 3 REQD € MS20470AD5-12 2 REOD MS20470AD5-9 6 REOD ®
TACK RIVET ® MS20470AD3-11 2 REQD
RIB ASSY (REF) 6 MS20470AD5-13
TACK RIVET
• MS20470AD3-7 1 REOD @
STIFFENER PANEL (REF) NAS 1097AD4-9 16 REOD / C'SINK ON SPACER PLATE AND SPAR CHORD. NEAR SIDE FOR MS20470AD5-7 9 REQD MANUFACUTURED HEAD.
DO NOT INSTALL RIVETS TO LAMINATED SHIM.
Spacer plate . 4375 1 0020 017A-11102-13 1 REOD (LH) 017A-11102-14 1 REOD (RH) 17A-11102-5 1 REQD (LH)) (REMOVE 17A-11102-6 1 REOD (RH)
TACK RIVET ® MS20470AD3-10 LOWER SKIN (REF) 2 REQD 1S20470AD4-5 15 REQD MS20470AD5 29 REOD
OUTBOARD → FWD J
LH SHOWN RH OPPOSITE 6 : MS20426AD5 : UP TO S/N 250 S/N 501 TO 575 VIEW LOOKING UP MS20470AD5 : S/N 251 TO 466 S/N 576 & UP 3 : PEEL 003" LAMINATING AS REQUIRED TO FILL GAP WITHIN ,005i PRIOR TO BOLT INSTALLATION.
APPLY ZINC CHROMATE PRIMER TO LAMINATED SHIM BEFORE INSTALLING.
2 : INSTALL UNDER NUT.
1 : INSTALL UndeR BOLT HEAD.
NOTES Figure 3: INSTALLATION OF NEW SPACER PLATE (1/2) (Typical, LH side shown, RH side opposite.)
Page 9 of 14
MU-2 Service Bulletin No. 107/57-005 DATE: May 3, 2016 NAS1203-13 2 REQD (REUSE) NAS679A3W 2 REQD (REPLACE WITH NEW ONE) 800-0115-10 2 REQD (BETWEEN FITTING AND WASHER) NAS1149D0316H 4 REQD AN960D1OL 800-015-10 4 REOD} ‹REMOVE › FRONT SPAR REF PLANE 017A-11002-13 AS REQD (REUSE) Shim
UPR SKIN (REF) → Inner support fitting 017A-11952-1 017A-11952-2 1 REQD (RH) | (REUSE) 1 REQD (LH) NAS1103-13 10 REQD NAS1103-16 2 REQD (REUSE) NAS1103-20 2 REQD NAS679A3W 14 REQD (REPLACE WITH NEW ONE) 1 800-0115-10 14 REQD NAS1149D0363H 14 REQU 800-015-10 14 REOD | (REMOVE › AN960D10 14 REQD (NEAR SIDE FOR BOLT HEAD) REAM . 4375 $00020 (11.11318.050) MS20007-24 2 REQD (REUSE) H20-7 2 REQD MS20002C7 2 REQD (REPLACE WITH NEW ONE) MS20002-7 2 REQD (NEAR SIDE FOR BOLT HEAD) Spacer plate 017A-11102-13/-14 (REF)
DOUBLER (REF)
STIFFENER PANEL (REF)
LWR SKIN (REF) 017A-11102-15 1 REQD Laminated shim 3 : PEEL 003" LAMINATING AS REQUIRED TO FILL GAP WITHIN .005" PRIOR TO BOLT INSTALLATION.
APPLY ZINC CHROMATE PRIMER TO
LAMINATED SHIM BEFORE INSTALLING @ : INSTALL UNDER NUT.
1 : INSTALL UNDER BOLT HEAD.
(REUSE) - FWD 017A-11951-1 1 REQD (LH) NOTES 017A-11951-2 1 REQD (RH) Outer wing-fuselage fitting SECT A-A Figure 3: INSTALLATION OF NEW SPACER PLATE (2/2) (Typical, LH side shown, RH side opposite.)
Page 10 of 14
MU-2 Service Bulletin No. 107/57-005 DATE: May 3, 2016 9 Nut plate • Tack rivet 1 Tack rivet Note: Tack rivets and a nut plate are installed under the skin originally.
7 : INSTALL RIVET MS20426AD3 AS SHOWN.
MS20426AD3 MS20426AD3
C'SINK ON C'SINK ON SKIN
SPACER PLATE (REF) FRONT (REF)
SPACER PLATE SPAR SPACER PLATE (SHOULD BE REMOVED) (REF) (NEW PART) (BEFORE) (AFTER) 8 : INSTALL RIVET MS20470AD3 AS SHOWN.
MS20426AD3 MS20470AD3
C'SINK ON
SPACER PLATE (REF) FRONT (REF)
SPACER PLATE SPAR SPACER PLATE (SHOULD BE REMOVED) (REF) (NEW PART) (BEFORE ) ( AFTER) ›: INSTALL RIVET MS20426AD3 AND DOME NUT AS SHOWN.
MS20426AD3 SKIN MS20426AD3
C'SINK ON C'SINK ON SKIN
SPACER PLATE , (REF) FRONT (REF)
SPACER PLATE SPAR SPACER PLATE (SHOULD BE REMOVED) (REF) (NEW PART)
DOME NUT (BEFORE) (REF) ( AFTER) Figure 4: INSTALLATION OF TACK RIVET AND NUT PLATE (Typical, LH side shown, RH side opposite.)
Page 11 of 14
MU-2 Service Bulletin No. 107/57-005 DATE: May 3, 2016
FRONT SPAR REF PLANE
BRACKET (REF)
RIB ASSY (REF) Vo
STIFFENER PANEL (REF) (REF) 017A-11951-1/-
LWR SKIN (REF) 017A-11102-13/-14 (REF) 017A-11102-15 (REF)
OUTBOARD → FWD -
SEALING _H SHOWN
RH OPPOSITE
VIEW LOOKING UP Figure 5: SEALING INSTRUCTION (1/3) (Typical, LH side shown, RH side opposite.)
Page 12 of 14