Copy · Ontic SBCC7-27-038R3 · 13 pages

© Ontic. Filed by the FAA in regulations.gov docket FAA-2026-2723; AD 2026-21-13 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Text

From the PDF’s text layer: layout, tables and figures are lost. The PDF is the document.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '878d25c26e2eb602c673c8e1c6c5d44b4625ab65561a26289aad3d97c130dde2'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

1176 TELECOM DRIVE • CREEDMOOR, NC 27522 • (919) 956-4300 KŶƟĐŶŐŝŶĞĞƌŝŶŐĂŶĚDĂŶƵĨĂĐƚƵƌŝŶŐ͕/ŶĐ TO: HOLDERS OF SA227 COMMUTER CATEGORY SERIES SERVICE INFORMATION

MANUALS Attached is SA227 Commuter Category Series Service Bulletin CC7-27-038R3, INSPECTION OF DL5040M5, DL5040M6, and DL5040M8 PITCH TRIM ACTUATORS, Issued: July 29, 2024; Revised: January 27, 2026.

This service bulletin provides instructions to perform a time travel check and inspect for sealant integrity and corrosion to the DLM5040M5, DLM5040M6, and DLM5040M8 pitch trim actuators. The pitch trim actuators must be replaced if corrosion or other damage is found, if actuator travel speeds are not met, or if time in service without appropriate seals is exceeded.

This revision updates actuator time check information as well as manpower estimates.

Please insert the attached Service Bulletin and replace the Chapter 27 Index pages.

Issued: July 29, 2024 Revised: January 27, 2026 CC7-27-038R3 Page 1 of 10

SERVICE BULLETIN KŶƟĐŶŐŝŶĞĞƌŝŶŐĂŶĚDĂŶƵĨĂĐƚƵƌŝŶŐ͕/ŶĐ SA227 SERIES

COMMUTER CATEGORY

FLIGHT CONTROLS INSPECTION OF DL5040M5, DL5040M6, and DL5040M8 PITCH TRIM ACTUATORS

1. PLANNING INFORMATION A. Eff ectivity:

All SA227 Commuter Category Airplanes equipped with DL5040M5, DL5040M6, and DL5040M8 Pitch Trim Actuators.

B. Reason:

Service experience has indicated susceptibility of the internal and external components of the DL5040M5, DL5040M6, and DL5040M8 Pitch Trim Actuators to corrosion. This Service Bulletin specifi es inspections and functional checks of the Pitch Trim Actuators to ensure continued seal integrity on the actuators and absence of corrosion.

This revision to the service bulletin clari fi es the repetitive time checks for the various diff erent actuators and updates the manpower requirements.

C. Description:

Perform an initial and repetitive inspection / check of the DL5040M5, DL5040M6, and DL5040M8 Pitch Trim Actuators to check for corrosion and check actuator travel times. The tasks specifi ed in this Service Bulletin are to be completed supplemental to the inspections specifi ed in Service Letter CC7-SL-028 and Airworthiness Directive 2007-16-03. Compliance with the actuator travel time checks in Service Letter CC7-SL-028 for the DL5040M8 actuator can be used to satisfy the travel time check requirements in this Service Bulletin for the DL5040M8 actuator, as long as the inspection threshold and interval calendar time requirements are met. For any confl ict between this Service Bulletin and the requirements of AD 2007-16-03, the AD shall take precedence.

D. Compliance:

Mandatory. The initial action compliance time remains unchanged; refer to the original service bulletin for the date. Compliance time for repetitive action is de fi ned in the current revision of the service bulletin.

NOTE:

Actions in this Service Bulletin are specifi ed in terms of calendar time and fl ight hours.

For actions specifi ed in terms of calendar time, time in service commences on the date that a new or overhauled actuator is installed on an airplane and is continuous thereafter until overhauled as specifi ed in this Service Bulletin, whether it remains on the airplane or not.

For all airplanes, perform the following actions at the times specifi ed; in the initial action column and the repetitive action column in Table 1 of this service bulletin.

Issued: July 29, 2024 Revised: January 27, 2026 CC7-27-038R3 Page 2 of 10

SERVICE BULLETIN SA227 SERIES

COMMUTER CATEGORY KŶƟĐŶŐŝŶĞĞƌŝŶŐĂŶĚDĂŶƵĨĂĐƚƵƌŝŶŐ͕/ŶĐ

FLIGHT CONTROLS Condition Initial Action Repetitive Action I. All DL5040M5, DL5040M6, and DL5040M8 actuator assemblies.

Within the next 1,000 fl ight hours or 6 calendar months from the date of this Service Bulletin, whichever is sooner, determine if the actuator rod ends have been sealed as shown in Figure 3, Locations 1 and 2, of this Service Bulletin since the actuator was initially put into service. Perform the actions as specifi ed in Conditions II, III or IV below.

II. For actuators whose rod ends have been sealed as shown in Figure 3, Locations 1 and 2, since put into service.

No additional initial action required.

A.

B.

For DL5040M5 actuators, every 250 fl ight hours or 6 months whichever occurs sooner and for DL5040M6 and DL5040M8 actuators, every 300 fl ight hours or 6 months, whichever occurs sooner check the pitch trim actuators in accordance with Step 2.A, and For all actuators, every 1,000 fl ight hours or every 12 calendar months, whichever occurs sooner, inspect and seal the actuator per Step 2.B.

III. For actuators whose rod ends have not been sealed as shown in Figure 3, Locations 1 and 2, since put into service and have less than 1,000 fl ight hours or 6 months calendar time in service, whichever is less.

Prior to incurring 1,000 fl ight hours or 6 months calendar time in service on the actuator, whichever is less, inspect and seal the actuator per Step 2.B.

A.

B.

For DL5040M5 actuators, every 250 fl ight hours or 6 months whichever occurs sooner and for DL5040M6 and DL5040M8 actuators, every 300 fl ight hours or 6 months, whichever occurs sooner check the pitch trim actuators in accordance with Step 2.A, and For all actuators, every 1,000 fl ight hours or every 12 calendar months, whichever occurs sooner, inspect and seal the actuator per Step 2.B.

IV. For actuators whose rod ends have not been sealed as shown in Figure 3, Locations 1 and 2, since put into service and have 1,000 fl ight hours or 6 months calendar time in service, whichever is less.

Replace the actuator with a new or overhauled actuator and install and seal the actuator per Step

2.B.8).

A.

B.

For DL5040M5 actuators, every 250 fl ight hours or 6 months whichever occurs sooner and for DL5040M6 and DL5040M8 actuators, every 300 fl ight hours or 6 months, whichever occurs sooner check the pitch trim actuators in accordance with Step 2.A, and For all actuators, every 1,000 fl ight hours or every 12 calendar months, whichever occurs sooner, inspect and seal the actuator per Step 2.B.

Table 1: Compliance Requirements

Issued: July 29, 2024 Revised: January 27, 2026 CC7-27-038R3 Page 3 of 10

SERVICE BULLETIN KŶƟĐŶŐŝŶĞĞƌŝŶŐĂŶĚDĂŶƵĨĂĐƚƵƌŝŶŐ͕/ŶĐ SA227 SERIES

COMMUTER CATEGORY

FLIGHT CONTROLS NOTE:

Acceptable replacement pitch trim actuators part numbers are specifi ed in Airworthiness Directive AD 2007-16-03. The term overhaul as applied in this Service Bulletin is an FAA approved procedure that de fi nes the disassembly, inspection, troubleshooting, replacement of defective components, servicing, reassembly and functional testing of the pitch trim actuators. AD 2007-16-03 specifi es the intervals for repetitively replacing the actuator with a new or overhauled actuator.

The following is an FAA-approved facility performing overhaul and repairs of Simmonds- Precision Actuators. There may be other FAA approved facilities.

Contact Information:

World Class Accessory, Inc.

1130 Dividend Court Peachtree City, GA 30269 Phone: (770) 631-2470 Fax: (770) 631-0664 Email: repairs@worldclassaccessory.com Website: www.worldclassaccessory.com E. Approval:

The Engineering aspects were approved with the initial revision of this service bulletin.

This revision only refers to previously FAA approved data. No additional FAA approvals are required.

F. Manpower:

Step 2.A and Step 2.B each require an estimated 3 direct man-hours by an experienced crew. If fi llet sealant removal and reapplication is necessary, Step 2.B's estimate increases to 5 man-hours. Adjust estimates with operator task-hour data as needed.

G. Material - Cost and Availability:

Contact the Ontic Sales Team for cost and availability: metroparts@ontic.com.

H. Tooling-Price and Availability:

Refer to the SA227 Commuter Category Series Maintenance Manual for required tooling to conduct actuators free play and time / racheting checks.

Issued: July 29, 2024 Revised: January 27, 2026 CC7-27-038R3 Page 4 of 10

SERVICE BULLETIN SA227 SERIES

COMMUTER CATEGORY KŶƟĐŶŐŝŶĞĞƌŝŶŐĂŶĚDĂŶƵĨĂĐƚƵƌŝŶŐ͕/ŶĐ

FLIGHT CONTROLS I. Weight and Balance:

Negligible NOTE : It is recommended the aircraft operating weight be re-established after incorporating 20 service bulletins classi fi ed as having negligible impact on aircraft weight and balance. This recommendation is derived from data provided in FAA Advisory Circular 120-27.

J. References:

• SA227 Commuter Category Structural Repair Manual, Chapter 51-30-02 and 51-

30-03.

• SA227 Commuter Category Maintenance Manual, Chapter 27-40-10.

• SA227 Commuter Category Phase Inspection Manual, Form 608, Detailed Inspection.

• SA227 Commuter Category Letter Check Inspection Manual, Letter Check D.

• Ontic Drawings 27-19008, 27-43027, 32-8203.

• Ontic Report R1529.

• Ontic Technical Memorandums M-2225A, M-2231, M-2320, and M-2329.

NOTE: References are for manufacturers’ use only.

K. Other Publications Aff ected: None.

2. ACCOMPLISHMENT INSTRUCTIONS A.

Pitch Trim Actuator Time Travel Check

1) Record pitch trim actuator part number, serial number, date and total time in service for the actuator since last overhaul.

2) Clear tail of all personnel and equipment.

3) Connect external electrical power to aircraft.

(Refer to SA227 Commuter Category AMM, 24-40-00).

4) Ensure LH and RH essential bus voltages for DL5040M5 (Mod 1 and 2), DL5040M6, and DL5040M8 actuators are 29.0 + 0.0 /-0.5 VDC.

NOTE: Prior to performing actuator travel time check, verify proper adjustment of horizontal stabilizer electrical stops (limit switches) IAW SA227 Commuter Category AMM, Section 27-40-10, Step 4. C. Adjustment - Electrical/Mechanical Stops in this section.

Issued: July 29, 2024 Revised: January 27, 2026 CC7-27-038R3 Page 5 of 10

SERVICE BULLETIN KŶƟĐŶŐŝŶĞĞƌŝŶŐĂŶĚDĂŶƵĨĂĐƚƵƌŝŶŐ͕/ŶĐ SA227 SERIES

COMMUTER CATEGORY

FLIGHT CONTROLS

5) Place TRIM SELECT switch on COPILOT.

6) Using copilot control wheel trim switch, run horizontal stabilizer to full aircraft nose up position (leading edge of stabilizer will be full down).

NOTE: Travel time begins at the fi rst trim in motion beep and ends at the last beep.

7) Using copilot control wheel trim switch, run stabilizer to extreme aircraft NOSE DOWN position (leading edge of stabilizer will be full up) and record time of travel. Verify travel time is:

a. 18 to 25 seconds for P/N DL5040M5, Mod 1

b. 18 to 27 seconds for P/N DL5040M5, Mod 2

c. 18 to 27 seconds for P/N DL5040M6

d. 25 to 30 seconds for P/N DL5040M8

8) Using copilot control wheel trim switch, run stabilizer to extreme aircraft NOSE UP position (leading edge of stabilizer will be full down) and record time of travel. Verify travel time is:

a. 18 to 25 seconds for P/N DL5040M5, Mod 1

b. 18 to 27 seconds for P/N DL5040M5, Mod 2

c. 18 to 27 seconds for P/N DL5040M6

d. 25 to 30 seconds for P/N DL5040M8

9) Using pilot control wheel trim switch, repeat steps (6) through (8).

10) Maximum allowable split between travel time from full up to full down and from full down to full up may not exceed four seconds on either side.

11) If travel time is not within specifi ed limits:

a. Disconnect actuator rod of faster side (pilot or copilot).

b. Check stabilizer travel time of the remaining connected actuator rod.

i. If travel time is now within limits, the actuator installation is suspect. Check actuator installation for misalignment and/or check horizontal stabilizer for binding.

c. Disconnect other actuator rod end and check time required for each actuator rod to extend and retract fully.

i. If actuator rods meet travel time criteria, check actuator installation for misalignment.

ii. If either actuator rod does not meet travel time criteria, replace the actuator.

Issued: July 29, 2024 Revised: January 27, 2026 CC7-27-038R3 Page 6 of 10

SERVICE BULLETIN SA227 SERIES

COMMUTER CATEGORY KŶƟĐŶŐŝŶĞĞƌŝŶŐĂŶĚDĂŶƵĨĂĐƚƵƌŝŶŐ͕/ŶĐ

FLIGHT CONTROLS

12) Disconnect external electrical power from aircraft.

(Refer to SA227 Commuter Category AMM 24-40-00).

13) Proceed to Step 2.C.

B. Inspection of Pitch Trim Actuators

1) Record pitch trim actuator part number, serial number, date and total time in service for the actuator since last overhaul.

2) Lower horizontal stabilizer to the full leading edge down position.

3) Using good lighting (100 FC minimum) and using inspection mirrors as required, perform a general visual inspection of the actuator checking for signs of corrosion or other damage.

4) Using good lighting (100 FC minimum) and inspection mirrors, perform a detailed visual inspection of the juncture of the actuator casing with the base of the actuator (see Figure 2). Check for signs of moisture / fl uid leaking from inside the actuator, signs of corrosion or other damage. Indications of any of these requires replacement of actuator with a new or overhauled actuator.

5) There are two weep holes on the aft, lower surface of the actuator casing.

Inspect the two weep holes to ensure that they are clear of foreign matter or debris.

6) Using good lighting (100 FC minimum), perform a detailed visual inspection of the actuator two upper rod ends, jam nuts, locking washers, lock wire and moving tubes checking (see Figure 3) for signs of corrosion or other damage. If there are indications of corrosion or other damage, replace with a new or overhauled actuator.

7) For each ram of the actuator, check the integrity of the sealant shown in Figure 3. If there is no sealant present, then proceed to Step 2.B.8) or if integrity of the sealant is compromised remove the defective sealant and proceed to Step 2.B.8). If the integrity of the seal is acceptable, proceed to Step 2.C.

8) If no sealant is present or existing sealant is cracked/missing or compromised, as shown in Figure 3, then for each ram of the actuator, clean the area and/or remove the old sealant around the threads of the rod end, the jam nut, the lock washer and the insert per SRM 51-30-02 and apply sealant per SRM 51-30-03 to the exposed threads of the rod end, in the rod end keyway, to the top and bottom of the lock washer and encapsulate the nut (see Figure 3). When applying sealant between the lock washer and the

Issued: July 29, 2024 Revised: January 27, 2026 CC7-27-038R3 Page 7 of 10

SERVICE BULLETIN KŶƟĐŶŐŝŶĞĞƌŝŶŐĂŶĚDĂŶƵĨĂĐƚƵƌŝŶŐ͕/ŶĐ SA227 SERIES

COMMUTER CATEGORY

FLIGHT CONTROLS moving tube, protect the circumference of the moving tube from sealant and fi llet seal between the top of the moving tube and the bottom of the lock washer as shown in Figure 3. Proceed to Step 2.C.

C. Return to Service

1) Perform operational check of all systems a ff ected by this Service Bulletin in accordance with applicable sections of the SA227 Commuter Category Maintenance Manual (MM).

a. For each actuator returned from overhaul or new, once installed in the aircraft, and rigging/adjustment is complete, apply sealant to each ram rod end per Step 2.B.8).

2) Reinstall all panels removed using retained hardware. Replace any damaged hardware with new hardware.

3) Complete aircraft records in accordance with 14 CFR 43.9.

4) Complete and return service bulletin Compliance Form to Ontic Engineering and Manufacturing Technical Support Department.

Email: Metroliner@Ontic.com.

3. MATERIAL LISTING Location / Item Part Number Alternate P/N Quantity At Horizontal Pitch Trim Actuator:

Pitch Trim Actuator DL5040M5 - 1 Pitch Trim Actuator DL5040M6 - 1 Pitch Trim Actuator DL5040M8 - 1 NOTE: Contact an FAA authorized facility for overhaul of actuator.

Issued: July 29, 2024 Revised: January 27, 2026 CC7-27-038R3 Page 8 of 10

SERVICE BULLETIN SA227 SERIES

COMMUTER CATEGORY KŶƟĐŶŐŝŶĞĞƌŝŶŐĂŶĚDĂŶƵĨĂĐƚƵƌŝŶŐ͕/ŶĐ

FLIGHT CONTROLS General External Features of Pitch Trim Actuator Figure 1 Electronic Connectors End Fitting Casing Moveable Tube Housing Cap Moveable Tube Housing Jam Nut Rod Ends

Issued: July 29, 2024 Revised: January 27, 2026 CC7-27-038R3 Page 9 of 10

SERVICE BULLETIN KŶƟĐŶŐŝŶĞĞƌŝŶŐĂŶĚDĂŶƵĨĂĐƚƵƌŝŶŐ͕/ŶĐ SA227 SERIES

COMMUTER CATEGORY

FLIGHT CONTROLS Inspection of Actuator Casing Lower Seal Joint Figure 2 Actuator Casing Juncture of Actuator Casing with Base of Actuator

Issued: July 29, 2024 Revised: January 27, 2026 CC7-27-038R3 Page 10 of 10

SERVICE BULLETIN SA227 SERIES

COMMUTER CATEGORY KŶƟĐŶŐŝŶĞĞƌŝŶŐĂŶĚDĂŶƵĨĂĐƚƵƌŝŶŐ͕/ŶĐ

FLIGHT CONTROLS Rod End Fillet Seal Location 1 Jam Nut Lock Washer Stop Nut Housing Moving Tube Insert Fillet Seal Location 2 Fillet Seal Location 3 Inspection of Actuator Upper Components and Seal Joints Figure 3 Moving Tube.

No sealant on surface of Moving Tube shown in this view.

Stop Nut Insert Jam Nut Rod End Lock Washer Top of Moving Tube.

Fillet seal between this surface and lock washer.

Circumference of Moving Tube. No sealant on this surface.

SERVICE BULLETIN COMPLIANCE FORM CC7-27-038R3 TO: OPERATOR OR SER VICE FACILITY ACCOMPLISHING BULLETIN Please complete this compliance form, and mail according to the instructions on the reverse side.

Thank you for returning this form.

************************************************************************************************** Aircraft Model Aircraft Serial Number Bulletin Issue Date Revision Date Aircraft Registration Number Operator/Owner Time on Aircraft Date Accomplished Comments KŶƟĐŶŐŝŶĞĞƌŝŶŐĂŶĚDĂŶƵĨĂĐƚƵƌŝŶŐ͕/ŶĐ

Pages 13–13 of 13