Copy · U.S. DOT/FAA - Piaggio Service Bulletin 80-0345 · 9 pages

© Piaggio. Filed by the FAA in regulations.gov docket FAA-2013-0527; AD 2013-18-04 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

TextOCR

This text is OCR from a scan. OCR can misread letters and numbers.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '3beedce8687e5a716c2c09fe25df7497114db28df6c121976ad34faeb0afcdfb'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Page 1OCROpen in PDF

PIAGGIO PIAGGIO AERO INDUSTRIES S.p.A.

AERO Via Cibrario, 4 - 16154 Genoa, Italy Product Support Department The EASA states mandatory compliance with inspections, modifications or technical directives and related time compliance by means of relevant Airworthiness Directives.

SERVICE BULLETIN (MANDATORY) N.: 80-0345 REV.0 ATA CHAPTER: 32-00 MODIFICATION N.: N/A TITLE: MAIN LANDING GEAR LEVER HINGE FITTING INSPECTION

REVISION STATUS OF THE BULLETIN This Service Bulletin is at the original issue and consists of 9 pages, plus Appendix A (Messier- Dowty Ltd. Service Bulletin no. P180-32-32, 1+8 pages).

1. PLANNING INFORMATION A. EFFECTIVITY Piaggio Aero Industries P180 Avanti and Avanti II Manufacturer's Serial Number (MSN):

1002; from 1004 and up, installing Main Landing Gear 201416 series, 201459 series and 201034 series.

B. CONCURRENT REQUIREMENTS N/A C. REASON During a scheduled maintenance inspection, evidence of cracks has been identified on the Main Landing Gear (MLG) lever hinge fitting (LHF) in correspondence of the joint between the hinge pin sub-assembly and the lock pin. This condition, if not detected and corrected, could lead to a serious structural defect of the Main Landing Gear, possibly resulting in damage to the aircraft and/or injury to the occupants.

As a temporary corrective action, additional inspections are required on in-service Main Landing Gear Lever Hinge Fittings.

Regulatory action is expected.

D. DESCRIPTION General This Service Bulletin consist of the following additional checks:

1. Check for freedom of rotation of the main landing gear wheel lever subassembly

2. Repetitive visual inspection of the main landing gear lever hinge fittings

3. Repetitive fluorescent penetrant inspections of the main landing gear lever hinge fittings.

Depending on inspection results, replacement of the failed item with a serviceable one may be required.

Original Issue: 20 September 2012 Service Bulletin: 80-0345 Rev. N. 0 Date: Page: 1 of 9

Page 2OCROpen in PDF

PIAGGIO PIAGGIO AERO INDUSTRIES S.p.A.

AERO Via Cibrario, 4 - 16154 Genoa, Italy Product Support Department E. COMPLIANCE This MANDATORY Service Bulletin shall be accomplished as follows:

- Part 1 - Check for freedom of rotation of the main landing gear wheel lever subassemblies: this one-off" check is required on all MLG installed on airplanes listed under "Effectivity" section of this Service Bulletin; unless already done, it is required within 200 landings, or three (3) months, whichever occurs first, from the issue date of this Service Bulletin, and following replacement of a MLG.

Part 2 - Visual inspection of the main landing gear lever hinge fittings: this check is required on all Lever Hinge Fittings (part of MLG), when installed on airplanes listed under "Effectivity" section of this Service Bulletin. Unless already done in the previous 200 landings, perform this check initially as specified in Table 1. If the "Check for freedom of rotation" described in part 1 of the accomplishment instruction does not pass, initially perform this check before next flight of the LF installed on the MLG that did not pass the test. After initial inspection, repeat the check at intervals not to exceed 200 landings, until retirement from service of the LHF, as long as this Service Bulletin is active.

Part 3 - Fluorescent penetrant inspections of the main landing gear lever hinge fittings: this check is required on all Lever Hinge Fittings (part of MLG), when installed on airplanes listed under "Effectivity" section of this Service Bulletin.

Unless already done in the previous 750 landings, perform this check initially as specified in Table 1. If the "Check for freedom of rotation" described in part 1 of the accomplishment instruction does not pass, initially perform this check before next flight of the LHF installed on the MLG that did not pass the test. After initial inspection, repeat the check at intervals not to exceed 750 landings, until retirement from service of the LHF, as long as this Service Bulletin is active.

LHF Cycles since new (CSN) Compliance required CSN ≤ 2300 Within 2500 CSN 2300 < CSN < 2500 Within 200 landings from the issue date of this Service Bulletin CSN ≥ 2500 Within 200 landings or three (3) months (whichever occurs first) from the issue date of this Service Bulletin Table 1 NOTE: RH and LH MLG may have different compliance limits.

In compliance with this Service Bulletin, please complete the attached Confirmation Slip and send it back to Piaggio Aero Industries S.p.A. - Product Support Department.

Original Issue: 20 September 2012 Service Bulletin: 80-0345 Rev. N. 0 Date: Page: 2 of 9

Page 3OCROpen in PDF

PIAGGIO PIAGGIO AERO INDUSTRIES S.p.A.

AERO Via Cibrario, 4 - 16154 Genoa, Italy Product Support Department F. APPROVAL The technical content of this Service Bulletin has been approved under the Authority of DOA No EASA.21J.220.

G. MANPOWER This MANDATORY Service Bulletin may be accomplished in approximately:

Part 1 - 2 man-hours (MH) per airplane.

Part 2 - 2 man-hours (MH) per airplane.

Part 3 - 7 man-hours (MH) per airplane.

H. TECHNICAL INFORMATION For questions concerning the technical content of this Service Bulletin, please contact:

Piaggio Aero Industries - Product Support Department Via Cibrario, 4 - 16154 Genoa, Italy Fax No. : + 39 010 6481 374 E-mail: tech.support@piaggioaero.it I. MATERIAL - COST AND AVAILABILITY Please contact:

Piaggio Aero Industries - Customer Support Department Via Cibrario, 4 - 16154 Genoa, Italy Telephone No.: +39 010 6481 800 Fax No.: +39 010 6481 891 E-Mail: commercialcustomersupport@piaggioaero.it J. TOOLING - COST AND AVAILABILITY No special tools are required.

K. WEIGHT AND BALANCE N/A L. ELECTRICAL LOAD DATA N/A Original Issue: 20 September 2012 Service Bulletin: 80-0345 Rev. N. 0 Date: Page: 3 of 9

Page 4OCROpen in PDF

PIAGGIO/ PIAGGIO AERO INDUSTRIES S.p.A.

AERO Via Cibrario, 4 - 16154 Genoa, Italy Product Support Department M. REFERENCES Document Title Document Number Chapter/Section Aircraft Maintenance Manual (AMM) 180-MAN-0200-01105 (Avanti II) 9066 (Avanti) 32-11-00 07-10-00 Messier Dowty Ltd. - Service Bulletin P180-32-32 N. PUBLICATIONS AFFECTED N/A Original Issue: 20 September 2012 Service Bulletin: 80-0345 Rev. N. 0 Date: Page: 4 of 9

Page 5OCROpen in PDF

PIAGGIO T AERO Via Cibrario, 4 - 16154 Genoa, Italy PIAGGIO AERO INDUSTRIES S.p.A.

Product Support Department

2. ACCOMPLISHMENT INSTRUCTIONS Procedure NOTE

WITHIN THE SCOPE OF THIS SERVICE BULLETIN, A MAIN LANDING GEAR IS DEEMED SERVICEABLE IF:

- It passes the check for freedom of rotation described in Part 1 of the Accomplishment Instructions, and following inspections described in Part 2 and Part 3 of the Accomplishment Instructions, when performed in accordance with compliance section, no cracks are identified on its Lever Hinge Fitting.

NOTE WITHIN THE SCOPE OF THIS SERVICE BULLETIN, "REPLACE THE MAIN LANDING GEAR WITH A SERVICEABLE ONE" MEANS:

- Remove the unserviceable MLG and replace it with a different serviceable MLG OR

- Rework the unserviceable MLG until it passes the check for freedom of rotation and, following inspections described in Part 2 and Part 3 of the Accomplishment Instructions, no cracks are identified on its Lever Hinge Fitting.

OR

- Replace the cracked LHF in the unserviceable MLG with a new LHF and, after LHF replacement, check the MLG for freedom of rotation.

Part 1 - Check for freedom of rotation of the main landing gear wheel lever subassemblies

(1) Jack the aircraft (refer to AMM Ch. 07-10-00).

(2) With reference to figure 2, perform a visual inspection for cracks of the main landing gear lever hinge fitting, in the area around the slot. If necessary, clean the area with a cloth before performing the inspection.

(3) If, following the inspection, cracks are identified, replace the main landing gear with a serviceable one before next flight. Complete the attached Confirmation Slip and send it back to Piaggio Aero Industries S.p.A. - Product Support Department.

Original Issue: 20 September 2012 Service Bulletin: 80-0345 Rev. N. 0 Date: Page: 5 of 9

Page 6OCROpen in PDF

PIAGGIO PIAGGIO AERO INDUSTRIES S.p.A.

AERO Via Cibrario, 4 - 16154 Genoa, Italy Product Support Department

(4) In accordance with Messier-Dowty Ltd. Service Bulletin P180-32-32, perform *Procedure A", steps 2 to 6.

(5) If the landing gear has not passed the test:

a. If the Lever Hinge Fitting has less than 2500 landings since new (CSN), using an indelible pen mark the LHF as "inspect as per SB-80-0345", then replace the affected landing gear with a serviceable one before next flight.

Make a note, recording type of inspection, date of inspection and inspection results, in aircraft log-book and in the affected landing gear documentation.

Complete the attached Confirmation Slip and send it back to Piaggio Aero Industries S.p.A. - Product Support Department.

CAUTION: The LHF installed on affected MLG must be inspected in accordance with the compliance section of this Service Bulletin.

b. If the Lever Hinge Fitting has 2500 or more landings since new (CSN), replace the affected landing gear with a serviceable one before next flight.

Make a note, recording type of inspection, date of inspection and inspection results, in aircraft log-book and in the affected landing gear documentation.

Complete the attached Confirmation Slip and send it back to Piaggio Aero Industries S.p.A. - Product Support Department.

CAUTION: The LF installed on affected MLG must be inspected in accordance with the compliance section of this Service Bulletin.

(6) Remove the aircraft from jacks (refer to AMM Ch. 07-10-00).

(7) Make an appropriate entry in the airplane logbook to show compliance with this section of this Service Bulletin.

Part 2 - Visual inspection of the main landing gear lever hinge fittings

(8) Jack the aircraft (refer to AMM Ch. 07-10-00).

(9) In accordance with Messier-Dowty Ltd. Service Bulletin P180-32-32, perform "Procedure B", steps 2 to 5

(10) If, following the inspection, cracks are identified, replace the main landing gear with a serviceable one before next flight. Complete the attached Confirmation Slip and send it back to Piaggio Aero Industries S.p.A. - Product Support Department.

(11) Remove the aircraft from jacks (refer to AMM Ch. 07-10-00).

Original Issue: 20 September 2012 Service Bulletin: 80-0345 Rev. N. 0 Date: Page: 6 of 9

Page 7OCROpen in PDF

PIAGGIO PIAGGIO AERO INDUSTRIES S.p.A.

AERO Via Cibrario, 4 - 16154 Genoa, Italy Product Support Department

(12) Make an appropriate entry in the airplane logbook to show compliance with this section of this Service Bulletin.

Part 3 - Fluorescent penetrant inspections of the main landing gear lever hinge fittings

(13) Jack the aircraft (refer to AMM Ch. 07-10-00).

(14) In accordance with Messier-Dowty Ltd. Service Bulletin P180-32-32, perform "Procedure C", steps 2 to 8

(15)If, following the inspection, cracks are identified, replace the main landing gear with a serviceable one before next flight.

(16) Remove the aircraft from jacks (refer to AMM Ch. 07-10-00).

(17) Complete the attached Confirmation Slip and send it back to Piaggio Aero Industries S.p.A. - Product Support Department.

(18)Make an appropriate entry in the airplane logbook to show compliance with this section of this Service Bulletin.

LEVER HINGE _ PINTLE PIN

SUB-ASS WEIGHT

CK ABSORBER

SUB-ASSEMBLY

AXLE RETAINING PIN

AXLE NUT FIGURE 1 - Main Landing Gear: lever hinge fitting (LH shown).

Original Issue: 20 September 2012 Service Bulletin: 80-0345 Rev. N. 0 Date: Page: 7 of 9

Page 8OCROpen in PDF

PIAGGIO PIAGGIO AERO INDUSTRIES S.p.A.

AERO Via Cibrario, 4 - 16154 Genoa, Italy Product Support Department FIGURE 2 - Main Landing Gear LHF - crack.

Original Issue: 20 September 2012 Service Bulletin: 80-0345 Rev. N. O Date: Page: 8 of 9

Page 9OCROpen in PDF

PIAGGIO PIAGGIO AERO INDUSTRIES S.p.A.

AERO Via Cibrario, 4 - 16154 Genoa, Italy Product Support Department

3. MATERIAL INFORMATION A. LIST OF MODIFICATION KIT COMPONENTS N/A B. LIST OF MATERIALS - OPERATOR SUPPLIED N/A C. LIST OF TOOLS N/A D. DISPOSAL OF REMOVED PART N/A E. WARRANTY CREDIT PROGRAM N/A

4. WARNING - PROPRIETARY RIGHTS This bulletin contains proprietary information of Piaggio Aero Industries S.p.A. (PAI), which PAI provides in confidence and solely for the purposes of supporting PAI products and providing applicable information regarding the proper use, maintenance, inspection, repair, servicing and parts application of PAI products. Neither this bulletin nor any information in it may be disclosed to others, or used for any other purpose, including, without limitation, to design, create, develop, reproduce, manufacture or derive any design, part, product, material, process, modification, configuration change or repair, or obtain any government approval to do so. This material is the exclusive property of Piaggio Aero Industries S.p.A. and therefore shall not be reproduced, used or disclosed to others except as authorized by contract with Piaggio Aero Industries S.p.A. or without the written permission of Piaggio Aero Industries S.p.A..

Original Issue: 20 September 2012 Service Bulletin: 80-0345 Rev. N. O Date: Page: 9 of 9