TextOCR
This text is OCR from a scan. OCR can misread letters and numbers.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '4b84645d26a2b668377d2e4b9c8fa5d48a24482e4880ecbd4d6d06d9e27007dc' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '4b84645d26a2b668377d2e4b9c8fa5d48a24482e4880ecbd4d6d06d9e27007dc' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
PIAGGIO AERO INDUSTRIES S.p.A.
PIAGGIO p AERO Via Cibrario, 4 - 16154 Genoa, Italy Product Support Department The EASA states mandatory compliance with inspections, modifications or technical directives and related time compliance by means of relevant Airworthiness Directives.
SERVICE BULLETIN (MANDATORY) N.: 80-0381 REV.O ATA CHAPTER: 27-00 MODIFICATION N.: N/A TITLE: HORIZONTAL STABILIZER TO ELEVATOR CLEARANCE VERIFICATION AND
MINOR REWORK
REVISION STATUS OF THE BULLETIN This Service Bulletin is at the original issue and consists of 9 pages.
1. PLANNING INFORMATION A. EFFECTIVITY Piaggio Aero Industries P180 Avanti and Avanti II Manufacturer's Serial Number (MSN):
1002 and from 1004 thru 1231.
B. CONCURRENT REQUIREMENTS N/A.
C. REASON The spanwise clearance between the horizontal stabilizer end rib and the elevator horn was measured lower than minimum on an in-service aircraft. According to preliminary investigation, similar installation may be found on airplanes listed under effectivity section of this Service Bulletin.
A procedure to measure the clearance and to restore an acceptable margin is provided in this Service Bulletin.
D. DESCRIPTION General This Service Bulletin consists of the following actions:
Part A
• Measurement of the clearance between the elevator horn and the horizontal stabilizer tip rib Part B (if applicable, should the clearance result below the minimum allowed)
• Elevator removal
• Adjustment of the Elevator Bellcrank installation;
• Elevator installation and final check of the clearance;
Part C
• Data reporting to Piaggio Aero Technical Support.
Original Issue: May 02, 2013 Service Bulletin: 80-0381 Rev. N. 0 Date: Page: 1 of 9
PIAGGIO PIAGGIO AERO INDUSTRIES S.p.A.
AERO Via Cibrario, 4 - 16154 Genoa, Italy Product Support Department E. COMPLIANCE This Service Bulletin shall be accomplished as follows:
- Perform this Service Bulletin within 200FH or 12 months, whichever occurs first, from the issue date of this Service Bulletin.
The clearance check (refer to Accomplishment Instructions - Part A) may not be performed if all the following conditions are met:
- The minimum clearance was measured, on both LH and RH sides, during the previous 3 month from the issue date of this Service Bulletin.
- Measured clearance was at least 5 mm on both sides.
Part C shall in any case be accomplished.
In compliance with this Service Bulletin, please complete the attached Confirmation Slip and send it back to Piaggio Aero Industries S.p.A. - Product Support Department.
F. APPROVAL The technical content of this Service Bulletin has been approved under the Authority of DOA No EASA.21J.220.
G. MANPOWER This MANDATORY Service Bulletin may be accomplished in approximately:
- Part A+C: 1 man-hour (MH).
- Part B (if required): 4 man-hours (MH).
H. TECHNICAL INFORMATION For questions concerning the technical content of this Service Bulletin, please contact:
Piaggio Aero Industries - Product Support Department Via Cibrario, 4 - 16154 Genoa, Italy Fax No. : + 39 010 6481 374 E-mail: tech.support@piaggioaero.it Original Issue: May 02, 2013 Service Bulletin: 80-0381 Rev. N. 0 Date: Page: 2 of 9
PIAGGIO PIAGGIO AERO INDUSTRIES S.p.A.
AERO Via Cibrario, 4 - 16154 Genoa, Italy Product Support Department I. MATERIAL - COST AND AVAILABILITY For pricing, availability and scheduling, please contact:
- for customers and operators in Europe, Asia and RoW e-mail: spareparts@piaggioaero.it telephone: (+39) 010 6481 889 fax: (+39) 010 6481 891
- for customers and operators in the Americas e-mail: SparepartsPAM@piaggioamerica.com telephone : (+1) 561 253 0104 fax: (+1) 561 683 5513 J. TOOLING - COST AND AVAILABILITY N/A K. WEIGHT AND BALANCE N/A L. ELECTRICAL LOAD DATA N/A M. REFERENCES Document Title Document Number Chapter/Section Avanti Aircraft Maintenance Manual (AMM) 9069 27-30-00 27-40-00 Avanti II Aircraft Maintenance Manual (AMM) 180-MAN-0200-01105 55-10-00 N. PUBLICATIONS AFFECTED N/A Original Issue: May 02, 2013 Service Bulletin: 80-0381 Rev. N. 0 Date: Page: 3 of 9
PIAGGIO AERO INDUSTRIES S.p.A.
PIAGGIO/ AERO Via Cibrario, 4 - 16154 Genoa, Italy Product Support Department
2. ACCOMPLISHMENT INSTRUCTIONS Procedure PART A - Clearance check NOTE: WITHIN THE SCOPE OF THIS SERVICE BULLETIN, "ELEVATOR IN NEUTRAL POSITION" MEANS THAT THE ELEVATOR LOWER
SURFACE IS ALIGNED WITH THE HORIZONTAL STABILIZER LOWER SURFACE.
1. With the elevators in neutral position (elevator at angle = 0°), measure the minimum clearance between the LH and RH elevator horns (see Fig. 1) and the horizontal stabilizer (HS) end ribs. You may use a cylindrical rod (or equivalent), verifying it moves freely across the entire length of the exposed area.
2. Record the values in the table on the confirmation sheet.
Based on the clearance values:
If the minimum value is at least 5mm or more on both HS sides, leave the structure as it is. Mark "Not necessary" on Part B of the confirmation sheet and send it back to Piaggio Aero, then proceed with Part C of this Service Bulletin.
If the minimum clearance is less than 5mm on any HS side, perform Part B of this Service Bulletin on RH and/or LH HS side.
5mm MIN Fig. 1 - Clearance measurement Original Issue: May 02, 2013 Service Bulletin: 80-0381 Rev. N. 0 Date: Page: 4 of 9
PIAGGIO AERO INDUSTRIES S.p.A.
PIAGGIO AERO Via Cibrario, 4 - 16154 Genoa, Italy Product Support Department PART B - Minor rework NOTE: THE FOLLOWING PROCEDURE MAY BE APPLIED ON RH AND LH
SIDE OF THE TAIL PLANE, AS REQUIRED Remove the rear fairing from the top of the vertical stabilizer.
5. Remove the elevator in accordance with AMM chap. 27-30-00.
Verify if the countersunk washer P/N MS20002C6 (see Fig. 2, Fig. 3) is installed on elevator. If the washer is not installed, proceed with step (7), otherwise proceed with step (8).
washer P/N MS20002C6 N. 2 threads minimum out of the nut
• 2 NUT
• 3 WASHER
BEARING Elevator to stabilizer distance ELEVATOR BELLCRANK - 5 BOLT 7 NUT 6 WASHER Fig. 2 - Detailed sketch of the elevator bellcrank Original Issue: May 02, 2013 Service Bulletin: 80-0381 Rev. N. 0 Date: Page: 5 of 9
PIAGGIO PIAGGIO AERO INDUSTRIES S.p.A.
AERO Via Cibrario, 4 - 16154 Genoa, Italy Product Support Department Countersunk washer MS20002C6 (countersink Elevator body towards the elevator body) Fig. 3 - Picture of the elevator bellcrank with the countersunk washer installed NOTE: THE WASHER SHALL BE LOCKED TO THE ELEVATOR BELLCRANK WITH LOCTITE (RC680, 222 OR EQUIVALENT)
7. If, following step 6, countersunk washer P/N MS20002C6 is found not installed, install a new countersunk washer P/N MS20002C6, then temporary install the elevator and repeat step 1. If the minimum clearance is at least 5 mm, go to step (9), otherwise proceed with step (8).
NOTE: THE NEW WASHER P/N MS20002-6 SHALL BE LOCKED TO THE EXISTING WASHER P/N MS20002C6 WITH LOCTITE (RC680, 222
OR EQUIVALENT) NOTE: DURING ELEVATOR INSTALLATION, MAKE SURE THAT THERE ARE AT LEAST N. 2 THREADS OUT OF THE NUT (SEE Fig. 2) FIXING THE ELEVATOR TO THE BUSHING/STABILIZER ASSY.
8. If, following step (6), the countersunk washer P/N MS20002C6 is found installed, or if required after accomplishment of step (7), add a new washer plain P/N MS20002-6 (plain) to the existing one in order to increase the distance between the elevator and the stabilizer by 2mm (see Fig. 4, Fig. 5).
Original Issue: May 02, 2013 Service Bulletin: 80-0381 Rev. N. 0 Date: Page: 6 of 9
PIAGGIO AERO INDUSTRIES S.p.A.
PIAGGIO AERO Via Cibrario, 4 - 16154 Genoa, Italy Product Support Department Plain washer MS20002-6 Countersink Fig. 4 - Picture of the elevator bellcrank with the countersunk and plain washers installed Plain washer MS20002-6 Countersunk washer MS20002C6 (countersink towards the elevator body) Fig. 5 - Picture of the elevator bellcrank with the countersunk and plain washers installed Original Issue: May 02, 2013 Service Bulletin: 80-0381 Rev. N. 0 Date: Page: 7 of 9
PIAGGIO/ PIAGGIO AERO INDUSTRIES S.p.A.
AERO Via Cibrario, 4 - 16154 Genoa, Italy Product Support Department
9. Install the elevator in accordance with AMM chap. 27-30-00
10. Repeat step (1) to make sure the minimum clearance is at least 5 mm.
11. Install the top fin fairing aft.
PART C - Data Reporting to Piaggio Aero Industries
12. Complete the attached Confirmation Slip and send it back to Piaggio Aero Industries S.p.a. - Product Support Department.
13. Make an opportune entry in the airplane logbook to show compliance with this Service Bulletin.
Original Issue: May 02, 2013 Service Bulletin: 80-0381 Rev. N. 0 Date: Page: 8 of 9
PIAGGIO PIAGGIO AERO INDUSTRIES S.p.A.
AERO Via Cibrario, 4 - 16154 Genoa, Italy Product Support Department
3. MATERIAL INFORMATION A. LIST OF MODIFICATION KIT COMPONENTS B. LIST OF MATERIALS - OPERATOR SUPPLIED Part/Number Specification Supplier Qty. Designation MS20002C6 Standard/Any Source A/R (max 2) Washer - countersunk MS20002-6 Standard/Any Source A/R (max 2) Washer - Plain loctite Standard/Any Source A/R C. LIST OF TOOLS N/A D. DISPOSAL OF REMOVED PART N/A E. WARRANTY CREDIT PROGRAM N/A
4. WARNING - PROPRIETARY RIGHTS This bulletin contains proprietary information of Piaggio Aero Industries S.p.A. (PAI), which PAI provides in confidence and solely for the purposes of supporting PAI products and providing applicable information regarding the proper use, maintenance, inspection, repair, servicing and parts application of PAI products. Neither this bulletin nor any information in it may be disclosed to others, or used for any other purpose, including, without limitation, to design, create, develop, reproduce, manufacture or derive any design, part, product, material, process, modification, configuration change or repair, or obtain any government approval to do so. This material is the exclusive property of Piaggio Aero Industries S.p.A. and therefore shall not be reproduced, used or disclosed to others except as authorized by contract with Piaggio Aero Industries S.p.A. or without the written permission of Piaggio Aero Industries S.p.A.
Original Issue: May 02, 2013 Service Bulletin: 80-0381 Rev. N. 0 Date: Page: 9 of 9
PIAGGIO AERO INDUSTRIES S.p.A.
PIAGERO P Via Cibrario, 4 - 16154 Genoa, Italy Product Support Department
CONFIRMATION SLIP Service Bulletin Accomplishment SB-0381 Rev.0 A/C S/N: A/C Flight Hours: A/C LGDS: A/C Registration:
Date:
Accomplished by:
Signature INSPECTION RESULTS:
LH side RH side PART A - Clearance check _mm mm
• Done • Done PART B - Minor rework
• Not necessary • Not necessary