Copy · PC-6_SB 53-003 R1 · 24 pages

© Pilatus Aircraft Ltd. Filed by the FAA in regulations.gov docket FAA-2016-9356; AD 2016-22-12 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Text

From the PDF’s text layer: layout, tables and figures are lost. The PDF is the document.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = 'aec07bd235a658007ac37936668ad65a7649e56c5bcc9f4e2eed5405c869beca'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Service Bulletin No: 53-003 Ref No: 215 Modification No: INSPECTION ATA Chapter: 53

SERVICE BULLETIN PILATUS AIRCRAFT LTD. STANS, SWITZERLAND Service Bulletin No: 53-003 Date: Oct 04/16 Rev. No. 1 Date: Oct 13/16 Page 1 of 24

FUSELAGE - REAR FUSELAGE

STABILIZER-TRIM ATTACHMENT COMPONENTS - INSPECTION

1. Planning Information A. Effectivity Pilatus PC-6 Series aircraft MSNs 337 thru 1005.

Fairchild built PC-6 aircraft MSNs 2001 thru 2092.

All PC-6 horizontal stabilizer assemblies, stabilizer control-system fittings, connecting pieces, bearing supports and bearing forks held as spares.

B. Concurrent Requirements None.

This Service Bulletin applies to the Post SB 53-001 Revision 1 configuration.

C. Reason

(1) Problem Wear and cracks have been reported in the following Post SB 53-001 R1 stabilizer-trim attachment and structural components:

• Fitting (116.40.06.112) or (116.40.06.033) in aircraft with electrical horizontalstabilizer control-systems (CONFIG 1 aircraft)

• Connecting piece (6232.0026 - all varian ts) in aircraft with mechanical horizontalstabilizer control-systems (CONFIG 2 aircraft).

(2) Cause It is possible that slightly asymmetric installation and/or operational conditions resulting in strong stabilizer vibration can cause the initiation of cracks.

Service Bulletin No: 53-003 Date: Oct 04/16 Rev. No. 1 Date: Oct 13/16 Page 2 of 24

SERVICE BULLETIN

(3) Solution NOTE: As an alternative to the inspections detailed in (a) and (b) you can replace the non-inspected items. Replacement instead of inspection satisfies the requirements of this Service Bulletin.

(a) Before the next flight:

Do a visual inspection for crack damage in the applicable stabilizer-trim attachment components, and the related parts and structure. The stabilizer-trim actuator and the fitting or connecting piece must be removed to do the inspection. No cracks are permitted. Replace all crack damaged components and structure before the next flight.

NOTE: If the fitting or connecting piece has been in service for not more than 100 flight hours and not more than 100 landings at the issue date of this SB, the visual inspection before next flight is not necessary.

(b) Within 100 flight hours or 100 landings (whichever comes first):

(i) Do a visual inspection for crack da mage in the applicable stabilizer-trim attachment components, and the related parts and structure. No cracks are permitted. Replace all crack damaged components before the next flight.

(ii) Remove the surface finish and do a dye-penetrant inspection for crack damage in the applicable stabilizer-trim attachment components, and the related parts and structure. No cracks are permitted. Replace all crack damaged components before the next flight.

NOTE: As an alternative to the dye-penetrant inspection you can do an eddy current inspection, which does not require removal of the surface finish. A right-angled shaft surface-probe with minimal drop is required to inspect in the gap between the lugs of the components:

- CONFIG 1 aircraft - smallest gap is 12,7 mm (0.5 in.).

- CONFIG 2 aircraft - smallest gap is 6 mm (0.24 in.).

(c) Before installation on an aircraft or within 6 months (whichever comes first):

(i) Do the inspection, detailed in Para. (3)(b) above, of all PC-6 horizontal stabilizer assemblies held as spares. Replace all crack damaged components before installation on an aircraft.

(ii) Do the inspection, detailed in Para. (3 )(b) above, of all PC-6 stabilizer controlsystem fittings, connecting pieces, bearing supports and bearing forks held as spares. Discard all crack damaged parts.

SERVICE BULLETIN Service Bulletin No: 53-003 Date: Oct 04/16 Rev. No. 1 Date: Oct 13/16 Page 3 of 24 D. Description This Service Bulletin gives the data and instructions to do inspections for crack damage in the applicable stabilizer-trim attachment components and to replace defective components (if necessary).

Revision 1 is issued to:

• Show the screw (16), washer (17) and nut (18) on Fig. 1 and include them in the parts lists and procedures

• Correct two cross-references on Page 10 and correct the SB reference in the title of Fig. 2.

If operators have replaced the bearing fork (Fig. 1, Item 12) in accordance with the initial issue of this Service Bulletin, they must make sure it is installed with two bolts and one screw.

E. Compliance Mandatory.

The visual inspection is required before the next flight, if:

• The fitting (on CONFIG 1 aircra ft) P/N 116.40.06.112 or 116.40.06.033 has been in service for more than 100 flying hours or 100 landings at the issue date of this Service Bulletin

• The connecting piece (on CONFIG 2 aircraft) P/N 6232.0026 has been in service for more than 100 flying hours or 100 landings at the issue date of this Service Bulletin.

The non-destructive inspection is required within 100 flight hours or 100 landings (whichever comes first) after the issue date of this Service Bulletin.

Horizontal stabilizer assemblies, stabilizer control-system fittings, connecting pieces, bearing supports and bearing forks held as spares are to be inspected before installation on an aircraft or within 6 months (whichever comes first) after the issue date of this Service Bulletin.

F. Approval The technical content of this Service Bulletin is approved under the authority of DOA No. EASA.

21J. 357.

PILATUS advises Operators/Owners to check with their designated Airworthiness Authorities for any changes, local regulations or sanctions that may affect the embodiment of this Service Bulletin.

G. Copyright and Legal Statements © Pilatus Aircraft Ltd. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be copied, reproduced or translated to other languages without the prior written consent of Pilatus Aircraft Ltd.

In connection with the use of this document, Pilatus does not provide any express or implied warranties and expressly disclaims any warranty of merchantability or fitness for a particular purpose. This document contains trade secrets, confidential and/or proprietary information of Pilatus and technical data subject to export control laws and regulations, including the U.S.

Export Administration Regulations (EAR). Disclosure or distribution of this document contrary to the EAR, and other laws and regulations, is strictly forbidden. The above restrictions may apply to data on all pages of this document.

Service Bulletin No: 53-003 Date: Oct 04/16 Rev. No. 1 Date: Oct 13/16 Page 4 of 24

SERVICE BULLETIN H. Manpower NOTE: Man-hours figures do not include the time required to cure sealants and adhesives.

I. Weight and Balance

(1) Weight Change None.

(2) Moment Change None.

J. Electrical Load Data Not changed.

K. Software Not changed.

L. References PC-6 aircraft except B2-H2/B2-H4:

• Airworthiness Limitations (AL) Doc. 02334: Appendix E and J.

• Repair and Overhaul Manual (ROM): Chapter 2 and 12.

PC-6 aircraft B2-H2/B2-H4:

• Aircraft Maintenance Manual (AMM) Doc. 01975: 27-45-11, 55-11-11.

• Structural Repair Manual (SRM): 51-00-03. 51-00-05, 51-00-06, 51-00-09.

Total (Inspection) Total (Replacements) CONFIG 1 CONFIG 2 CONFIG 1 CONFIG 2 Preparation 1.0 1.0 - - Removal 0.5 0.5 - - Inspection A - Visual 0.5 0.5 - - Inspection B - NDI 0.5 0.5 - - Installation/Replacement of Fitting/ Connecting Piece

1.5 1.5 - - Replacement of Bearing Fork/Bearing Supports -- 4 . 0 6 . 0 Close up 0.5 0.5 - - TOTAL MAN-HOURS 4.5 4.5 4.0 6.0

SERVICE BULLETIN Service Bulletin No: 53-003 Date: Oct 04/16 Rev. No. 1 Date: Oct 13/16 Page 5 of 24 M. Publications Affected None.

N. Interchangeability of Parts Not applicable.

Service Bulletin No: 53-003 Date: Oct 04/16 Rev. No. 1 Date: Oct 13/16 Page 6 of 24

SERVICE BULLETIN

2. Material Information A. Material - Pric e and Availability No Modification Kit is required for this Service Bulletin.

Operators who require further information and/or Service Bulletin material should contact their Authorized Pilatus Service Center, or:.

Operators are requested to advise Pilatus Aircraft Ltd, of the Manufacturer’s Serial Number (MSN) and the flying hours and landings of aircraft which are affected by this Service Bulletin.

B. Material Necessary for Each Aircraft NOTE: Part numbers given in this Service Bulletin are correct at the time of approval. Pilatus Aircraft Ltd. reserves the right to change the part numbers as necessary. Part numbers of items delivered are correct when dispatched. This could lead to differences between those part numbers quoted in this Service Bulletin and the delivered parts, if parts are superseded. Operators are requested to check the IPC for delivered parts which differ from those listed in the Service Bulletin Materials List.

(1) Material to be Purchased Operators must order the following parts as necessary for replacement:

PILATUS AIRCRAFT LTD

CUSTOMER SUPPORT MANAGER CH-6371 STANS

SWITZERLAND General Aviation:

Tel: + 41 41 619 3333 Fax: + 41 41 619 7311 eMail: SupportPC12@pilatus-aircraft.com New Part No. Description Old Part No. Qty Disp.

Code Fig Item

112.35.06.197 6201.0134 FR12a Assembly 112.35.06.197 6201.0134 1R 1N / A

116.40.06.033 Fitting (CONFIG 1) 116.40.06.033 1 R 1 6

116.40.06.034 Bearing Fork (CONFIG 1)

116.40.06.034 1 R 1 12

116.40.06.112 Fitting - Post SB 147 (CONFIG 1)

116.40.06.112 1 R 1 N/A 6232.0026.01 Connecting Piece (CONFIG 2) 6232.0026.01 1 R 1 9 6304.0023.01 Bearing Support (Left) (CONFIG 2) 6304.0023.01 1 R 1 3 6304.0023.02 Bearing Support (Right) (CONFIG 2) 6304.0023.02 1 R 1 2

932.35.14.105 Bolt (NAS6604-5) (CONFIG 2)

932.35.14.105 1 D 1 8 Disposition Codes: D - Discard / N - New / R - Return to Pilatus

SERVICE BULLETIN Service Bulletin No: 53-003 Date: Oct 04/16 Rev. No. 1 Date: Oct 13/16 Page 7 of 24

(2) Operator Supplied Materials (Ref. AMM Do c. 01975, 20-31-00 or AL Doc. 02334, Appendix E) C. Material Necessary for Each Spare

(1) Material to be Purchased Operators must order the following parts as necessary for replacement:

932.35.14.109 Bolt (NAS6604-9) (CONFIG 2)

932.35.14.109 1 D 1 8 6201.0134.11 Washer (CONFI G 2) 6201.0134.11 7 D 1 10

938.07.68.305 Nut (MS21046-4E) (CONFIG 2)

938.07.68.305 2 D 1 11

931.54.41.720 Screw, Pan Head (NFL22271BC030020L) (CONFIG 2)

931.54.41.209 1 D 1 16

938.07.31.103 Nut (3PA108) (CONFIG 2)

938.07.34.100 1 D 1 18

938.71.51.103 Washer (NFL23111CA030) (CONFIG 2)

938.78.13.103 1 D 1 17 Material No. Description Qty Remarks P01-008 Solvent (White Spirit) A/R Or approved alternative P02-020 Scotch-Brite A/R P02-031 Absorbent Paper A/R P04-039 Corrosion Preventative A/R CA1000 P07-001 CCC Solution A/R P07-007 Epoxy Primer A/R N/A Permanent Marker Pen 1 Edding Aerospace Marker 8404 or equivalent New Part No. Description Old Part No. Qty Disp.

Code Fig Item

116.40.06.034 Bearing Fork (CONFIG 1)

116.40.06.034 1 R 1 12

116.40.06.033 Fitting (C ONFIG 1) 116.40.06.033 1 R 1 6 Disposition Codes: D - Discard / R - Return to Pilatus New Part No. Description Old Part No. Qty Disp.

Code Fig Item Disposition Codes: D - Discard / N - New / R - Return to Pilatus

Service Bulletin No: 53-003 Date: Oct 04/16 Rev. No. 1 Date: Oct 13/16 Page 8 of 24

SERVICE BULLETIN D. Re-identified Parts Not applicable.

E. Tooling - Cost and Availability Not applicable.

116.40.06.112 Fitting - Post SB 147 (CONFIG 1)

116.40.06.112 1 R 1 N/A 6304.0023.01 Bearing Support (Left) (CONFIG 2) 6304.0023.01 1 R 1 3 6304.0023.02 Bearing Support (Right) (CONFIG 2) 6304.0023.02 1 R 1 2 6232.0026.01 Connecting Piece (CONFIG 2) 6232.0026.01 1 R 1 9

931.54.41.720 Screw, Pan Head (NFL22271BC030020L) (CONFIG 2)

931.54.41.209 1 D 1 16

938.07.31.103 Nut (3PA108) (CONFIG 2)

938.07.34.100 1 D 1 18

938.71.51.103 Washer (NFL23111CA030) (CONFIG 2)

938.78.13.103 1 D 1 17 New Part No. Description Old Part No. Qty Disp.

Code Fig Item Disposition Codes: D - Discard / R - Return to Pilatus

SERVICE BULLETIN Service Bulletin No: 53-003 Date: Oct 04/16 Rev. No. 1 Date: Oct 13/16 Page 9 of 24

3. Accomplishment Inst ructions - Aircraft NOTE: AMM references given are applicable for holders of AMM Doc. 01975.

A. Preparation

(1) Remove the access panel FL2.

(2) CONFIG 1 Aircraft:

(a) Remove the horizontal stabilizer actuat or (Ref. AMM 27-45-11 (CONFIG 1), Page Block 401).

(3) CONFIG 2 Aircraft:

(a) Remove the horizontal stabilizer actuat or (Ref. AMM 27-45-11 (CONFIG 2), Page Block 401). During this procedure use clamps (or equivalent) to make sure the cables stay in position on the spools of the mechanical actuator and operating mechanism.

(4) Use applicable supports to ho ld the horizontal stabilizer in a position which gives access to bottom surface.

B. Removal (Ref. Fig. 1)

(1) CONFIG 1 Aircraft:

(a) Remove the nuts (7), washers (5), bolts (4).

(b) Remove the fitting (6) from FR12a.

(c) Record the part marking of the fitting (6) on the Report Form supplied with this Service Bulletin.

(d) Discard the fitting if it has incomplete or missing part marking, unless you can confirm the service history of the fitting from its documentation.

(2) CONFIG 2 Aircraft:

(a) Remove the nuts (11), washers (10), bolts (8) and disassemble the connecting piece (9) from FR12a.

(b) Record the part marking of the connectin g piece (9) on the Report Form supplied with this Service Bulletin.

(c) Discard the connecting piece if it has in complete or missing part marking, unless you can confirm the service history of the connecting piece from its documentation.

Service Bulletin No: 53-003 Date: Oct 04/16 Rev. No. 1 Date: Oct 13/16 Page 10 of 24

SERVICE BULLETIN C. Inspections (Ref. Fig. 1)

(1) Inspection A - Visual Inspection - Before the next flight:

(a) Remove loose paint if necessary, then us e absorbent paper (Material No. P02-031) and the solvent (Material No. P01-008) to clean:

• All surfaces of the fitting (6) or connecting piece (9)

• The surfaces of the bearing fork (12) or bearing supports (2) and (3) to which you have access

• The location on the surface of FR12a w here the fitting (6) or connecting piece

(9) was installed.

(b) Use a 10x magnifier and bright light to visually examine the following parts for damage, cracks and signs of uneven wear. No damage, cracks or uneven wear is permitted:

• The fitting (6) or connecting piece (9)

• The bearing fork (12) or bearing supports (2) and (3) to which you have access.

If you find uneven wear, contact Pilatus Aircraft Ltd.

(c) Use a 10x magnifier and bright light to visually examine the surface of FR12a where the fitting (6) or connecting piece (9) was installed for damage, cracks and corrosion. No damage or cracks are permitted. Remove surface corrosion if found (Ref. ROM Chap 2 or SRM 51-00-05). Discard the part if less than 90% of the original material thickness remains after removal of the corrosion.

(d) Use internal vernier callipers (or equi valent) to do a check of the actuator attachment hole diameters in the fitting (6) (CONFIG 1) and connecting piece (9) (CONFIG 2). Hole diameters of more than 9,555 mm (0.3762 in.) in the fitting or

16.036 mm (0.631 in.) in the connecting piece are not permitted. Replace defective components (Ref. Table 1 - Component Replacement Data).

(e) Use internal vernier calliper s (or equivalent) to do a check of the diameters of the attachment bolt holes in the fitting (6) (CONFIG 1) and FR12a (CONFIG 1). Hole diameters of more than 4,85 mm (0.191 in.) are not permitted. Replace the component if defective. If necessary, also replace FR12a, if the applicable holes for the fitting are out of limits (Ref. Table 1 - Component Replacement Data).

NOTE: If the Post SB 147 oversize bush (P/N 116.40.06.111) is installed, contact Pilatus Aircraft Ltd. for more information.

(f) Use internal vernier callipers (or equi valent instrument) to do a check of the diameters of the attachment bolt holes in the connecting piece (9) (CONFIG 2) and FR12a (CONFIG 2):

• If all of the hole diameters are 6,024 mm (0.23717 in.) or less, continue from Para D, Step (2)(b)

• If one or more of the holes are more than 6,024 mm (0.237 in.) but less than 6,35 mm (0.25 in.), continue from Para D, Step (2)(c)

SERVICE BULLETIN Service Bulletin No: 53-003 Date: Oct 04/16 Rev. No. 1 Date: Oct 13/16 Page 11 of 24

• If one or more holes are 6,35 mm (0.25 in.) or more, replace the connecting piece (9) and/or the FR12a (Ref. Table 1 - Component Replacement Data).

(2) Inspection B - Non-Destructive Inspection (NDI) - Within 100 flight hours or 100 landings (whichever comes first):

(a) Do Inspection A - Visual Insp ection (Ref. Para. 3.C.(1)).

NOTE: The following step (b) is only necessary if you will do a dye-penetrant NDI.

The eddy current NDI does not require the removal of surface treatment.

(b) Obey the manufacturers instructions and use the solvent (Material No. P01-008), Scotch-Brite (Material No P02-020) and/or non-metal scrapers to remove the layers of paint and protection from:

• All surfaces of the fitting (6) or connecting piece (9)

• The surfaces of the bearing fork (12) or bearing supports (2) and (3) to which you have access

• The location on the surface of FR12a where the fitting (6) or connecting piece

(9) was installed.

CAUTION: ONLY PERSONNEL QUALIFIED AND CERTIFIED TO THE APPLICABLE LEVEL II (OR HIGHER) OF NATIONAL AEROSPACE STANDARD NAS 410, EUROPEAN STANDARD EN 4179 OR MIL-STD-410E, OR EQUIVALENT AEROSPACE STANDARD, ARE PERMITTED TO DO THE NDI.

(c) Do a dye-penetrant NDI, or the alte rnative eddy current NDI, as follows:

NOTE: Refer to Airworthiness Limitations Doc. 02334, Appendix J, or SRM 51-00- 09 as applicable for the related inspection procedures.

(i) Do the NDI for cracks in all surfaces of the:

• Fitting (6) or connecting piece (9). Make sure you do a thorough inspection of the critical areas shown on Figure 3

• Bearing fork (12) or bearing supports (2) and (3)

• Applicable area of FR12a.

(ii) No crack damage is permitted. You must replace:

• Cracked components (Ref. Table 1 - Component Replacement Data)

• The two bearing supports (2) and (3) if only one is found cracked

• FR12a if cracks are found.

Service Bulletin No: 53-003 Date: Oct 04/16 Rev. No. 1 Date: Oct 13/16 Page 12 of 24

SERVICE BULLETIN D. Installation/Replacement (Ref. Fig. 1)

(1) Install the fitting on CONFIG 1 aircraft:

NOTE: The following Steps (a) and (b) are not required when using a new fitting P/N

116.40.06.112.

(a) Preparation of removed and inspected fitting:

(i) Obey the manufact urers instructions and apply layers of CCC solution (Material No. P07-001) as necessary to the applicable components and inspection areas (Ref. ROM Chap 12 or SRM 51-00-06).

(ii) Obey the manufacturers instructions a nd apply layers of primer (Material No.

P07-007) and paint as necessary to the applicable components and inspection areas (Ref. ROM Chap 12 or SRM 51-00-06).

(iii) Use a permanent marker pen to re-a pply the part markings as recorded during the removal procedure.

(b) Preparation of new fitting P/N 116.40.06.033:

(i) Use a suitable drill and reamer to increase the diameter of the three attachment holes to between 4,820 and 4,832 mm.

(ii) Obey the manufacturer s instructions and apply layers of CCC solution (Material No. P07-001) as necessary to the reamed holes (Ref. ROM Chap 12 or SRM 51-00-06).

(c) Obey the manufacturers instructions a nd apply layers of corrosion preventative (Material No. P04-039) on the faying surfaces of FR12a and the fitting (6), nuts (7), washers (5) and bolts (4).

(d) Put the fitting (6) in position on FR12 a and install the bolts (4), washers (5) and nuts (7).

Component Part No. Replacement FR12a Assembly 112.35.06.197 6201.0134 Ref. ROM Chap 2 or SRM 51-00-03 Fitting (CONFIG 1) 116.40.06. 033 Ref. Para D, Pre-Drilled Bearing Fork (CONFIG 1) 116.40.06.034 Ref. Para D Fitting (CONFIG 1) 116.40.06.112 Ref. Para D, Final Diameter Connecting Piece (CONFIG 2) 6232.0026.01 Ref. Pa ra D, Pre-Drilled Bearing Support (Left) (CONFIG 2) 6304.0023.01 Ref. ROM C hap 2 or SRM 51-00-03 Bearing Support (Right) (CONFIG 2) 6304.0023.02 Ref. ROM C hap 2 or SRM 51-00-03 Table 1 - Component Replacement Data

Pages 13–24 of 24