On this page
ADs that cite it · 1
Newest first, with the revision each names, as OpenAirDocs read it from the AD’s text: check it against the AD.
Text · 23Partly OCR
Some pages are OCR from a scan. OCR can misread letters and numbers. © Recaro. Filed by the FAA in regulations.gov docket FAA-2018-1019; AD 2019-08-01 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'f277be6c9143eb0ebd7abb5e7e9ab882ce1061967d1ee64ce6c23edd14e6ede0' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'f277be6c9143eb0ebd7abb5e7e9ab882ce1061967d1ee64ce6c23edd14e6ede0' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
RECARO RECARO Aircraft Seating GmbH & Co. KG • Daimlerstrasse 21 • 74523 Schwäbisch Hall • Germany • CAGE: C1084
SERVICE BULLETIN RECARO Aircraft Seating ATA Chapter: 25 Seat Type 3510A Series 377 and 381
EQUIPMENT/FURNISHINGS - PASSENGER SEATS - Exit Seat Pan Remove straps and replace seat pan assy Prepared by: J. Bohnacker on Plan May 20/2016 Customer Service Publications Checked by: P. Biernoth . P an Jul 06/16 Platforms Engineering Management Checked by: R. Hey Ca/AROL. O7 To 201.6 Certification/Airworthiness Office Approved by: R. Eitmann . 2 Juan. Yul 26 9, 2010 Technical Service Engineering Name Signature Date FV 7.3-04 Ind.01en ORIGINALLY ISSUED: May 20/2016 SB NO.: 3510-25-752 REVISION NO.: Page 1 of 22
RECARO Aircraft Seating GmbH & Co. KG • Daimlerstrasse 21 • 74523 Schwäbisch Hall • Germany • CAGE: C1084
SERVICE BULLETIN ORIGINALLY ISSUED: May 20/2016 SB NO.: 3510-25-752 REVISION NO.: Page 2 of 22
FV 7.3-04 Ind.01en
TABLE OF CONTENTS
ABBREVIATIONS4
1. PLANNING INFORMATION5
A. EFFECTIVITY5
B. CONCURRENT REQUIREMENTS7
C. REASON7
D. DESCRIPTION7
E. COMPLIANCE7
F. APPROVAL8
G. MANPOWER8
H. WEIGHT AND BALANCE9
I. ELECTRICAL LOAD DATA9
J. SOFTWARE ACCOMPLISHMENT SUMMARY9
K. REFERENCES9
L. OTHER PUBLICATIONS AFFECTED10
M. INTERCHANGEABILITY OR INTERMIXABILITY OF PARTS10
2. MATERIAL INFORMATION11
A. MATERIAL – PRICE AND AVAILABILITY11
B. INDUSTRY SUPPORT INFORMATION12
C. MATERIAL NECESSARY FOR EACH COMPONENT12
D. MATERIAL NECESSARY FOR EACH SPARE12
E. REIDENTIFIED PARTS12
F. TOOLING13
3. ACCOMPLISHMENT INSTRUCTIONS14
A. GENERAL14
B. DISASSEMBLY14
C. MODIFICATION14
D. ASSEMBLY17
E. RE-IDENTIFICATION18
F. TEST18
G. ACCOMPLISHMENT REPORTING19
RECARO Aircraft Seating GmbH & Co. KG • Daimlerstrasse 21 • 74523 Schwäbisch Hall • Germany • CAGE: C1084
SERVICE BULLETIN ORIGINALLY ISSUED: May 20/2016 SB NO.: 3510-25-752 REVISION NO.: Page 3 of 22
FV 7.3-04 Ind.01en
4. ILLUSTRATIONS20
TABLE OF FIGURES
Figure 1 Seat base with exit sheet straps20
Figure 2 Exit sheet assembly with strap21
Figure 3 Removal of existing seat bottom pan21
Figure 4 Installation of new seat bottom pan22
LIST OF TABLES
Table 1 Abbreviations4
Table 2 Affected Seat P/N (certified by Airbus)5
Table 3 Affected Seat P/N (not certified by Airbus)6
Table 4 Modification placard11
Table 5 Mod-Kit 3510MK752-0211
Table 6 Material required per TPL seat assembly12
RECARO Aircraft Seating GmbH & Co. KG • Daimlerstrasse 21 • 74523 Schwäbisch Hall • Germany • CAGE: C1084
SERVICE BULLETIN ORIGINALLY ISSUED: May 20/2016 SB NO.: 3510-25-752 REVISION NO.: Page 4 of 22
FV 7.3-04 Ind.01en
ABBREVIATIONS Table 1 Abbreviations A/C Aircraft AR As required (quantity indication) CMM Component Maintenance Manual CTR Center DBL Double DC Design Change DCP Design Change Proposal DDP Declaration of Design and Performance ESD Electrostatic discharge FIG Figure FR Front row HC Handicap locking mechanism on armrests IAT In-armrest table IFE In-flight entertainment IPL Illustrated Parts List (included in CMM for the affected seat series) LH Left-hand LOPA Layout of Passenger Accomodation LR Last row LRU Line Replaceable Unit MK Modification Kit MSDS Material Safety Data Sheet n/a Not applicable P/N Part number PDF Portable Document Format (a common file format for exchanging fixed-layout documents) QC Quick-change RAS RECARO Aircraft Seating RH Right-hand S/N Serial number S/S Shipset SB Service Bulletin STD Standard (seat version) STS Seat-to-seat (e.g. for power and data cables) SW Software TDS Technical Data Sheet TPL Triple
RECARO Aircraft Seating GmbH & Co. KG • Daimlerstrasse 21 • 74523 Schwäbisch Hall • Germany • CAGE: C1084
SERVICE BULLETIN ORIGINALLY ISSUED: May 20/2016 SB NO.: 3510-25-752 REVISION NO.: Page 5 of 22
FV 7.3-04 Ind.01en
1. PLANNING INFORMATION A. EFFECTIVITY This Service Bulletin is applicable to the RECARO Type 3510A seats of Series 377 and 381 which are listed in Sections (1) and (2) below.
NOTE: Refer to Section F on page 8 for applicable SB approval statements.
(1) Seat P/N certified by Airbus Table 2 Affected Seat P/N (certified by Airbus) Seat P/N (Pre-Modification) Modification (all seat places) Seat P/N (Post-Modification) Remove Exit Sheet Straps Replace Seat Bottom Pan Assy 3510A377-31-241 No Yes 3510A377-31-441 3510A377-31-243 No Yes 3510A377-31-443 3510A377-31-343 * Yes Yes 3510A377-31-251 No Yes 3510A377-31-451 3510A377-31-253 No Yes 3510A377-31-453 3510A377-31-353 * Yes Yes 3510A377-31-272 No Yes 3510A377-31-472 3510A377-31-372 * Yes Yes 3510A377-31-282 No Yes 3510A377-31-482 3510A377-31-382 * Yes Yes 3510A377-31-293 No Yes 3510A377-31-493 3510A377-31-303 No Yes 3510A377-31-503 3510A377-32-241 No Yes 3510A377-32-441 3510A377-32-243 No Yes 3510A377-32-443 3510A377-32-343 * Yes Yes 3510A377-32-251 No Yes 3510A377-32-451 3510A377-32-253 No Yes 3510A377-32-453 3510A377-32-353 * Yes Yes 3510A377-32-272 No Yes 3510A377-32-472 3510A377-32-372 * Yes Yes 3510A377-32-282 No Yes 3510A377-32-482 3510A377-32-382 * Yes Yes 3510A377-32-293 No Yes 3510A377-32-493
RECARO Aircraft Seating GmbH & Co. KG • Daimlerstrasse 21 • 74523 Schwäbisch Hall • Germany • CAGE: C1084
SERVICE BULLETIN ORIGINALLY ISSUED: May 20/2016 SB NO.: 3510-25-752 REVISION NO.: Page 6 of 22
FV 7.3-04 Ind.01en Seat P/N (Pre-Modification) Modification (all seat places) Seat P/N (Post-Modification) Remove Exit Sheet Straps Replace Seat Bottom Pan Assy 3510A377-32-303 No Yes 3510A377-32-503 3510A381-31-221 No Yes 3510A381-31-421 3510A381-31-321 * Yes Yes 3510A381-32-221 No Yes 3510A381-32-421 3510A381-32-321 * Yes Yes 3510A381-31-231 No Yes 3510A381-31-431 3510A381-31-331 * Yes Yes 3510A381-32-231 No Yes 3510A381-32-431 3510A381-32-331 * Yes Yes * Seat P/N marked with an asterisk (*) are post-implementation P/N of SB 3510-25-566 (“Exit Seat Pan Changes: Attachment with Plastic Tyrap”), created by modification of the seats with P/N written above.
SB 3510-25-566 shall no longer be implemented. Refer to 1.B “CONCURRENT REQUIREMENTS”.
(2) Seat P/N not certified by Airbus NOTE: The Seat P/N listed in Table 3 below are affected by this Service Bulletin but are not certified by Airbus.
NOTE: All Pre-Mod. Seat P/N listed in Table 3 are post-implementation P/N of SB 3510-25-566 (“Exit Seat Pan Changes: Attachment with Plastic Tyrap”), which shall no longer be implemented. Refer to Section 1.B “CONCURRENT REQUIREMENTS” below.
Table 3 Affected Seat P/N (not certified by Airbus) Seat P/N (Pre-Modification) Modification (all seat places) Seat P/N (Post-Modification) Remove Exit Sheet Straps Replace Seat Bottom Pan Assy 3510A377-31-351 Yes Yes 3510A377-31-451 3510A377-32-351 Yes Yes 3510A377-32-451 3510A377-31-341 Yes Yes 3510A377-31-441 3510A377-32-341 Yes Yes 3510A377-32-441 3510A377-31-393 Yes Yes 3510A377-31-493 3510A377-32-393 Yes Yes 3510A377-32-493 3510A377-31-403 Yes Yes 3510A377-31-503 3510A377-32-403 Yes Yes 3510A377-32-503
RECARO Aircraft Seating GmbH & Co. KG • Daimlerstrasse 21 • 74523 Schwäbisch Hall • Germany • CAGE: C1084
SERVICE BULLETIN ORIGINALLY ISSUED: May 20/2016 SB NO.: 3510-25-752 REVISION NO.: Page 7 of 22
FV 7.3-04 Ind.01en B. CONCURRENT REQUIREMENTS
(1) Please verify if the implementation of SB 3510-25-643 ("Fixation of Inner Beams") is pending for any of the seat assemblies listed in Section 1.A above.
Simultaneous accomplishment is strongly recommended in this case.
(2) Do NOT implement SB 3510-25-566 on any affected seat assembly if not yet accomplished.
NOTE: Service Bulletin 3510-25-566 will be invalidated. Exit Sheet Straps installed in accordance with SB 3510-25-566 will be removed during the implementation of this SB.
C. REASON RECARO type 3510 seats installed at a type III over-wing exit are subject to special requirements, e.g. in regards to evacuation of the aircraft. In order to fulfill these requirements, this Service Bulletin is due to be executed for all seat assemblies listed in Table 2 and Table 3 in Section 1.A “EFFECTIVITY”.
D. DESCRIPTION
(1) Although seats located at emergency exits are equipped with LH and RH exit sheets to support each seat bottom pan, RECARO decided to implement an additional exit sheet strap below the pan. Seat assemblies equipped with exit sheet straps are marked with “Yes” in column “Remove Exit Sheet Straps” of Table 2 and Table 3 in Section 1.A “EFFECTIVITY”. Because exit sheet straps may break in service in very limited cases, this Service Bulletin provides instructions to remove the straps, where currently installed.
(2) On all seat assemblies for which this SB is effective, regardless if previously equipped with exit sheet straps or not, the seat pan assemblies including the corresponding attachment packages are replaced with a different version.
E. COMPLIANCE The modification described in this Service Bulletin is highly recommended and shall be performed at the earliest opportunity when manpower and facilities are available.
RECARO Aircraft Seating GmbH & Co. KG • Daimlerstrasse 21 • 74523 Schwäbisch Hall • Germany • CAGE: C1084
SERVICE BULLETIN ORIGINALLY ISSUED: May 20/2016 SB NO.: 3510-25-752 REVISION NO.: Page 8 of 22
FV 7.3-04 Ind.01en F. APPROVAL The technical content of this document is approved under the authority of DOA ref.
EASA.21J.031.
NOTE: The preceding approval statement is only applicable for Seat P/N listed in Table 2 in Section 1.A(1) from page 5.
This document contains information and instructions which were produced according to alternative procedure of DOA AP110.
See EASA Approval No. EASA Approval No. EASA.21O.172 Rev. A.
Further airworthiness approvals may be required for aircraft installation purposes and are under the responsibility of the operator or installer to comply with.
G. MANPOWER NOTE: This Section provides estimates of the time required to do the work which is described in this Service Bulletin, in order to facilitate work planning. These estimates assume that the work will be done by experienced personnel and do not include the time to prepare, plan, or inspect the work. Time required for procurement of parts and tools, drying or curing time for paints, adhesives and cleaning agents, as well as general administration is also not included.
NOTE: Unsolicited reimbursement claims to RECARO for labor cost and/or related expenses will not be accepted, neither based on estimates in this SB nor in related documents. Written consent by RECARO, including the actual time and cost to be reimbursed, is always required per each claim prior to it being issued to RECARO. Please contact RECARO prior to implementing this SB for a confirmation of refundable expenses, if any are expected.
Approx. modification time per TPL seat assembly (average value):
(1) For seat assemblies equipped with Exit Sheet Straps (marked with “Yes” in column “Remove Exit Sheet Straps” of Table 2 or Table 3):
Method 1: Unrivet the blind rivets: 0.43 man-hours Method 2: Cut along the edges of the exit sheets: 0.35 man-hours
RECARO Aircraft Seating GmbH & Co. KG • Daimlerstrasse 21 • 74523 Schwäbisch Hall • Germany • CAGE: C1084
SERVICE BULLETIN ORIGINALLY ISSUED: May 20/2016 SB NO.: 3510-25-752 REVISION NO.: Page 9 of 22
FV 7.3-04 Ind.01en
(2) For seat assemblies without Exit Sheet Straps (marked with “No” in column “Remove Exit Sheet Straps” of Table 2 or Table 3):
Replacement of seat bottom pans only: 0.25 man-hours H. WEIGHT AND BALANCE
(1) For seat assemblies equipped with Exit Sheet Straps (marked with “Yes” in column “Remove Exit Sheet Straps” of Table 2 or Table 3):
Per TPL seat assembly (approx.): No change
(2) For seat assemblies without Exit Sheet Straps (marked with “No” in column “Remove Exit Sheet Straps” of Table 2 or Table 3):
Per TPL seat assembly (approx.): +0.105 kg (+0.231 lb.)
I. ELECTRICAL LOAD DATA n/a
J. SOFTWARE ACCOMPLISHMENT SUMMARY n/a
K. REFERENCES
(1) Aircraft Modification and Aircraft Service Bulletin This Service Bulletin is subject to aircraft modification N° 158410 K18421 (classified minor) and is covered by aircraft Service Bulletin N° A320-25-1BD7.
Under no circumstances shall the modified equipment, resulting from the application of this SB, be installed on the aircraft type unless its aircraft SB is approved.
NOTE: The preceding reference with accompanying statements is only applicable for Seat P/N listed in Table 2 in Section 1.A(1) from page 5.
RECARO Aircraft Seating GmbH & Co. KG • Daimlerstrasse 21 • 74523 Schwäbisch Hall • Germany • CAGE: C1084
SERVICE BULLETIN ORIGINALLY ISSUED: May 20/2016 SB NO.: 3510-25-752 REVISION NO.: Page 10 of 22
FV 7.3-04 Ind.01en
(2) COMPONENT MAINTENANCE MANUAL WITH IPL
RECARO AIRCRAFT SEATING TYPE 3510A / SERIES 377 ATA NO.: 25-25-69
(3) COMPONENT MAINTENANCE MANUAL WITH IPL
RECARO AIRCRAFT SEATING TYPE 3510A / SERIES 381 ATA NO.: 25-25-61
(4) DC No.: 0142-15
(5) SB 3510-25-566 (for Seat P/N marked with an asterisk in Table 2 on page 5, and all Seat P/N listed in Table 3 on page 6) L. OTHER PUBLICATIONS AFFECTED
(1) COMPONENT MAINTENANCE MANUAL WITH IPL
RECARO AIRCRAFT SEATING TYPE 3510A / SERIES 377 ATA NO.: 25-25-69
(2) COMPONENT MAINTENANCE MANUAL WITH IPL
RECARO AIRCRAFT SEATING TYPE 3510A / SERIES 381 ATA NO.: 25-25-61 M. INTERCHANGEABILITY OR INTERMIXABILITY OF PARTS
(1) For Seat P/N listed in Table 2 from page 5:
Refer to Aircraft Service Bulletin No. A320-25-1BD7.
NOTE: Some of the post-modification Seat P/N of seat assemblies listed in Table 3 are identical to a post-modification Seat P/N listed in Table 2.
(2) Modified seat assemblies may only be installed as defined in the applicable LOPA per each Seat P/N.
RECARO Aircraft Seating GmbH & Co. KG • Daimlerstrasse 21 • 74523 Schwäbisch Hall • Germany • CAGE: C1084
SERVICE BULLETIN ORIGINALLY ISSUED: May 20/2016 SB NO.: 3510-25-752 REVISION NO.: Page 11 of 22
FV 7.3-04 Ind.01en
2. MATERIAL INFORMATION A. MATERIAL – PRICE AND AVAILABILITY The following items are required to accomplish the modification.
NOTE: Please contact RECARO for detailed pricing and availability information.
(1) Modification Placard NOTE: One modification placard per seat assembly is required and must be ordered separately. Refer to Section 3.D(1) on page 17 for application.
Table 4 Modification placard RECARO P/N Description Qty. per Seat Assy 137-00-003-31 Placard (Modification) incl. Mylar cover 1
(2) Modification Kits Table 5 Mod-Kit 3510MK752-02 Modification Kit 3510MK752-02 (1 x per Seat Place = 3 x per TPL Seat Assy) Item P/N Description Qty.
10 139-00-242-10 Seat bottom assy 1 20 139-00-241-02 Spacer sleeve 4 30 * 045205AN Loop tape 50 light gray RKN102D050B 0.36 m 40 * 304-50-235-72 Loop tape self-adhesive, 50mm, beige, Klettostar 15244 0.11 m 50 104277 Clamp, ZEBRA B9MM-SW7 40-60 4 60 * 029254 Adhesive tape, Mercatape A 3700, 19mm 0.1 m * Adhesive tapes are available in packaging units of 50 m each.
RECARO Aircraft Seating GmbH & Co. KG • Daimlerstrasse 21 • 74523 Schwäbisch Hall • Germany • CAGE: C1084
SERVICE BULLETIN ORIGINALLY ISSUED: May 20/2016 SB NO.: 3510-25-752 REVISION NO.: Page 12 of 22
FV 7.3-04 Ind.01en B. INDUSTRY SUPPORT INFORMATION Inquiries concerning this Service Bulletin may be directed to:
RECARO Aircraft Seating GmbH & Co. KG Customer Service Technical Publications Daimlerstrasse 21 74523 Schwaebisch Hall
GERMANY Phone: +49 791 503 7855 Fax: +49 791 503 7935 Email: Service-Publications@recaro-as.com C. MATERIAL NECESSARY FOR EACH COMPONENT Table 6 Material required per TPL seat assembly RECARO P/N Description Qty. per TPL Seat Assy 137-00-003-31 Placard (Modification) incl. Mylar cover 1 3510MK752-02 Modification Kit 3 NOTE: Refer to Section 2.A from page 11 for Mod-Kit contents.
D. MATERIAL NECESSARY FOR EACH SPARE This SB is applicable for all seat assemblies listed in Section 1.A “EFFECTIVITY” regardless if these seats are in active service or being kept in stock as spare items.
E. REIDENTIFIED PARTS All modified seat assemblies receive new P/N. Refer to Table 2 from page 5 and Table 3 from page 6 for pre-modification vs. post-modification Seat P/N.
NOTE: Refer to Section 3.E “RE-IDENTIFICATION” on page 17 for re-identification of seat assemblies by application of the modification placard.