Copy · sb2000_22_008_00 · 42 pages

© Saab. Filed by the FAA in regulations.gov docket FAA-2018-1067; AD 2019-10-02 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Text

From the PDF’s text layer: layout, tables and figures are lost. The PDF is the document.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '7a4c6bd8770436f203e579059d20b7a47b099bcdb813c5eae9e5cdd9ac52a416'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Service Bulletin 15 June 2018

2000−22−008 Page 1 of 42 ATA CHAPTER: 22 AUTO FLIGHT − AUTO PILOT − MODIFICATION OF THE AUTO PILOT DISCONNECT LOGIC Mod No. 6566

1. PLANNING INFORMATION A. EFFECTIVITY

(1) Aircraft:

Aircraft Mfg. Serial No’s SAAB 2000 − 004 thru − 063.

NOTE: FOR A/C 004 −009 Service Bulletin SAAB 2000−91−001 must be included before this Service Bulletin.

(2) Spares: Not affected.

B. REASON Due to an inflight event causing a serious situation, the auto pilot disengage logic is modified to disengage the auto pilot when either of the two main pitch trim switches on each control wheel are operated.

C. DESCRIPTION This Service Bulletin gives instructions for:

− removal of relays − installation of new wires − Relocation of wires − installation of relays D. COMPLIANCE Mandatory.

Saab recommends this Service Bulletin to be performed within 24 months or 3000 FH, whichever comes first, from release of this Service Bulletin.

This Service Bulletin is under EASA consideration for an Airworthiness Directive.

The final compliance terms will be set by the EASA Airworthiness Directive (AD) when issued.

E. APPROVAL The technical content of this Service Bulletin is approved under the authority of DOA nr.

EASA.21J.066.

F. MANPOWER Estimated time to complete this Service Bulletin is:

1 person required.

Total manhours: 12 Elapsed time (hours): 12 Labour cost at operators expense.

Service Bulletin 15 June 2018

2000−22−008 Page 2 of 42 G. MATERIAL − COST AND AVAILABILITY Price and availability for Mod Kit. No. SAAB 2000−22−008−01 will be furnished on request.

H. TOOLING Air-data Test Set - Collins 970D-2A or equivalent Crimp tool Positioner Insert tool Removal tool Used for M22520/1−01 TH343 M81969/14−02 M81969/14−02 RSD20 GMT232 − − − S2420 I. WEIGHT AND BALANCE None.

J. ELECTRICAL LOAD DATA Not affected.

K. REFERENCES Aircraft Maintenance Manual (AMM) TASK 24−00−00−860−801 TASK 24−00−00−860−802 TASK 27−32−00−710−801 TASK 31−15−10−000−801 TASK 31−15−10−400−801 L. OTHER PUBLICATIONS AFFECTED Aircraft Maintenance Manual (AMM) Wiring Diagram Manual (WDM) System Schematics Manual (SSM) Aircraft Operations Manual (AOM)

2. ACCOMPLISHMENT INSTRUCTIONS A. JOB SET −UP

(1) Before you start the SB, make sure:

− The modification kit contains the parts listed in the Service Bulletin − The local supply items listed in the Service Bulletin are available − The documentation is available − The special tools are available.

B. REMOVAL

(1) Remove the following access panels.

− 117AL − 117AZ − 118AR − 220AZ

(2) Remove the relays (Ref AMM TASK 31−15−10−000−801).

Service Bulletin 15 June 2018

2000−22−008 Page 3 of 42 REF. FIG. 1

(a) In the LH electrical center 305VU, remove the relays:

− 35CC − 37CC FOR A/C 004−019

(b) In the RH electrical center 306VU, remove the relays:

− 34CC − 36CC − 16FD FOR A/C 020−063

(c) In the RH electrical center 306VU, remove the relays:

− 34CC − 36CC FOR A/C 004−019 C. MODIFICATION

(1) Wiring modification.

REF. FIG. 1, 2, 3, 5, 6

(a) In the LH electrical center 305VU, install the following new wire:

Wire No Class From Contact To Contact Remarks CC3000−24 A 35CC−J1:A2 RSD20 37CC−J1:B3 RSD20

(b) In the RH electrical center 306VU, relocate the following wire:

Wire No Class From Contact To Contact Remarks FD38−24 A 16FD−J1:X1 − 306VS−AP S2420 Connect together with wire CC3004

(c) In the RH electrical center 306VU, install the following new wires:

Wire No Class From Contact To Contact Remarks CC3002−24 A 34CC−J1:C3 RSD20 36CC−J1:C2 RSD20 FD3000−24 A 16FD−J1:X1 RSD20 34CC−J1:C2 RSD20

(d) Install the following new wires between the LH electrical center 305VU and RH electrical center 306VU:

Wire No Class From Contact To Contact Remarks CC3001−24 A 37CC−J1:B2 RSD20 36CC−J1:C3 RSD20 CC3004−24 A 35CC−J1:A3 RSD20 306VS−AP Connect together with wire FD38 FOR A/C 020−063 D. MODIFICATION

(1) Wiring modification.

Service Bulletin 15 June 2018

2000−22−008 Page 4 of 42 REF. FIG. 1, 4, 7

(a) In the LH electrical center 305VU, relocate the following wire:

Wire No Class From Contact To Contact Remarks CC726−24 A 305VS−HW − 305VS−PB S2420 Connect together with wire CC3000

(b) In the LH electrical center 305VU, install the following new wires:

Wire No Class From Contact To Contact Remarks CC3000−24 A 35CC−J1:A3 RSD20 305VS−PB Connect together with wire CC726 CC3001−24 A 35CC−J1:A2 RSD20 37CC−J1:B3 RSD20

(c) In the RH electrical center 306VU, install the following new wire:

Wire No Class From Contact To Contact Remarks CC3004−24 A 34CC−J1:C3 RSD20 36CC−J1:C2 RSD20

(d) Install the following new wires between the LH electrical center 305VU and RH electrical center 306VU:

Wire No Class From Contact To Contact Remarks CC3002−24 A 36CC−J1:C3 RSD20 37CC−J1:B2 RSD20 CC3005−24 A 34CC−J1:C2 RSD20 305VS−HW S2420 Connect together with wire FD435, FD436, FD437 FOR A/C 004−063 E. INSTALLATION

(1) Install the relays (Ref AMM TASK 31−15−10−400−801):

REF. FIG. 1

(a) In the LH electrical center 305VU, install the relays:

− 35CC − 37CC FOR A/C 004−019

(b) In the RH electrical center 306VU, install the relays:

− 34CC − 36CC − 16FD FOR A/C 020−063

(c) In the RH electrical center 306VU, install the relays:

− 34CC − 36CC

Service Bulletin 15 June 2018

2000−22−008 Page 5 of 42 FOR A/C 004−063 F. FUNCTIONAL TEST

(1) Connect the Air-data Test Set to the LH and the RH Air Data Computers (ADCs).

(2) Supply the External AC Power (Ref. AMM TASK 24−00−00−860−801)

(a) Supply the External AC Power (Ref. AMM TASK 24−00−00−860−801)

(b) On the overhead panel ELEC DC PWR (24VU), push in these pushswitches:

− L AVION − R AVION − ESS AVION

(3) For AHRS equipped aircraft, make sure the AHRS aligns.

(4) For IRS equipped aircraft, align the IRS.

(a) On the overhead panel EFIS SOURCE (65VU), make sure the EFIS SOURCE/IRS switch is set to NORM.

(b) On the overhead panel L WIPER/AVIONIC (47VU), set the IRS1/OFF/NAV/ATT switch to NAV.

(c) On the overhead panel R WIPER/AVIONIC (14VU), set the IRS2/OFF/NAV/ATT switch to NAV.

(5) On the ADS test set, increase the altitude until the LH and RH PFDs shows 5000ft.

(6) On the ADS test set, increase the Indicated Air Speed (IAS) until the LH and RH PFDs shows 120 knots.

(7) Do the functional test of the autopilot.

NOTE: You must not start this test until the AHRS/IRS aligns. Make sure the ATT/HDG ALIGNING - DO NOT TAXI message goes off and the normal attitude indicator is shown on both PFDs.

ACTION RESULT

(a) On the Flight Control Panel (FCP), turn the altitude preselect knob and set an altitude that is different from the aircraft altitude.

On the PFD, make sure the preselected altitude is not set to the aircraft altitude.

(b) Push the /C0065 1 2 /C0034 pushbutton and set it to the /C0065 (FD 1) position On the two PFD.s:

− The FD V bar is shown (On the DCP operate the FD pushbutton and make sure the FD V bar is not set to off) − The white AP <- legend is shown.

(c) Push the VS and the HDG pushbuttons.

On the FCP, the two indicators above the VS and the HDG pushbuttons come on.

On the PFDs, the green VS, the white ALTS and the green HDG legends are shown.

Service Bulletin 15 June 2018

2000−22−008 Page 6 of 42

ACTION RESULT

(d) Push each of the mode-select pushbuttons (but not the HALF BANK and the VNAV pushbuttons) in sequence and make sure the result is satisfactory before you continue.

The applicable legends are shown in the same sequence on the PFDs.

The indicators above the mode-select pushbuttons come on.

It is not possible to set more than one lateral and one vertical mode at the same time (although it is possible to do this with the modes that have arm logic).

A second push of the mode-select pushbutton does not cancel the mode (this shows the select logic operates correctly)

(e) Push the HALF BANK pushbutton two times.

The first push sets the half bank mode and the indicators above the HALF BANK pushbutton come on.

The second push cancels the half bank mode.

(f) Push the VNAV pushbutton two times The first push sets the VNAV mode and the indicators above the VNAV pushbutton come on.

On the PFDs, the NO VNAV legend is shown.

The second push cancels the VNAV mode.

(g) Turn the HDG/PUSH SYNC control to set the heading bug (shown on the PFDs) to 45/C0095 to the right.

On the PFDs, the FD V-bar shows the right bank command.

(h) Push the HDG/PUSH SYNC knob.

The heading shown with the heading bug and the aircraft heading align. The FD V-bar shows the wings level.

(i) Turn the HDG/PUSH SYNC control to set the heading bug to 45/C0095 to the left.

The FD V-bar shows the left bank command.

(j) Push the HDG/PUSH SYNC knob.

The heading shown with the heading bug and the aircraft heading align.

The FD V-bar shows the wings level command.

(k) Push the IAS/M pushbutton. The IAS mode legend is shown on the PFDs and the IAS and the aircraft speed align.

(l) Turn the IAS/M knob to decrease the IAS reference speed 20 knots.

The IAS reference speed decreases 20 knots.

The FD V-bar shows the up command.

Service Bulletin 15 June 2018

2000−22−008 Page 7 of 42

ACTION RESULT

(m) On the pilots control wheel, push the VERT SYNC pushbutton.

The IAS reference speed and the aircraft speed align. The FD V-bar shows the wings level.

(n) On the FCP, turn the IAS/M knob to increase the IAS/M reference speed 20 knots.

The IAS reference speed increases 20 knots.

The FD V-bar shows the down command.

(o) On the copilots control wheel, push the VERT SYNC pushbutton.

The IAS reference speed and the aircraft speed align. The FD V-bar shows the wings level.

(p) On the FCP, push the VS pushbutton.

The VS mode legend comes on and the VS reference is shown.

(q) Use the VS, /C0089 DN /C0066 UP, rocker switch and change the VS reference to show a 1000 feet per minute climb.

The VS reference changes and the FD V-bar show the up command.

(r) Use the /C0065 1 2 /C0034 pushbutton and set it to the /C0034 (FD 2) position.

There is no change to the VS mode legend and the VS The white AP -> legend is shown on the PFDs

(s) Use the VS, /C0089 DN /C0066 UP, rocker switch and change the VS reference to show a 1000 feet per minute descent.

The VS reference changes and the FD V-bar show the down command.

(t) Turn the ALTS PUSH/CANCEL control to set the preselected altitude to 6000 ft.

The preselected altitude of 6000 ft. is shown.

(u) Push the LVL CHG pushbutton. The CLIMB mode legend is shown on the PFDs.

(v) Push the ALT pushbutton. The ALT legend is shown on the PFDs.

(w) Turn the ALTS PUSH/CANCEL control to change the preselected altitude to 4000 ft.

The preselected altitude of 4000 ft. is shown on the PFDs.

(x) Push the LVL CHG pushbutton. The DESCENT mode legend is shown on the PFDs.

(y) On the Autopilot Panel (APP), turn the /C0089 DN /C0066 UP wheel to give a pitch up command.

The VS mode legend is shown on the PFDs.

The VS reference goes to a positive value in proportion to the quantity you move the /C0089 DN /C0066 UP wheel.

(z) On the Autopilot Panel (APP), turn the /C0089 DN /C0066 UP wheel forwards to give a pitch down command.

The VS reference goes to a negative value in proportion to the quantity you turn the /C0089 DN /C0066 UP wheel.

Service Bulletin 15 June 2018

2000−22−008 Page 8 of 42

ACTION RESULT (aa) On the ADS test set, decrease the Indicated Air Speed (IAS) until the LH and RH PFDs shows below 40 knots.

(ab) Pressurize the Hydraulic System with the Standby Pumps (Ref.

TASK 29-10-00-860-801) (ac) On the overhead panel TEST 3, set the L ELEVATOR and the R ELEVATOR switch to the top position to initialize the MBIT.

After 10 to 15 seconds, make sure that no warnings are shown for the Elevator Control System.

(ad) On the overhead panel TEST 2, momentarily operate the RUDDER switch to the top position to initialize the Rudder Control System PBIT test.

After 10 to 15 seconds, make sure that no warnings are shown for the Rudder Control System.

(ae) Lift the YD and the AP levers. The levers stay engaged and the green AP -> legend is shown on the PFDs.

(af) On the Autopilot Panel (APP), push the TURB pushbutton.

In the TURB pushbutton, the indicator light comes on.

(ag) Push the TURB pushbutton a second time.

In the TURB pushbutton, the indicator light goes off.

(ah) On the pilots control wheel, push the AP DISCONNECT pushbutton The autopilot disengages and the cavalry charge audio warning is heard.

The red AP -> legend is shown on the PFDs.

(ai) Push the AP DISCONNECT pushbutton a second time.

The cavalry charge audio warning stops.

The red AP -> legend changes to white.

(aj) On the APP, lift the AP lever. The autopilot engages.

(ak) On the copilots control wheel, push the AP DISCONNECT pushbutton The autopilot disengages and the cavalry charge audio warning is heard.

The red AP -> legend is shown on the PFDs.

(al) Push the AP DISCONNECT pushbutton a second time.

The cavalry charge audio warning stops.

The red AP -> legend changes to white.

(am)On the APP, lift the AP lever. The autopilot engages.

(an) On the control quadrant, on the aft of the LH POWER lever, push the go-around palm switch.

The autopilot disengages and the cavalry charge audio warning is heard.

On the PFDs, the GA mode legend is shown and the Flight Director (FD) shows the pitch up command.

(ao) Push the go-around palm switch a second time.

The cavalry charge audio warning stops.

Service Bulletin 15 June 2018

2000−22−008 Page 9 of 42

ACTION RESULT (ap) On the APP, lift the AP lever. The autopilot engages.

(aq) On the control quadrant, on the aft of the RH POWER lever, push the go-around palm switch.

The autopilot disengages and the cavalry charge audio warning is heard.

On the PFDs, the GA mode legend is shown and the Flight Director (FD) shows the pitch up command.

(ar) Push the go-around palm switch a second time.

The cavalry charge audio warning stops.

(as) On the APP, lift the AP lever. The autopilot engages.

(at) On the pilots control wheel, hold the two main pitch trim switches in the down position.

The autopilot disengages and the cavalry charge audio warning is heard.

(au) On the pilots control wheel, push the AP DISCONNECT pushbutton.

The cavalry charge audio warning goes off.

(av) On the APP, lift the AP lever. The autopilot engages.

(aw) On the pilots control wheel, hold the two main pitch trim switches in the up position.

The autopilot disengages and the cavalry charge audio warning is heard.

(ax) On the pilots control wheel, push the AP DISCONNECT pushbutton.

The cavalry charge audio warning goes off.

(ay) On the APP, lift the AP lever. The autopilot engages.

(az) On the copilots control wheel, hold the two main pitch trim switches in the down position.

The autopilot disengages and the cavalry charge audio warning is heard (ba) On the copilots control wheel, push the AP DISCONNECT pushbutton.

The cavalry charge audio warning goes off.

(bb) On the APP, lift the AP lever. The autopilot engages.

(bc) On the copilots control wheel, hold the two main pitch trim switches in the up position.

The autopilot disengages and the cavalry charge audio warning is heard (bd) On the copilots control wheel, push the AP DISCONNECT pushbutton.

The cavalry charge audio warning goes off.

(be) On the APP, lift the AP lever. The autopilot engages.

(bf) On the trim panel 45VU, operate the standby pitch trim switch in the two directions.

The autopilot disengages and the cavalry charge audio warning is heard (bg) On the APP, lift the AP lever. The autopilot engages.

Service Bulletin 15 June 2018

2000−22−008 Page 10 of 42

ACTION RESULT (bh) On the FCP, push the HDG pushbutton and try to move the pilots control column.

The autopilot holds the control column in position.

(bi) On the APP turn the /C0089 DN /C0066 UP wheel in different quantities forwards and then rearward.

The control column moves forwards and then rearward in proportion to the quantity you move the /C0089 DN /C0066 UP wheel.

(bj) Turn the L /C0065 /C0034 R knob to the left and to the right in different quantities.

The control wheel moves to the left and then to the right in proportion to the quantity you move the L /C0065 /C0034 R knob.

(bk) At the same time:

− Hold the control column in position − Turn the /C0089 DN /C0066 UP wheel forwards until the FD V-bar on the PFD shows a down command.

On the PFDs the yellow P legend comes on after approximately 5 seconds (this shows an elevator mistrim condition). On the Primary EICAS Display (PED), the amber AP PITCH MISTRIM legend comes on after approximately 10 seconds.

(bl) Release the control column.

(bm)At the same time:

− Hold the control column in position − Turn the /C0089 DN /C0066 UP wheel rearwards until the FD V-bar on the PFD shows the up command.

On the PFDs the yellow P legend comes on after approximately 5 seconds (this shows an elevator mistrim condition). On the Primary EICAS Display (PED), the amber AP PITCH MISTRIM legend comes on after approximately 10 seconds.

(bn) At the same time:

− Hold the control wheel in position − Turn the L /C0065 /C0034 R knob to the left until the FD V-bar on the PFD shows a left command.

On the PFDs the yellow R legend comes on after approximately 5 seconds (this shows an aileron mistrim condition). On the Primary EICAS Display (PED), the amber ROLL MISTRIM legend comes on after approximately 10 seconds.

(bo) At the same time:

− Hold the control wheel in position − Turn the L /C0065 /C0034 R knob to the right until the FD V-bar on the PFD shows a left command.

On the PFDs the yellow R legend comes on after approximately 5 seconds (this shows an aileron mistrim condition. On the Primary EICAS Display (PED), the amber ROLL MISTRIM legend comes on after approximately 10 seconds.

(bp) On the control wheel, push the AP DISCONNECT pushbutton.

The autopilot disengages and the cavalry charge audio warning is heard.

You can move the control wheel freely.

(bq) On the APP, lift the AP lever. The autopilot engages.

Service Bulletin 15 June 2018

2000−22−008 Page 11 of 42

ACTION RESULT (br) Turn the /C0089 DN /C0066 UP wheel until the FD V-bar on the PFDs shows a pitch up command.

The control column moves rearward.

On the Primary EICAS Display (PED), on the TRIM/ PITCH/UP/DN display, the pointers show a pitch up indication.

(bs) Turn the DN UP wheel until the FD V-bar on the PFDs show a pitch down command.

The control column moves forward.

On the Primary EICAS Display (PED), on the TRIM/ PITCH/UP/DN display, the pointers show a pitch down indication.

(bt) On the control wheel, push the AP DISCONNECT pushbutton.

The autopilot disengages and the cavalry charge audio warning is heard.

(bu) On the control wheel, push the AP DISCONNECT pushbutton a second time.

The cavalry charge audio warning goes off.

(bv) On the left main landing-gear, set the weight-on-wheels switch 5GA/S3 to the flight position.

(bw) On the APP, lift the YD lever.

(bx) On the overhead panel TEST 2, set the EFIS R switch to the top position.

(by) On the RH DCP, momentarily turn the FORMAT knob past the SEL position.

On the RH Multi-Function Display (MFD) the MAINTENANCE menu is shown.

(bz) On the RH DCP:

1 Use the VOR 2 or the ADF 2 pushbutton to move the cursor to the FCC DIAGNOSTIC line.

2 Push the RDR pushbutton to set the FCC DIAGNOSTIC page.

3 Rotate the format knob to the right until STOP while you push the RDR key in the DCP.

On the RH MFD the FCC DIAGNOSTIC PAGE is shown.

(ca) On the FCP:

− Use the /C0065 1 2 /C0034 pushbutton and set it to the /C0065 (FD 1) position − Push and hold three mode-select pushbuttons at the same time for a minimum of three seconds.

On the LH PFD the TEST legend is shown.

Service Bulletin 15 June 2018

2000−22−008 Page 12 of 42

ACTION RESULT (cb) Use the /C0065 1 2 /C0034 pushbutton and set it to the /C0034 (FD 2) position, and at the same time push and hold three mode-select pushbuttons for a minimum of three seconds.

On the RH PFD the TEST legend is shown.

(cc) Use the /C0065 1 2 /C0034 pushbutton and set it to the /C0065 (FD 1) position.

On the RH MFD the REPORT MODE diagnostic page is shown.

(cd) Push two mode-select pushbuttons at the same time and continue until the OUTPUT MODE diagnostic page is shown on the RH MFD.

The OUTPUT MODE diagnostic page is shown on the RH MFD.

(ce) Use the /C0065 1 2 /C0034 pushbutton and set it to the /C0034 (FD 2) position.

On the RH MFD the REPORT MODE diagnostic page is shown.

(cf) Push two mode-select pushbuttons at the same time and continue until the OUTPUT MODE diagnostic page is shown on the RH MFD.

The OUTPUT MODE diagnostic page is shown on the RH MFD.

(cg) Push one of the mode-select pushbuttons on the FCP to move the cursor below the first line of the output mode data.

The > symbol is on the top line.

(ch) On the APP, move the pitch knob to set RUDCMD on the top line of the MFD displays.

The RUDCMD text is shown on the top line and the RUDCMD value is 0.0.

The text below the MODIFY legend is BOTH (ci) On the EICAS Control Panel (ECP), push the FCS pushbutton.

On the Secondary EICAS Display (SED), the FCS page is shown.

(cj) On the APP, use the L /C0065 /C0034 R knob to change the RUDCMD value to + 5.0.

On the SED, on the FCS page, the rudder position is shown as - 5.0/C0095 plus or minus

1.0 /C0095.

(ck) Use the L /C0065 /C0034 R knob to increase the RUDCMD value to +10.0 /C0095.

The rudder position shown on the SED does not increase to more than - 5.0 /C0095.

(cl) Use the L /C0065 /C0034 R knob to change the RUDCMD to - 5.0 /C0095.

The rudder position moves to + 5.0 /C0095 plus or minus 1.0 /C0095.

(cm) Use the L /C0065 /C0034 R knob to change the RUDCMD value to -10 /C0095.

The rudder position shown on the SED does not increase to more than + 5.0 /C0095.

(cn) Use the L /C0065 /C0034 R knob to set the RUDCMD value to 0.0

Pages 13–24 of 42