TextPartly OCR
Some pages are OCR from a scan. OCR can misread letters and numbers.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'f72e0fbc19886f6c311fda588ab87b03292d932966e9a9f66b8c618282558e88' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = 'f72e0fbc19886f6c311fda588ab87b03292d932966e9a9f66b8c618282558e88' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
ALERT THIN Service Bulletin COMMANDER AIRCRAFT LLC 1176 Telecom Drive, Creedmoor, NC. 27522 Tel: (919)-956-4300 • Fax: (919)-682-3786 Service Bulletin 241 September 26, 2012
FUSELAGE ATTACHMENT TO WING MAIN SPAR - INSPECTION & REINFORCEMENT EFFECTIVITY: MODELS SERIAL NUMBERS 690 All (except S/N 11057) 690A All (except S/N 11104, 11106, 11129, 11134, 11146, 11159, 11173, 11192, 11220, 11237, 11252, 11263, 11280, 11287, 11298, 11303, 11317, 11339 & 11341) 690B All (except S/N 11383, 11384, 11401 & 11436) Note: Aircraft serial numbers configured with AVIADESIGN, Inc. STC No. SA5740NM are not compatible with the modifications contained in SB 241. These aircraft will require FAA approved Alternate Methods of Compliance or other approved methods to satisfy the structural intent of SB 241.
REASON FOR PUBLICATION:
Aircraft have been found with cracks in the outer fuselage frame attachment to the lower wing main spar at F.S. 178.81 vertical channel (310384-65 LH & -125 RH). Additional damage has been found at the upper picture window channel (310704-1 LH & -2 RH), shear clip (310412-23 LH & -24 RH), aft cabin pressure web (310384-159), external wing to fuselage fillet (110151-33 LH -34 RH) and working or sheared fasteners.
310384-193 F.S. F.S CHANNEL 310384-65 178.81 (REF.) CHANNEL 10736-4!
(REF.) CLIP (REF.
310736-91 ANGLE (REF.)
AUP F.S MAIN SPAR 126.00 INBD /D LOWER CAF (REF.) 178.81 F.S 31PP (R)
- 14.00, 310704-1 CHANNEL (REF.)
310384-159 WEB (REF) FIGURE #1 VIEW LOOKING AFT & OUTBOARD @ LH AFT PRESSURE
BULKHEAD / UPPER PICTURE WINDOW INTERSECTION
RH SIDE OPPOSITE, CABIN INNER FRAME
PANEL SKINS SHOWN REMOVED FOR CLARITY Page 1 of 20
SERVICE BULLETIN 241 Page 2 of 20 COMPLIANCE:
This Service Bulletin contains multiple initial compliance schedules based on the current airframe hours / time-inservice. Part I and II inspections / modifications are required before the expiration of the time period set forth in Table A applicable to the airplane; however it is highly recommended that Part I & II , inspections / modifications be accomplished at the earliest practicable time.
INITIAL COMPLIANCE SCHEDULE
CURRENT AIRFRAME (HOURS / TIME-IN-SERVICE)
COMPLIANCE REQUIRED PRIOR TO (HOURS / TIS) OR WITHIN THE NEXT [MONTHS] WHICHEVER COMES FIRST 0000 - 2000 2001 - 3000 3001 - 4000 4001 - 5000 5001 - 6000 6001 - 7000 Over 7000 (1000) Hours or [36] Months
(800) Hours or [36] Months
(650) Hours or [33] Months
(500) Hours or [30] Months
(350) Hours or [24] Months
(250) Hours or [18] Months
(150) Hours or [12] Months
- Table A -
Part I: ACCESS, DISASSEMBLY & INSPECTION OF THE FUSELAGE TO WING MAIN SPAR
ATTACHMENT JOINTS
Part I, Access, Disassembly & Inspections are accomplish ed to record material discrepancies (damage) in the fuselage to wing attachment area. Due to amount of man hours required to accomplish Part I, Part II is Mandatory. This will eliminate the requirement for futu re reoccurring inspections. The reinforcements designed and installed per this bulletin are terminating action.
Part II: MODIFICATION AND REASSEMBLY OF THE FU SELAGE TO WING MAIN SPAR ATTACHMENT JOINTS
This modification removes all the damaged or potential dama ged sheet metal parts in the area of the fuselage to wing main spar joint. This modification primarily replac es joint parts with improved heavier machined parts. The modification cuts and removes the upper 18.5-inc h section of the existing 310384-65/-125 channels and incorporates a heavier gage extruded channel as a replacement. The extruded channel was designed to nest into the lower remaining section of the existing channel. A vertical strap is cradled into the new frames making the joint Failsafe and provides improved fastener edge distan ce. Parts are being replaced for safety of flight to repair damage, prevent future damage and improve load paths.
BY WHOM WORK WILL BE ACCOMPLISHED:
A & P Mechanic (or Equivalent), and an ASNT Level II or III Certified NDT Inspector (or Equivalent) per INSPECTION REQUIREMENTS.
Due to the complexity of the work and potential to damage existing fuselage and wing structure during completion of the modification, it is mandatory that at least one member of the team accomplishing this task complete Twin Commander Aircraft approved training. Such training is available at the Factory Authorized Maintenance Training Provider.
NOTE:
IT IS RECOMMENDED THAT ALL MODIFI CATIONS BE COMPLETED ONLY AT AN AUTHORIZED TWIN COMMANDER SERVICE CENTER.
SERVICE BULLETIN 241 Page 3 of 20 APPROVAL:
Modifications described by this Service Bulletin are FAA DER Approved.
RELATED PUBLICATIONS:
SB 164 “INSPECTION AND REPLACEMENT OF WING SPAR FILLET SCREWS”. SB 241 incorporates applicable portions of the changes defined per SB 164.
SB 164 EFFECTIVITY: MODELS 690 (S/N 110 00 – 11079, except 11011, 11014, 11021, 11028, 11035, 11041, 11042, 11046, 11058, 11060, 11065, 11069 & 11074) 690A (S/N 11100 – 11344, except 11103, 11105, 11111, 11128, 11134, 11135, 11141, 11155, 11169, 11170, 11173, 11184, 11188, 11196, 11199, 11207, 11214, 11218, 11220, 11231, 11257, 11274, 11277, 11281, 11288, 11291, 11298, 11305, 11318, 11323, 11325 & 11329) 690B (S/N 11350 – 11566, exc ept 11338, 11355, 11366, 11406 & subs.)
SB 208A “INSPECTION FOR WING MAIN SPAR LOWER CAP CORROSION”. Highly recommend SB 208A and SB 241 be accomplished at the same time to reduce man hours . Both Service Bulletins require fuel cells and fuel cell liners are removed from the center wing fuel tanks.
SB 223 “WING LEADING EDGE ATTACHMENT INSPECTION AND MODIFICATION”. Recommend SB 223 and SB 241 are accomplished at the same time interval.
CK-144 “LOWER SPAR CAP REPLACEMENT PROCEDURE”. Highly recommend CK-144 per SB 208A, and SB 241 be accomplished at the same time interval to reduce overall man hours if deemed necessary. The wing lower main spar cap, replaced per SB 208A (CK-144), have fasteners that are common to both SB 208A and SB 241.
Both Service Bulletins require fuel cells and fuel cell liners are removed from the center wing fuel tanks.
SI-255 “PICTURE WINDOW UPPER CHAN NEL INSPECTION”. Aircraft previous ly configured with the improved 310704-3/-4 channels will not require replacement per SB 241.
SL-382 “SEALING CABIN LEAKS IN AIRCRAFT PRESS URIZED TO THE FLOOR”. Recommend SL-382 and SB 241 are accomplished at the same time interval.
ESTIMATED MAN HOURS: (Per Side - For Access, Inspection, Modification and Assembly)
Part I:
Access, Disassembly & Inspections LH Side 92 HRS R H S i d e 92 HRS Part II:
Modification & Reassembly LH Side 200 HRS R H S i d e 200 HRS
Parts required to comply with this Service Bulletin may be purchased through any TWIN COMMANDER FACTORY-AUTHORIZED SERVICE CENTER. Indicate SB 241, aircraft model and factory serial number when submitting order.
SERVICE BULLETIN 241 Page 4 of 20 PARTS DATA:
KIT SB241
Qty Part Number Description 1 K310384 (DWG) AFT PRESS. BLKHD - WING SPAR FRAME ATTACH REINFORCEMENT 1 310364-3 CHANNEL K310384-501 INSTL, LH 1 310364-4 CHANNEL K310384-502 INSTL, RH 1 310364-5 STRAP K310384-501 INSTL, LH 1 310364-6 STRAP K310384-502 INSTL, RH 1 310364-7 TEE K310384-501 INSTL, LH 1 310364-8 TEE K310384-502 INSTL, RH 1 310364-9 STRAP K310384-501 INSTL, LH 1 310364-10 STRAP K310384-502 INSTL, RH 2 310364-11 WEB K310384-501/-502 INSTL, L & RH 1 310704-3 CHANNEL K310384-501 INSTL, LH 1 310704-4 CHANNEL K310384-502 INSTL, RH 1 310736-45 CLIP K310384-501 INSTL, LH 1 310736-46 CLIP K310384-502 INSTL, RH 12 170468-5 SHIM K310384 (USE AS REQD.)
---------- -------------------------- -------------------------------- -------------------------------------------------------- ------- 2 310364-13 FILLER K310384-503/-504 INSTL, L & RH 2 310364-15 FILLER K310384-503/-504 INSTL, L & RH 1 310364-17 ANGLE K310384-503 INSTL, LH 1 310364-18 ANGLE K310384-504 INSTL, RH 2 310364-19 STRAP K310384-503/-504 INSTL, L & RH ---------- -------------------------- -------------------------------- -------------------------------------------------------- ------- 1 310364-21 DOUBLER K310384-505 INSTL, LH 1 310364-22 DOUBLER K310384-506 INSTL, RH 2 310364-23 ANGLE K310384-505/-506 INSTL, L & RH 1 310364-25 DOOR K310384-505 INSTL, LH 1 310364-26 DOOR K310384-506 INSTL, RH ---------- -------------------------- -------------------------------- -------------------------------------------------------- -------
ALL PER DWG HARDWARE
TO BE PROCURED LOCALLY: (as required)
1. MS20426AD4, AD5 & AD6 (BB) type rivets and MS20470AD4, AD5 & AD6 (BJ) type rivets.
2. NAS1097AD5 & AD6 (LZ) type rivets.
3. NAS1097E5 or KE5 type rivets.
4. CR3242-4 & -5 (ARD) type rivets and CR3243-4 & -5 (ARE) type rivets.
5. Epoxy primer used for touch up on parts furnished wi th the factory Modification Kits per MIL-PRF-23377, Type I, Class C.
6. PR-1440-C20 or PR O SEAL 890-C20 sealant per MIL-S-8802 / AMS-S-8802.
7. PolyGone 300-AG Gel (Aviation Grade Polysulfide Em ulsifier). High performance gel form designed to remove polysulfide and other sealants from a variety of surfaces. Follow manufactures recommendations for applicable uses of this product
8. Nashua 345, 3M 474 or Polyken 231, prem ium grade tape per ASTM D-5486 Type IV, Class 1.
CAUTION:
THE SUBSTITUTION OF BLIND RIVETS OTHER THAN THOSE INDICATED ON TWIN COMMANDER DWG NO. K310384 IN THE GENERAL NOTES OR ON THE FIELD OF DRAWING IS NOT PERMITTED
WITHOUT AUTHORIZATION FROM THE AIRFRAME MANUFACTURE OR APPROVED BY A REPRESENTATIVE OF THE FAA.
SERVICE BULLETIN 241 Page 5 of 20 RECOMMENDED TOOLS:
1. GO-NO-GO gages for HI-LOK fastener inspection.
2. Sheet metal tools needed for difficult access areas.
3. Cherry 269C3 selector gage for determining materi al thickness for installation of blind fasteners.
4. Cratex rub bloc k stick for cleaning and polishing fastener holes and metal surfaces.
SPECIAL TOOLS:
None
GENERAL INSPECTION CRITERIA:
TYPES OF INSPECTION FOUND IN THIS SERVICE BULLETIN ARE PER AC 43.13-1B CHAPTER 5 “NONDESTRUCTIVE INSPECTION” (NDI).
Perform FLUORESCENT DYE PENETRANT structural inspection as an aid in disclosing crack indications or other failures not detectable by visual means. Carefully remove sealant and / or finishes as necessary in order to allow inspection of the structural elements. Moderate hand pressure applied between parts, in order to produce any relative movement allowed, may assist in detection of failure of parts or joining fasteners. Also observe any rub marks indicating relative movement of parts under load.
Perform EDDY CURRENT structural inspection as an aid in disclosing subsurface crack indications or other failures not detectable by dye penetrant means. Fastener holes must be properly reamed before completing eddy current inspections, otherwise false results might be obtained.
Areas to be inspected are identified by Part Number and / or Name and are located per the applicable INSPECTION FIGURE(S).
NOTE:
ILLUSTRATED PARTS CATALOG MA Y BE USED FOR ASSISTANCE IN LOCATING INSPECTION AREAS (REFERENCE ONLY). INSPECTIONS A PPLY TO LEFT AND RIGHT HAND SIDES UNLESS OTHERWISE INDICATED. ONLY THE ODD NUMB ER PARTS AND ASSEMBLIES ARE REFERED TO IN THE FOLLOWING TEXT. EVEN NUMBERS ARE EQUAL APPLICABLE OPPOSITE PARTS.
SERVICE BULLETIN 241 Page 6 of 20 INSPECTION REQUIREMENTS:
1. PERSONNEL QUALIFICATION
a. NDI Level II or Level III.
b. Shall be qualified and certified in accordance wi th ASNT Personnel Qualifications SNT-TC-1A, ANSI / ASNT CP-189, NAS 410, or MIL-STD-410.
2. MATERIALS AND EQUIPMENT
a. Only materials listed or approved for listing per document QPL-AMS 2644 or QPL-25135 (Qualified Products List) shall be used for penetrant inspections. Cleaner, Penetrant and Developer to be from the same product manufacturer.
b. Solvent Removable Fluorescent Penetrant, per ASTM-E1417 or SAE-AMS 2644 sp ecifications, latest revision.
c. Solvent Remover (Class 1), per ASTM-E1417 or SAE-AMS 2644 specifications, latest revision.
d. Nonaqueous Develo per (Form D), per ASTM-E1417 or SAE-AMS 2644 specifications, latest revision.
e. Black Lights used for viewing & inspection must me et ASTM-E1417 specifications, calibrated per ANSI / NCSL Z540-1 or ISO 10012-1.
f. Inspection mirror.
3. CLASSIFICATION
a. Per ASTM-E1417 or SAE-AMS 2644 sp ecifications, latest revision.
b. Type 1 (Fluorescent Dye), Method C (Solv ent Removable), Sensitivity Level 3 (High).
c. Twin Commander Process Specification 130.17 “Eddy Cu rrent Flaw Detection in Aluminum Alloys”, latest revision.
SERVICE BULLETIN 241 Page 7 of 20 Part I - ACCESS, DISASSEMBLY & INSPECTIONS:
See the appropriate section of the airplane maintenance manual for procedures and instructions on removing and re-installing applicable items listed below.
1. Disconnect batteries.
2. De-fuel the airplane.
3. Shore the airplane at the wing jack pad (Item ) and tail tie down stand (Item ) per FIGURE #2 and level per Maintenance Manual instructions.
4. Complete shoring and leveling procedures as outlined per FIGURE #2 for (items &) to prevent movement of the fuselage and wing structure.
5. Remove the cabin interior (seating, side panels and head liner) components from (F.S. 126.00) aft to the pressure bulkhead web assembly located at (F.S. 178.81).
a. Take necessary measures required to protect elec trical and air-conditioning equipment on aft pressure bulkhead.
b. Protect and remove the left and right hand cabin picture window assemblies.
SERVICE BULLETIN 241 Page 8 of 20 Part I - ACCESS, DISASSEMBLY & INSPECTIONS: (continued)
6. Baggage compartment area (Center Wing Fuel Tanks):
a. Remove the baggage compartment forward and upper interior closeout panels as necessary to gain access to the aft side of the aft pressure bulkhead assembly and center wing fuel tanks.
b. Disconnect the center wing fuel tank fittings and sump. Unbolt the lower fuel tank removable floor structure. Remove the lower fuel tank cell. Optional to remove the aft and outboard lower fuel tank panels.
c. Remove the lower wing skin access door to gain ac cess to the center wing upper fuel tank. Disconnect and remove the upper fuel tank cell.
d. To gain access to the aft side of the wing main spar cap, remove the upper fuel tank liner panels. This will also allow access to fasteners being replaced common to the lower wing drag channel located inboard of W.S. 24.07.
e. Refer to K310384, Section G-G. Drill and remove t he six (per side) existing rivets attaching the lower wing skins to the lower wing drag channel.
CAUTION:
EXERCISE CAUTION WHEN REMOVING FASTENERS, DO NOT DRILL INTO THE MAIN SPAR LOWER CAP.
f. Remove and cleanup any old residual sealant and tape from the aft side of the main spar cap web assembly from (W.L. -1.64 to W.L. -12.18) and from (L.B.L. 15.00 & R.B.L. 15.00 outboard).
CAUTION:
AVOID THE USE OF TOOLS WHICH MAY CUT OR SCRATCH ALUMINUM SURFACES.
7. Inboard wing area (directl y outboard of W.S. 24.07):
a. Remove the upper wing fuel tank access doors (f orward and aft) of the main spar cap assembly.
b. Disconnect the inboard wing fuel tank fittings and re move or push back the fuel tank bladders to gain adequate access to the outboard side of the W.S. 24.07 rib.
c. Refer to K310384, Section G-G and Figure #3. Drill and remove the existing rivets attaching the lower wing to fuselage fillets fore and aft of F.S. 178. Caution: Do not remove existing rivets common to the W.S. 24.07 rib lower return flange (inboard flush row under fillet).
NOTE:
SOME AIRCRAFT MAY HAVE PRIOR INSTALLED REPAIRS OVER THE EXI STING LOWER WING TO FUSELAGE FILLET ANGLES. PRIOR REPAIRS MUST BE EVALUATED FOR THE AFFECTS ON COMPLIANCE WITH THIS SERVICE BULLETIN. CONTACT TWIN COMMANDER AIRCRAFT IN THE EVENT PRIOR REPAIR WILL NOT BE COMPLETELY REMOVED BY THIS BULLETIN.
d. Remove the four screws / Huck bolts common to the lower wing to fuselage fillet and main spar lower cap outboard of W.S. 24.07. If the aircraft has complied with SB 164, these fasteners may have already been changed. The original production version was MS27039 screws. These four (per side) existing fasteners must be removed to allow for additional modification parts.
SERVICE BULLETIN 241 Part I - ACCESS, DISASSEMBLY & INSPECTIONS: (continued)
e. Eddy Current inspect the existing fastener holes common to the main spar lower cap forward and aft flange per FIGURE #3. Prior to Eddy Current inspection, existing holes must be within limits indicated per Dwg No. K310384, General Note #8. Identify and record any damage found on the SB 241 Compliance Card. Provide photographs of the damage.
†. Fluorescent Dye Penetrant inspect the 110151-33 fillet radius 4.0-inch fore / aft of F.S. 178.81 per FIGURE #3 for crack indications. Note: Stop drill extreme ends of cracks with #40 drill (0.098 dia.) and rout along the fore / aft length of crack (0.098 dia.) after completion of Part I, Item #11. Stop drill holes and routed areas must maintain a minimum of 2 X fastener diameter (edge distance) from the center of existing fastener hole locations. If measured crack lengths are within limits, it is acceptable to proceed with the modifications per Dwg No. K310384-503 instl. If crack lengths exceed limits indicated or edge distance is below minimums, part must be removed and replaced with a new part or an approved repair must be installed prior to return to service. Identity and record any damage found on the SB 241
MAXIMUM ALLOWABLE CRACK LENGTH INSPECT FOR CRACKS 1.50-INCH EXTENDING FROM THE
ALONG FILLET RADIUS PT EXISTING FASTENER HOLE LOCATIONS ITEM #7, f. 6.00-INCH MAXIMUM OVERALL INSPECT MAIN SPAR LOWER CAP FWD / AFT FLANGE BOLT HOLES EC 6.00 (SEPARATE OR COMBINED LENGTH) FOR CRACKS (4 PLCS) MAX.
1.50 ITEM #7, e. MAX. 1.50 MAX. LOWER WING SKIN (REF.)
ITEM #7, c.
• ITEM #7, d 110151-33/-34 FILLET (REF.)
FUSELAGE SIDE F.S. STOP DRILL EXTREME CRACK ENDS AND ROUT SKIN (REF.) 178.81 CRACK LINE SMOOTH BETWEEN STOP DRILLS WITH A #40 DRILL (0.098 DIA.). PROTECT BACKUP UP FIGURE #3 STRUCTURE WITH STAINLESS STEEL SHIM STOCK BEFORE DRILLING OR ROUTING VIEW LOOKING UP & INBOARD @
FWD LH LOWER WING TO FUSELAGE FILLET
8. Aft fuselage compartment area (Picture Window):
a. Refer to K310384, Section A-A. Drill and remove the cabin inner skin structural panels and reinforcement gussets above the cabin picture window from F.S. 126.00 to F.S. 171.36.
CAUTION:
EXERCISE EXTREME CARE WHEN DRILLING I REMOVING EXISTING FASTENERS. DO NOT OVERSIZE OR DOUBLE DRILL EXISTING HOLES IN ATTACHING STRUCTURE.
b. Refer to K310384, Section A-A. Drill and remove the cabin inner skin structural panels and reinforcement gussets aft of the cabin picture window from (F.S. 172.50 to F.S. 178.81) from (W.L. -8.00 to W.L. -35.25).
NOTE:
THE CABIN FLOOR IS AT W.L. -55.50.
Page 9 of 20
SERVICE BULLETIN 241 Page 10 of 20 Part I - ACCESS, DISASSEMBLY & INSPECTIONS: (continued)
NOTE:
IF ANY OF THE CABIN INNER SKIN STRUCTURAL PANELS HAVE BEEN MODIFIED WITH
ADDITIONAL ACCESS HOLES OT HER THAN THE FACTORY RET URN FLANGED PARTS, THEY
MUST BE REMOVED AND REPLACED WITH NEW PA RTS OR AN APPROVED REPAIR MUST BE INSTALLED PRIOR TO RETURN TO SERVICE.
9. Refer to K310384, Section A-A. Remove the 310704-1 channel by removing the fastener row common to the lower wing to fuselage fillet from F.S. 126.00 to F.S. 178. 81. Remove the shear clips that attach the channel to the frames.
NOTE:
IF THE EXISTING 310704-1 UPPER PICTURE WI NDOW CHANNEL HAS BEEN PRIOR REMOVED AND REPLACED WITH THE IMPR OVED 310704-3 CHANNEL, THEY MAY BE LEFT IN PLACE WITH THE OPTION TO REMOVE AND REINSTALL.
a. Partial removal of the right side upper fuselage ice sh ield is required to access existing flush skin rivets attaching the upper picture window channel.
b. After removal of the existing picture window channels from the aircraft, remove and cleanup any old residual sealant left in place that may interfere with the new channel replacement.
c. Fluorescent Dye Penetra nt inspect the removed channels outboard flange, radius and web – complete length - for damage. Cracks have been found along t he outboard return flange (rivet hole to rivet hole) and along the parts lower web at areas common to the stub frame shear clip outboard attachment fasteners. Identify and record any damage found on the SB 241 Compliance Card. Provide photographs of the damage.
10. Refer to Figure 1. Remove the two horizontal pin and collar type fasteners attaching the 310412-23 shear clips. Note: During removal of these fasteners, inspect each fasteners pin / collar for working, tension or shear type damage. Identify and record any damage found on the SB 241 Compliance Card. Provide photographs of the damage.
11. Removal of the 310384-65/-125 channels and upper 310384-159 web.
a. Refer to K310384-501. Remove remaining fastener s (including the two .250-inch diameter bolts common to the upper and lower wing main spar caps) attaching the 310384-65/-125 channels web.
b. Refer to. K310384 Sect E-E. Remove fasteners from outboard fuselage skin below the wing to W.L.
-28.00. Remove and retain the shear clip attaching the existing lower picture window channel. Note: The W.L. -28.00 clip will be reinstalled later.
c. Refer to Figure 1. Remove and discard the 310736-45 shear clip attaching the upper picture window bulbed angle at W.L. -8.00 to the inboard flange leg of the 310384-65/-125 channels.
d. Refer to K310384-501. Remove fasteners (including the two .250-inch diameter bolts common to the upper and lower wing main spar caps) attaching the 310384-193 channels from (W.L. -1.64 to W.L.
-28.00). Remove all fasteners between the two vert ical wing support channels. Remove fasteners common to the lower fuel tank suppo rt structure and field fasteners attaching the 310384-159 web to the aft pressure bulkhead from (W.L. -1.64 to W.L. -28.00).
e. Refer to K310384-501. Determine the cut line (W.L -25.8 & L.B.L. 16.4) for the 310384-159 web. Insert stainless steel shim stock on the aft side of the 310384-159 web and aft attaching structure before cutting.
Cut and remove the indicated section of 310384-159 web and remove.
SERVICE BULLETIN 241 Part I - ACCESS, DISASSEMBLY & INSPECTIONS: (continued) Refer to K310384-501. Fluorescent Dye Penetrant inspect the 310384-159 web outboard edge between (W.L. -10.0 to W.L. -12.18) for damage. Identify and record any damage found on the SB 241 Compliance Card. Provide photographs of the damage.
g. Refer to K310384-501. Determine the approximate cut line (W.L -20.15 +/- .10) for the 310384-65/-125 channels. This location may vary slightly depending on the original fasteners location. Maintain a minimum of .36-inch edge distance from the channel cut line to the center of existing fastener hole locations. If necessary, the cut may be slightly angled to maintain these minimums. Additional material has been left on the replacement 310364-3 channels upper and lower ends to allow for vertical adjustment while locating the new parts.
h. Refer to K310384-501. After the cut locations have been marked, insert stainless steel shim stock on the outboard side (between the 310384-65/-125 channel and fuselage skin). Cut and remove the upper section of the -65/-125 channels.
i. Fluorescent Dye Penetrant inspect the removed 310384-65/-125 channels outboard flange, radius and web 4.0-inch above and below W.L. -12.18 for damage. Identify and record any damage found on the SB 241 Compliance Card. Provide photographs of the damage.
12. Main spar lower cap forward flange radius and upper and lower main spar .250-inch diameter bolt holes inspection:
a. Refer to Figure #4. Remove residual sealant from the local area (W.S. 24.07 / W.L. -12.18) to allow the radius of the spar forward flange to be cleaned and polished to a 32 RMS finish.
b. Fluorescent Dye Penetrant inspect .50-inch radius along the cutout of the forward flange at W.S. 24.07 on the main spar lower cap.
INSPECT MAIN SPAR UPPER & LOWER CAP INSPECT MAIN SPAR LOWER VERTICAL FLANGE AND SPAR WEB BOLT CAP FORWARD FLANGE .50-INCH HOLES FOR CRACKS (4 PLCS) RADIUS FOR CRACKS ITEM #12, f. ITEM #12, b.
MAIN SPAR WEB (REF.)
W.S. 24.07 RIB (REF.)
MAIN SPAR LOWER CAP (REF.) - 110151-33 FILLET (REF.)
W.L W.S.
-12.18 24.07
FUSELAGE SIDE 310420-9 CHANNEL - 310420-13 CLIP SKIN (REF.)
\ UP (REF.) (REF.)
FIGURE #4 VIEW LOOKING AFT & OUTBOARD @ LH INBD FWD FUSELAGE F.S. 178.81 / W.L. -12.18 / W.S. 24.07 VIEW SHOWN WITH 310384-65 CHANNEL, -159 WEB & 310704-1 UPPER PICTURE WINDOW CHANNEL REMOVED Page 11 of 20
SERVICE BULLETIN 241 Page 12 of 20 Part I - ACCESS, DISASSEMBLY & INSPECTIONS: (continued)
c. Refer to K310384 Section L-L. If a crack is detect ed in the main spar lower cap radius, contact Twin Commander Aircraft LLC. Aircraft is not to continue in service. If no cracks are found, check the main spar lower cap radius to be certain that machined transition area of the forward flange has a minimum radius of .50-inch and surface finish 32RMS or better. In addition, the lower main spar steel strap (.032- inch thick) also follows th is .50-inch radius trim common to the fo rward flange. Ensure the steel straps edge is flush with the spar radius trim. If the straps edge is not flush with the forward flange radius, trim flush with spar radius and provide surface finish 32 RMS or better at this location.
d. If the inspection reveals any deviation (except cracki ng), proceed as follows. Provide surface finish 32RMS or better to any rough areas, notches or machine marks in the radius area while maintaining a minimum radius of .50-inch and a surface finish of 32 RMS.
CAUTION:
MAINTAIN 2D EDGE DISTANCE ON ALL FASTENERS. DO NOT CUT INTO THE VERTICAL LEG OF THE MAIN SPAR LOWER CAP.
e. After the main spar lower cap radius has been inspected, restore sealant and finishes. Identify and record any damage found on the SB 241 Compliance Card. Provide photographs of the damage.
NOTE PRIOR TO EDDY CURRENT INSPEC TION OF EXISTING .250-INCH DIAMETER MAIN SPAR UPPER AND LOWER CAP HOLES, MUST REAMED WITHIN (.2659 /.2648 DIA).
f. Fluorescent Dye Penetrant inspect .250-inch diameter holes in the upper and lower main spar caps for cracks per FIGURE #4. If a crack is detected, contact Twin Co mmander Aircraft LLC. Aircraft is not to continue in service. Identify and record any damage found on the SB 241 Compliance Card.
13. Corrosion preventative measures an d sealants must be restored after inspections are completed. See part II, Item 12. NOTE.
14. Fill out information on the SB 241 Compliance Card and send to:
Twin Commander Aircraft LLC Attn.: Service Department 1176 Telecom Drive Creedmoor, NC. 27522
15. Part I, access, disassembly & inspections complete.