Copy · U.S. DOT/FAA - V2-0007 RevNC Final (2) · 6 pages

© Viking Air. Filed by the FAA in regulations.gov docket FAA-2015-0096; AD 2015-02-10 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Text

From the PDF’s text layer: layout, tables and figures are lost. The PDF is the document.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '25f289317f7ca309e114f8e209ccb822f2b230fb77826c4adebfee0a841d60f2'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

1959 deHavilland Way.

Sidney, B.C.

Canada V8L 5V5 Tel: (250) 656 - 7227

DHC-2 Beaver

29-April-2013 A.S.B. V2/0007 Revision ‘NC’ Page 1 of 6

ALERT SERVICE BULLETIN

ATA SYSTEM: 5510 NUMBER: V2/0007

I. PLANNING INFORMATION A. Effectivity Aircraft Affected: All DHC-2 aircraft.

NOTE: The instructions in this Service Bulletin are only applicable to the systems and parts installed at the time of delivery on the aircraft or as changed by Viking Service Bulletin(s). Before you do this bulletin, examine all STC or equivalent action changes to make sure this bulletin can be completed.

B. Reason A DHC-2 horizontal stabilizer attach bracket has been found with two (2) MS21042 locknuts broken. Upon further investigation, Viking has found a quality issue with the locknuts. (See Figure 3).

C. Description Some MS21042 Locknuts have been identified as being affected by a manufacturing issue, making them susceptible to premature failure due to cracking. This issue had previously been identified amongst other aircraft manufacturers and corrective action publications had been distributed. The fact that Viking has recently been supplied with a quantity of sub-quality locknuts, indicates that sub-quality parts continue to be available.

Due to the recent DHC-2 horizontal stabilizer bracket attach locknut issue, the following inspection / replacement shall be completed for all DHC-2 aircraft.

SUBJECT: INSPECTION AND/OR REPLACEMENT OF MS21042 LOCKNUT IN HORIZONTAL STABILIZER (P/N C2TP1A)

ALERT SERVICE BULLETIN V2/0007

29-April-2013 A.S.B. V2/0007 Revision ‘NC’ Page 2 of 6 D. Compliance All DHC-2 operators shall inspect their aircraft within 48 hours of receiving this Service Bulletin. If MS21042 locknuts are found, they must be replaced by MS21044 locknuts before further flight.

E. Approval The technical content of this Service Bulletin has been approved under the authority of Transport Canada Civil Aviation (TCCA) Design Approval Organization (DAO) 04-V-02.

F. Manpower Approximately 1 hour labour will be required to perform the inspection of the locknuts .

Approximately 12 hours is required if locknuts must be replaced with new ones.

NOTE: Visual inspection labour may be considerably more if stabilizer assembly must be removed to properly inspect locknuts.

G. Weight and Balance Not affected.

H. Electrical Load Data Not affected.

I. Publications Affected None.

J. References This Service Bulletin is self-contained. No additional drawing or documents are required to implement the Accomplishment Instructions.

Note: For more information please contact:

Viking Air Limited FAX: 250-656-0673 Technical Support Telephone Numbers:

1959 de Havilland Way Regional: 250-656-7227 Sidney, British Columbia North America: 1-866-49-ATLAS Canada, V8L 5V5 International: 1-800-6727-6727 technical.support@vikingair.com

ALERT SERVICE BULLETIN V2/0007

29-April-2013 A.S.B. V2/0007 Revision ‘NC’ Page 3 of 6

II. ACCOMPLISHMENT INSTRUCTIONS A. Preparing for Inspection

1. Remove tailcone section as per PSM 1-2-2 Sec. 2.16;

2. If visual inspection is impeded in any way, remove stabilizer assembly as per PSM 1- 2-2, Sec. 2.18.1.

B. Inspection Procedures

1. Using a flashlight, visually inspect quantity six (6) locknuts (as indicated in Figure 1) for type installed:

a) If the installed locknuts are NOT MS21042 (ref. Figure 2A, 2B, 2C for visual aid of possible locknuts installed in this application) skip to Step II. D;

b) If the installed locknuts are MS21042 (ref. Figure 2D for visual aid), continue to Step II. C.

C. Replacement of Affected Locknuts

1. Remove stabilizer assembly as per PSM 1-2-2, Sec. 2.18.1;

2. Remove affected locknuts;

NOTE: if locknut is completely missing, inspect area for pieces of broken locknut to eliminate Foreign Object Damage (FOD) potential.

3. Install new MS21044 locknuts (IAW para III. A. table) as per standard practices;

NOTE: Ensure a minimum of two (2) threads on the attach bolts are visible when the locknut is installed.

D. Close-Out

1. Re-install stabilizer assembly per PSM 1-2-2, Sec. 2.18.3;

2. Re-install tailcone as per PSM 1-2-2, Sec. 2.16.2.

3. Inform Viking Technical Support of any cracked locknut findings (See I.J.

References) E. Recording After completion of activities make the following entry in the aircraft log book: “Service Bulletin No. V2/0007 – INSPECTION OR INSPECTION/REPLACEMENT OF MS21042 LOCKNUT IN HORIZONTAL STABILIZER (P/N C2TP1A) has been incorporated”.

ALERT SERVICE BULLETIN V2/0007

29-April-2013 A.S.B. V2/0007 Revision ‘NC’ Page 4 of 6 III. MATERIAL INFORMATION AND TOOLING A. Material Information (Parts Required Per Aircraft) Old Part No. Replacement Part No.

MS21042-3 MS21044N3 MS21042-4 MS21044N4 B. Material Information None C. Tooling – Price and Availability  Standard aviation hand tools  Flashlight  Mirror

ALERT SERVICE BULLETIN V2/0007

29-April-2013 A.S.B. V2/0007 Revision ‘NC’ Page 5 of 6 IV. DRAWINGS AND TABLES

FIGURE 1 – MS21042 LOCKNUT LOCATION

LOCKNUT LOCATION

ALERT SERVICE BULLETIN V2/0007

29-April-2013 A.S.B. V2/0007 Revision ‘NC’ Page 6 of 6

FIGURE 2A – AN364 LOCKNUT FIGURE 2B – AN 365 LOCKNUT FIGURE 2C – MS21044 LOCKNUT

FIGURE 2D – MS21042 LOCKNUT (ALERT SERVICE BULLETIN SUBJECT)

FIGURE 3 – DISCREPANT MS21042 LOCKNUT