TextPartly OCR
Some pages are OCR from a scan. OCR can misread letters and numbers.
Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '489b20b7b24ff85c242d545d2d397f319e1e631e9b9ab97578746314b3721d22' ORDER BY p.page"
Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.
SELECT p.page, p.text_source, p.text, f.rights_holder, f.license FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256) WHERE p.file_sha256 = '489b20b7b24ff85c242d545d2d397f319e1e631e9b9ab97578746314b3721d22' ORDER BY p.page
Run it at the DuckDB prompt, or in any tool that reads Parquet over HTTPS. More ways to query the release are on Use the data.
Page 1 of 2 ATA Ref. 57-40 26-November-2019 Alert Service Bulletin V3/0011
REVISION TRANSMITTAL SHEET Inspection and Replacement of DHC-3 Wing Strut Assembly C3W100 Alert Service Bulletin No.: V3/0011 Date of Original Issue: 26 November 2019 Revision No: NC Date of Issue: 26 November 2019
This Alert Service Bulletin is issued for a one-time inspection of all DHC-3 wing strut assemblies C3W100.
This page transmits Revision ‘NC’ of Alert Service Bulletin V3/0011, pages 1 through 14, dated November 26, 2019.
Page 2 of 2 ATA Ref. 57-40 26-November-2019 Alert Service Bulletin V3/0011
THIS PAGE INTENTIONALLY LEFT BLANK
1959 de Havilland Way Sidney, B.C.
Canada V8L 5V5 Tel: (250) 656 - 7227
26-November-2019 A.S.B. V3/0011 Revision ‘NC’ Page 1 of 14 DHC-3 OTTER
ALERT SERVICE BULLETIN ATA SYSTEM: 57-40 NUMBER: V3/0011
I. PLANNING INFORMATION A. Effectivity This Alert Service Bulletin (ASB) is applicable to all DHC-3 aircraft equipped with wing strut assembly C3W100. This ASB applies to all dash numbers of the Strut C3W100 and all sub-assemblies.
B. Reason Viking Air Limited (Viking) has become aware of the failure of a C3W100 Wing Strut during operation. The failure mode is under investigation and appears to be in the area of the C3W104 lug plate. The investigation continues in order to assess the situation, but Viking recommends taking immediate safety action.
NOTE: Flights conducted above the original Type Certificate maximum gross weight of 8,000 lbs, will have an impact on DHC-3 strut life. Operators must follow Supplemental Type Certificate (STC) holder instructions for continuing airworthiness (ICA).
C. Description A Bolt Hole Eddy Current (BHEC) inspection of the lug hole on the lug plate C3W104, a visual and Fluorescent Dye Penetrant (FDP) inspection of the lug fitting C3W102 and C3W103, and a visual and Eddy Current Surface Scan (ECSS) inspection of the wing strut assembly C3W101 are specified in this ASB.
D. Compliance
1. For wing strut assembly C3W100 with 5,000 to 20,000 flight hours, perform a one-time inspection per Section II within 48 hours from the issue date of this ASB or, before next flight, whichever occurs later.
NOTE 1: No Wing Strut Assy C3W100, with more 20,000 flights hours shall be in service.
NOTE 2: In the case where, beyond the 48 hours, a ferry flight is required to go to the maintenance facility, contact Viking.
SUBJECT: Inspection and Replacement of DHC-3 Wing Strut Assembly C3W100
ALERT SERVICE BULLETIN V3/0011
26-November-2019 A.S.B. V3/0011 Revision ‘NC’ Page 2 of 14 NOTE 3: Whenever installing new or existing wing strut assembly C3W100, refer to Section II.E of this ASB for the required torqueing procedure to tighten the lug bolt nut and for application of Corrosion Preventive Compound, Type II (CPC) to all lug joints and all hardware.
a. If any crack is found or if the part is unserviceable due to corrosion or other damage, replace the existing wing strut assembly C3W100 per SB 3/10 and PSM 1-3-2, Appendix IV Part 6 before further flight, or contact Viking Technical Support for further instructions.
b. If no crack, corrosion or other damage is found, reinstall serviceable C3W100 strut.
2. For the wing strut assembly C3W100 with less than 5,000 flight hours, perform a one-time inspection per Section II, within seven (7) days from the issuing date of this ASB or, before next flight, whichever occurs later.
NOTE 1: Operators may contact Viking to inquire about alternative inspection requirements with proof of purchase and usage history records.
NOTE 2: In the case where, beyond the 48 hours, a ferry flight is required to go to the maintenance facility, contact Viking.
NOTE 3: Whenever installing new or existing wing strut assembly C3W100, refer to Section II.E of this ASB for the required torqueing procedure to tighten the lug bolt nut and for application of CPC to all lug joints and all hardware.
a. If any crack is found or if the part is unserviceable due to corrosion or other damage, replace the existing wing strut assembly C3W100 per SB 3/10 and PSM 1-3-2, Appendix IV Part 6 before further flight, or contact Viking Technical Support for further instructions.
b. If no crack, corrosion or other damage is found, reinstall serviceable C3W100 strut.
3. After completion of this ASB, return the Inspection Reply Form attached at end of this ASB to Viking Technical Support.
E. Approval The technical content of this ASB has been approved under the authority of Transport Canada Civil Aviation (TCCA) Design Approval Organization (DAO) 04-V-02.
F. Labour Requirements Estimated time to accomplish this ASB is 12 to 16 hours per strut.
G. Weight and Balance Not affected.
H. Electrical Load Data Not affected.
I. Publications Affected None
ALERT SERVICE BULLETIN V3/0011
26-November-2019 A.S.B. V3/0011 Revision ‘NC’ Page 3 of 14 J. References
1. SB 3/10, Fatigue of the DHC-3 Otter Flight Structures – Component Replacement Times;
2. PSM 1-3-2, DHC-3 Maintenance Manual;
3. PSM 1-3-5, DHC-3 Otter Supplemental Inspection and Corrosion Control Manual
4. SB 3/32, Main Pick-up Bolt Torque Loading – Special Inspection For more information please contact:
Viking Air Limited FAX: 403-295-8888 Technical Support Telephone Numbers:
7757 8th Street NE Regional: 587-430-0572 Calgary, Alberta North America: 1-800-663-8444 Canada, T2E 8A2 dh_technical.support@vikingair.com II. ACCOMPLISHMENT INSTRUCTIONS A. NDT (Non-Destructive Testing) Inspection of the Wing Strut Lug Plate C3W104
1. Inspection Procedure (Refer to Figure 1 and Figure 2)
(a) Refer to PSM 1-3-2, Part 2 Section 2.14. Securely support the LHS (Left Hand Side) and RHS (Right Hand Side) wings with suitable cradles inside a hanger.
Removal of the wing is unnecessary unless otherwise required.
NOTE: If available, dummy struts may be installed to secure the wings. This can eliminate wing removals if no hanger is available.
(b) Remove wing strut upper and lower fairings.
(c) Remove LHS and RHS wing strut assembly C3W100 (remove the wings as required).
NOTE: Refer to NOTE above for dummy struts.
(d) Remove the two (2) lug fittings C3W102 and C3W103, from each wing strut assembly C3W100.
(e) Remove the bushing C3W105 from each wing strut lug plate C3W104 (2 on each end of each strut, total 4). Mark or number the bushings and the corresponding lug holes to match their installation locations.
NOTE 1: To prevent damage to the lug plate and strut spar/skin, ensure that each lug plate is properly and securely supported and protected while pressing out or installing the bushing.
NOTE 2: CRC CANADA Freeze Spray or LOCTITE Freeze & Release, or equivalent may be used to ease the bushing removal and to prevent damage to hole bore: quickly spray to bushing ID for several seconds then immediately press out the bushing.
CAUTION: DO NOT HEAT UP THE LUG PLATE AND SKIN.
ALERT SERVICE BULLETIN V3/0011
26-November-2019 A.S.B. V3/0011 Revision ‘NC’ Page 4 of 14
(f) On each wing strut assembly C3W101, perform Bolt Hole Eddy Current (BHEC) inspection of the four (4) lug plate holes through all layers for crack or corrosion in accordance with Appendix A Section I.
2. If any crack or corrosion is found, replace the existing wing strut assembly C3W100 (next higher assembly of C3W101) per SB 3/10 and PSM 1-3-2, Appendix IV Part 6 before further flight, or contact Viking Technical Support for disposition. Refer to Section II.E of this ASB for the required torque to tighten the lug bolt nut and for application of CPC to all lug joints and all hardware.
NOTE: If the existing LHS or RHS or both wing strut assemblies C3W100 (next higher assembly of C3W101) are to be replaced per SB 3/10 and PSM 1-3-2, Appendix IV Part 6, the remaining inspections specified in Section II.B to II.D can be ignored for LHS or RHS or both sides as applicable.
3. If no crack is found:
(a) On each wing strut assembly C3W101: check the lug plate hole bore condition (surface roughness shall be RA 125 or better, free of gouges, scratches, scores or similar imperfections). Measure and record the Inner Diameter (ID) using a suitable hole bore gauge or internal micrometer, which shall be between 0.8745” and
0.8755”.
(b) On each wing strut assembly C3W101: check inner and outer surface plating condition of the four (4) bushings C3W105 removed in Step II.A.1.(e). Measure and record the Outer Diameter (OD) and ID (using a suitable hole bore gauge or internal micrometer). The OD shall be 0.8755”-0.8760”. The ID shall be
0.7495”-0.7505”.
NOTE: New bushings C3W105-3 are highly recommended because the surface finish on existing bushing may likely be damaged. Step II.A.3.(b) is not required when existing bushings are replaced.
(c) If the lug hole bore and bushing surface conditions (including cadmium plating) are serviceable with proper diameters as measured in previous Step, wet-reinstall the existing bushings back to their original locations (as marked in Step II.A.1.(e) with structural sealant PS 870 Class A conforming to MIL-PRF-81733 or AMS 3265 (refer to PSM 1-3-5 Part 1, Paragraph 6.D), using shrink fit technique. Or, wet-install new C3W105-3 bushings as required (refer to the Note (1) in Table 1 below for pre-reaming of the bushing ID prior to installation).
NOTE 1: Diestone DS 108, Diestone DLS, Diestone HFP or equivalent is used for general solvent cleaning process. Solvent clean the lug hole bore. Solvent cleaning the bushings may use dampened wiping cloths (or a quick-short emersion method: remove the bushing out from solvent as soon as grease/oil/dirt is dissolved). Wipe away any remaining solvent with a clean dry cloth.
NOTE 2: Solvent clean the hole bore and wipe away any remaining solvent with a clean dry cloth. Apply Alodine Class 1A solution MIL-DTL-81706 to bare metal as required (where original anodized subface finish is damaged).
NOTE 3: Solvent clean the hole bore and wipe away any remaining solvent with a clean dry cloth. Apply a thin layer of sealant into hole bore prior to installing the bushing. After installation, seal the bushing edges as shown in Figure 3 and remove excessive sealant as required.
ALERT SERVICE BULLETIN V3/0011
26-November-2019 A.S.B. V3/0011 Revision ‘NC’ Page 5 of 14 NOTE 4: After solvent cleaning, cool bushings with liquid nitrogen to contract the diameter. The handling tongs or installation tools are to be chilled along with the bushing.
CAUTION: DO NOT HEAT UP THE LUG PLATE AND SKIN.
(d) If the lug hole bore is out of tolerance, oversized bushings as listed in Table 1 below shall be wet-installed with structural sealant PS 870 Class A conforming to MIL-PRF-81733 or AMS 3265 (refer to PSM 1-3-5, Part 1 Paragraph 6.D), using shrink fit technique. Ream the lug holes accordingly per Table 1. The 0.010” oversized bushings shall be used first unless other oversized bushing is required due to the hole quality.
Refer to NOTE 1 to NOTE 4 in previous Step for bushing installation.
The oversized bushing may be slightly longer than the total thickness of the lug plate and the two layers of the strut skins. It shall be installed with one end surface flush with the inner-free surface of the lug plate C3W104, and machine the outer end surface flush the skin as required (do not damage the skin surface). Solvent clean the machined surface and wipe away with a clean dry cloth. Apply Epoxy Primer. Contact Viking Technical Support for detailed disposition.
NOTE 1: The oversized bushings and lug hole sizes are listed in Table 1 below.
Table 1. Oversized Bushings and Lug Hole Sizes Bushing Part No.
Bushing ID(1) Bushing OD Lug Hole ID Note C3W107-5 23/32” 0.8855”-0.8860” 0.8845”-0.8855” 0.010” Oversize C3W107-7 23/32” 0.8955”-0.8960” 0.8945”-0.8955” 0.020” Oversize C3W107-9 23/32” 0.9055”-0.9060” 0.9045”-0.9055” 0.030” Oversize
(1) Prior to bushing installation, ream bushing ID to 0.7400” (or 0.7395”-0.7405”) and protect the ID immediately to prevent rusting. This is to prevent bushing from spinning during the final reaming. After the installation of the bushings, line-ream the bushing ID to 0.7495”-0.7505” at each end of the strut (protect the reamed ID immediately to prevent rusting).
NOTE 2: An adjustable reamer may be required to line-ream the lug holes (and the bushing ID) to the required sizes. Prior to the reaming process, verify the reamed hole size on a piece of dummy material (same/similar material as the part) before reaming the actual part.
NOTE 3: Prior to the final reaming process, ensure that the hole bore of the bushing ID at each end of the strut is properly aligned and squared to lug plate surface.
B. Visual and NDT Inspection of the Wing Strut Lug Fittings C3W102 and C3W103
1. On each wing strut assembly C3W100: thoroughly clean the two (2) lug fittings C3W102 and C3W103 (total 4 on 2 wing strut assemblies C3W100).
2. Perform a general visual inspection of each lug fitting for corrosion, dent, wear or other damage, using a strong light and minimum 10X magnifying glass, as required.
ALERT SERVICE BULLETIN V3/0011
26-November-2019 A.S.B. V3/0011 Revision ‘NC’ Page 6 of 14
3. Perform Fluorescent Dye Penetrant (FDP) inspection of each lug fitting C3W102 and C3W103 for cracking at the lug holes (near/around the bushing OD) and the transition radii, in accordance with Appendix B.
4. If any damage is found, repair or replace as required, or contact Viking Technical Support for detailed disposition.
5. If no damage is found, reapply surface finishes on each lug fitting for reinstallation:
apply Alodine Class 1A solution MIL-DTL-81706 to bare metal as required (where original anodized surface finish is damaged), plus one coat of Epoxy Primer (masking the bushing ID). Two coats of Epoxy Primer are preferred if there is no interference in following the fitments:
• between the lug fitting (C3W102, C3W103) and strut lug plates C3W104;
• between the lug fittings (C3W102) and the lug on the wing;
• between the lug fittings (C3W103) and the lug on the fuselage Tie Bar.
C. Detailed Visual Inspection and NDT Inspection of the Wing Strut C3W101
1. On each wing strut assembly C3W101: thoroughly clean the external and internal surfaces along the entire length of the strut.
2. Perform a detailed visual inspection of the external surface of each strut for cracks or corrosion or other damage, using a strong light and minimum 10X magnifying glass.
Pay particular attention to following areas for cracking:
(a) The joint area between the lug plate (C3W104) and the strut skin for cracks on the skin around fastener heads (refer to Figure 2).
(b) Around fastener head on the skin at/near the lightening hole centres (on the strut spar web).
3. Perform ECSS inspection of the external surface of each strut around fastener heads (common to the two flanges of the strut spar) for cracking on the strut skin in accordance with Appendix A Section II.
4. Perform detailed visual inspection of the internal surfaces of each strut along the entire length for cracking or corrosion or other damage, using a borescope with strong light source. Pay particular attention to following areas for cracking:
NOTE: A borescope with 5.5 feet long flexible tube between the eyepiece and the display is recommended to cover the entire length of the strut internal surfaces. The eyepiece side may be fixed to a stiff and light rod to ease the access.
(a) Strut spar web at lightening holes (refer to Figure 2);
(b) Strut spar web at the end row of fastener hole (inner end of spar web reinforcement plates C3W101-5, refer to Figure 2);
(c) Strut spar flange around fastener heads near/at the lightening hole centres (lateral cracks); strut spar flange along the bending radii (longitudinal cracks).
(d) The lug plate edge at the end row of fastener holes (outer end of the strut spar, refer to Figure 2).
5. If any damage is found, repair or replace as required, or contact Viking Technical Support for detailed disposition.
ALERT SERVICE BULLETIN V3/0011
26-November-2019 A.S.B. V3/0011 Revision ‘NC’ Page 7 of 14
6. If no damage is found, touch up the surface finishes on the strut external and internal surface as required. Touch up corrosion protection of the internal surface per PSM 1-3-5.
D. General Visual Inspection of the Wing Strut Attachment Hardware
1. Thoroughly clean all wing strut attachment hardware (bolts, washers and nuts).
2. Perform detailed visual inspection of each hardware for condition, using a strong light and minimum 10X magnifying glass. Pay particular attention to each bolt for cracking or corrosion or other damage.
3. Replace damaged hardware as required (refer to NOTE 1 below).
E. Close Out NOTE 1: Prior to assembly, clean all bushing IDs (including the lug holes on the wing and on the fuselage Tie Bar) (such as Diestone DS 108, Diestone DLS, Diestone HFP, or equivalent). Wipe away any remaining solvent with a clean dry cloth.
Also clean the lug surfaces on the wing and on the fuselage Tie Bar and perform visual inspection for condition (rectify discrepancy, as required) prior to strut installation.
NOTE 2: Apply a thin layer of non-drying jointing compound (CorBan 27L, CA 1000, or similar) to all bushing IDs and bolt shanks.
1. Reinstall serviceable lug fittings C3W102 and C3W103 to each wing strut assembly C3W100.
2. Reinstall LHS and RHS wing strut assembly C3W100 (refer to SB 3/32 for the required torqueing procedure to tighten the lug bolt nut). Apply CPC to all lug joints including all hardware and ensure all lug gaps are filled. Refer to PSM 1-3-5, Part 1, Paragraph 7 for more information.
NOTE 1: Whenever new wing struts C3W100 are installed, new attachment bolts shall be used:
• C3W128-3 (Pre-Mod 3/1010) or C3W128-5/-9 (Post Mod 3/1010) Bolt, Special upper attachment, QTY (Quantity) 1 per strut.
• C3W129-3 (Pre-Mod 3/1010) or C3W129-5/-9 (Post Mod 3/1010) Bolt, Special lower attachment, QTY 1 per strut.
NOTE 2: Follow PSM 1-3-2, Part 2 Section 2.14 to reinstall wings, if removed and rigging control surfaces per applicable Sections in PSM 1-3-2, as required.
3. Reinstall wing strut upper and lower fairings, LHS and RHS.
4. Remove wing supports as applicable.
F. Recording After completion of this Service Bulletin, make the following entry in the aircraft log book:
“Alert Service Bulletin No. V3/0011 Revision ‘NC’ – Inspection of DHC-3 Wing Strut Assembly C3W100 has been incorporated”.
ALERT SERVICE BULLETIN V3/0011
26-November-2019 A.S.B. V3/0011 Revision ‘NC’ Page 8 of 14 III. MATERIAL INFORMATION AND TOOLING A. Material Information C3W105-3 Bushing, Wing Strut, QTY 4 per Strut Strut Attachment Bushings - oversized:
• C3W107-5, Bushing, 0.010” Oversize, AR (as required).
• C3W107-7, Bushing, 0.020” Oversize, AR.
• C3W107-9, Bushing, 0.030” Oversize, AR.
NOTE: Oversize bushings can be purchased individually or in custom quantities. Multiple sizes and quantities are recommended for unexpected errors that may occur during the bushing installation process.
B. Special Tools and Equipment Required Eddy Current and Fluorescent Penetrant non-destructive testing equipment is commercially available.
1. The fastener hole inspection requires the following equipment:
• Hocking Phasec 2200, Eddy Current Instrument, Impedance−Plane Type, or equivalent
• Hocking 33A100, Mini Drive Unit, or equivalent
• Hocking 33A103, Cable−Mini Drive Unit, or equivalent
• Calibration Reference Standard, Techna NDT RH12-T40-7075T6 or RH20-T40-7075T6, or equivalent
• Techna NDT HRY 0.750-0.875, rotating bolt hole probe, 100 kHz − 2.0 MHz frequency, 0.125 to 0.156−inch adjustable diameter, 2.0−inch length, or equivalent.
Alternative: Techna NDT HRY 0.875-1.0, rotating bolt hole probe, 100 kHz − 2.0 MHz frequency, 0.875 to 1.0-inch adjustable diameter, 2.0−inch length, or equivalent.
2. The Eddy Current surface scan inspection requires the following equipment:
• Hocking Phasec 2200, Eddy Current Instrument, Impedance−Plane Type, or equivalent.
• Coaxial cable, BNC to Microdot.
• Calibration Reference Standard AL29−32, or equivalent.
• Techna NDT PEN45−6, 45° Surface probe, 50 kHz to 500 kHz frequency, Fe/NFe, absolute, shielded, 0.125−in. (3.175−mm) diameter, 6.0−in. (152.4−mm) length, 0.500−in (12.7 mm) drop, or equivalent.
3. Fluorescent Dye Penetrant inspection requires the following equipment:
• MAGNAFLUX MODEL ZB-24A, PN 513721 Black Light Inspection Lamp, or equivalent with minimum power rating 100 watts, intensity of 1200 microwatts per cm2 at 15 inches (38.1 cm).
• Ultra Violet Products Inc. Model J-221 Black Light Intensity Meter, or equivalent.
ALERT SERVICE BULLETIN V3/0011
26-November-2019 A.S.B. V3/0011 Revision ‘NC’ Page 9 of 14
• Light meter, suitable for testing ambient white light intensity.
• Cellulose sponge or nylon brush.
• Cloths, clean, lint-free.
• AMS 2644, MIL-I-25135, Fluorescent dye penetrant, Method C, Type I.
sensitivity level 3 or greater.
• QPL AMS 2644, Developer, Form d, nonaqueous.
• QPL AMS 2644, Solvent remover, non-halogenated, Class 2.
• TURCO 5351, (BONDERITE S-ST 5351 AERO), or equivalent, Paint remover, stripper.
• Diestone DS 108, Diestone DLS, Diestone HFP, ASTM-D740 (MEK), or equivalent, Solvent, general cleaning.
• Tape, masking, lead or plastic
4. Detailed visual inspection tools:
• A borescope with strong light source
• A strong light.
• minimum 10X magnifying glass.
• Mirror.
ALERT SERVICE BULLETIN V3/0011 Faring Assembly C3W141 Lug Fitting C3W102 Bolt C3W114-3/-5/-9 Lug Plate Bolt C3W 128-3/-5/-9 C3W104 Bushing C3W105-3, QTY 2 (or Bushing C3W107-5) Strut Spar C3W101-4 (or Bushing C3W107-7) (or Bushing C3W107-9) Strut Assembly C3W100, including:
• Strut Assembly C3W101
• Lug Fittings C3W102 and C3W103 Bolt C3W114-3/-5/-9 • Bolt C3W114-3/-5/-9 Strut Assembly C3W101, excluding:
• Lug Fittings C3W102 and C3W103
• Bolt C3W114-3/-5/-9 Bolt C3W 129-3/-5/-9 Bushing C3W105-3, QTY 2 (or Bushing C3W107-5) (or Bushing C3W107-7) (or Bushing C3W107-9) Lug Fitting C3W103 Faring Assembly C3W140 Figure 1. DHC-3 Wing Strut Assembly C3W100 26-November-2019 A.S.B. V3/0011 Revision 'NC' Page 10 of 14