(MANUAL IDENTIFICATION)
THIS PAGE INTENTIONALLY LEFT BLANK REVISION:
Revision 3 (DATE) Page 2 Page Apdx A - 61
AC 29-2C, Chg 1 2/12/03 (MANUAL IDENTIFICATION) ATTACHMENT 4
TYPE DESIGN CHANGE
ICA RECOMMENDED PROCEDURES The following information is intended for guidance to assist the applicant in preparing an ICA.
For this sample, we will use a twidget, which is a sounder attached to an extendible cable assembly connected to a pivoting arm, which is mounted to the side of the fuselage structure at the right cabin door forward frame.
NOTE: The twidget manufacturer's ICA does not meet the requirements of Appendix A and cannot be referenced.
The following step-by-step procedure in this sample can be used to prepare an ICA for that appliance:
1. Determine the following:
a. What modifications to the rotorcraft will be required.
b. Determine what appliances will be replaced or added to the rotorcraft.
c. Determine which ATA chapters of the original rotorcraft manufacturer's maintenance manual will be affected by this TDC and which additional ATA chapters will be affected.
2. Review Appendix A, Part 29. Using the information derived in paragraph 1, determine which paragraphs are applicable and which are not applicable. As defined in Figure 2, provide the status of each requirement on the applicable paragraph. If the requirement is not applicable, place an N/A within the parentheses ( ). Address the remaining requirements in the ICA. A completed document for the twidget installation (see Figure 2) is included.
3. Prepare the ICA, which includes the applicable requirements specified in Appendix A to Part 29. This can be done by using the information provided in the Instructions for Continued Airworthiness Template. The regulatory requirements in the sample manual are in bold type.
Information to be copied is in normal type. Information in italics is for information only and should not be copied. See Instructions for Continued Airworthiness sample manual.
4. Ensure that the ICA includes the following:
a. A Cover Page, which will readily identify the publication as the applicant's ICA for that make and model rotorcraft.
b. A List of Effective Pages, which lists each page in the ICA and its revision number and revision date.
c. A Record of Revisions Page for listing the revisions which have been inserted in the ICA.
REVISION: (DATE) Revision 3 Page 1 Page Apdx A - 62
(MANUAL IDENTIFICATION) ATTACHMENT 4
TYPE DESIGN CHANGE
ICA RECOMMENDED PROCEDURES (Continued)
5. Table of Contents is not required, but we recommend that it be included in the ICA.
6. Audit the proposed ICA to ensure the applicable requirements have been included. Edit the ICA document to ensure it does not contain incorrect terminology or incorrect references and determine it does contain correct spelling, proper grammar, and accurate information.
7. When referring to another publication, ensure the information in the referenced publication meets the requirements of Appendix A, Part 29. It is the responsibility of the applicant to obtain authorization to use the information contained in the referenced publication. Submit a copy of each publication referenced in the applicant's ICA.
8. Submit two complete copies of the proposed ICA in binders, a copy of the completed Figure 1 document, and a copy of any referenced publication to the FAA/AUTHORITY in sufficient time to allow for evaluation prior to the date acceptance is needed. The average turnaround time is 20 to 30 days depending on the workload at that time.
9. When FAA/AUTHORITY receives the applicant's proposed ICA, the applicant and the appropriate FAA/AUTHORITY are notified. FAA/AUTHORITY reviews and evaluates the ICA in the order they are received.
10. If FAA/AUTHORITY finds the applicant's ICA does not meet the requirements, the review will be discontinued, and the applicant will be notified.
11. When the proposed ICA document, excluding the Airworthiness Limitations Section, is determined to be acceptable, the FAA/AUTHORITY will stamp, sign, and date the ICA. The applicant will be notified of the acceptance.
REVISION: (DATE) Page 2 Re visio n 4 Page Apdx A - 63
AC 29-2C, Chg 1 2/12/03 (MANUAL IDENTIFICATION) ATTACHMENT 4
TYPE DESIGN CHANGE
ICA RECOMMENDED PROCEDURES (Continued) Twidget Type Design Change Attachment 2
1. Use the list of appliances and modifications required for that Type Design Change (TDC) to determine which ATA chapters of the original rotorcraft manufacturer's maintenance manual the TDC will affect and which additional ATA chapters will be affected.
2. The following are component and systems that will be affected by the Twidget TDC:
a. Fuselage structure will be modified to mount twidget arm assembly.
b. Cabin door will be modified.
c. Electrical power will be required for electrical motor.
d. Hydraulic power source will be required for deploying and storing twidget arm.
e. Twidget control assembly will be installed in the cabin.
f. Control will be mounted in cockpit for emergency release of the twidget..
g. An Instrument will be installed in instrument panel indicating twidget's position.
h. Twidget recording equipment and monitor will be mounted in cabin.
i. Twidget antenna will be mounted on belly of fuselage.
j. Cables and wiring will be routed through rotorcraft.
k. Two-way communication will be required between the pilot and twidget operator.
I. Twidget gearbox requires servicing to full mark on site gage every 50 hours.
m. Twidget arm assemblies and clutch requires lubrication every 100 hours.
n. Twidget installation requires an inspection every 300 hours.
o. Twidget arm assembly requires an ultrasonic test every 600 hours.
p. Clutch has a wear tolerance of 1.56 mm.
q. Clutch is life-limited to be replaced every l,000 hours time in service.
r. Twidget gearbox is required to be overhauled every l,000 hours time in service.
s. Twidget gearbox attach bolt torque is 75-ft lb. and twidget arm assembly torque is 110 in lb.
t. Warning: Twidget should be retracted during takeoff, landing, and cruise above 85 knots.
u. Caution: Do not tow or taxi the rotorcraft with the twidget arm deployed.
v. Placards are required on the twidget unit and in the cockpit.
3. This example TDC will affect ATA-100 chapters: 4 Airworthiness Limitations, 5 Inspection, 6 Dimensions, 9 Towing and Taxiing, 10 Parking and Mooring, 11 Placards, 12 Servicing, 23 Communication, 24 Electrical, 25 Furnishings, 29 Hydraulic, 31 Indication and Recording, 52 Doors, and 53 Fuselage. A Chapter1 Introduction is also needed.
REVISION: (DATE) Revision 4 Page 3 Page Apdx A - 64
(MANUAL IDENTIFICATION) ATTACHMENT 4
TYPE DESIGN CHANGE
ICA RECOMMENDED PROCEDURES (Continued) INFORMATION:
Attachment 4 includes a Figure 2 for Thomas Copter Mods TDC to affix a Twidget installation on Thomas Copter model T-97J helicopter.
Figure 2 is intended to assist in determining which requirements are applicable to this certification project. The document contains each requirement with a set of parentheses, the appropriate regulation, and the location of information in the applicant’s ICA.
Information obtained from Attachment 4 can be used to determine which requirements are applicable. For requirements that are not applicable, place an N/A in the parentheses. All other requirements would be applicable to the certification project. Place a Y if the required information is included in ICA. Figure 2 has been completed for the sample Twidget TDC.
Applicant that uses and completes Figure 1 and indicates the location of that information in the applicant’s proposed ICA will reduce the time required to evaluate the ICA.
It is important that the applicant include the project number or numbers associated with the ICA, the name of the appropriate FAA/AUTHORITY office, the name of the project engineer, the applicant's company name, the make and model of rotorcraft being modified, and the date.
The completed Figure 1 should be submitted to FAA/AUTHORITY with the applicant's ICA.
REVISION:
Revision 4 (DATE) Page 4 Page Apdx A - 65
AC 29-2C, Chg 1 2/12/03 (MANUAL IDENTIFICATION) ATTACHMENT 4
TYPE DESIGN CHANGE
ICA RECOMMENDED PROCEDURES (Continued) APPENDIX A PART 29 REQUIREMENTS The following is a breakdown of Appendix A to FAR/JAR Part 29 and is intended to provide guidance to assist an applicant for a Type Design Change under a Type Certificate (TC), Supplemental Type Certificate (STC), or Field Approval (FA) requiring Instructions for Continued Airworthiness (ICA). The breakdown is intended to provide guidance to assist an applicant in understanding the ICA requirements of FAR/JAR § 29.1529. An applicant may use the guidance to prepare the ICA. Completion of this appendix will provide information needed for the evaluation and will reduce the time required for evaluation of the proposed ICA.
( ) Status of ICA: Y = Yes included; N/A = non- applicable. The Location Column lists the page number in the Applicant’s ICA that contains the information.
Project Number(s) ST01998RC-R ACO/FSDO: Rotorcraft ACO Project Engineer: Data Mastermine Applicant: Thomas Copter Mods Make: Thomas Copter Model: T97- J Date June 18, 1998 Requirement Regulation Location (N/A) ICA for each engine A29.1(b) N/A (N/A) ICA for each rotor A29.1(b) N/A ( Y ) ICA for each appliance required by this chapter A29.1(b) * All ( Y ) Any required information relating to the interface of the ( Y ) appliances, (N/A) engines and (N/A) rotors with the rotorcraft.
A29.1(b) See NOTE 1 ( Y ) If ICA are not supplied by the manufacturer of an (N/A) appliance, (N/A) engine or (N/A) rotor installed in the rotorcraft, the ICA for the rotorcraft must include ( Y ) the information essential to the continued airworthiness of the rotorcraft.
A29.1 * All ( Y ) A program showing how changes to the applicant’s ICA will be distributed.
A29.1(c) ATA 0 (N/A) A program showing how changes to the ICA of the manufacture of the engine(s), rotor(s) and appliances installed in the rotorcraft will be distributed, if referenced in applicant’s ICA A29.1(c) N/A ( Y ) ICA that must be in a form of a manual or manuals as appropriate for the quantity of data.
A29.2(a) * All ( Y ) A format of the manual or manuals which must provide for a practical arrangement.
A29.2(b) * All ( Y ) Content prepared in the English language. A29.3 * All Figure 2 REVISION: (DATE) Revision 4 Page 5 Page Apdx A - 66
(MANUAL IDENTIFICATION) ATTACHMENT 4
TYPE DESIGN CHANGE
ICA RECOMMENDED PROCEDURES (Continued) Requirement Regulation Location ( Y ) Introduction information that includes ( Y ) an explanation of the rotorcraft’s features and ( Y ) data to the extent necessary for maintenance and preventive maintenance.
A29.3(a)(1) ATA 0 ( Y ) A description of the (N/A) rotorcraft and its systems and installations, (N/A) engines and its systems and installations, (N/A) rotors and its systems and installations, ( Y ) appliances and its systems and installations.
A29.3(a)(2) ATA 25 ( Y ) Basic control and operating information describing ( Y ) how the rotorcraft components and systems are controlled and ( Y ) how the rotorcraft components and systems are operated including ( Y ) any special procedure and limitations.
A29.3(a)(3) ATA 25 ( Y ) Servicing information that covers details regarding ( Y ) servicing points, (N/A) capacities of tanks, ( Y ) capacities of reservoirs, ( Y ) types of fluids to be used, ( Y ) pressures applicable to the various systems.
A29.3(a)(4) ATA 12 ( Y ) Location of access panels for ( Y ) inspection and ( Y ) servicing.
A29.3 (a)(4) See NOTE 2 ( Y ) Servicing information that covers details regarding ( Y ) locations of lubrication points, ( Y ) the lubricant to be used.
A29.3(a)(4) ATA 12 ( Y ) Equipment required for servicing. A29.3(a)(4) ATA 12 ( Y ) Tow instructions and limitations. A29.3(a)(4) ATA 9 ( Y ) Mooring information A29.3(a)(4) ATA 10 (N/A) Jacking information A29.3(a)(4) N/A (N/A) Leveling information A29.3(a)(4) N/A ( Y ) Scheduling information for each part of the ( Y ) rotorcraft that, provides the recommended periods at which they should ( Y ) cleaned, ( Y ) inspected, ( Y ) adjusted, ( Y ) tested, ( Y ) lubricated and ( Y ) the work recommended at these periods.
A29.3(b)(1) See NOTE 3 (N/A) Scheduling information for the (N/A) rotorcraft’s engine(s) that provides the recommended periods at which they should be (N/A) cleaned, (N/A) inspected, (N/A) adjusted, (N/A) tested, (N/A) lubricated and (N/A) the work recommended at these periods. NOTE: This information may be in the FAA/AUTHORITY accepted engine ICA.
A29.3(b)(1) N/A Figure 2 (continued) REVISION: (DATE) Revision 4 Page 6 Page Apdx A - 67
AC 29-2C, Chg 1 2/12/03 (MANUAL IDENTIFICATION) ATTACHMENT 4
TYPE DESIGN CHANGE
ICA RECOMMENDED PROCEDURES (Continued) Requirement Regulation Location (N/A) Scheduling information for the (N/A) rotorcraft’s auxiliary power unit(s)(APU) that provides the recommended periods at which they should be (N/A) cleaned, (N/A) inspected, (N/A) adjusted, ( N/A) tested, (N/A) lubricated and (N/A) the work recommended at these periods.
A29.3(b)(1) N/A (N/A) Scheduling information for the (N/A) rotorcraft’s rotor(s) that provides the recommended periods at which they should be (N/A) cleaned, (N/A) inspected, (N/A) adjusted, (N/A) tested, (N/A) lubricated and (N/A) the work recommended at these periods.
A29.3(b)(1) N/A ( Y ) Scheduling information for the ( Y ) rotorcraft’s accessories that provides the recommended periods at which they should be ( Y ) cleaned, ( Y ) inspected, ( Y ) adjusted, ( Y ) tested, ( Y ) lubricated and ( Y ) the work recommended at these periods.
A29.3(b)(1) See NOTE 3 ( Y ) Scheduling information for the ( Y ) rotorcraft’s instruments that provides the recommended periods at which they should be ( Y ) cleaned, ( Y ) inspected, ( Y ) adjusted, ( Y ) tested, ( Y ) lubricated and ( Y ) the work recommended at these periods.
A29.3(b)(1) See NOTE 3 ( Y ) Scheduling information for the ( Y ) rotorcraft’s equipment that provides the recommended periods at which they should be ( Y ) cleaned, ( Y ) inspected, ( Y ) adjusted, ( Y ) tested, ( Y ) lubricated and ( Y ) the work recommended at these periods.
A29.3(b)(1) See NOTE 3 ( Y ) The degree of inspection for each part of the (N/A) rotorcraft and its (N/A) engine(s), (N/A) auxiliary power unit, ( N/A) rotor(s), ( Y ) accessories, ( Y ) Instruments and ( Y ) equipment.
A29.3(b)(1) ATA 5 ( Y ) The applicable wear tolerances A29.3(b)(1) ATA 25 The applicant may refer to an (N/A)accessory, (N/A) instrument, or (N/A) equipment manufacturer as the source of this information if the applicant shows (N/A) that the item has an exceptionally high degree of complexity requiring specialized maintenance techniques, test equipment, or expertise.
A29.3(b)(1) N/A ( Y ) The recommended overhaul periods and necessary cross references to the Airworthiness Limitation Section.
A29.3(b)(1) ATA 5 Figure 2 (continued) REVISION: (DATE) Revision 4 Page 7 Page Apdx A - 68
(MANUAL IDENTIFICATION) ATTACHMENT 4
TYPE DESIGN CHANGE
ICA RECOMMENDED PROCEDURES (Continued) Requirement Regulation Location ( Y ) An inspection program that includes ( Y ) the frequency and ( Y ) extent of the inspection necessary to provide for the continued airworthiness of the rotorcraft.
A29.3(b)(1) ATA 5 ( Y ) Troubleshooting information describing ( Y ) problem malfunctions, ( Y ) how to recognize those malfunctions and ( Y ) the remedial action for those malfunctions.
A29.3(b)(2) See NOTE 4 (N/A) Information describing the order and method of (N/A) removing and (N/A) replacing engine(s) with any necessary precautions to be taken.
A29.3(b)(3) N/A (N/A) Information describing the order and method of (N/A) removing and (N/A) replacing rotor(s) with any necessary precautions to be taken.
A29.3(b)(3) N/A ( Y ) Information describing the order and method of ( Y ) removing and ( Y ) replacing parts with any necessary precautions to be taken.
A29.3(b)(3) ATA 25 ( Y ) Other general procedural instructions including (N/A) storage limitations and procedures for (N/A) testing system during ground running, (N/A) making symmetry checks, ( Y ) weighing and determining the center of gravity, (N/A) lifting, (N/A) shoring.
A29.3(b)(4) ATA 8 (N/A) Diagrams of structural access plates and information needed to gain access for inspections when access plates are not provided.
A29.3(c) N/A (N/A) Details for the application of special inspection techniques including radiographic and ultrasonic testing where such process are specified.
A29.3(d) N/A (N/A) Information needed to apply protective treatment to structure after inspection.
A29.3(e) N/A ( Y ) All data relative to structural fasteners such as ( Y ) identification, ( Y ) discarded recommendations, and ( Y ) torque values.
A29.3(f) ATA25 ( Y ) A list of special tools needed A29.3(g) NOTE 5 ( Y ) The Instructions for Continued Airworthiness must contain a section, titled Airworthiness Limitations that is ( Y ) segregated and ( Y ) clearly distinguishable from the rest of the document. NOTE: The Airworthiness Limitations Section in the applicant’s ICA will be evaluated by the appropriate FAA/AUTHORITY.
A29.4 ATA 4 Figure 2 (continued) REVISION: (DATE) Revision 4 Page 8 Page Apdx A - 69
AC 29-2C, Chg 1 2/12/03 (MANUAL IDENTIFICATION) ATTACHMENT 4
TYPE DESIGN CHANGE
ICA RECOMMENDED PROCEDURES (Continued) Requirement Regulation Location (N/A) The Airworthiness Limitations Section must set forth each mandatory replacement time, structural inspection procedure approved under § 29.571.
A29.4 N/A ( Y ) If the Instructions for Continued Airworthiness consist of multiple documents, the Airworthiness Limitations Section required by this paragraph must include in the principal manual.
A29.4 ATA 4 ( Y ) The Airworthiness Limitations Section must contain a legible statement in a prominent location indicating that the Airworthiness Limitations Section is FAA/AUTHORITY-approved and specifies required maintenance and/or inspections. The exact, required wording of this statement is found in the FAR/JAR.
A29.4 ATA 4 Figure 2 (continued) NOTE: The Airworthiness Limitations Section (ALS) is evaluated and approved by FAA/AUTHORITY.
REVISION: (DATE) Revision 4 Page 9 Page Apdx A - 70
(MANUAL IDENTIFICATION)
THIS PAGE INTENTIONALLY LEFT BLANK REVISION: (DATE) Revision 4 Page 10 Page Apdx A - 71
AC 29 APPENDIX B. AIRWORTHINESS GUIDANCE FOR ROTORCRAFT INSTRUMENT FLIGHT.
a. Explanation.
(1) Requirements for instrument flight rules (IFR) have been incorporated into Appendix B to part 29, utilizing a regulatory format. Various information from previous interim standards, procedures, test techniques, and acceptable means of compliance for rotorcraft IFR flight is included in the following sections.
(2) Amendment 29-51 made a change to paragraph V. Static Lateral Directional Stability, concurrent with the change to § 29.177, to allow for a small range of sideslip angles (2-3 degrees) for which sideslip angles need not increase steadily with control deflection. The previous rule language stating that directional control position must increase in approximate constant proportion with sideslip angle has been replaced. The intent of this change is that an increase in directional control position must produce an increase in sideslip angle linearly. At greater sideslip angles appropriate to the type rotorcraft, increase in directional control position need not produce a linear increase in sideslip angle but should not become neutral or negative. The change in paragraph VII revised the current requirement to clearly state the requirements to be met in the event of a stability augmentation system (SAS) failure.1
b. Procedures.
(1) General.
(i) The certificated instrument flight envelope may be more restrictive than the visual flight rules (VFR) envelope in terms of weight, CG, speed, altitude, or rate of climb and descent. The approved envelope should be operationally practical such that it does not impose constraints with which the crew has difficulty complying.
(ii) Controllability requirements are to be met from 0.9 VMINI to 1.1 VNE.
Stability requirements must be met where specified. Stability devices are to be designed to allow safe flight following a failure. The evaluating pilot should assure that all equipment and devices installed for IFR, including reasonable failures of that equipment, do not compromise the VFR approval for that rotorcraft. For example, stability system failures can cause loss of swashplate or tail rotor control travel when failed in a hardover condition. If the device remains in the hardover position after the stability system is turned off, control capability may be compromised. Cyclic controllability tests at high speed and at the limiting rearward flight condition, or tail rotor tests in sideward flight at high altitude, may reveal a lower control capability and a more restrictive envelope. In addition, controllability testing should be accomplished with the control rigging set at the most adverse production tolerance for the test condition (e.g., minimum forward swashplate for high speed testing).
1 This paragraph was effective 9/17/2009 as part of the new and changed guidance material for the Performance and Handling Qualities final rule (Amdt. 29-51, 73 FR 11002, Feb. 29, 2008).
Page Apdx B - 1