Service bulletin · Airbus Helicopters

On this page

Copies · 6

Copies of this document that the FAA filed in AD dockets on regulations.gov, newest revision first. A newer revision may exist.

Revision 7Airbus Helicopters EASB No_ 05A017 Rev 7 · 16 pages · 1.5 MB

© Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2020-1182; AD 2021-09-05 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Docket FAA-2020-1182 (document 0005) · AD 2021-09-05

Revision 2Airbus EASB 05A017 Rev 2 · 12 pages · 1.5 MB

© Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2015-3970; AD 2016-08-20 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Docket FAA-2015-3970 (document 0005) · AD 2016-08-20

Revision 2U.S. DOT/FAA - Eurocopter EASB No 05A017 rev2 · 12 pages · 1.2 MB

© Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2013-0501; AD 2014-02-04 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Docket FAA-2013-0501 (document 0004) · AD 2014-02-04

Revision 2U.S. DOT/FAA - Eurocopter Emergency Alert Service Bulletin No. 05A017 · 20 pages · 323 KB

© Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2012-0005; AD 2012-01-03 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Docket FAA-2012-0005 (document 0002) · AD 2012-01-03

Revision 3U.S. DOT/FAA - Eurocopter ASB 05A017 · 19 pages · 473 KB

© Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2013-0307; AD 2013-07-06 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Docket FAA-2013-0307 (document 0002) · AD 2013-07-06

U.S. DOT/FAA - Airbus EASB No 05A017 Rev 0U.S. DOT/FAA - Airbus EASB No 05A017 Rev 0 · 10 pages · 418 KB

© Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2014-0515; AD 2014-12-51 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Docket FAA-2014-0515 (document 0002) · AD 2014-12-51

Manufacturer
Airbus Helicopters
Type
Emergency Alert Service Bulletin
Number
05A017
Latest revision known
05A017, Revision 7, dated March 21, 2018

A newer revision may exist than any OpenAirDocs knows of: check with the manufacturer.

ADs that cite it · 7

Newest first, with the revision each names, as OpenAirDocs read it from the AD’s text: check it against the AD.

All 7 ADs

Also cited in 3 proposed ADs.

Text · 16OCR

Revision 7, the newest copy. This text is OCR from a scan. OCR can misread letters and numbers. © Airbus Helicopters. Filed by the FAA in regulations.gov docket FAA-2020-1182; AD 2021-09-05 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = '3dd7828f981a6255326f4c2d0f426b4997dd2eb9484ab2f6f115281806112fe0'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Page 1OCROpen in PDF

AIRBUS

HELICOPTERS EASB

EMERGENCY

ALERT SERVICE BULLETIN

PROTECTIVE MEASURE

FUSELAGE Check of the tail boom / Fenestron junction frame ATA: 53 For the attention of AIRCRAFT Version (S) NUMBER CONCERNED Civil Military EC130 05A017 B4, T2 Revision No. Date of issue Revision O 2014-06-06 Revision 1 2014-06-13 Revision 2 2015-02-20 Revision 3 2016-03-07 Revision 4 2016-11-30 Revision 5 2017-04-21 Revision 6 2017-05-03 Revision 7 2018-03-21 Summary:

Visual check for cracks on the tail boom / Fenestron junction frame.

Reason for last Revision:

The purpose of Revision 7 is to cancel the instructions of this ALERT SERVICE BULLETIN for helicopters on which modification 074775 was embodied.

Compliance:

Compliance with this ALERT SERVICE BULLETIN is mandatory.

Revision 0 2014-06-06 Page 1/16 Revision 7 2018-03-21 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 2OCROpen in PDF

AIRBUS

HELICOPTERS EASB

1. PLANNING INFORMATION

1.A. EFFECTIVITY

1.A.1. Helicopters/installed equipment EC130 B4 and T2 helicopters on which modification 074775 (Reinforcement of the EC130 Fenestron frame by installing 4 carbon patches) was not embodied.

NOTE 1 Refer to the aircraft Individual Inspection Log Book (RIC AMS) to identify the actual modification status of the helicopter.

NOTE 2 Modification 074775 is proposed as a retrofit through Service Bulletin No. 53-036.

1.A.2. Non-installed equipment Not applicable.

1.B. ASSOCIATED REQUIREMENTS Not applicable.

1.C. REASON Revision 0:

On the EC130 B4 tail boom / Fenestron junction frame, two cases of cracks were found in a new area of the tail boom / Fenestron junction frame during non-scheduled inspections.

Examination revealed that the crack initiated in the radius between the web and the flange on the tail cone side, in the lower RH part of the tail boom / Fenestron junction frame (Detail A, Figure 1).

It spread rapidly, following the radius along the web of the tail boom / Fenestron junction frame.

The cracks are of considerable length and no deterioration is visible from outside the helicopter.

The inspection of this area which can reveal these cracks is scheduled at the "600 hours // 2 years" inspection.

Information Notice (IN) No. 2167-1-53 was issued on June 15, 2010 to specify the applicable maintenance.

Considering the cases encountered in service, this periodicity is unsuitable.

In these conditions and under high tail rotor thrust load, the resistance margins of this junction may be insufficient.

Consequently, Airbus Helicopters makes compliance with this ALERT SERVICE BULLETIN mandatory. Its purpose is to enable a detailed visual check from inside the tail boom.

Revision 0 2014-06-06 Page 2/16 Revision 7 2018-03-21 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 3OCROpen in PDF

AIRBUS

HELICOPTERS EASB Revision 1:

The purpose of Revision 1 is to refer to the flying hours logged by the tail boom / Fenestron junction frame instead of the flying hours logged by the helicopter, in paragraph 1.E.2.

Revision 2:

Compliance with the previous revisions of this ALERT SERVICE BULLETIN required an inspection from inside the tail boom, with or without removal of the stabilizer.

As this inspection from inside can be complex, the purpose of Revision 2 of this ALERT SERVICE BULLETIN is to propose an alternative inspection from outside the tail boom, which is possible following compliance with Service Bulletin No. 53-029, and to define who is allowed to perform the different checks.

Furthermore, a follow-up in sling cycles has been added for helicopters which carry out external load carrying operations.

Revision 3:

Following investigation, Airbus Helicopters hereby informs you that the time limit for inspecting the tail boom / Fenestron junction frame increases from 700 to 1200 flying hours.

As a result, tail booms which have logged between 700 and 1200 flying hours from receipt of revision 3 of this ALERT SERVICE BULLETIN are no longer concerned by the directives of this ALERT SERVICE BULLETIN until the frame has logged 1200 flying hours.

Consequently, Airbus Helicopters renders compliance with this ALERT SERVICE BULLETIN mandatory, its purpose being to facilitate a visual detailed check of the tail boom / Fenestron junction frame from 1200 flying hours logged by the tail boom / Fenestron junction frame.

Revision 4:

Following a new case of crack in the tail boom / Fenestron junction frame, Airbus Helicopters suspects that the belated detection of the crack is due to incorrect cleaning of the area.

Therefore, the purpose of Revision 4 of this ALERT SERVICE BULLETIN is to make the periodic cleaning of the area to be inspected on the tail boom / Fenestron junction frame, from inside the tail boom, mandatory.

Revision 5:

Following a new case of crack in the tail boom / Fenestron junction frame, which was detected during compliance with this ALERT SERVICE BULLETIN at 1200 flying hours, Airbus Helicopters has decided to reduce the inspection interval, pending analysis and examination of this new case.

Therefore, the purpose of Revision 5 of this ALERT SERVICE BULLETIN is to reduce the time limit for first compliance with this inspection to 350 flying hours.

Revision 6:

The purpose of Revision 6 is to make it mandatory to inspect the tail boom / Fenestron junction frame from inside the tail boom every 660 flying hours on helicopters on which Service Bulletin No. 53-029 was complied with.

Revision 7:

The purpose of Revision 7 of this ALERT SERVICE BULLETIN is:

- to inform operators that the embodiment of modification 074775 cancels the instructions of this ALERT

SERVICE BULLETIN,

- to modify compliance with paragraph 1.E.2. by requesting the embodiment of modification 074775 through Service Bulletin No. 53-036 before 31/12/2022.

Revision 0 2014-06-06 Page 3/16 Revision 7 2018-03-21 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 4OCROpen in PDF

AIRBUS

HELICOPTERS EASB

1.D. DESCRIPTION Compliance with this ALERT SERVICE BULLETIN consists in checking that there are no cracks on the tail boom / Fenestron junction frame.

1.E. COMPLIANCE

1.E.1. Compliance at the works Not applicable.

1.E.2. Compliance in service Helicopters/installed equipment:

a) For helicopters which do not yet comply with this ALERT SERVICE BULLETIN and are equipped with a tail boom/Fenestron junction frame which has logged less than 325 flying hours:

1) Which do not comply with Service Bulletin No. 53-029 (See NOTE 3) Comply with paragraph 3.B.5. then 3.B.1. at the latest upon reaching 350 flying hours, Then, Comply with paragraph 3.B.1. or 3.B.2. at intervals not exceeding 25 flying hours or 390 cycles - See NOTE 4 (first time limit reached).

And, Comply with paragraph 3.B.5. then 3.B.1. at intervals not exceeding 150 flying hours.

Or,

2) Which comply with Service Bulletin No. 53-029 (See NOTE 3) Comply with paragraph 3.B.3. at the latest upon reaching 350 flying hours, Then, Comply with paragraph 3.B.3. at intervals not exceeding 10 flying hours or 250 cycles - See NOTE 4 (first time limit reached).

And, Comply with paragraphs 3.B.5. then 3.B.1. at intervals not exceeding 660 flying hours.

b) For helicopters which do not yet comply with this ALERT SERVICE BULLETIN and are equipped with a tail boom/Fenestron junction frame which has logged between 325 and 675 flying hours:

1) Which do not comply with Service Bulletin No. 53-029 (See NOTE 3) Comply with paragraph 3.B.5. then 3.B.1. within 25 flying hours following receipt of Revision 5, issued on the date indicated at the bottom of the page, Then, Comply with paragraph 3.B.1. or 3.B.2. at intervals not exceeding 25 flying hours or 390 cycles since the latest inspection - See NOTE 4 (first time limit reached).

And, Comply with paragraphs 3.B.5. and 3.B.1. at intervals not exceeding 150 flying hours.

Or, Revision 0 2014-06-06 Page 4/16 Revision 7 2018-03-21 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 5OCROpen in PDF

AIRBUS

HELICOPTERS EASB

2) Which comply with Service Bulletin No. 53-029 (See NOTE 3) Comply with paragraph 3.B.3. within 10 flying hours, then at intervals not exceeding 10 flying hours or 250 cycles since the latest inspection - See NOTE 4 (first time limit reached).

And, Comply with paragraphs 3.B.5. then 3.B.1. at intervals not exceeding 660 flying hours.

c) For helicopters which do not yet comply with this ALERT SERVICE BULLETIN and are equipped with a tail boom/Fenestron junction frame which has logged between 675 and 690 flying hours:

1) Which do not comply with Service Bulletin No. 53-029 (See NOTE 3) Comply with paragraph 3.B.5. then 3.B.1. at the latest upon reaching 700 flying hours, Then, Comply with paragraph 3.B.1. or 3.B.2. at intervals not exceeding 25 flying hours or 390 cycles since the latest inspection - See NOTE 4 (first time limit reached).

And, Comply with paragraphs 3.B.5. and 3.B.1. at intervals not exceeding 150 flying hours.

Or,

2) Which comply with Service Bulletin No. 53-029 (See NOTE 3) Comply with paragraph 3.B.3. within 10 flying hours, then at intervals not exceeding 10 flying hours or 250 cycles since the latest inspection - See NOTE 4 (first time limit reached).

And, Comply with paragraphs 3.B.5. then 3.B.1. at intervals not exceeding 660 flying hours.

For helicopters which do not comply with this ALERT SERVICE BULLETIN or are equipped with a tail boom/Fenestron junction frame which has logged more than 690 flying hours:

1) Which do not comply with Service Bulletin No. 53-029 (See NOTE 3) Comply with paragraph 3.B.5. then 3.B.1. within 10 flying hours following receipt of Revision 5, issued on the date indicated at the bottom of the page, Then, Comply with paragraph 3.B.1. or 3.B.2. at intervals not exceeding 25 flying hours or 390 cycles since the latest inspection - See NOTE 4 (first time limit reached).

And, Comply with paragraphs 3.B.5. and 3.B.1. at intervals not exceeding 150 flying hours.

Or,

2) Which comply with Service Bulletin No. 53-029 (See NOTE 3) Comply with paragraph 3.B.3. within 10 flying hours, then at intervals not exceeding 10 flying hours or 250 cycles since the latest inspection - See NOTE 4 (first time limit reached).

And, Comply with paragraphs 3.B.5. then 3.B.1. at intervals not exceeding 660 flying hours.

Revision 0 2014-06-06 Page 5/16 Revision 7 2018-03-21 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 6OCROpen in PDF

AIRBUS

HELICOPTERS EASB

e) For helicopters which already comply with this ALERT SERVICE BULLETIN:

1) Which do not comply with Service Bulletin No. 53-029 (See NOTE 3) Comply with paragraph 3.B.1. or 3.B.2. at intervals not exceeding 25 flying hours or 390 cycles since latest inspection - See NOTE 4 (first time limit reached).

And, Comply with paragraphs 3.B.5. and 3.B.1. at intervals not exceeding 150 flying hours.

Or,

2) Which comply with Service Bulletin No. 53-029 (See NOTE 3) Comply with paragraph 3.B.3. at intervals not exceeding 10 flying hours or 250 cycles since latest inspection - See NOTE 4 (first time limit reached).

And, Comply with paragraphs 3.B.5. then 3.B.1. at intervals not exceeding 660 flying hours.

NOTE 3 The purpose of SB No. 53-029 is to cut out the splice and skin at the tail boom/Fenestron junction frame, in order to facilitate the periodic inspection in this ALERT SERVICE BULLETIN.

NOTE 4 Counting cycles:

1 landing with or without stopping the rotor = 1 cycle 1 external load transportation operation = 1 cycle

f) For all helicopters:

1) On which modification 074609 (Reinforcement of the Fenestron/tail boom link) was not embodied Comply with Service Bulletin No. 53-036 (Modification 074775) before 31/12/2022.

2) On which modification 074609 (Reinforcement of the Fenestron/tail boom link) was embodied Contact your usual Customer Logistics Manager (CLM) to define the conditions for embodiment of modification 074775 before 31/12/2022.

Non-installed equipment: Not applicable.

1.F. APPROVAL Approval of modifications:

Not applicable.

Revision 0 2014-06-06 Page 6/16 Revision 7 2018-03-21 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 7OCROpen in PDF

AIRBUS

HELICOPTERS EASB Approval of this document:

The technical information contained in this ALERT SERVICE BULLETIN Revision 0 was approved on June 06, 2014 under the authority of EASA Design Organization Approval No. 21J.056 for helicopters of civil versions subject to an Airworthiness Certificate.

The technical information contained in this ALERT SERVICE BULLETIN Revision 1 was approved on June 13, 2014 under the authority of EASA Design Organization Approval No. 21J.056 for helicopters of civil versions subject to an Airworthiness Certificate.

The technical information contained in this ALERT SERVICE BULLETIN Revision 2 was approved on February 20, 2015 under the authority of EASA Design Organization Approval No. 21J.056 for helicopters of civil versions subject to an Airworthiness Certificate.

The technical information contained in this ALERT SERVICE BULLETIN Revision 3 was approved on March 02, 2016 under the authority of EASA Design Organization Approval No. 21J.056 for helicopters of civil versions subject to an Airworthiness Certificate.

The technical information contained in this ALERT SERVICE BULLETIN Revision 4 was approved on November 30, 2016 under the authority of EASA Design Organization Approval No. 21J.700 for civil version helicopters subject to an Airworthiness Certificate.

The technical information contained in this ALERT SERVICE BULLETIN Revision 5 was approved on April 21, 2017 under the authority of EASA Design Organization Approval No. 21J.700 for civil version helicopters subject to an Airworthiness Certificate.

The technical information contained in this ALERT SERVICE BULLETIN Revision 6 was approved on May 02, 2017 under the authority of EASA Design Organization Approval No. 21J.700 for civil version helicopters subject to an Airworthiness Certificate.

The technical information contained in this ALERT SERVICE BULLETIN Revision 7 was approved on March 20, 2018 under the authority of EASA Design Organization Approval No. 21J.700 for civil version helicopters subject to an Airworthiness Certificate.

1.G. MANPOWER For compliance with this ALERT SERVICE BULLETIN, Airbus Helicopters recommends the following personnel qualifications:

Qualification:

- 1 Technician to comply with paragraphs 3.B.1., 3.B.2., 3.B.3. (a) and (b) and 3.B.5.

Or,

- 1 Pilot to comply with paragraph 3.B.3.(a).

Or,

- 1 Person appropriately trained and certified, in accordance with the local regulations in force, to comply with paragraphs 3.B.2., 3.B.3.(a) and (b).

The time for the operations is given for information purposes, for a standard configuration.

Time for the operations: approximately 1 hour to comply with paragraph 3.B.1. (with removal of the stabilizer) approximately 30 minutes to comply with paragraph 3.B.2. (without removal of the stabilizer) approximately 10 minutes to comply with paragraph 3.B.3.

approximately 1 hour to clean the frame (paragraph 3.B.5.) with removal of the stabilizer Revision 0 2014-06-06 Page 7/16 Revision 7 2018-03-21 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 8OCROpen in PDF

AIRBUS

HELICOPTERS EASB

1.H. WEIGHT AND BALANCE Not applicable.

1.I. EFFECT ON ELECTRICAL LOADS Not applicable.

1.J. SOFTWARE MODIFICATION EMBODIMENT RECORD Not applicable.

1.K. REFERENCES Aircraft Maintenance Manual (AMM):

AMM: 55-11-00,4-1: Removal/Installation - Horizontal stabilizer Standard Practices Manual (MTC):

- MTC: 20.04.01.102: Use of cleaning products on individual parts and on aircraft

- MTC: 20.02.09.101: Crack detection through dye-penetrant inspection: General

- MTC: 20.02.09.601: Checking structural parts/components using the dye-penetrant procedure

1.L. DOCUMENTS AFFECTED Not applicable.

1.M. INTERCHANGEABILITY OR MIXABILITY OF PARTS Not applicable.

Revision 0 2014-06-06 Page 8/16 Revision 7 2018-03-21 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 9OCROpen in PDF

AIRBUS

HELICOPTERS EASB

2. MATERIAL INFORMATION

2.A. MATERIAL: PRICE - AVAILABILITY - PROCUREMENT Not applicable.

2.B. INFORMATION CONCERNING INDUSTRIAL SUPPORT Not applicable.

2.C. MATERIAL REQUIRED FOR EACH HELICOPTER/COMPONENT Products to be ordered separately:

As per the Work Cards specified in this ALERT SERVICE BULLETIN and the list below:

Designation Qty Product P/N CM Item MEK cleaning agent ALD METHYL ETHYL KETONE CM217 The products can be ordered separately from the KLX AEROSPACE SOLUTIONS company.

Website: https://www.klxaerospace.com/klxaero/ Telephone: +1.305.925.2600 AOG: +1.305.471.8888

2.D. MATERIAL TO BE RETURNED Not applicable.

Revision 0 2014-06-06 Page 9/16 Revision 7 2018-03-21 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 10OCROpen in PDF

AIRBUS

HELICOPTERS EASB

3. ACCOMPLISHMENT INSTRUCTIONS

3.А. GENERAL NOTE 1 Contact details of the Airbus Helicopters Customer Service Technical Support Department:

Fax: +33 (0)4.42.85.99.66.

E-mail: support.technical-airframe.ah@airbus.com Keycopter: Technical Request Management

3.B. OPERATIONAL PROCEDURE

3.B.1. Inspection of the tail boom / Fenestron junction frame from inside the tail boom with removal of the stabilizer As per Figures 1 and 3:

- Remove the horizontal stabilizer as per AMM Task 55-11-00,4-1.

- If necessary, clean the area to be checked defined in Figure 1 of the junction frame (a) (see detail A and cross-section B-B) as per MTC Work Card 20.04.01.102.

NOTE 2 For this inspection, the surface of the frame must be clean.

- Check that there are no cracks on the web of the frame (a) and in the radius between the web and the flange on the tail cone side. Pay particular attention to the area around the 4 spars (b). (See Detail C) . If in doubt, perform a local non-destructive inspection of the inspection area (e.g. dye-penetrant inspection as per MTC Work Cards 20.02.09.101 and 20.02.09.601).

Then interpret the results as per paragraph 3.B.4.

3.B.2. Inspection of the tail boom / Fenestron junction frame from inside the tail boom without removal of the stabilizer As per Figures 2 and 3:

NOTE 3 For this inspection, the surface of the frame must be clean.

- Using a borescope through the stabilizer opening, check that there are no cracks on the web of the frame (a) and in the radius between the web and the flange on the tail cone side. Pay particular attention to the area around the 4 spars (b). (See Detail C):

. If in doubt, perform a local non-destructive inspection of the inspection area (e.g. dye-penetrant inspection as per MTC Work Cards 20.02.09.101 and 20.02.09.601).

Then interpret the results as per paragraph 3.B.4.

Revision 0 2014-06-06 Page 10/16 Revision 7 2018-03-21 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 11OCROpen in PDF

AIRBUS

HELICOPTERS EASB

3.B.3. Inspection of the tail boom / Fenestron junction frame from outside the tail boom NOTE 4 This inspection can only be performed following compliance with Service Bulletin No. 53-029.

As per Figure 4:

a) Check that there are no cracks on frame (a) in the area of the skin cut-outs (upper and lower RH side, upper and lower LH side) (See Detail A - Figure 4).

Only the RH side is shown in Figure 4. The LH side is identical.

b) If in doubt, perform a local non-destructive inspection of the inspection area (e.g. dye-penetrant inspection as per MTC Work Cards 20.02.09.101 and 20.02.09.601).

CAUTION

THIS CHECK MUST BE PERFORMED IN AN UNPAINTED, CLEAN AREA.

Then interpret the results as per paragraph 3.B.4.

3.B.4. Interpretation of the results

a) If there are no cracks:

• Leave as is.

If previously removed, install the horizontal stabilizer as per AMM Task 55-11-00,4-1.

. Resume flights.

b) If any cracks are found:

Before resuming flights:

. Contact Airbus Helicopters to define the conditions for returning the helicopter to conformity (refer to NOTE 1).

3.B.5. Cleaning of the tail boom / Fenestron junction frame from inside the frame

- Remove the horizontal stabilizer as per AMM Task 55-11-00,4-1.

- Clean junction frame (a) (Figure 1) using a white clean and lint-free cloth soaked with liquid MEK (METHYL

ETHYL KETONE) Then, Comply with paragraph 3.B.1.

Revision 0 2014-06-06 Page 11/16 Revision 7 2018-03-21 This document is available on the internet: www.airbushelicopters.com/techpub/

Page 12OCROpen in PDF

AIRBUS

HELICOPTERS EASB

3.C. IDENTIFICATION Identification of this document:

Record first compliance with this ALERT SERVICE BULLETIN in the helicopter documents.

3.D. OPERATING AND MAINTENANCE INSTRUCTIONS Not applicable.

Revision 0 2014-06-06 Page 12/16 Revision 7 2018-03-21 This document is available on the internet: www.airbushelicopters.com/techpub/