Copy · U.S. DOT/FAA - Boeing Service Bulletin · 63 pages

© The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2012-0862; AD 2014-05-31 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

TextPartly OCR

Some pages are OCR from a scan. OCR can misread letters and numbers.

Query with SQL
duckdb -csv -c "SELECT p.page, p.text_source, p.text, f.rights_holder, f.license
  FROM 'https://openairdocs.org/data/latest/service_document_file_page.parquet' p JOIN 'https://openairdocs.org/data/latest/service_document_file.parquet' f USING (file_sha256)
  WHERE p.file_sha256 = 'd4e2841c96bb8fbabfcc20a490a23e9e6b7c57863acd6f01dc56592dcde1975d'
  ORDER BY p.page"

Prints the whole list as CSV. It reads the release’s Parquet files over HTTPS, so there’s nothing to download first. Install DuckDB to run it.

Show pages 13–24

3. ACCOMPLISHMENT INSTRUCTIONS A. GENERAL INFORMATION CAUTION: KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF METAL PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED MATERIAL,

METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE BUNDLES CAN CAUSE DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR OTHER ELECTRICAL DAMAGE.

NOTE: 1. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for definition of the acronyms.

2. Obey all of the warnings and cautions given in the specified manual sections.

3. Unless shown differently, these dimensions and tolerances are used:

– Linear dimensions are in inches – Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus or minus 0.03 inch – Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch – Angular tolerance is plus or minus 2 degrees – Hole dimensions for standard solid rivets are given in 747 SRM 51 – Torque limits to tighten nuts and bolts are given in 747 SRM 51

4. Use the approved fastener and process material substitutions in accordance with 747 SRM 51.

5. Refer to the SWPM 20-10-11 and SWPM 20-10-12 for the wire installation procedures, and SWPM 20-10-19 for the wire separation requirements, as accepted procedures.

6. If the length of any fastener specified in this service bulletin does not meet the installation standards in 747-400SF SRM 51, then a fastener of the same specification, or an approved substitute, with a length which meets the installation standards in 747-400SF SRM 51 may be used.

7. These work instructions refer to procedures included in other Boeing documents.

When the words "refer to" are used and the operator has an accepted alternative procedure, the accepted alternative procedure can be used. When the words "in accordance with" are included in the instruction, the procedure in the Boeing document must be used.

8. Loosen additional clamps and hardware as required to allow moment of wire bundles to new ring post locations. Tighten any clamps and hardware that were loosened to facilitate movement of wire bundles. Refer to the SWPM 20-10-11, SWPM 20-10-12 , and SWPM 20-10-19, as accepted procedures.

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 23, 2010 747-25A3581Revision 2: September 11, 2012 25 of 63 BOEING SERVICE BULLETIN 747-25A3581

ALERTALERT

B. WORK INSTRUCTIONS

1. Gain access to left forward Main Equipment Compartment (MEC). Refer to 747-400 AMM 53-21-02 as an accepted procedure.

2. Remove existing drip shield in accordance with Figure 1.

3. Loosen wire bundles routing in accordance with Figure 2.

4. Install provisions for wire bundle routing in accordance with Figure 3.

5. Relocate wire bundle routing in accordance with Figure 4.

6. Install new drip shield brackets and new drip shield in accordance with Figure 5.

7. Install drip shield deflectors in accordance with Figure 6.

8. Install new insulation blanket in accordance with Figure 7.

9. Put the airplane back to a serviceable condition.

Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 23, 2010 747-25A3581Revision 2: September 11, 2012 26 of 63 BOEING SERVICE BULLETIN 747-25A3581

ALERTALERT

Page 27OCROpen in PDF

BOEING SERVICE BULLETIN 747-25A3581

ALERT ALERT

STA TYPICAL 400 STA 400

BULKHEAD STA 340 STA 340 TYPICAL 1959064 FIGURE 1: ELECTRONICS EQUIPMENT CENTER - REMOVAL OF EXISTING DRIP SHIELD (SHEET 1 OF 6) Original Issue: September 23, 2010 Revision 2 September 11, 2012 PROPRIETARY - Copyright ® Unpublished Export Controlled ECCN: 9E991 - BOEING 747-25A3581 Work - See page 1 for details. 27 of 63

Page 28OCROpen in PDF

BOEING SERVICE BULLETIN 747-25A3581

ALERT ALERT _WL 186 STA 340

STA FWD 360 STA A-A 400 FIGURE 1: ELECTRONICS EQUIPMENT CENTER - REMOVAL OF EXISTING DRIP SHIELD (SHEET 2 OF 6) Original Issue: September 23, 2010 Revision 2 September 11, 2012 Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 28 of 63

Page 29OCROpen in PDF

BOEING SERVICE BULLETIN 747-25A3581

ALERT ALERT C — STRAP CLAMP WASHER SCREW

STANDOFF INBD STA 340 BULKHEAD LBL (VIEW LOOKING FORWARD) 20 B-B LBL

25.60 INBD C-C 1963098 FIGURE 1: ELECTRONICS EQUIPMENT CENTER - REMOVAL OF EXISTING DRIP SHIELD (SHEET 3 OF 6) Original Issue: September 23, 2010 Revision 2 September 11, 2012 PROPRIETARY - Copyright © Unpublished Export Controlled ECCN: 9E991 - BOEING 747-25A3581 Work - See page 1 for details. 29 of 63

Page 30OCROpen in PDF

BOEING SERVICE BULLETIN 747-25A3581

ALERT ALERT

8) BRACKET BRACKET 8 STA STA 340 380 FWD BULKHEAD STA 400 •

TYPICAL E-E BULKHEAD

D-D STA 400 STA 360 STA 340 BRACKET 9

5) 10 LOCATIONS F-F C 1963095 FIGURE 1: ELECTRONICS EQUIPMENT CENTER - REMOVAL OF EXISTING DRIP SHIELD (SHEET 4 OF 6) Original Issue: September 23, 2010 Revision 2 September 11, 2012 Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 30 of 63

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY numbers shown below are the number of parts necessary for this figure.

More DataQtyIdentificationNameTaskStep near STA 340 and STA 400 2BACS38K1STRAPRemove1 1-DRAINAGE TUBE CLAMP Remove2 STA 340, LBL 25.60, WL 180 2-FASTENERRemove From horizontal stiffener (STA 340, LBL

25.60, WL 180) 1-SUPPORTING

STANDOFF Remove

(a) Fill holes in horizontal stiffener (STA 340, LBL 25.60, WL

180) 2BACR15BA4AD6CRIVET, 100 DEGInstall (New)

(b) Typical:--DRAINAGE TUBE CLAMP Loosen3 1 STA 340 and 3 STA 400 near STA 340 and STA 400 2-DRAINAGE TUBEDisconnect4 6 (STA 340) and 4 (STA 400) 10-FASTENERRemove5 at STA 3603-SCREWRemove6 at STA 3803-SCREWRemove 284U1364-1, or -2, or -3.

1-DRIP SHIELDRemove7 3 (STA 340 bulkhead) and 1 (STA 400 bulkhead) 4284U1363-1BRACKET - DRIP

SHIELD MOUNTING Remove8 6 (STA 340 bulkhead) and 2 (STA 400 bulkhead) 8-FASTENERRemove

(a) Fill holes 6 (STA

340) and 2 (STA

400). Flush is not required.

8BACR15BA5AD4CRIVET, 100 DEGInstall (New) FIGURE 1: ELECTRONICS EQUIPMENT CENTER - REMOVAL OF EXISTING DRIP SHIELD (SHEET 5 OF 6) Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 23, 2010 747-25A3581Revision 2 September 11, 2012 31 of 63 BOEING SERVICE BULLETIN 747-25A3581

ALERTALERT

More DataQtyIdentificationNameTaskStep STA 400 bulkhead1284U1363-4BRACKET - DRIP

SHIELD MOUNTING Remove9 STA 400 bulkhead2-FASTENERRemove

(a) Fill holes 2 (STA 400 bulkhead).

Flush is not required.

2BACR15BA5AD4CRIVET, 100 DEGInstall (New) At STA 360, (a) (c)3-NUTPLATERemove10 At STA 380, (a) (c)3-NUTPLATERemove

(a) Apply Alodine 1200 conversion coating and corrosion inhibiting compound (BMS3-27). Refer to SOPM 20-43-03 and 747-400SF SRM Chapter 51 as accepted procedures.

(b) Loosen the drain tube clamp(s) from the supporting standoff as needed.

(c) Fill #40 rivet holes with AD material after removing nut plates.

FIGURE 1: ELECTRONICS EQUIPMENT CENTER - REMOVAL OF EXISTING DRIP SHIELD (SHEET 6 OF 6) Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 23, 2010 747-25A3581Revision 2 September 11, 2012 32 of 63 BOEING SERVICE BULLETIN 747-25A3581

ALERTALERT

Page 33OCROpen in PDF

BOEING SERVICE BULLETIN 747-25A3581

ALERT ALERT STA 400 STA 380 STA 360 1962728 FIGURE 2: ELECTRONICS EQUIPMENT CENTER - LOOSEN AFFECTED WIRE BUNDLES (SHEET 1 OF 4) Original Issue: September 23, 2010 Revision 2 September 11, 2012 Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished 747-25A3581 Work - See page 1 for details. 33 of 63

Page 34OCROpen in PDF

BOEING SERVICE BULLETIN 747-25A3581

ALERT ALERT STA 400 STA 380 LBL 40 LBL STA 400

BULKHEAD

WIRE BUNDLES NOT SHOWN FOR CLARITY 1961527 FIGURE 2: ELECTRONICS EQUIPMENT CENTER - LOOSEN AFFECTED WIRE BUNDLES (SHEET 2 OF 4) Original Issue: September 23, 2010 Revision 2 September 11, 2012 Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished 747-25A3581 Work - See page 1 for details. 34 of 63

Page 35OCROpen in PDF

BOEING SERVICE BULLETIN 747-25A3581

ALERT ALERT STA 400

BULKHEAD LBL 30

WIRE BUNDLES NOT SHOWN FOR CLARITY LBL 40 1961528 FIGURE 2: ELECTRONICS EQUIPMENT CENTER - LOOSEN AFFECTED WIRE BUNDLES (SHEET 3 OF 4) Original Issue: September 23, 2010 Revision 2 September 11, 2012 PROPRIETARY - Copyright © Unpublished Export Controlled ECCN: 9E991 - BOEING 747-25A3581 Work - See page 1 for details. 35 of 63

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY numbers shown below are the number of parts necessary for this figure.

More DataQtyIdentificationNameTaskStep

FORWARD SIDE OF STA 400 BULK- HEAD --WIRE BUNDLESLoosen1

REMOVE CLAMPS

AND ASSOCIATED

HARDWARE AT

LOCATION AS SHOWN.

-BACC10DK12CLAMP, LOOPRemove2 -BACC10DK12CLAMP, LOOPRemove / Keep3 FIGURE 2: ELECTRONICS EQUIPMENT CENTER - LOOSEN AFFECTED WIRE BUNDLES (SHEET 4 OF 4) Export Controlled ECCN: 9E991 - BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.

Original Issue: September 23, 2010 747-25A3581Revision 2 September 11, 2012 36 of 63 BOEING SERVICE BULLETIN 747-25A3581

ALERTALERT

Pages 37–48 of 63