TCDS P20NE

DEPARTMENT OF TRANSPORTATION P20NE FEDERAL AVIATION ADMINISTRATION Revision 13 Hartzell HC-E5 TYPE CERTIFICATE DATA SHEET NO. P20NE September 18, 2024 Propellers of models described herein conforming with this data sheet (which is part of Type Certificate No. P20NE) and other approved data on file with the Federal Aviation Administration meet the minimum standards for use in certificated aircraft in accordance with pertinent aircraft data sheets and applicable portions of the Federal Aviation Regulations provided they are installed, operated and maintained as prescribed by the approved manufacturer’s manuals and other approved instructions. Type Certificate Holder Hartzell Propeller LLC Piqua, OH 45356 Type Certificate Holder Record Hartzell Propeller Inc. Piqua, OH 45356 Type Constant speed; hydraulic (see Notes 3 and 4) Engine shaft Special flange (see Note 1) Hub material Aluminum Alloy Blade material See below Number of blades Five Hub models HC-E5A-2,-3, -31; HC-E5B-5; HC-E5N-3,-5; HC-E5P-3, HC-E5W-3 (See Notes 1 and 4) Maximum Diameter Approx. Max. Wt. Complete Blades Continuous Takeoff Limits (For Reference Only) Notes (see Note 2) HP RPM HP RPM (see Note 2) (See Notes 3 and 7) (See Note 10) HC-E5N-3 E8218-0 850 2200 850 2200 85” to 75” 179 lb. Aluminum Alloy to E8218-10 (-0 to -10) E8492-0 950 2000 950 2000 86.5” to 76.5” 184 lb. Aluminum Alloy to E8492-10 (-0 to -10) NC8834-0 950 2000 950 2000 91” to 81” 152 lb. Carbon Composite to NC8834-10 (-0 to -10) HC-E5B-5 E12902 1645 1390 1645 1390 132” 168 lb. Aramid Composite HC-E5A-2 E9193 1650 2000 1650 2000 94” 175 lb. Carbon Composite HC-E5A-3, HC-E5A-31 NC10245-0 1200 1700 1200 1700 105” to 95” 153 lb. Carbon Composite to NC10245-10 (-0 to -10) NC10320-0 1200 1700 1200 1700 106” to 96” 154 lb. Carbon Composite NC10320-10 (-0 to -10) HC-E5P-3 NC10245-0 1200 1700 1200 1700 105” to 95” 153 lb. Carbon Composite to NC10245-10 (-0 to -10) NC10320-0 1200 1700 1200 1700 106” to 96” 154 lb. Carbon Composite to NC10320-10 (-0 to -10) HC-E5N-5 NC10905-0 1100 1591 1100 1591 112” to 102” 168 lb. Carbon Composite to NC10905-10 (-0 to -10) HC-E5W-3 NC9405-0 1000 1900 1000 1900 97” to 87” 153 lb. Carbon Composite to NC9405-10 (-0 to -10) P20NE, Revision 13 Page 2 of 4 Certification Basis: 14 CFR Part 35 effective October 14, 1980 with amendments 1 through 5. Type Certificate No. P20NE issued December 18, 1989 under Delegation Option Authorization procedures of FAR Part 21 Subpart J. Date of application for Type Certificate: October 25, 1989. Models approved to the original certification basis include the following: HC-E5N-3 Models added, updated or revised in accordance with 14 CFR Part 35 effective August 18, 1990 with amendments 35-1 through 35-6 include the following: HC-E5B-5 HC-E5A-2 approved October 29, 2004 to 14 CFR Part 35 effective August 18, 1990 with amendments 1 through 6 and Special Conditions no. 35-002-SC as published in the Federal Register Vol. 66, no. 192, Docket no. NE124 on October 3, 2001. The following models were added, updated or revised in accordance with 14 CFR Part 35 with amendments 35-1 through 35-9 effective March 19, 2013: HC-E5N-3 Models added after August 31, 2009 are approved in accordance with Organization Designation Authorization procedures of 14 CFR Part 183 Subpart D: The following models were added, updated or revised in accordance with 14 CFR Part 35 with amendments 35-1 through 35-9A effective July 26, 2013: HC-E5A-3, HC-E5P-3 The following models were added, updated or revised in accordance with 14 CFR Part 35 with amendments 35-1 through 35-10 effective August 30, 2017: HC-E5N-5, HC-E5P-3, HC-E5A-31, HC-E5W-3 Production Basis: Production Certificate no. 10 Note 1: Hub Model Designation (See Notes 4 and 5) HC - E 5 N - 3 A Character when used denotes a minor change not affecting interchangeability or eligibility L when used denotes left-hand rotation Denotes specific design features -2: no beta feedback mechanism -3: external beta feedback mechanism with hydro-mechanical interface -31: external beta feedback mechanism with electrical interface -5: internal beta feedback mechanism N denotes flange with eight 9/16” bolts and two ½” dowels on a 4.25” bolt circle A denotes flange with twelve 9/16” bolts and two 5/8” dowels on a 5.125” bolt circle B is identical to A except for dowel position W is similar to N except uses studs in place of bolts Number of blades Identifies basic design Hartzell Controllable Page 3 of 4 P20NE, Revision 13 Note 2: Blade Model Designation (See Notes 5 and 6) E 82 18 A K - 2 Number of inches cut off from (or added to if +) basic diameter B or K denotes deicing boots S when used with aluminum blades denotes a shot-peened exterior Any other character denotes a minor modification not affecting eligibility Basic model or template Basic diameter in inches. Add three inch correction for all blade models. Blade shank configuration: E denotes right hand tractor NC denotes right hand tractor composite blade with counterweight HE or HNC denotes right-hand pusher LE or LNC denotes left-hand pusher JE or JNC denotes left-hand tractor Note 3: Pitch Control (weight of pitch control extra) (See Notes 4 and 10) (a) Maximum output pressure: 700 psig (b) All propeller models have counterweighted blades and use governor oil to decrease pitch. (c) The Hartzell propeller model HC-E5A-2 with E9193 blades is controlled by an integrated control system which is part of the engine type design. The propeller model HC-E5A-2 with E9193 blades complies with the propeller airworthiness requirements when used with the Pratt & Whitney PT6A-68B engine only. Any change to the engine, including its control system, which affects or may affect the propeller approval must be substantiated to demonstrate that the propeller as integrated with the changed engine, including its control system, still complies with the propeller certification basis. Also, any change to the engine resulting from a change to the propeller must be substantiated to demonstrate that the changed engine still complies with the engine certification basis. Maximum output pressure for the HC-E5A-2 propeller model: 700 psig. (d) Hartzell propeller model HC-E5A-31( ) is controlled by an integrated electronic system which is part of the engine type design. Propeller model HC-E5A-31( ) complies with the propeller airworthiness requirements when used only with the Pratt & Whitney PT6E-67XP series engine, whose electronic software is written based on inputs from Hartzell’s dynamic simulation models. Any changes to the engine or propeller, including its control system, which affects or may affect the propeller or aircraft approval must be substantiated to demonstrate that the propeller as integrated with the engine, including its control system, still complies with the propeller and the engine certification basis. (e) All governors and propeller control systems must be approved as part of the aircraft installation regardless of manufacturer. (see Note 10) Note 4: Feathering (a) The -2, -3 and -5 models incorporate feathering and unfeathering features. Reversing (a) The -3 and -5 models are approved for installation as reversing propellers with appropriate reversing controls. (b) The -2 models do not reverse. Note 5: Left-Hand Models (see Notes 1 and 2) The left-hand version of an approved propeller model is approved at the same rating and diameter as listed for the right-hand model. P20NE, Revision 13 Page 4 of 4 Note 6: Interchangeability (See Note 2) (a) Shot-peened blades may replace non shot-peened blades either individually or as a set. (b) Refer to Hartzell Service Letter HC-SL-30-260 for ice protection system component interchangeability. Note 7: Accessories (a) Propeller spinner. (weight of spinner extra) (1) Approved with Hartzell and other manufacturers’ spinners when listed on Hartzell type design data. (2) All propeller spinners must be approved as part of the aircraft installation regardless of manufacturer. (See Note 10) (b) Propeller deicing (weight of deicing equipment extra) (1) Approved with Goodrich electrical deicing kit 5EXXXX-X, 7EXXXX-X, 65-XXX, 67-XXX, or 77- XXX when the specific kit number is listed on Hartzell type design data and installed in accordance with Goodrich Report no. ATA 30-60-07. (2) Approved with Safeway deice equipment when installed in accordance with Safeway Installation Manual, Hartzell Manual 133( ) for aluminum blades or Manual 135( ) for composite blades, and associated STC or PMA documentation. (3) Propeller models listed in this data sheet are approved for use with propeller ice protection equipment listed in Hartzell Manual 159( ) or in other Hartzell type design data. (4) All propeller ice protection equipment must be approved as part of the aircraft installation regardless of manufacturer. (See Note 10) (c) Propeller pulley drive. (weight of pulley drive extra) (1) Propeller model HC-E5A-2 with blade model E9193 is approved with Pilatus Aircraft Ltd. air conditioning system pulley drive P/N 521.55.21.002. Note 8: Shank Fairings Not applicable. Note 9: Special Limits Not applicable. Note 10: Propeller installation must be approved as part of the aircraft Type Certificate and demonstrate compliance with the applicable aircraft airworthiness requirements. Propeller models listed herein consist of basic hub and blade models. Most propeller models include additional characters to denote minor changes and specific features as explained in Notes 1 and 2. Refer to the aircraft Type Certificate Data Sheet for the specific propeller model applicable to the installation. Propellers with composite blades must be evaluated for bird impact resistance prior to approval on any type aircraft. Hartzell Propeller must perform tests and/or analyses based on aircraft configuration and operating conditions to determine the potential hazard as a result of a bird impact. Note 11: Special Limits (a) Life Limits and Mandatory Inspections (1) Airworthiness limitations, if any, are specified in Hartzell Manuals 147 and 149. (2) The propeller Certification Branch Office must evaluate the propeller installation for each new aircraft installation to assess possible changes in the airworthiness limitations. Note 12: Special Notes (a) Refer to Hartzell Manual no. 202( ) for overspeed and overtorque limits. (b) Refer to Hartzell Service Letter HC-SL-61-61( ) for overhaul periods. END