- Holder
- Carson Helicopters Inc.
- Revision
- 0
- Revised
- August 6, 2009
- Status
- Current
- Product
- Aircraft · Rotorcraft
- Certification basis
- Part 1, Part 21, Part 36, Part 45, Part 91, Part 133, Part 137
- Models
- 1
- Registered
- 2 aircraft
The release keeps the latest revision of each data sheet. Model names are as the data sheet lists them.
On this page
Models · 1
| Model | Also known as | Note |
|---|---|---|
| SH-3H |
Airworthiness directives · 0
ADs whose products are models on this data sheet, matched by model and maker.
No ADs matched this data sheet’s models
Registered aircraft
Registry models that point at this data sheet, with their registered aircraft.
STCs approved under this data sheet · 8
STC SR00206NYInstallation of 11,000 pound capacity Cargo SlingSTC SR04401NYIncrease of Out of Ground Effect (OGE) Hover PerformanceSTC SR04122NYThe Installation of Carson Helicopters, Inc. Composite Tail Rotor Blade and Pitch Sleeve, part number 428-600-1,STC SR04160NYInstallation of Comm/Nav/SurveillanceSTC SR04159NYInstallation of EFIS/EICASSTC SR02671LAInstallation of a shorter composite bladeSTC SR01755SEInstallation of the Main Rotor Head ModificationSTC SR01427SEInstallation of S-61L fixed main landing gear
What the data sheet says
From the PDF’s text layer, line by line: tables lose their columns. The PDF is the record.
Page No. 1 2 3 4 5 6
Rev. No. - - - - - -
DEPARTMENT OF TRANSPORTATION
FEDERAL AVIATION ADMINISTRATION
R00014LA
Carson Helicopters, Inc.
SH-3H
August 6, 2009
TYPE CERTIFICATE DATA SHEET NO. R00014LA
This data sheet, which is a part of the Type Certificate R00014LA, prescribes conditions and limitations under
which the product for which the type certificate was issued meets the airworthiness requirements of the 14 Code of
Federal Regulations (14 CFR).
Type Certificate Holder: Carson Helicopters, Inc.
952 Blooming Glen Road
Perkasie, PA 18944
I - Model SH-3H (Restricted Category Rotorcraft) Approved August 6, 2009.
Engines (2) General Electric T58-GE-402
Fuel ASTM-D1655 (Jet A, Jet A-1, Jet B); JP4 or JP5 (General Electric Co. Spec. No.
D50T1011 or subsequent revisions thereto). (See Note 13)
Engine Limits Engine Limits For T58-GE-402 (see Note 14 for horsepower)
Rating
Torque
(%Q)
Power
Turbine
Speed
(%Nf)
Gas
Generator
Speed
(%Ng)
Turbine
Inlet
Temp.
(T5 ºC)
Take-Off (10 Min.) 103% --- <103.7% 750º
One Engine Inoperative
30 Min.
103%
---
<103.7%
727º
Maximum Continuous (See
Note 15)
86% --- 101.8% 691º
Overspeed (Any Time
Period. (See Note 16)
106% --- 108% ---
Oscillations (See Note 17) --- --- 1% ---
Starting
Normal
(Momentary*)
Min. For Normal Start
For Battery Start
21%
19%
14%
950º
Acceleration or Compressor
Stall (Momentary*)
--- --- --- 950º
Stabilized or Slow Transient
(20 Sec.)
--- --- --- 780º
Ground Idle --- --- 56 ±3 % 575º
R00014LA Page 2 of 7
Page No. 1 2 3 4 5 6
Rev. No. - - - - - -
Engine Limits- * A transient high-temperature condition is one of brief duration in which the
temperature Continued peaks and falls off, either automatically or through the corrective action of the pilot.
The torque may exceed 103% Q on one engine to a maximum of 123% provided that the
power of the other is reduced so that total torque for both engines is not over 206% Q for
30 minutes or 172% continuously, and that the single-engine Ng, T5, and Q limits are not
exceeded. The governing parameter is the limit that occurs first.
Any time Ng exceeds 106%, the event and its duration must be recorded.
Maximum oil consumption rated during operation is 12 ounces per hour.
Refer to Carson Helicopters, Inc., CAR-110, “SH-3H Rotorcraft Flight Manual”, dated
August 4, 2009
Rotor Limits Normal 91% to 112.5%
Maximum 117%
Transmission Torque See Engine Limits and Notes 14 and 15
Limits
Airspeed Limits V ne (Never exceed) speed 120 knots IAS.
Other Limits None
Center of Gravity Most Forward C.G. (+258.0) to (+259.6) at 19,100 to 21,000 lbs.
(C.G. Range) Most Aft C.G. (+276.0) to (+275.2) at 19,100 to 21,000 lbs.
(+254.0) to (+280.0) at 16,000 lbs. or less
Straight Line Variation Between Points Given. (See Chart)
21,000-
Gross Weight
(Lbs) 19,100-
16,000-
________________________________________
254 258 276 280
Inches From Datum
Refer to Carson Helicopters, Inc. CAR-110 “SH-3H Rotorcraft Flight Manual”,dated
August 4, 2009. Proper loading shall be determined by use of NAVAIR 01-1B-50,
Technical Manual USN Aircraft Weight and Balance Control. (See Note 1)
Empty Weight (C.G.) None
Datum 267.4 inches forward of main rotor centroid.
Leveling Means Leveling plat es on sill and upper frame of cargo door. Leveling procedures contained in
Dept. of Navy NAVAIR 01-230HLH-2-3.1, Technical Manual, Organizational
Maintenance, General Maintenance, Ground Handling, and Servicing Navy Model SH-
3H/UH-3H and NAVAIR 01-1B-40, Technical Manual Weight and Balance Data.
Maximum Weight 21,000 lbs.
Page 3 of 7 R00014LA
Page No. 1 2 3 4 5 6
Rev. No. - - - - - -
Minimum Crew 2 - Pilot and Copilot.
Number of Seats 11 – (2) at Sta. +147.0 Pilot and Copilot; (3) at Sta. +283.0 Left Side, (3) at Sta. +283.0
Right Side, (3) at Sta. +353.0 Left Side Aft (Fold Down Crew Member Seats).
Number of Passengers None
Maximum Cargo Refer to Carson Helicopters, Inc. CAR-110 “SH-3H Rotorcraft Flight Manual”, Note 7.
Fuel Capacity 848 Gal. Total (347 Gal. at Sta. 215.3, 148 Gal. at Sta. 263.7, 353 Gal. at Sta. 317.3).
(Trapped/Unusable 6.1 Gal.)
Oil Capacity 5.4 Gal. (2 tanks 2.7 Gal. each at Sta. 181.0). (Trapped/unusable 0.67 Gal. Ref.
NAVAIR 01-1B-40 Chart A)
Rotor Blade & Control For rigging information, See Note 4.
Movements
Serial No. Eligible Refer to Carson Helicopters, Inc. Report No. CAR-104, Serial Numbers Approved, N.C,
dated March 31, 2009, or later FAA approved revision. A current copy is on file at the
Los Angeles ACO.
Certification Basis 14 CFR 21.25(a)(2) effective February 1, 1965, with Amendments 21-1 through 21-42.
Type Certificate No. R00014LA issued on August 6, 2009 for the Special Purpose(s) of:
(1) Agricultural Operations under 14 CFR 21.25(b)(1).
Note: In accordance with 14 CFR 36.1(a)(4 ), compliance with the noise requirements
was not shown. Therefore, aircraft certificated under this type certificate are only
eligible for agricultural operations excepted by 14 CFR 36.1(a)(4) and defined under 14
CFR 137.3
(2) Forest and Wildlife Conservation Operations under 14 CFR 21.25(b)(2).
Note: In accordance with 14 CFR 36.1(a)(4), compliance with the noise requirements
was not shown. Therefore, aircraft certificated under this type certificate are only
eligible for aerial dispensing of liquids excepted by 14 CFR 36.1(a)(4) and defined under
14 CFR 137.3
(3) External Load Operations under 14 CFR 21.25(b)(7).
Note: In accordance with 14 CFR 36.1(a)(4), compliance with the noise requirements
was not shown. Therefore, aircraft certificated under this type certificate are only
eligible for external load operations excepted by 14 CFR 36.1(a)(4) and defined under 14
CFR 133.1(b).
General Note: Any alteration to the aircraft for Special Purposes not identified above
requires further FAA approval and in addition may require noise and /or flight testing.
Production Basis None. No helicopters may be produ ced under this approval. Prior to adding serial
numbers to this Type Certificate, each candidate helicopter must pass a conformity
R00014LA Page 4 of 7
Page No. 1 2 3 4 5 6
Rev. No. - - - - - -
inspection. The conformity inspection will be conducted in accordance with a Type
Inspection Authorization, Part 1, or Request for Conformity that will include as a
minimum, the inspections contained in the FAA Order 8110.56, Restricted Category
Type Certification, N.C., dated February 27, 2009, or later FAA approved revisions.
Also, a check by the type certificate holder of the flight characteristics in accordance
with all applicable portions of NATOPS Functional Check Flight Checklist NAVAIR 01-
230HLH-1F as appropriate for each aircraft, or other FAA approved manual.
Equipment The basic required equipment necessary for the particular special purpose operation must
be installed for certification. Each helicopter is required to incorporate modifications as
specified in:
1. Carson Helicopters, Inc. Engineering Configuration Report No. CAR-101, Rev. 1,
dated May 22, 2009, or later FAA approved revisions.
2. U.S. Navy External Cargo Hook P/N S6152-62100-1 as part of the military
configuration.
NOTES
NOTE 1. A current weight and balance report including a list of equipment included in the
certificated empty weight, and loading instructions when necessary, must be provided for
each aircraft at the time of original airworthiness certification and at all times thereafter.
1. Refer to Carson Helicopters, Inc. CAR-110, SH-3H Rotorcraft Flight Manual, dated
August 4, 2009.
2. Refer to Dept. of Navy NAVAIR 01-1B-50 Technical Manual USN Aircraft Weight
and Balance Control, Initial Release, dated October 1, 1990.
3. Carson Helicopters, Inc. Weight and Balance Report No. CAR-106, N.C., dated
March 31, 2009, or later FAA approved revisions.
NOTE 2. The following placards, Carson Helicopter s, Inc. Drawing No. CAR-1001, N.C., dated
January 9, 2009, or later FAA approved revisions, must be prominently displayed in the
cockpit in full view of the pilots.
Placard No. 1
"THIS ROTORCRAFT MUST BE OPER ATED IN ACCORDANCE WITH THE
RESTRICTED CATEGORY OPERATING LIMITATIONS OF 14 CFR part 91 §
91.313."
Placard No. 2
“THIS HELICOPTER MUST BE OPERATED IN COMPLIANCE WITH THE
OPERATING LIMITATIONS SPECIFIED IN THE APPROVED HELICOPTER
OPERATORS MANUAL. REFER TO CARSON HELICOPTERS, INC. CAR-110, SH-
3H ROTORCRAFT FLIGHT MANUAL FOR OPERATING LIMITS AND
RESTRICTIONS.”
Placard No. 3
“EXTERNAL LOADS OPERATIONS: Vne WILL BE DETERMINED FOR EACH
PROPOSED EXTERNAL LOAD APPLICATION.”
Placard No. 4
"VFR OPERATIONS ONLY."
Page 5 of 7 R00014LA
Page No. 1 2 3 4 5 6
Rev. No. - - - - - -
NOTE 3. The builder’s data plate required by 14 CFR part 45 § 45.13 must be installed in
accordance with Carson Helicopters, Inc. Drawing No. CAR-1002, N.C., dated January
9, 2009, or later FAA approved revisions.
NOTE 4. The helicopter(s) must be serviced, maintained, inspected, repaired, and overhauled in
accordance with the requirements and documents specified in Carson Helicopters, Inc.
Instructions for Continued Airworthiness Report No. CAR-102, Rev. 1, dated May 21,
2009, or later FAA accepted revisions, or inspected in accordance with other FAA
accepted inspection programs. The service life limited parts overhaul and retirements
intervals for these helicopters is specified in Carson Helicopters, Inc. Instructions for
Continued Airworthiness Report No. CAR-102, Rev. 1, dated May 21, 2009, or later
FAA approved revision. A FAA approved copy must accompany each helicopter on
delivery. The TC Holder’s Instructions for Continued Airworthiness Report is part of the
TC Holder’s Instructions for Continued Airworthiness.
NOTE 5. The helicopter must be operated in acco rdance with Carson Helicopters, Inc. CAR-110,
SH-3H Rotorcraft Flight Manual, dated August 4, 2009.
NOTE 6. Prior to civil airworthiness certification, Carson Helicopters, Inc. Report No. CAR-101
Engineering Configuration Report, Rev. 1, dated May 22, 2009, or later FAA approved
revisions, must be incorporated.
NOTE 7. This aircraft is prohibited from carrying cargo for compensation or hire. Carriage of
cargo is limited to such cargo that is incidental to the aircraft owner/operator’s business
which is other than air transportation.
NOTE 8. Restricted Category aircraft may not be operated in a foreign country without the express
written approval of that country.
NOTE 9. This aircraft has not been shown to meet the requirements of the applicable
comprehensive and detailed airworthiness code as provided by Annex 8 to the
Convention on International Civil Aviation.
NOTE 10. Military to Civil or Military to Military engine changes are allowed provided the
replacement engine is of the same make and model as identified in this TCDS. The
military or civil replacement engine must have proper military or civil records and have
the applicable FAA Airworthiness Inspec tion accomplished and be in an airworthy
condition.
NOTE 11. The Airworthiness Directives and Departme nt of Navy Safety of Flight (SOF) messages
for the helicopter and engines contained in Carson Helicopters, Inc. Report No. CAR-
105, Airworthiness Directives Compliance, N.C., dated December 4, 2008, or later FAA
approved revisions, must be complied with prior to original airworthiness certification.
NOTE 12. No person may be carried in this helicopter during flight unless that person is essential to
the purpose of the flight. For additional mission configurations see Carson Helicopters,
Inc. CAR-101 Engineering Configuration Report, Rev. 1, dated May 22, 2009 or later
FAA approved revisions.
NOTE 13. Alternative and emergency fuels are listed in Carson Helicopters, Inc. CAR-110, SH-3H
Rotorcraft Flight Manual, dated August 4, 2009.
R00014LA Page 6 of 7
Page No. 1 2 3 4 5 6
Rev. No. - - - - - -
NOTE 14. Total power for two engine operation is limited to 2,500 hp (103% torque). For takeoff,
maximum continuous total power for two engine operation is limited to 2,100 hp (86%
torque). These engine power limitations are due to the main gearbox rating.
NOTE 15. The 86% Engine Torque limit is due to the maximum continuous main gearbox rating.
NOTE 16. Over-speed limits for the T58-GE-402 engine:
108% N g not to exceed 15 seconds.
If less than 15 seconds corrective action is required to bring RPM within limits.
If more than 15 seconds, over-speed inspection is required.
NOTE 17. For the T58-GE-402 engine: Maximum allowa ble at all power levels (± 1%); oscillations
may be higher in access drive mode. Limits do not apply during auto-rotations.
NOTE 18. In addition to the standard helicopter re quirements, the following additional data and/or
helicopter configuration requirements must be met for each individual Carson
Helicopters, Inc. model SH-3H helicopter upon application for an original Special
Airworthiness Certificate:
1. A completed Application for Airworthiness Certificate, FAA Form 8130-6 that
correctly identifies the type certificate holder’s helicopter and its intended special
purpose(s).
2. Written confirmation from the certifying office that the affected serial number has
been added to this Type Certificate.
3. The application for airworthiness certification and the helicopter’s registration
certificate must match the information of the Carson Data Plate.
4. The documents specified in Section III of the FAA accepted Carson Helicopters, Inc.
Instructions for Continued Airworthiness Report CAR-102, Rev. 1, dated May 21,
2009, or later FAA accepted revision, are with the helicopter.
5. The conditions and limitations specified in this Type Certificate Data Sheet are met.
NOTE 19. Helicopters that do not have documentation showing they were surplused from an Armed
Force of the United States are not eligible for certification under this type certificate.
Helicopter(s), engine(s), and appliances that have records indicating time-in-service by a
foreign military or a foreign government will be presumed to be ineligible for
certification or installation under this type certificate. This presumption may be
overcome by the applicant substantiating, to the satisfaction of the FAA, through
documents, tests,
computations, evaluations, analyses, or other means or methods that the helicopter,
engine, or appliance, during its time-in-service by the foreign military or foreign
government, was maintained by an extent and in a manner equal to that of an Armed
Force of the United States.
NOTE 20. Carson Helicopters Inc. did not necessarily comply with standard category airworthiness
design and airworthiness standards, under restricted category certification.
NOTE 21. Any changes to the type design of this helicopter by means of an amended type
certificate (TC), supplemental type certificate (STC), or amended STC, requiring
instructions for continued airworthiness (ICA’s) must be submitted through the project
certification office for review and acceptance by the Fort Worth – Aircraft Evaluation
Group (FTW-AEG) prior to the aircraft delivery, or upon issuance of the first
airworthiness certificate for the affected aircraft, whichever occurs later as prescribed by
Title 14 CFR 21.50.
Page 7 of 7 R00014LA
Page No. 1 2 3 4 5 6
Rev. No. - - - - - -
---------------------------------------------------------------- END ---------------------------------------------------------- ------