AC Page MG 16 - 5 be assessed using the type and model of NVG that the operator will use in their NVG operations.
(5) Installation Design .
(i) Mechanical Installation. Airc raft modifications should be made to (1) ensure compliance with the airworthiness regulations and (2) comply with the equipment manufacturer’s recommendations. The designer should observe good engineering practices, in specifying material type, wire routing, fastener type, light switches and controls, edge distance, and ergonomic considerations (§§ 29.777,
29.1307, 29.785, and 29.1359).
(ii) Arrangement and Visibility. T he mounting position of all instruments, switches, position labels, and controls should be visible to the pilot during unaided and aided flight and in all cockpit lighting conditions (day and night). Technical Standard Order (TSO) approval does not assure instruments will be acceptable in a particular cockpit installation or for all lighting conditions. The instruments, switches, and placards should be free from reflections. Warning, caution, and advisory annunciation devices should be conspicuous, NVG compatible, and clearly visible to the pilot (day and night).
Gauge and instrument markings should be clearly seen and the colors of the markings maintained. (See §§ 29.771, 29.773, 29.777, 29.811, 29.853, 29.1303, 29.1321,
29.1322, 29.1381, 29.1555, 29.1557 and 29.1559, RTCA DO-275, and Advisory Circular 20-69.)
(iii) Interior Lighting. Internal lighting systems should not adversely affect the performance of the NVIS. Instrument markings and illuminated instrument markings must comply with § 29.1381 and AC 20-88 and should be demonstrated during aided and unaided operations. Colors should be uniform (different shades of red/amber/green are not acceptable) to avoid confusion. For example, different shades of red (NVIS red and aviation red) within the cockpit have not been accepted. Additionally, NVIS red with orange hue has not been accepted in cockpits with amber caution lights/indicators.
(iv) Exterior Lighti ng. External lighting systems should not adversely affect the performance of the NVIS. Compliance with §§ 29.1383 to 29.1401 and AC 20-74 should be demonstrated. External lighting should be evaluated under probable terrain, illumination, and environmental operating conditions (e.g., rain, snow, fog, dust, etc.). Consider modifying position lights with NVIS compatible lights. There are NVIS-compatible position lights available. Non-NVIS compatible position lights can cause unacceptable shadowing and interference with NVG performance in dark areas where there is little or no cultural lighting.
(v) Reflections and Glare. There should be no glare or reflections that interfere with unaided or NVG aided operations. Sources of reflection and glare could include aircraft interior surfaces (floor, panels, etc.), equipment, seats, etc. Compliance with §§ 29.771, 29.773, and 29.1381 should be demonstrated in the ground and flight test.
AC 29-2C, Chg 2 4/25/06 Page MG 16 - 6
(vi) Controls.
(A) NVIS lighting controls shoul d be readily identifiable and accessible.
(B) NVIS control design should mi nimize the probability of the inadvertent selection of incompatible light sources in the cockpit. The detrimental effects of incompatible light sources on the external view through the NVG should be minimized if there is a capability to select an NVIS incompatible light source
(C) NVIS Lighting should have a dimming range consistent with aided and unaided operations. Compliance with §§ 29.777, 29.1301, 29.1309, and 29.1381 should be demonstrated.
(D) Some installations incorporate master light switches to control special busses for the lighting systems. If this capability is provided, it should be evaluated to assure failure modes are not introduced that will result in the illumination of incompatible light sources or loss of all required lighting (§§ 29.1307 and 29.1367).
(E) Compliance with §§ 29.777, 29.1301, 29.1309, and 29.1381 should be demonstrated.
(vii) NVIS Power Sources. Determi ne whether the electrical power source capacity is adequate for the system installation under all foreseeable operating conditions including engine failure. Duplicate systems should be powered from separate busses and, in some cases, from independent sources if required by the airworthiness regulations (§§ 29.1309 or 29.1351).
(viii) Cooling Test. Systems and components that are added or modified
(e.g., addition of filters to light sources) for NVIS operations should be tested in accordance with AC 29.1309 (cooling test procedures) for continued acceptability. This is important because the installation of a filter could result in an appreciable increase in a system or component temperature. This issue would be most critical for a system that remained brightly illuminated during daylight operations.
(6) NVIS Cockpit and NVG Integration:
(i) Accessibility and Workload.
(A) The NVIS configuration should not compromise the ability to perform all necessary duties. Scanning and control accessibility should be considered. The applicant should determine the representative flight profiles and environmental conditions under which the workload should be evaluated. The purpose of this evaluation is to ensure that the workload associated with NVIS operations does not compromise safety of flight. Compliance with §§ 29.771, 29.773, 29.777, and 29.1523 should be demonstrated.
AC Page MG 16 - 7
(B) The rotorcraft characteristics need to be such that the workload is acceptable and the required instruments are within the pilot’s primary scan when using NVGs. The design of the NVIS should consider flight into inadvertent instrument meteorological conditions (IMC) and unusual attitude recovery. Inadvertent IMC is defined for these purposes as loss of visual references, such as actual IMC, brownout, whiteout, etc. It is important to assess the transition from aided flight to instrument flight. Therefore, the applicant should plan this evaluation during all requested phases of flight (such as cruise flight or takeoff and landing, if requested).
(C) Assess the NVIS lighting fo r readability, uniformity, balance, light leakage, reflections, and degradation of NVG performance. An NVIS and NVG Cockpit integration checklist is provided at:
http://www.faa.gov/aircraft/air_cert/design_approvals/rotorcraft/nvis/.
Also, RTCA DO-275, Section 4.0, provides an expanded explanation.
(D) NVGs shall be TSO-C164 compliant. A cockpit evaluation should be accomplished with NVGs that meet the minimum TSO-C164 standards as well as NVGs the applicant intends to use in operations (if they exceed TSO-C164 standards). In no case will NVG’s that do not meet or exceed TSO-C164 standards be approved for use in the cockpit.
(ii) Controls
(A) Accessibility of NVIS Lighting System Controls. Pilots should be able to readily identify, access, and operate, with one hand, the NVIS lighting controls inflight from their normal seated position.
(B) Inadvertent Actuation of Cont rols. Appropriate protection should be provided to minimize the possibility of the inadvertent actuation of NVG controls and non-NVIS light sources.
(iii) Visibility.
(A) Windscreen. The wind screen and transparencies should not decrease NVG light sensitivities more than 12% or one resolution element on a tri-bar chart. If the aircraft has a windscreen anti-ice function, the windscreen should be evaluated with anti-ice on and off to assess effect on the NVGs. Operation of windscreen anti-ice should follow manufacturer’s procedures and limitations.
(B) Glare and reflectivity. Gl are and reflectivity can be produced from internal and external light sources.
( 1 ) Internal light sources:
AC 29-2C, Chg 2 4/25/06 Page MG 16 - 8
( i ) Permissable reflections should be no worse than the original unaided lighting. However, NVGs may pick up more reflections than seen with unaided vision.
Those reflections should be blocked to ensure they do not interfere with the pilot’s ability to see outside the aircraft while wearing NVGs.
(ii) Glare can result from poor ly filtered or fitted lighting. Additionally, if there are non-NVIS compatible light sources in other areas of the aircraft, they can cause interference. Assess light sources causing glare and develop mitigating solutions to keep them from interfering with the pilots view through NVGs.
( 2 ) External Light Sources:
( i ) Usually, external light glare or refl ectivity is assessed during the night flight. Evaluating the effects of glare and reflections that interfere with NVGs from external aircraft lighting is very important when operating in remote, dark areas. There are NVIS compatible external aircraft lights available. Consider using them if operations are conducted in very dark areas where there is little to no ambient cultural lighting.
Methods to reduce glare or reflections caused by external aircraft lighting depend on where the light enters the cockpit and from what aircraft structure reflects the light. For example, light that reflects off of skids or wire cutters can be mitigated by use of nonreflective paint on the reflecting surfaces. Additionally, chin-bubble mats have been used to block light and reflections through the chin-bubble.
NOTE 6: If chin bubble mats are used, pay particular attention to:
(1) restrictions in the pilot's field-of -view through the chin bubble, particularly during take-off, landing, and hover operations, and
(2) the potential for the mat to be mov ed or dislodged during flight, thereby causing interference with the tail rotor pedals.
Use of chin bubbles mats should be evaluated during both ground and flight test.
NOTE 7: Some non-compatible lighting such as landing or taxi lights, search lights, etc.; can aid as well as hinder NVG operations. Their effects on NVGs in the specific helicopter flown should be assessed and recorded during integration evaluations.
(ii) Evaluation of external light sources t hat pilots could use to assist them with NVG flight should be evaluated for their effect on NVG performance. If the aircraft has landing lights, searchlights, or other lights that the pilots use, they should be assessed to evaluate their effect on the aided vision range. For instance, if the pilot uses a searchlight or landing lights to help assess landing area or while landing with NVGs, then the light’s effect on the range of vision within and beyond the light boundaries should be evaluated and documented.
AC Page MG 16 - 9
(iii) Sources of non-compatible light glare and reflections and any mitigating strategies developed should be recorded during integration evaluations.
(7) Ground and Flight Tests.
(i) The purpose of FAA certification tests is to verify that the rotorcraft meets the certification requirements for both aided and unaided operations. This will include an assessment of crew station(s) to ensure that the crew can effectively use all systems for both aided and unaided operations. These assessments may result in changes to the established limitations, or operating procedures of a rotorcraft (reference §§ 29.1581, 29.1583 and 29.1585). Appropriate flight test personnel should conduct the ground and flight tests.
(ii) Prior to requesting FAA certification flight tests, the applicant should submit the appropriate data, drawings, bench tests, component tests, environmental qualifications, installation configurations, and test equipment (including calibration) that were used to demonstrate compliance with the requirements to the appropriate certifying office. This will also include the manufacturer, type, and model of the NVG the applicant intends to use for NVIS operations.
(iii) Additionally, ground and flight te st plans should include the types of operations for which the applicant intends to use the aircraft. For instance, dual pilot operations or training will require both a right and left pilot seat evaluation. EMS operations will require an evaluation of visibility from the passenger compartment and cockpit protection from passenger compartment lighting if not NVIS compatible.
(iv) Once submitted, the FAA will review the package along with the certification plan to determine compliance. After certification package acceptance, the applicant should coordinate final approval for the test plan and test schedule. The test plan and schedule should include all proposed tests to show compliance. The checklists, found at http://www.faa.gov/aircraft/air_cert/design_approvals/rotorcraft/nvis/ outline a test sequence. Another acceptable method of demonstrating compliance is described in RTCA DO-275, Section 4.0, and Appendices. Upon test plan acceptance, prior to commencing any certification tests (ground or flight), a conformity inspection should be performed. Once the conformity is performed, any changes from the conformed configuration (e.g., removing filters or changing bulbs in light sources) may, at the FAA’s discretion, require another conformity inspection.
( v ) The applicant is responsible for providing the appropriate pre-test requirements and providing the FAA certification office with the following:
(A) A list of test equipment to perform test (tri-bar charts, illumination source, illumination measuring device, NVG test set, or NVG eye lane).
AC 29-2C, Chg 2 4/25/06 Page MG 16 - 10 (B) A description of the test facilities to be used (type of darkened location).
(C) A description of the flight area including cultural lighting, terrain, obstacles, and landing areas.
(D) Weather and illumination information including moon cycle, anticipated climatic conditions, etc.
(E) Any additional training necessary to operate in a NVIS environment (novel or new technology briefing).
(F) The flight equipment to be used (helmets, mounts, NVGs, flashlights, etc.).
( vi) Ground Test Procedures.
(A) To optimize the test program and minimize flight test risks, ground testing should be accomplished prior to flight test. This evaluation should be conducted from all crew stations intended to be used (including cabin) in NVG operations.
(B) Flight-testing should only be commenced when ground testing is satisfactorily completed. It is highly recommended that the schedule allow sufficient time between ground and flight test to resolve deficiencies discovered during ground testing. As a minimum, the NVIS/NVG Cockpit integration checklist should be completed. This checklist can be found at http://www.faa.gov/aircraft/air_cert/design_approvals/rotorcraft/nvis. Another acceptable test procedure and test sequence is provided in RTCA DO-275, Section
4.4.1, and Appendices.
(vii) Flight Test Procedures.
( A ) Flight test should be scheduled for a low illumination night (no moon) preferably in an area where there is little cultural lighting. Evaluation of NVG and NVIS lighting integration should not be conducted in high ambient light conditions because some of the effects of inadequate cockpit lighting and reflections or glare will be masked.
(B) Prior to commencing the flight test evaluation, a daylight familiarization flight of the flight test area should be performed. Any specific flight regimes, maneuvers, terrain, or landing areas that will be used for the NVIS evaluation should be flown to familiarize the test pilots with possible hazards in the test area.
(C) For single pilot ai rcraft, if it is determined that the normal configuration of the aircraft is required for the flight evaluation, it may not be possible to install dual controls. In this case appropriate training and authorization may be required for the
AC Page MG 16 - 11 FAA test pilot to conduct the in-flight evaluation. In addition, special test equipment may be installed during the evaluation to enhance flight test safety. If additional personnel are required for the evaluation, the appropriate crew stations will be installed.
(D) The flight test profile shoul d consist of maneuvers representative of those performed during normal or special operations over terrain and cultural areas in various illumination and weather conditions. This test should include evaluation under low illumination conditions (e.g., no moon, and overcast sky, with little cultural lighting).
As a minimum, the items in the flight test section should be completed. This can be found at http://www.faa.gov/aircraft/air_cert/design_approvals/rotorcraft/nvis. Another acceptable test procedure and test sequence is provided in RTCA DO-275, Section
4.4.2.
e. Rotorcraft Flight Manual (or Supplement).
AC 29-2C, Chg 2 4/25/06 Page MG 16 - 12
THIS PAGE INTENTIONALLY LEFT BLANK
AC Page MG 16 - 13 The following section is one template for use as a Rotorcraft Flight Manual Supplement (RFMS).
Other formats may be acceptable.
1. GENERAL
2. LIMITATIONS
2.1 Operational Limitations:
(NOTE 8: The following limitation is required in the RFMS verbatim.)
“Installation of this NVIS system does not approve or imply approval for flight operation with Night Vision Goggles (NVG). The Operator must receive approval from their FAA Flight Standardization District Office to operate with NVGs.”
2.2 Required Equipment in proper wo rking order for NVG Operations:
1. Helmet with NVG mount for each pilot using NVGs.
2. Night Vision Goggles that meet TSO-C164 or the minimum operation performance standards established in RTCA DO-275 for crewmembers using NVG.
3. Radar altimeter.
4. Slip/Skid indicator.
5. Gyroscopic attitude indicator.
6. Gyroscopic Direction Indicator or equivalent.
7. Vertical Speed Indicator or equivalent.
8. Communications and navigation equipm ent necessary for the successful completion of an inadvertent IMC procedure in the intended area of operations.
9. Any other aircraft or personal equi pment required for the operation i.e., curtains, extra batteries for NVGs, etc.
(NOTE 9: Some aircraft external lights cause distracting glare and reflections through the chin-bubble. If this is the case and chin-bubble mats are shown to be effective, consider adding the following note and the following caution:
“Chin bubble mats, if appropriate.”
AC 29-2C, Chg 2 4/25/06 Page MG 16 - 14
CAUTION:
If chin bubble mats are used to block glare from external aircraft lights, ensure that they are positioned and secured properly, provide sufficient view out of the chin bubble and do not block operation of tail rotor pedals.
2.3. Minimum Crew:
2.3.1. Additional crewmember use of NVGs during single-pilot operations into and out of unimproved sites:
2.3.1.1. Landing: An addition al crewmember shall be equipped with and use NVGs during landing to assist in obstacle identification and clearing.
2.3.1.2. Takeoff: An additional crewmem ber shall use NVGs during takeoff from unimproved sites to assist in obstacle identification and clearance if operational conditions permit (i.e., patient status, etc.) allows.
2.3.1.3. Enroute: An addi tional crewmember using NVGs is not required when the aircraft is above 300 feet AGL and in cruise flight.
2.4 Incompatible NVIS lights
Identify cockpit equipment and lighting particular to the installation that is, by design, not NVIS compatible and that should remain off during NVG operations (e.g., passenger cabin lighting, non-mission essential radios, etc.).
3. EMERGENCY AND MALFUNCTION PROCEDURES
3.1 NVG Malfunction or Failure
Transition from aided to unaided flight as required.
3.2 NVIS Lighting Malfuncti on or Failure in Flight.
Discontinue NVG use if the malfunction or failure degrades NVIS compatibility.
3.3 Aircraft Emergencies
Maintain aircraft control and then initiate RFM procedures. The pilot’s decision to continue use of NVGs should be based on the emergency situation.
4. NORMAL PROCEDURES
AC Page MG 16 - 15
4.1. Operational Procedures
4.1.1. Preflight .
•Check Windshield, windows, and chin bubble windows for suitability (scratches, grazing, cleanliness, etc.).
•Check NVIS lighting for light leakage and compatibility.
•NVG adjustment and alignment.
•Check function of additional NVIS equipment.
•Interior Configuration check for NVIS equipment (e.g., deselect incompatible light sources).
•Exterior Configuration check for NVIS equipment (e.g., ensure exterior lights are NVIS if they were modified by the NVIS STC).
•Adjust lighting as desired.
4.1.2. In-flight.
•Adjust lighting as desired.
•Transition to aided from unaided operations (and vice versa) as necessary.
•Additional equipment procedures, as necessary
4.1.3. Post Flight. Report Discrepancie s (NVG, NVIS lighting and equipment, and windshield) and record discrepancies for maintenance action and follow-up.
4.1.4. Special Procedures. Describe any unique procedures for each phase of flight if required.
5. Weight and Balance. The basic weight and balance should include the installation of NVIS equipment.
Additional Information in RFM(s). It is recommended that a sufficiently detailed system description be provided.
(This ends the section of one template for use as an RFMS.)
AC 29-2C, Chg 2 4/25/06 Page MG 16 - 16