CONTENTS (CONTINUED) Paragraph Page SECTION 8. TAP TESTING
5-105. General5-53
Figure 5-22. Sample of Special Tap Hammer5-53
5-106.5-111. [RESERVED.]5-53
SECTION 9. ACOUSTIC-EMISSION
5-112. General5-53
5-113. Applications5-54
5-114.5-119. [RESERVED.]5-54
SECTION 10. THERMOGRAPHY
5-120. General5-54
5-121.5-126. [RESERVED.]5-54
SECTION 11. HOLOGRAPHY
5-127. General5-54
5-128.5-133. [RESERVED.]5-54
SECTION 12. SHEAROGRAPHY
5-134. General5-55
5-135.5-140. [RESERVED.]5-55
CHAPTER 6. CORROSION, INSPECTION & PROTECTION SECTION 1. GENERAL
6-1.
6-2.
6-3.
6-4.
General6-1
Figure 6-1. Simplified Corrosion Cell Showing Conditions which Must Exist for
Electrochemical Corrosion6-2
Figure 6-2. Elimination of Corrosion by Application of an Organic Film to Metal Surface6-2
Factors Influencing Corrosion6-1
Common Corrosive Agents6-3
Micro-Organisms6-3
6-5.6-10. [RESERVED.]6-4
SECTION 2. TYPES OF CORROSION
6-11. General6-5
Figure 6-3. Corrosion Attack6-5
6-12. General Surface Corrosion6-5
Figure 6-4. General Surface Corrosion6-5
6-13. Pitting Corrosion6-5
Figure 6-5(a). Pitting Corrosion (External View)6-5
Figure 6-5(b). Pitting Corrosion (Magnified Cross Section)6-5
Page xiii
CONTENTS (CONTINUED) Paragraph Page
6-14. Concentration Cell Corrosion6-6
Figure 6-6. Concentration Cell Corrosion6-6
6-15. Active-Passive Cells6-6
Figure 6-7. Active-Passive Cell6-7
6-16. Filiform Corrosion6-7
Figure 6-8. Filiform Corrosion6-7
6-17. Intergranular Corrosion6-7
Figure 6-9. Intergranular Corrosion of 7050-T6 Aluminum Adjacent to Steel Fastener6-8
6-18. Exfoliation Corrosion6-7
Figure 6-10. Exfoliation Corrosion6-8
6-19. Galvanic Corrosion6-8
Figure 6-11. Galvanic Corrosion of Magnesium Adjacent to Steel Fastener6-9
6-20. Stress Corrosion Cracking6-8
Figure 6-12. Stress Corrosion Cracking6-9
6-21. Fatigue Corrosion6-9
6-22. Fretting Corrosion6-10
Figure 6-13. Fretting Corrosion6-10
6-23.6-28. [RESERVED.]6-10
SECTION 3. CORROSION PROTECTION MEASURES FOR BASIC MATERIALS
6-29. General6-11
6-30. Anodizing and Related Processes6-11
6-31. Plating6-11
6-32. Phosphate Rust-Proofing6-11
6-33. Chrome-Pickle Treatment6-11
6-34. Dichromate Treatment6-11
6-35. Stannate Immersion Treatment6-11
6-36. Galvanic Anodizing Treatment6-12
6-37. Cladding6-12
6-38. Metal Spraying6-12
6-39. Shot-Peening6-12
6-40. Organic Coatings6-12
6-41. Dope Proofing6-12
6-42. Tube Interiors6-12
6-43.6-49. [RESERVED.]6-12
SECTION 4. CORROSION PREVENTIVE MAINTENANCE
6-50. Guidelines: All Aircraft6-13
6-51. Guidelines: Aircraft Operating Over Salt Water6-13
6-52.6-62. [RESERVED.]6-14
SECTION 5. VISUAL CORROSION INSPECTION GUIDE FOR AIRCRAFT
6-63. General6-15
6-64. Exhaust Trail Areas6-15
6-65. Battery Compartments and Battery Vent Openings6-15
6-66. Lavatories and Galleys6-15
6-67. Bilge Areas6-15
6-68. Wheel Wells and Landing Gear6-15
Page xiv
CONTENTS (CONTINUED) Paragraph Page
6-69. External Skin Areas6-15
6-70. Water Entrapment Areas6-16
6-71. Engine Frontal Areas6-16
6-72. Electronic Package Compartments6-16
6-73. Flexible Hose Assemblies6-16
6-74. Sandwich Panels6-16
6-75. Control Cables6-16
6-76. Integral Fuel Cells6-16
6-77. Electrical Connectors6-16
6-78.6-88. [RESERVED.]6-16
SECTION 6. CORROSION REMOV AL PROCEDURES
6-89. General6-17
6-90. Safety Precautions6-17
6-91. Corrosion Control Work Procedures6-18
6-92.6-112. [RESERVED.]6-19
SECTION 7. BASIC CORROSION REMOV AL TECHNIQUES
6-113. General6-21
6-114. Preparations for Rework6-21
6-115. Fairing or Blending Reworked Areas6-21
Table 6-1. Abrasives for Corrosion Removal6-22
Figure 6-14. Typical Example of Acceptable Cleanup of Corrosion Pits6-23
Figure 6-15. Blendout of Corrosion as a Single Depression6-24
Figure 6-16. Blendout of Multiple Pits in a Corroded Area6-24
6-116. Corrosion Removal by Blasting6-22
6-117. Cleaners, Polishes, and Brighteners6-22
6-118. Standard Methods6-23
6-119.6-131. [RESERVED.]6-24
SECTION 8. ALUMINUM AND ALUMINUM ALLOYS
6-132. General6-25
6-133. Special Treatment of Anodized Surfaces6-25
6-134. Repair of Aluminum Alloy Sheet Metal6-25
6-135. Corrosion Removal Around Counters unk Fasteners in Aluminum Alloy6-26
6-136. Examples of Removing Corrosion From Aluminum and Aluminum Alloys6-26
6-137.6-147. [RESERVED.]6-28
SECTION 9. MAGNESIUM AND MAGNESIUM ALLOYS
6-148. General6-29
6.149. Treatment of Wrought Magnesium Sheets and Forgings6-29
6.150. Repair of Magnesium Sheet Metal After Extensive Corrosion Removal6-29
6.151. In-Place Treatment of Magnesium Castings6-30
6.152. Example of Removing Corrosion from Magnesium6-30
6-153.6-163. [RESERVED.]6-33
Page xv
CONTENTS (CONTINUED) Paragraph Page SECTION 10. FERROUS METALS
6-164. General6-35
6-165. Special Treatment of High Strength Steel6-35
6-166. Special Treatment of Stainless Steel6-35
6-167. Example of Removing Corrosion from Ferrous Metals6-36
6-168.6-178. [RESERVED.]6-36
SECTION 11. OTHER METALS AND ALLOYS
6-179. Noble Metal Coatings - Cleanup and Restoration6-37
6-180. Copper and Copper Alloys6-37
6-181. Titanium and Titanium Alloys6-37
6-182.6-192. [RESERVED.]6-38
SECTION 12. PLATED PARTS
6-193. Chromium and Nickel Plated Parts6-39
6-194. Cadmium and Zinc Plated Parts6-39
6-195.6-205. [RESERVED.]6-39
SECTION 13. CORROSION PROOFING OF LAND PLANES CONVERTED TO SEA PLANES
6-206. General6-41
6-207. Necessary Minimum Precautions6-41
6-208. Recommended Precautions6-41
6-209.6-219. [RESERVED.]6-42
SECTION 14. HANDLING AND CARE OF AIRCRAFT RECOVERED FROM WATER IMMERSION
6-220. General6-43
6-221. Initial Fresh Water or Detergent Wash6-43
6-222. Reciprocating Engines and Propellers6-43
6-223. Airframe6-43
6-224.6-234. [RESERVED.]6-44
CHAPTER 7. AIRCRAFT HARDWARE, CONTROL CABLES, AND TURNBUCKLES SECTION 1. RIVETS
7-1. General7-1
7-2. Material Applications7-1
7-3.7-13. [RESERVED.]7-2
SECTION 2. SCREWS
7-14. General7-3
7-15. Structural Screws7-3
7-16. Machine Screws7-3
Page xvi
CONTENTS (CONTINUED) Paragraph Page
7-17. Panhead Screws (NAS600 through NAS606, NAS610 through NAS616,
NAS623, and NAS1402 through NAS1406)7-3
7-18. Self-Tapping Screws7-3
7-19. Wood Screws7-4
7-20.7-33. [RESERVED.]7-4
SECTION 3. BOLTS
7-34. General7-5
7-35. Bolts7-5
7-36. Identification7-5
Figure 7-1. Typical Aircraft Bolt Markings7-6
7-37. Grip Length7-5
7-38. Locking or Safetying of Bolts7-6
7-39. Bolt Fit7-6
7-40. Torques7-6
Figure 7-2. Torque Wrench with Various Adapters7-8
Table 7-1. Recommended Torque Values (Inch-Pounds)7-9
7-41. Standard Aircraft Hex Head Bolts (AN3 through AN20)7-7
7-42. Drilled Head Bolts (AN73 through AN81)7-7
7-43. Engine Bolts7-7
7-44. Close-Tolerance Bolts7-9
7-45. Internal Wrenching Bolts (NAS144 thro ugh NAS158 and NAS172 through NAS176)7-10
7-46. Internal Wrenching Bolts (MS20004 through MS20024) and Six Hole,
Drilled Socket Head Bolts (AN148551 through AN149350)7-10
7-47. Twelve Point, External Wrenching Bolts, (NAS624 thro ugh NAS644)7-10
7-48. Close-Tolerance Shear Bolts (NAS434)7-10
7-49. NAS6200 Series Bolts7-10
7-50. Clevis Bolts (AN21 through AN36)7-10
7-51. Eyebolts (AN42 through AN49)7-10
7-52.7-62. [RESERVED.]7-10
SECTION 4. NUTS
7-63. General7-11
7-64. Self-Locking Nuts7-11
Table 7-2. Minimum Prevailing Torque Values for Reused Self-Locking Nuts7-12
7-65. Nut Identification - Finishes7-11
7-66. Castle Nut (AN310)7-12
7-67. Castellated Shear Nut (AN320)7-13
7-68. Plain Nut (AN315 and AN335)7-13
7-69. Light Hex Nuts (AN340 and AN345)7-13
7-70. Checknut (AN 316)7-13
7-71. Wingnuts (AN 350)7-13
7-72. Sheet Spring Nuts (AN365)7-13
7-73.7-84. [RESERVED.]7-13
Page xvii
CONTENTS (CONTINUED) Paragraph Page SECTION 5. WASHERS
7-85. General7-15
7-86. Plain Washers (AN960 and AN970)7-15
7-87. Lockwashers (AN935 and AN936)7-15
7-88. Ball Socket and Seat Washers (AN950 and AN955)7-15
7-89. Taper Pin Washers (AN975)7-15
7-90.7-100. [RESERVED.]7-15
SECTION 6. PINS
7-101 Taper Pins7-17
7-102 Flathead Pins (AN392 thro ugh AN406)7-17
7-103 Cotter Pins (AN380)7-17
7-104 Spring Pins7-17
7-105 Quick-Release Pins7-17
7-106.7-121. [RESERVED.]7-17
SECTION 7. SAFETYING
7-122. General7-19
7-123. Safety Wire7-19
Figure 7-3. Securing Screws, Nuts, Bolts, and Snaprings7-20
Figure 7-3a. Wire Twisting by Hand7-20
7-124. Safety-Wiring Procedures7-20
7-125. Twisting With Special Tools7-21
Figure 7-4. Use of a Typical Wire Twister7-22
7-126. Securing Oil Caps, Drain Cocks, and Valves7-21
Figure 7-4a. Securing Oil Caps, Drain Cocks, and Valves7-22
Figure 7-5. Safety-Wiring Procedures7-23
Figure 7-5a. Safety-Wiring Procedures7-24
Figure 7-5b. Safety-Wiring Procedures7-25
7-127. Securing With Cotter Pins7-26
Figure 7-6. Securing with Cotter Pins7-26
Figure 7-7. Alternate Method for Securing with Cotter Pins7-26
7-128.7-139. [RESERVED.]7-26
SECTION 8. INSPECTION AND REPAIR OF CONTROL CABLES AND TURNBUCKLES
7-140. General7-27
7-141. Cable Definitions7-27
7-142. Flexible Cables7-27
Table 7-3. Flexible Cable Construction and Physical Properties7-28
Figure 7-8. Flexible Cable Cross Section7-29
7-143. Nylon-Coated Cables7-27
7-144. Nonflexible Cables7-28
Table 7-4. Nonflexible Cable Construction and Physical Properties7-29
Figure 7-9. Nonflexible Cable Cross Section7-29
7-145. Cable Specifications7-29
7-146. Cable Proof Loads7-29
7-147. Replacement of Cables7-30
Page xviii
CONTENTS (CONTINUED) Paragraph Page
7-148. Mechanically-Fabricated Cable Assemblies7-30
Table 7-5. Straight-Shank Terminal Dimensions. (Cross Reference AN to MS:
AN-666 to MS2159, AN-667 to MS 20667, AN-668 to MS 20668,
AN-669 to MS 21260.)7-31
Figure 7-10. Insertion of Cable Into Terminal7-31
Figure 7-11. Gauging Terminal Shank After Swaging7-31
Figure 7-12. Typical Cable Splices7-32
Figure 7-13. Typical Terminal Gauge7-32
Figure 7-14. Typical Thimble-Eye Splice7-33
Table 7-6. Copper Oval Sleeve Data7-34
Table 7-7. Copper Stop Sleeve Data7-34
Figure 7-15. Typical Terminal Gauge7-34
7-149. Cable System Inspection7-35
Figure 7-16. Cable Inspection Technique7-35
Figure 7-17. Cable Wear Patterns7-36
Figure 7-18. Worn Cable (Replacement Necessary)7-36
Figure 7-19. Internal Cable Wear7-37
Figure 7-20. Pulley Wear Patterns7-38
7-150. Corrosion and Rust Prevention7-38
Figure 7-21. Corrosion7-39
7-151. Wire Splices7-39
Figure 7-22. Manufacturer’s Wire Splice7-39
7-152. Cable Maintenance7-39
7-153. Cable Tension Adjustment7-39
7-154.7-164. [RESERVED.]7-39
SECTION 9. TURNBUCKLES
7-165. General7-41
7-166. Turnbuckle Installation7-41
Figure 7-23. Turnbuckle Thread Tolerance7-41
7-167. Witness Hole7-41
7-168.7-178. [RESERVED.]7-41
SECTION 10. SAFETY METHODS FOR TURNBUCKLES
7-179. General7-43
7-180. Double-Wrap Method7-43
Figure 7-24. Safetying Turnbuckles7-44
7-181. Single-Wrap Method7-43
7-182. Safety-Wire Secured Turnbuckles7-44
Table 7-8. Turnbuckle Safetying Guide7-45
Figure 7-25. Securing Turnbuckles7-46
7-183. Special Locking Devices7-45
Figure 7-26. Clip-Type Locking Device7-46
7-184. Assembling and Securing Clip-Locking Turnbuckles7-45
Table 7-9. Locking-Clip Application7-47
Figure 7-27. Assembling and Securing Clip-Locking Turnbuckles7-47
7-185.7-195. [RESERVED.]7-47
Page xix
CONTENTS (CONTINUED) Paragraph Page SECTION 11. HARDWARE IDENTIFICATION TABLES
Table 7-10. Table of Rivets7-49
Table 7-11. Table of Screws7-50
Table 7-12. Table of Bolts7-57
Table 7-13. Table of Nuts7-63
Table 7-14. Table of Washers7-69
Table 7-15. Table of Pins7-71
7-196.7-206. [RESERVED.]7-74
CHAPTER 8. ENGINES, FUEL, EXHAUST, AND PROPELLERS SECTION 1. ENGINES
8-1. General8-1
8-2. Special Inspection8-1
8-3. Crankshaft Inspection and Repair Requirements8-3
8-4. Replacement Parts in Certificated Engines8-3
8-5. Oil System Lines Inspection8-4
8-6. Oil Filter Inspection8-4
8-7. Cylinder Hold-Down Nuts and Cap Screws8-4
8-8. Reuse of Safetying Devices8-4
8-9. Self-Locking Nuts for Aircraft Engines and Accessories8-4
8-10. Metallizing8-5
8-11. Plating8-5
Table 8-1. Current Engine and Maximum Permissible Cylinder Barrel Oversize8-6
8-12. Corrosion8-6
8-13. Engine Run-In8-6
8-14. Compression Testing of Aircraft Engine Cylinders8-6
Figure 8-1. Schematic of Differential Pressure Compression Tester8-7
8-15. Spark Plugs8-8
Figure 8-2. Chart of Spark Plug Temperature Ranges8-9
Figure 8-3. Hot and Cold Spark Plugs8-10
Figure 8-4. Spark Plug Reach8-10
Figure 8-5. Method of Checking Spark Plug Gap8-10
8-16. Operational Problems8-11
Figure 8-6. Typical Carbon-Fouled Spark Plug8-12
Figure 8-6a. Typical Lead-Fouled Spark Plug8-12
Figure 8-6b. Typical Oil-Fouled Spark Plug8-13
Figure 8-6c. Typical Spark Plug with Cracked Core Nose8-13
Figure 8-6d. Typical Worn Out Spark Plug8-14
Figure 8-6e. Typical Spark Plug with Bridged Electrodes8-14
Figure 8-7. Spark Plug Well Flashover8-14
8-17. Spark Plug Pre-Reconditioning Inspection8-14
8-18. Ignition Harnesses Inspection8-14
Figure 8-8. Typical Method of Clamping Leads8-15
Page xx
CONTENTS (CONTINUED) Paragraph Page
8-19. Magneto Inspection8-15
Figure 8-9. Normal Contact Point8-16
Figure 8-10. Point with Minor Irregularities8-16
Figure 8-11. Point with Well-Defined Mound8-16
8-20. Magneto-to-Engine Timing8-17
8-21.8-29. [RESERVED.]8-17
SECTION 2. FUEL SYSTEMS
8-30. General8-19
8-31. Fuel Lines and Fittings8-19
Figure 8-12. Location of Clamps at Tube Bends8-20
8-32. Fuel Tanks and Cells8-19
8-33. Fuel Tank Caps, Vents, and Overflow Lines8-20
8-34. Fuel Cross-Feed, Firewall Shutoff, and Tank Selector Valves8-21
8-35. Fuel Pumps8-21
8-36. Fuel Filters, Strainers, and Drains8-21
8-37. Indicator Systems8-22
8-38. Fuel System Precautions8-22
8-39.8-44. [RESERVED.]8-22
SECTION 3. EXHAUST SYSTEMS
8-45. General8-23
8-46. Muffler/Heat Exchanger Failures8-23
Figure 8-13. Typical Muffler Wall Fatigue Failure at Exhaust Outlet.
(A. Complete Muffler Assembly with Heat Shroud Removed; B.
Detail View of Failure.)8-23
Figure 8-14. Typical Muffler Wall Failure. (A. Complete Muffler Assembly with Heat Shroud Removed; B. Detail View of Failure; C. Cross Section of
Failed Muffler.)8-24
Figure 8-15. Typical Muffler Wall Fatigue Failure. (A. Complete Muffler Assembly
with Heat Shroud Partially Removed; B. Detailed View of Failure.)8-25
Figure 8-16. Typical Fatigue Failure of Muffler End Plate at Stack Inlet8-25
8-47. Manifold/Stack Failures8-23
8-48. Internal Muffler Failures8-23
Figure 8-17. Section of a Muffler Showing Typical Internal Baffle Failure8-25
Figure 8-18. Loose Pieces of a Failed Internal Baffle8-25
Figure 8-19. Failed Internal Baffle Partially Obstructing the Muffler Outlet8-27
Figure 8-20. Failed Internal Baffle Completely Obstructing the Muffler Outlet8-27
Figure 8-21a. Example of Exhaust Outlet Guard8-27
Figure 8-21b. Example of Exhaust Outlet Guard Installed8-27
8-49. Inspection8-26
Figure 8-22. Effect of Improperly Positioned Exhaust Pipe/Muffler Clamp8-28
Figure 8-23. Primary Inspection Areas8-28
Page xxi
CONTENTS (CONTINUED) Paragraph Page
8-50. Repairs8-26
8-51. Turbo-Supercharger8-27
8-52. Augmentor Systems8-28
8-53.8-70. [RESERVED.]8-28
SECTION 4. REPAIR OF METAL PROPELLERS
8-71. General8-29
8-72. Steel Blades8-29
8-73. Aluminum Propeller Repairs8-29
Figure 8-24. Method of Repairing Surface Cracks, Nicks, etc., on Aluminum-Alloy Propellers8-30
Figure 8-25. Correct and Incorrect Method of Reworking Leading Edge of
Aluminum-Alloy Propellers8-30
Figure 8-26. Method of Repairing Damaged tip of Aluminum-Alloy Propellers8-31
8-74. Repair Limits8-31
Figure 8-27. Example 1. Determine the Repair Width Limits8-32
Figure 8-28. Example 2. Determine the Repair Thickness Limits8-34
8-75. Steel Hubs and Hub Parts8-33
8-76. Propeller Hub and Flange Repair8-33
Figure 8-29. Repair of Fixed-Pitch Hub and Propeller with Elongated or Damaged Bolt Holes8-35
8-77. Control Systems8-34
8-78. Deicing Systems8-34
8-79. 8-90. [RESERVED.]8-35
SECTION 5. INSPECTION OF PROPELLERS
8-91. General8-37
Table 8-2. Sample Manufacturer’s Propeller Inspection Checklist8-38
8-92. Wood or Composition Propellers and Blades8-37
8-93. Metal Propellers and Blades8-38
8-94. Propeller Hub8-39
8-95. Tachometer Inspection8-40
8-96.8-106. [RESERVED.]8-40
SECTION 6. PROPELLER TRACKING AND VIBRATION
8-107 General8-41
8-108 Propeller Tracking Check8-41
Figure 8-30. Propeller Tracking (Wood Block or Cowling Fixture Shown)8-42
8-109. Vibration8-41
8-110.8-129. [RESERVED.]8-42
Page xxii
CONTENTS (CONTINUED) Paragraph Page CHAPTER 9. AIRCRAFT SYSTEMS AND COMPONENTS SECTION 1. INSPECTION AND MAINTENANCE OF LANDING GEAR
9-1. General9-1
9-2. General Inspection9-1
9-3. Cleaning and Lubricating9-1
9-4. Fixed-Gear Inspection9-1
Table 9-1. Bungee Cord Color Codes9-2
9-5. Inspection of Retractable Landing Gear9-3
9-6. Emergency Systems9-3
9-7. Landing Gear Components9-4
9-8. Floats and Skis9-5
Figure 9-1. A Typical Ski Installation9-6
9-9. Inspection and Repair of Floats and Skis9-7
9-10. Types of Landing Gear Problems9-8
Figure 9-2. Typical Bolt Cracks9-8
Figure 9-3. Typical Cracks Near Bolt Holes9-8
Figure 9-4. Typical Bolt Hole Cracks9-9
Figure 9-5. Typical Rod-End Cracks9-9
Figure 9-6. Typical Torque Tube Bolt Hole Elongation9-9
9-11. Special Inspections9-9
9-12. Retraction Tests9-9
9-13. Tire and Tube Maintenance9-9
9-14. Tire Inspection and Repair9-10
Figure 9-7. Examples of Tread Wear Indicating Over-Inflation and Under-Inflation9-11
9-15. Inflation of Tires9-11
9-16. Personal Safety9-11
9-17. Disassemble the Wheel9-11
9-18. Reassembling the Wheel9-12
9-19. Slippage9-12
9-20. Wheel Inspection9-12
9-21. Wheel Installation9-12a
9-22.9-24. [RESERVED.]9-12
SECTION 2. HYDRAULIC SYSTEMS
9-25. General9-13
9-26. Purposes of Hydraulic Systems9-13
9-27. Types of Hydraulic Fluid9-13
9-28. Handling Hydraulic Fluids9-14
9-29. Hydraulic System Maintenance Practices9-15
9-30. Hydraulic Lines and Fittings9-18
Table 9-2. Tube Data9-19
Figure 9-8. Hose Assembly Instructions (Can Be Used for Low Pressure Hydraulic Fluid,
and Oil Line Applications)9-21
Page xxiii
CONTENTS (CONTINUED) Paragraph Page
Table 9-3. Aircraft Hose Specifications9-22
Figure 9-9. Proper Hose Installations9-23
Figure 9-10. Minimum Bend Radii9-24
Table 9-4. Ball Diameters for Testing Hose Restrictions or Kinking9-25
Figure 9-11. Suggested Handling of Preformed Hose9-25
9-31.9-36. [RESERVED.]9-26
SECTION 3. EMERGENCY EQUIPMENT
9-37. Life Rafts9-27
9-38. Life Raft Inspections9-27
Figure 9-12. Inflation Valve9-29
9-39. Survival Kit Inspection9-28
9-40. Special Inspections9-31
9-41. Inspection Record9-32
9-42. Raft Repairs9-32
Figure 9-13. Repair Dimensions9-33
9-43. Life Preservers9-34
9-44. Life Preserver Inspection9-35
9-45. Repair of Life Preservers9-36
9-46. Miscellaneous Equipment9-36
9-47. Oxygen Systems9-37
9-48. Inspection9-37
9-49. Maintenance9-38
Figure 9-14. Oxygen Cylinder Damage9-39
Figure 9-15. Cylinder Brackets and Clamps9-39
9-50. Functional Testing After Repair9-41
9-51. Service Requirements --Oxygen Cylinders9-41
Table 9-5. Table of Filling Pressures9-43
9-52.9-59. [RESERVED.]9-43
SECTION 4. CABIN INTERIOR
9-60. General9-45
9-61. Car-3 Aircraft Interior9-45
9-62. Part 23 Aircraft Interior9-45
9-63. Source of Information9-46
9-64. Upholstery and/or Belts9-46
9-65.9-70. [RESERVED.]9-46
CHAPTER 10. WEIGHT AND BALANCE SECTION 1. TERMINOLOGY
10-1. General10-1
10-2. Terminology10-1
Figure 10-1. Typical Datum Locations10-2
Figure 10-2. Illustration of Arm (or Moment Arm)10-3
Figure 10-3. Example of Moment Computation10-4
Figure 10-4. Empty Weight Center of Gravity Formulas10-5
Figure 10-5. Empty Weight and Empty Center of Gravity - Tail-Wheel Type Aircraft10-6
Page xxiv