TABLE 4-8. Aircraft rivet identification.
Material 1100 2117T 2017T 2017T-HD 2024T 5056T 7075-T73 Head Marking Plain Dimpled Raised Dot Raised Dot Raised Double Dash Raised Cross Three Raised Dashes AN Material Code
A AD D D DD B AN425 78�� �� Counter- Sunk Head
X X X X X X AN426 100�� �� Counter- Sunk Head MS20426
X X X X X X X AN427 100�� �� Counter- Sunk Head MS20427 AN430 Round Head MS20470
X X X X X X X AN435 Round Head MS20613 MS20615 AN 441 Flat Head AN 442 Flat Head MS20470
X X X X X X X AN 455 Brazier Head MS20470
X X X X X X X AN 456 Brazier Head MS20470
X X X X X X X AN 470 Universal Head MS20470
X X X X X X X Heat Treat Before Using No No Yes No Yes No No Shear Strength psi 10000 30000 34000 38000 41000 27000 Bearing Strength psi 25000 100000 113000 126000 136000 90000 Par 4-57 Page 4-17
TABLE 4-8. Aircraft rivet identification. (continued) Material Carbon Steel Corrosion- Resistant Steel Copper Monel Monel Nickel- Copper Alloy Brass Titanium Head Marking Recessed Triangle Recessed Dash Plain Plain Recessed Double Dots Plain Recessed Large and Small Dot AN Material Code
F C M C AN425 78�� �� Counter- Sunk Head AN426 100�� �� Counter- Sunk Head MS20426 MS 20426 AN427 100�� �� Counter- Sunk Head MS20427
X X X X AN430 Round Head MS20470 AN435 Round Head MS20613 MS20615 X MS20613 X MS20613 X X MS20615 X MS20615 AN 441 Flat Head
X X X X AN 442 Flat Head MS20470 AN 455 Brazier Head MS20470 AN 456 Brazier Head MS20470 AN 470 Universal Head MS20470 Heat Treat Before Using No No No No No No No Shear Strength psi 35000 65000 23000 49000 49000 95000 Bearing Strength psi 90000 90000 Page 4-18 Par 4-57
c. Rivet edge distance is defined as the distance from the center of the rivet hole to the nearest edge of the sheet. Rivet spacing is the distance from the center of the rivet hole to the center of the adjacent rivet hole. Unless structural deficiencies are suspected, the rivet spacing and edge distance should duplicate those of the original aircraft structure. If structural deficiencies are suspected, the fol lowing may be used in determining minimum edge distance and rivet spacing.
(1) For single row rivets, the edge dis tance should not be less than 2 times the di ameter of the rivet and spacing should not be less than 3 times the diameter of the rivet.
(2) For double row rivets, the edge dis tance and spacing should not be less than the minimums shown in figure 4-5.
(3) For triple or multiple row rivets, the edge distance and spacing should not be less than the minimums shown in figure 4-5.
d. The 2117 rivets may be driven in the condition received, but 2017 rivets above 3/16 inch in diameter and all 2024 rivets are to be kept packed in dry ice or refrigerated in the “quenched” condition until driven, or be reheat treated just prior to driving, as they would oth erwise be too hard for satisfactory riveting.
Dimensions for formed rivet heads are shown in figure 4-6(a), together with commonly found rivet imperfections.
e. When solid shank rivets are impracti cal to use, then special fasteners are used.
Special fastening systems used for aircraft construction and repair are divided into two types, special and blind fasteners. Special fasteners are sometimes designed for a specific purpose in an aircraft structure. The name “special fasteners” refers to its job requirement and the tooling needed for installation. Use of special fasteners may require an FAA field ap proval.
f. Blind rivets are used under certain con ditions when there is access to only one side of the structure. Typically, the locking charac teristics of a blind rivet are not as good as a driven rivet. Therefore, blind rivets are usually not used when driven rivets can be installed.
Blind rivets shall not be used:
(1) in fluid-tight areas;
(2) on aircraft in air intake areas where rivet parts may be ingested by the engine, on aircraft control surfaces, hinges, hinge brack ets, flight control actuating systems, wing at tachment fittings, landing gear fittings, on floats or amphibian hulls below the water level, or other heavily-stressed locations on the aircraft;
CAUTION: For metal repairs to the air frame, the use of blind rivets must be spe cifically authorized by the airframe manu facturer or approved by a representative of the FAA.
(3) Self plugging friction-lock cherry rivets. This patented rivet may be installed when there is access to only one side of the structure. The blind head is formed by pulling the tapered stem into the hollow shank. This swells the shank and clamps the skins tightly together. When the shank is fully upset, the stem pulls in two. The stem does not fracture flush with the rivet head and must be trimmed and filed flush for the installation to be com plete. Because of the friction-locking stem, these rivets are very sensitive to vibrations.
Inspection is visual, with a loose rivet standing out in the standard “smoking rivet” pattern.
Removal consists of punching out the friction- Par 4-57 Page 4-19 (and 4-19a)
locked stem and then treating it like any other rivet. (See figure 4-7.)
(4) Mechanical-lock rivets have a de vice on the puller or rivet head which locks the center stem into place when installed. Many friction-lock rivet center stems fall out due to vibrations; this in turn, greatly reduces its shear strength. The mechanical-lock rivet was developed to prevent that problem. Various manufacturers make mechanical-lock fastern ers such as: Bulbed Cherrylock, CherryMax, Olympic-Loks, and Huck-Loks.
Par 4-57 Page 4-19b
STRENGTH THROUGH THIS SECTION IS 75% OF SHEET WITHOUT HOLES.
D = DIAMETER OF 4D RIVET (PREFER- ABLY ABOUT 3x
THICKNESS OF
THICKER SHEET) 20→ ÷4D= *20 (A) DOUBLE ROW
CAN DO TO SA NOTES WITHOUT HOLES.
20-9 * 20 (B) TRIPLE OR MULTIPLE ROWS FIGURE 4-5. Rivet hole spacing and edge distance for single-lap sheet splices.
Page 4-20 Par 4-57
(a) DIMENSIONS FOR FORMED RIVET HEADS, _65D (ID MIN.) + 1¿0→ (MIN.) (=D MIN.)
(b) RIVETING TOOLS
CORRECT
INCORRECT SHAPE FOR
RIVET SNAF OR SET.
BUCKING BAR OR DOLLY.
(C) RIVET IMPERFECTIONS.
RIVET DRIVEN AT SLANT, RIVET DRIVEN RIVET FLAT ON ONE
CORRECTLY, DOLLY SIDE OR DOLLY HELD HEAD AT SLANT. FLAT.
BODY OF RIVET TOO SHORT. CLOSING HEAD RIVET NOT PULLED TIGHT, CLINCHES BULGED ON ACCOUNT RIVET TIGHT, PLATES SHAPED TOO MUCH BETWEEN PLATES, OF POOR FIT.
WITH SNAP DIE. CLOSING HEAD TOO FLAT.
RIVETED TOO MUCH. RIVET BODY CLINCHED TOO MUCH, HEAD CRACKED.
PLATES CLINCHED AT RIVET MATERIAL TOO AND DRIVEN APART. HARD WHEN RIVETING TOOL FORMED.
DAMAGED PLATE FIGURE 4-6. Riveting practice and rivet imperfections.
Par 4-57 Page 4-21
FIGURE 4-7. Self plugging friction-lock Cherry rivets.
(5) Bulbed Cherrylock Rivets. One of the earlier types of mechanical-lock rivets de veloped were Bulbed Cherrylock blind rivets.
These blind rivets have as their main advan tage the ability to replace a solid shank rivet size for size. (See figure 4-8.)
(a) A Bulbed Cherrylock consists of three parts; a rivet shell, a puller, and a lockring. The puller or stem has five features which are activated during installation; a header, shank expanding section, lockring in dent, weak or stem fracture point, and a ser rated pulling stem. Carried on the pulling stem, near the manufactured head, is the stem lockring. When the rivet is pulled the action of the moving stem clamps together the sheets of metal and swells the shank to fill the drilled hole. When the stem reaches its preset limit of travel, the upper stem breaks away (just above the lockring) as the lockring snaps into the re cess on the locking stem. The rough end of the retained stem in the center on the manufac tured head must never be filed smooth, be cause it will weaken the strength of the lockring and the center stem could fall out. (See figure 4-8.)
(b) The Bulbed Cherrylock rivets are available in two head styles: universal and 100° countersunk. Their lengths are measured in increments of 1/16 inch. It is important to select a rivet with a length related to the grip length of the metal being joined.
(c) The Bulbed Cherrylock rivet can be installed using a G35 cherry rivet hand puller or a pneumatic Bulbed Cherrylock pulling tool.
(6) The CherryMax (see figure 4-9) rivet uses one tool to install three standard rivet diameters and their oversize counterparts.
This makes the use of CherryMax rivets very popular with many small general aviation re pair shops. CherryMax rivets are available in four nominal diameters 1/8, 5/32, 3/16, and 1/4 inch and three oversized diameters. Cher ryMax rivets are manufactured with two head styles, universal and countersunk. The Cher ryMax rivets consists of five parts; bulbed blind header, hollow rivet shell, locking (foil) collar, driving anvil, and pulling stem. The blind bulbed header takes up the extended shank and forms the bucktail on a CherryMax rivet stem. Rivet sleeves are made from 5056 aluminum, monel, and INCO 600. The stems are made from alloy steel, CRES, and INCO X-750 stem. CherryMax rivets have an ultimate shear strength ranging from 50 KSI to 75 KSI.
(7) An Olympic-Lok (see figure 4-10) rivet is a light three-piece mechanically locked, spindle-type blind rivet. It carries its stem lock integral to the manufactured head. While in stalling, the lockring is pressed into a groove on the pulling stem just as the rivet completes drawing the metal together. After installation is completed, never file the stem of an Olympic-Lok rivet, because it will weaken the lockring attachment. The Olympic-Lok fastener is available in three head styles:
Page 4-22 Par 4-57
- STEM
STEM IS PULLED
COLLAR LOCKING BEFORE PULLING INTO RIVET SLEEVE AND STARTS TO FORM BULB BLIND HEAD BEGINS RIVET HEAD SHEET GAP > CLAMP-UP AND
HOLE FILL
Y ACTION BEGIN SHEAR RING
FORMATION OF BLIND
CLAMP-UP COMPLETED HEAD AND HOLE FILLING
AS STEM CONTINUES TO ARE COMPLETED
BULB OUT BLIND HEAD
SHEAR RING NOW SHEARS
FROM STEM CONE TO ALLOW
STEM TO PULL FURTHER INTO
RIVET HEAD RIVET
FIRMLY SEATED
BLIND SIDE BULB HEAD
- IS FORMED BELOW SHEAR RING GUARANTEES
MINIMUM GRIP BLIND SIDE BULBED HEAD (IN MINIMUM GRIP SHEAR
RING MAY NOT SHEAR)
SHEAR RING HAS MOVED
DOWN STEM CONE UNTIL
PULLING HEAD AUTOMATICALLY STOPS COMPLETELY INSTALLED
STEM BREAK NOTCH BULBED CHERRYLOCK
FLUSH WITH TOP OF
RIVET HEAD
PULLING HEAD HAS _OCKING COLLAR IS NOV INSERTED LOCKING
EADY TO BE INSERTED COLLAR AND STEM
HAS FRACTURED FLUSH
WITH RIVET HEAD (MAXIMUM GRIP
BLIND SIDE ILLUSTRATED)
BULBED HEAD FIGURE 4-8. Mechanical-lock (Bulbed Cherrylock) Cherry rivet.
Par 4-57 Page 4-23
FIGURE 4-9. CherryMax rivet.
universal protruding, 100-degree flush coun tersink, and 100-degree flush shear; and three diameters 1/8, 5/32, and 3/16 inch. The three diameters are available in eight different alloy combinations of 2017-T4, A-286, 5056, and monel. Olympic-Lok lock spindles are made from the same material as the sleeves.
(8) Huck rivets (see figure 4-11) are available in two head styles, protruding and flush. They are available in four diameters 1/8, 5/32, 3/16, and 1/4 inch. Their diameters are measured in increments of 1/32 inch and lengths are measured in 1/16 inch increments.
They are manufactured in three different com binations of alloys: 5056 aluminum sleeve with 2024 aluminum alloy pin, A-286 corro sion-resistant steel sleeve with an A-286 pin, and a monel 400 sleeve with an A-286 pin.
The Huck fastener has the ability to tightly draw-up two or more sheets of metal together while being installed. After the take-up of the Huck fastener is completed, the lockring is squeezed into a groove on the pulling stem.
The anvil or footer (of the installation tool) packs the ring into the groove of the pulling stem by bearing against the lockring.
(9) Common pull-type Pop rivets, pro duced for nonaircraft related applications, are not approved for use on certificated aircraft structures or components.
g. Design a new or revised rivet pattern for strength required in accordance with one of the following:
(1) The aircraft manufacturer’s mainte nance manuals.
(2) The techniques found in structural text books and using the mechanical properties found in MIL-HDBK-5.
(3) The specific instructions in para graphs 4-58g through 4-58n. When following the instruction in paragraphs 4-58g through 4-58n, the general rule for the diameter of the rivets used to join aluminum sheets is to use a diameter approximately three times the thick ness of the thicker sheet. Do not use rivets where they would be placed in tension, tending to pull the heads off; and backup a lap joint of thin sheets with a stiffener section.
Page 4-24 Par 4-57
SLEEVE REDUCED INTERNAL DIAMETER TO DOUBLE
PRECISELY ALIGN THE LOCKING GROOVE TAPER DESIGN
FULLY SERRATED STEM CONTINUOUS INTEGRAL
FOR INCREMENTAL PULL-UP LOCKING COLLAR RV 1201 SERIES
COUNTERSUNK
HEAD STYLE 1/16 INCH GRIP VARIATION CAPABILITY
DESIGNED INTO FASTENER
LARGER SECOND SHANK RV 1200 SERIES FLUSH BREAKING STEM DIAMETER FOR EXTRA
PROTRUDING SLEEVE EXPANSION AND
HEAD STYLE GREAT BLIND-SIDE
BEARING AREA
GREATER LOCKING COLLAR VOLUME PROTRUDING HEAD
DRIVEN INTO LOCKING GROOVE UNDERCUT ELIMINATES
DEBURRING Olympic-Lok blind rivet is Tool jaws grip the stem and inserted into a prepared pull it into the sleeve, closing hole. Note the clearance the sheet gap, expanding the between the rivet and the sleeve to fill the hole, and sides of the hole and the forming a consistently larger gap between the sheets. blind side bearing area.
FIGURE 4-10. Olympic-Lok rivet.
4-58. REPAIR METHODS AND PRE-
CAUTIONS FOR ALUMINUM STRUC- TURE. Carefully examine all adjacent rivets outside of the repair area to ascertain that they have not been harmed by operations in adjacent areas. Drill rivet holes round, straight, and free from cracks. Deburr the hole with an oversize drill or deburring tool. The rivet-set used in driving the rivets must be cupped slightly flatter than the rivet head. (See figure 4-6.) Rivets are to be driven straight and tight, but not overdriven or driven while too hard, since the finished rivet must be free from cracks. Information on special methods of riveting, such as flush riveting, usually may be obtained from manufacturer's service manuals.
When the stem travel is Continued pulling breaks stopped by the sleeve's inter- the stem flush to the fastennal step, the integral locking er head. Flushness is collar shears free and is assured by the positioning forced into the stem locking of the break-groove when groove. This forms a stem travel is stopped by permanent mechanical lock. the sleeve's internal step.
a. Splicing of Tubes. Round or streamline aluminum alloy tubular members may be repaired by splicing. (See figure 4-12.)
Splices in struts that overlap fittings are not acceptable. When solid rivets go completely through hollow tubes, their diameter must be at least one-eighth of the outside diameter of the outer tube. Rivets which are loaded in shear should be hammered only enough to form a small head and no attempt made to form the standard roundhead. The amount of hammering required to form the standard roundhead often causes the rivet to buckle inside the tube. (Correct and incorrect examples of this type of rivet application are incorporated in figure 4-12.)
Par 4-57 Page 4-25
FIGURE 4-11. Huck rivet.
b. Repairs to Aluminum Alloy Mem bers. Make repairs to aluminum alloy mem bers with the same material or with suitable material of higher strength. The 7075 alloy has greater tensile strength than other com monly used aluminum alloys such as 2014 and 2024, but is subject to somewhat greater notch sensitivity. In order to take advantage of its strength characteristics, pay particular attention to design of parts to avoid notches, small radii, and large or rapid changes in cross-sectional areas. In fabrication, exercise caution to avoid processing and handling defects, such as ma chine marks, nicks, dents, burrs, scratches, and forming cracks. Cold straightening or forming of 7075-T6 can cause cracking; therefore, it may be advisable to limit this processing to minor cold straightening.
c. Wing and Tail Surface Ribs. D a m aged aluminum alloy ribs either of the stamped sheet-metal type or the built-up type employ ing special sections, square or round tubing, may be repaired by the addition of suitable re inforcement. (Acceptable methods of repair are shown in figures 4-13 and 4-14.) These examples deal with types of ribs commonly found in small and medium size aircraft. Re pair schemes developed by the aircraft manu facturer are acceptable, but any other methods of reinforcement are major repairs and require approved data.
d. Trailing and Leading Edges and Tip Strips. Repairs to wing, control surface trail ing edges, leading edges, and tip strips should be made by properly executed and reinforced splices. Acceptable methods of trailing edge repairs are shown in figure 4-15.
e. Repair of Damaged Skin. I n c a s e s where metal skin is damaged extensively, re pair by replacing an entire sheet panel from one structural member to the next. The repair seams are to lie along stiffening members, bulkheads, etc.; and each seam must be made exactly the same in regard to rivet size, splic ing, and rivet pattern as the manufactured seams at the edges of the original sheet. If the two manufactured seams are different, the stronger one will be copied. (See figure 4-16 for typical acceptable methods of repairs.)
f. Patching of Small Holes. Small holes in skin panels which do not involve damage to the stiffening members may be patched by covering the hole with a patch plate in the manner shown in figure 4-16. Flush patches also may be installed in stressed-skin type con struction. An acceptable and easy flush patch may be made by trimming out the damaged area and then installing a conventional patch on the underneath side or back of the sheet being repaired. A plug patch plate of the same size and skin thickness as the opening may then be inserted and riveted to the patch plate.
Other types of flush patches similar to those Page 4-26 Par 4-58
used for patching plywood may be used. The rivet pattern used, however, must follow stan dard practice to maintain satisfactory strength in the sheet.
g. Splicing of Sheets. The method of copying the seams at the edges of a sheet may not always be satisfactory. For example, when the sheet has cutouts, or doubler plates at an edge seam, or when other members transmit loads into the sheet, the splice must be de signed as illustrated in the following examples.
(1) Material: Clad 2024 sheet,
0.032 inch thickness. Width of sheet (i.e., length at splice) = “W” = 10 inches.
(2) Determine rivet size and pattern for a single-lap joint similar to figure 4-5.
(a) Use rivet diameter of approxi mately three times the sheet thickness, 3 x 0.032 = 0.096-inch. Use 1/8-inch 2117-T4 (AD) rivets (5/32-inch 2117-T4 (AD) would be satisfactory).
(b) Use the number of rivets re quired per inch of width “W” from table 4-10.
(Number per inch 4.9 x .75 = 3.7 or the total number of rivets required = 10 x 3.7 or 37 riv ets.) See notes in table.
(c) Lay out rivet pattern with spacing not less than shown in figure 4-5. Referring to figure 4-5(A), it seems that a double row pat tern with the minimum spacing will give a to tal of 40 rivets. However, as only 37 rivets are required, two rows of 19 rivets each equally spaced over the10 inches will result in a satis factory splice.
h. Straightening of Stringers or Inter mediate Frames. Members which are slightly bent may be straightened cold and examined with a magnifying glass for cracks or tears to the material. Reinforce the straightened part to its original shape, depending upon the condi tion of the material and the magnitude of any remaining kinks or buckles. If any strain cracks are apparent, make complete reinforce ment in sound metal beyond the damaged por tion.
i. Local Heating. Do not apply local heating to facilitate bending, swaging, flatten ing, or expanding operations of heat-treated aluminum alloy members, as it is difficult to control the temperatures closely enough to prevent possible damage to the metal, and it may impair its corrosion resistance.
j. Splicing of Stringers and Flanges. I t is recommended that all splices be made in ac cordance with the manufacturer’s recommen dations. If the manufacturer’s recommenda tions are not available, the typical splices for various shapes of sections are shown in figures 4-17 through 4-19. Design splices to carry both tension and compression, and use the splice shown in figure 4-18 as an example il lustrating the following principles.
(1) To avoid eccentric loading and con sequent buckling in compression, place splic ing or reinforcing parts as symmetrically as possible about the centerline of the member, and attach to as many elements as necessary to prevent bending in any direction.
(2) To avoid reducing the strength in tension of the original bulb angle, the rivet holes at the ends of the splice are made small (no larger than the original skin attaching riv ets), and the second row of holes (those through the bulbed leg) are staggered back from the ends. In general, arrange the rivets in the splice so that the design tensile load for the member and splice plate can be carried into the splice without failing the member at the out ermost rivet holes.
Par 4-58 Page 4-27