AC 43.13-1B

Change 1Historical

Advisory circular · Acceptable Methods, Techniques, and Practices—Aircraft Inspection and Repair

A newer version is currentThis is a historical version. AC 43.13-1B CHG 1 Ed Update is the version in force, approved September 27, 2001.
Approved
September 9, 1998
Last reviewed
June 11, 2024
Cancels
AC43.13-1B
Family
AC 43.13-1 · 7 versions
Revision
B, change 1
14 CFR parts
43, 65, 145, 21, 105, 23, 91, 121, 25
Cited by
95 ADs

Guidance, not mandatory unless a rule or AD requires it. DRS record last changed November 21, 2025.

Show pages 152–163
Page 164OCROpen in PDF

- STEM

STEM IS PULLED

COLLAR LOCKING BEFORE PULLING INTO RIVET SLEEVE AND STARTS TO FORM BULB BLIND HEAD BEGINS RIVET HEAD SHEET GAP > CLAMP-UP AND

HOLE FILL

Y ACTION BEGIN SHEAR RING

FORMATION OF BLIND

CLAMP-UP COMPLETED HEAD AND HOLE FILLING

AS STEM CONTINUES TO ARE COMPLETED

BULB OUT BLIND HEAD

SHEAR RING NOW SHEARS

FROM STEM CONE TO ALLOW

STEM TO PULL FURTHER INTO

RIVET HEAD RIVET

FIRMLY SEATED

BLIND SIDE BULB HEAD

- IS FORMED BELOW SHEAR RING GUARANTEES

MINIMUM GRIP BLIND SIDE BULBED HEAD (IN MINIMUM GRIP SHEAR

RING MAY NOT SHEAR)

SHEAR RING HAS MOVED

DOWN STEM CONE UNTIL

PULLING HEAD AUTOMATICALLY STOPS COMPLETELY INSTALLED

STEM BREAK NOTCH BULBED CHERRYLOCK

FLUSH WITH TOP OF

RIVET HEAD

PULLING HEAD HAS _OCKING COLLAR IS NOV INSERTED LOCKING

EADY TO BE INSERTED COLLAR AND STEM

HAS FRACTURED FLUSH

WITH RIVET HEAD (MAXIMUM GRIP

BLIND SIDE ILLUSTRATED)

BULBED HEAD FIGURE 4-8. Mechanical-lock (Bulbed Cherrylock) Cherry rivet.

Par 4-57 Page 4-23

Page 165Open in PDF

FIGURE 4-9. CherryMax rivet.

universal protruding, 100-degree flush coun­ tersink, and 100-degree flush shear; and three diameters 1/8, 5/32, and 3/16 inch. The three diameters are available in eight different alloy combinations of 2017-T4, A-286, 5056, and monel. Olympic-Lok lock spindles are made from the same material as the sleeves.

(8) Huck rivets (see figure 4-11) are available in two head styles, protruding and flush. They are available in four diameters 1/8, 5/32, 3/16, and 1/4 inch. Their diameters are measured in increments of 1/32 inch and lengths are measured in 1/16 inch increments.

They are manufactured in three different com­ binations of alloys: 5056 aluminum sleeve with 2024 aluminum alloy pin, A-286 corro­ sion-resistant steel sleeve with an A-286 pin, and a monel 400 sleeve with an A-286 pin.

The Huck fastener has the ability to tightly draw-up two or more sheets of metal together while being installed. After the take-up of the Huck fastener is completed, the lockring is squeezed into a groove on the pulling stem.

The anvil or footer (of the installation tool) packs the ring into the groove of the pulling stem by bearing against the lockring.

(9) Common pull-type Pop rivets, pro­ duced for nonaircraft related applications, are not approved for use on certificated aircraft structures or components.

g. Design a new or revised rivet pattern for strength required in accordance with one of the following:

(1) The aircraft manufacturer’s mainte­ nance manuals.

(2) The techniques found in structural text books and using the mechanical properties found in MIL-HDBK-5.

(3) The specific instructions in para­ graphs 4-58g through 4-58n. When following the instruction in paragraphs 4-58g through 4-58n, the general rule for the diameter of the rivets used to join aluminum sheets is to use a diameter approximately three times the thick­ ness of the thicker sheet. Do not use rivets where they would be placed in tension, tending to pull the heads off; and backup a lap joint of thin sheets with a stiffener section.

Page 4-24 Par 4-57

Page 166OCROpen in PDF

SLEEVE REDUCED INTERNAL DIAMETER TO DOUBLE

PRECISELY ALIGN THE LOCKING GROOVE TAPER DESIGN

FULLY SERRATED STEM CONTINUOUS INTEGRAL

FOR INCREMENTAL PULL-UP LOCKING COLLAR RV 1201 SERIES

COUNTERSUNK

HEAD STYLE 1/16 INCH GRIP VARIATION CAPABILITY

DESIGNED INTO FASTENER

LARGER SECOND SHANK RV 1200 SERIES FLUSH BREAKING STEM DIAMETER FOR EXTRA

PROTRUDING SLEEVE EXPANSION AND

HEAD STYLE GREAT BLIND-SIDE

BEARING AREA

GREATER LOCKING COLLAR VOLUME PROTRUDING HEAD

DRIVEN INTO LOCKING GROOVE UNDERCUT ELIMINATES

DEBURRING Olympic-Lok blind rivet is Tool jaws grip the stem and inserted into a prepared pull it into the sleeve, closing hole. Note the clearance the sheet gap, expanding the between the rivet and the sleeve to fill the hole, and sides of the hole and the forming a consistently larger gap between the sheets. blind side bearing area.

FIGURE 4-10. Olympic-Lok rivet.

4-58. REPAIR METHODS AND PRE-

CAUTIONS FOR ALUMINUM STRUC- TURE. Carefully examine all adjacent rivets outside of the repair area to ascertain that they have not been harmed by operations in adjacent areas. Drill rivet holes round, straight, and free from cracks. Deburr the hole with an oversize drill or deburring tool. The rivet-set used in driving the rivets must be cupped slightly flatter than the rivet head. (See figure 4-6.) Rivets are to be driven straight and tight, but not overdriven or driven while too hard, since the finished rivet must be free from cracks. Information on special methods of riveting, such as flush riveting, usually may be obtained from manufacturer's service manuals.

When the stem travel is Continued pulling breaks stopped by the sleeve's inter- the stem flush to the fastennal step, the integral locking er head. Flushness is collar shears free and is assured by the positioning forced into the stem locking of the break-groove when groove. This forms a stem travel is stopped by permanent mechanical lock. the sleeve's internal step.

a. Splicing of Tubes. Round or streamline aluminum alloy tubular members may be repaired by splicing. (See figure 4-12.)

Splices in struts that overlap fittings are not acceptable. When solid rivets go completely through hollow tubes, their diameter must be at least one-eighth of the outside diameter of the outer tube. Rivets which are loaded in shear should be hammered only enough to form a small head and no attempt made to form the standard roundhead. The amount of hammering required to form the standard roundhead often causes the rivet to buckle inside the tube. (Correct and incorrect examples of this type of rivet application are incorporated in figure 4-12.)

Par 4-57 Page 4-25

Page 167Open in PDF

FIGURE 4-11. Huck rivet.

b. Repairs to Aluminum Alloy Mem­ bers. Make repairs to aluminum alloy mem­ bers with the same material or with suitable material of higher strength. The 7075 alloy has greater tensile strength than other com­ monly used aluminum alloys such as 2014 and 2024, but is subject to somewhat greater notch sensitivity. In order to take advantage of its strength characteristics, pay particular attention to design of parts to avoid notches, small radii, and large or rapid changes in cross-sectional areas. In fabrication, exercise caution to avoid processing and handling defects, such as ma­ chine marks, nicks, dents, burrs, scratches, and forming cracks. Cold straightening or forming of 7075-T6 can cause cracking; therefore, it may be advisable to limit this processing to minor cold straightening.

c. Wing and Tail Surface Ribs. D a m ­ aged aluminum alloy ribs either of the stamped sheet-metal type or the built-up type employ­ ing special sections, square or round tubing, may be repaired by the addition of suitable re­ inforcement. (Acceptable methods of repair are shown in figures 4-13 and 4-14.) These examples deal with types of ribs commonly found in small and medium size aircraft. Re­ pair schemes developed by the aircraft manu­ facturer are acceptable, but any other methods of reinforcement are major repairs and require approved data.

d. Trailing and Leading Edges and Tip Strips. Repairs to wing, control surface trail­ ing edges, leading edges, and tip strips should be made by properly executed and reinforced splices. Acceptable methods of trailing edge repairs are shown in figure 4-15.

e. Repair of Damaged Skin. I n c a s e s where metal skin is damaged extensively, re­ pair by replacing an entire sheet panel from one structural member to the next. The repair seams are to lie along stiffening members, bulkheads, etc.; and each seam must be made exactly the same in regard to rivet size, splic­ ing, and rivet pattern as the manufactured seams at the edges of the original sheet. If the two manufactured seams are different, the stronger one will be copied. (See figure 4-16 for typical acceptable methods of repairs.)

f. Patching of Small Holes. Small holes in skin panels which do not involve damage to the stiffening members may be patched by covering the hole with a patch plate in the manner shown in figure 4-16. Flush patches also may be installed in stressed-skin type con­ struction. An acceptable and easy flush patch may be made by trimming out the damaged area and then installing a conventional patch on the underneath side or back of the sheet being repaired. A plug patch plate of the same size and skin thickness as the opening may then be inserted and riveted to the patch plate.

Other types of flush patches similar to those Page 4-26 Par 4-58

Page 168Open in PDF

used for patching plywood may be used. The rivet pattern used, however, must follow stan­ dard practice to maintain satisfactory strength in the sheet.

g. Splicing of Sheets. The method of copying the seams at the edges of a sheet may not always be satisfactory. For example, when the sheet has cutouts, or doubler plates at an edge seam, or when other members transmit loads into the sheet, the splice must be de­ signed as illustrated in the following examples.

(1) Material: Clad 2024 sheet,

0.032 inch thickness. Width of sheet (i.e., length at splice) = “W” = 10 inches.

(2) Determine rivet size and pattern for a single-lap joint similar to figure 4-5.

(a) Use rivet diameter of approxi­ mately three times the sheet thickness, 3 x 0.032 = 0.096-inch. Use 1/8-inch 2117-T4 (AD) rivets (5/32-inch 2117-T4 (AD) would be satisfactory).

(b) Use the number of rivets re­ quired per inch of width “W” from table 4-10.

(Number per inch 4.9 x .75 = 3.7 or the total number of rivets required = 10 x 3.7 or 37 riv­ ets.) See notes in table.

(c) Lay out rivet pattern with spacing not less than shown in figure 4-5. Referring to figure 4-5(A), it seems that a double row pat­ tern with the minimum spacing will give a to­ tal of 40 rivets. However, as only 37 rivets are required, two rows of 19 rivets each equally spaced over the10 inches will result in a satis­ factory splice.

h. Straightening of Stringers or Inter­ mediate Frames. Members which are slightly bent may be straightened cold and examined with a magnifying glass for cracks or tears to the material. Reinforce the straightened part to its original shape, depending upon the condi­ tion of the material and the magnitude of any remaining kinks or buckles. If any strain cracks are apparent, make complete reinforce­ ment in sound metal beyond the damaged por­ tion.

i. Local Heating. Do not apply local heating to facilitate bending, swaging, flatten­ ing, or expanding operations of heat-treated aluminum alloy members, as it is difficult to control the temperatures closely enough to prevent possible damage to the metal, and it may impair its corrosion resistance.

j. Splicing of Stringers and Flanges. I t is recommended that all splices be made in ac­ cordance with the manufacturer’s recommen­ dations. If the manufacturer’s recommenda­ tions are not available, the typical splices for various shapes of sections are shown in figures 4-17 through 4-19. Design splices to carry both tension and compression, and use the splice shown in figure 4-18 as an example il­ lustrating the following principles.

(1) To avoid eccentric loading and con­ sequent buckling in compression, place splic­ ing or reinforcing parts as symmetrically as possible about the centerline of the member, and attach to as many elements as necessary to prevent bending in any direction.

(2) To avoid reducing the strength in tension of the original bulb angle, the rivet holes at the ends of the splice are made small (no larger than the original skin attaching riv­ ets), and the second row of holes (those through the bulbed leg) are staggered back from the ends. In general, arrange the rivets in the splice so that the design tensile load for the member and splice plate can be carried into the splice without failing the member at the out­ ermost rivet holes.

Par 4-58 Page 4-27

Page 169OCROpen in PDF

-L = 20 SPACES 3 d EACH -TOTAL NO. OF RIVETS - 18 (9 EACH SIDE OF SPLICE) A = ORIGINAL TUBE C = REPLACEMENT TUBE B = SLEEVE USE 2117-T ALUM. ALLOY RIVETS SMALL HEAD

HAMMER STANDARD SPLICES MAY BE USED ON LIGHTLY ROUND HEAD LONGERONS OR WEB MEMBERS.

CORRECT WAY INCORRECT WAY d MUST NOT BE LESS THAN D/8.

R = 3d

• • 0000

STREAMLINE M/3 EACH→ (USE BASIC ROUND SIZES IN TABLE FOR SIZE OF RIVETS ETC.)

A, C * 3/4 .065 7/8 065 .065 1 .065 1-1/8 1-1/4 058 1-/3/8 .058 .058 1-1/2 1-/5/8 .058 1-3/4 058 .058 1-7/8 B 7/8 1 1-1/8 1-1/4 1-3/8 1-1/2 1-5/8 1-3/4 1-7/8 2 ALL .058 THICK RIVET DIA 5/32 5/32 3/16 3/16 3/16 3/16 1/4 1/4 1/4 1/4 L 9-3/8 9-3/8 11-1/4 11-1/4 11-1/4 11-1/4 15 15 15 15 * INCLUDES ALL THICKNESSES UP TO AND INCLUDING MAXIMUM SHOWN.

NOTE. USE SAME MATERIAL AS ORIGINAL FOR SLEEVE AND REPLACEMENT TUBE.

FIGURE 4-12. Typical repair method for tubular members of aluminum alloy.

Page 4-28 Par 4-58

Page 170OCROpen in PDF

- A D- 30 30 30 202030 30 30 - D

AT LEAST AS THICK

AS ORIGINAL

ORIGINAL

REINFORGEMENT 2117-AD RIVETS MATERIAL - DURAL. OR ALUMINUM ALLOY USED IN 3/32" DIA. MIN.

ORIGINAL CONSTRUCTION.

SCALE - TWICE SIZE SECTION A-A

SCALE - TWICE SIZE 2017-T3 00010000 D SQ. ROD 30 3D 3D 3D 130 1 30, 30 30 3D_ +3D→ • 2117-AD RIVETS 1/8" DIA: MIN.

NOTE: FOR MINIMUM NUMBER OF RIVETS REQUIRED, SEE PARAGRAPH 4-58g AND SUBSEQUENT.

FIGURE 4-13. Typical repair for buckled or cracked metal wing rib capstrips.

Par 4-58 Page 4-29

Page 171OCROpen in PDF

SEE (C) SEE (D) TOOOK (A)

- SEE (E) (B) D = RIVET DIA.

›PROX.) (MINIMUM 3/32") D

BEND RADII TO FIT

ORIGINAL RIB.

(G) 16PLYWOOD TO STIFFEN BENT RIBS.

MACHINE SCREW D OR RIVET.

- 1.5 ₺ (APPROX.)

LPEEN (E) 30 2030. 20201970.32 (D) NOTE: FOR MINIMUM NUMBER OF RIVETS REQUIRED, SEE PARAGRAPH 4-58g AND SUBSEQUENT.

FIGURE 4-14. Typical metal rib repairs (usually found on small and medium-size aircraft).

Page 4-30 Par 4-58

Page 172OCROpen in PDF

"А" „040I 2017-T3 SPACER 2D, 3D 3D 202D 3D 3D 20 "В" 2024-T3 SPLICE BAR "Д" "В ". 9120 ---- ti 2117-AD RIVETS 3/32" DIA. MIN. - CRACK 2117-AD RIVETS 3/32" DIA. MIN. 4→ Д

- ЗА ЗА I. STRAIGHTEN CRIMPED OVER PORTION. CRACK

2. INSERT HARDWOOD (ASH) INSERT SHAPED.

TO CONFORM TO T.E. PIECE.

2117-AD RIVETS 20 20 20 2D D 3/32" DIA. MIN.

FLATTEN HEADS (APPROX. 1.5 ₺ ) OUTSIDE

1. STRAIGHTEN CRIMPED PORTION. - CRACK

2. USE SAME AL. ALLOY AS IN ORIGINAL.

NOTE: FOR MINIMUM NUMBER OF RIVETS REQUIRED, SEE PARAGRAPH 4-58g AND SUBSEQUENT.

FIGURE 4-15. Typical repairs of trailing edges.

Par 4-58 Page 4-31

Page 173OCROpen in PDF

(A) ADDED

STIFFENERS TO →15% 2 EACH BACK UP SEAM 24-5/32" PREQ'D OF PATCH.

2117-T4 BACKED PATCH PLATE

BY SAME TO BE OF SAME RIVETS †22-12 MATERIAL AS

ORIGINAL AND 3" HOLE MAX. DIA. HOLE MAX DIA. SAME OR NEXT HEAVIER GAUGE.

16-5/32" RIVET SIZE, -2117-T4 RIVETS SPACING,

MATERIAL, AND

PATTERN "G", "H", AND "K SAME AS ARE ORIGINAL A B.

CIRCULAR PATCH PLATES. DAMAGED SKIN DIMENSIONS OF CIR. PATCH PLATES SHOULD BE DESIGNATION "K" "H" "G" CLEANED OUT DIAMETER (OUTSIDE) 2-1/2" 5" 7-12" SMOOTHLY AS DIA. INNER RIVET CIRCLE 1-3/4" 3" 4" INDICATED BY DIA. OUTER RIVET CIRCLE 4" 6-1/2" CDEF.

SAME RIVET SIZE, SPACING, MATERIAL, & PATTERN AS B C.

SAME RIVET SIZE, SPACING, MATERIAL, & PATTERN AS A D.

PATCH PLATE

TO BE OF SAME

•1" HOLE MATERIAL AS 8-5/32" 2 MAX DIA. ORIGINAL AND

RI SAME OR NEXT

HEAVIER GAUGE CRACK D 2 TIMES LENGTI NOT LESS THAN -PORTION OF SKIN REPLACED OF CRACK:

- ORIGINAL SKIN SHEET. "4 RIVETS REQD. EACH SIDE.

RIVET SPACING AT LEAST 3X RIVET DIA

HOLES DRILLED TO PREVENT CRACK SPREADING.

SKIN GAUGE = .028" (B) RIVET DIA. = 1/8" CRACK 2.5" LONG' FIGURE 4-16. Typical repairs of stressed sheet metal coverings. (Refer to tables 4-9, 4-10, and 4-11 to calculate number of rivets to be used.)

Page 4-32 Par 4-58

Page 174OCROpen in PDF

86/8/6 AC 43.13-1B ....•......

ITAPERED SPLICE MEMBER NOTE: UNSHADED SECTIONS ARE ORIGINAL AND/OR REPLACEMENT SECTIONS. SHADED SECTIONS ARE CONNECTING OR REINFORCING SECTIONS.

NOTE: FOR MINIMUM NUMBER OF RIVETS REQUIRED, SEE PARAGRAPH 4-58g AND SUBSEQUENT.

FIGURE 4-17. Typical stringer and flange splices.

Par 4-58 Page 4-33

Page 175OCROpen in PDF

CUT IN STRINGER TAPERED SPLICE MEMBER 0-0

ON LOWER SURFACE OF WING, MAKE END RIVET SAME SIZE AS SKIN ATTACHING RIVETS.

2 oz, MINIMUM 3 dz, MINIMUM -

THE NUMBER OF BOLTS REQUIRED IN THE "BULB" LEG OF THE STRINGER IS DETERMINED FROM TABLE 4-9 FOR 2017-T3 AS FOLLOWS:

+z= 1/16" (Use .064") de= .190 (AN3 bolt) NO. OF BOLTS PER INCH OF WIDTH FROM TABLE = 3.3.

ACTUAL NO. OF BOLTS ON EACH SIDE OF CUT = WX 3.3 = (1.0) × 3.3 = 3.3 BOLTS USE 4 BOLTS

WHEN BOTH RIVETS AND BOLTS

ARE USED, BOLT HOLES SHOULD BE REAMED TO SIZE. (ź) -KEEP LARGE HOLES BACK FROM END OF SPLICE.

THE NUMBER OF RIVETS REQUIRED IN

THE UPPER LEG OF THE STRINGER IS DETERMINED FROMTABLE 4-9 FOR 2017-T3 AS FOLLOWS:

t, = 1/16" (Use „064") d,= 1/8" (2117-AD rivet) NO. OF RIVETS PER INCH OF WIDTH FROM TABLE = 9.9 ACTUAL NO. OF RIVETS ON EACH SIDE OF CUT = WIx 9.9 = (.5) × 9.9 = 4.95 RIVETS. USE 5 RIVETS.

d, (1/8), RIVET DIA. PREFERABLY 12tTO 3t, BUT NOT GREATER THAN W/4.

Wz.

(1.0)

- "B" SPLICE BAR. SHADED AREA SPLICE ANGLE "A" dz (16). GREATER THAN W, Xt,.

SHADED AREA GREATER THAN W2xt2. STRINGER

AREA REPRESENTING BULB

SECTION A-A FIGURE 4-18. Example of stringer splice (material-2017 alloy).

Page 4-34 Par 4-58